This patch fixes a bug where the advertising parameters weren't updated
after a call to "Set Connectable" if the HCI_ADVERTISING_INSTANCE
setting was set.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

With this patch, ADV_SCAN_IND will be used for advertising instances
that have non-zero scan response data while the global "connectable"
setting is "off".
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fixes a bug where ADV_NONCONN_IND was being used for
advertising instances >0 while the global connectable setting was
set to "on".
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

During the HCI init phase a completed request might be the last part of
the setup procedure after which the actual init procedure starts. The
init procedure begins with a call to hci_reset_req() which sets the
HCI_RESET flag. The purpose of this flag is to make us ignore any
updates to ncmd/cmd_cnt as long as we haven't received the command
complete event for the HCI_Reset. There's a potential race with this
however:

	hci_req_cmd_complete(hdev, opcode, status);

	if (ev->ncmd && !test_bit(HCI_RESET, &hdev->flags)) {
		atomic_set(&hdev->cmd_cnt, 1);
		if (!skb_queue_empty(&hdev->cmd_q))
			queue_work(hdev->workqueue, &hdev->cmd_work);
	}

Since the hci_req_cmd_complete() will trigger the completion of the
setup stage, it's possible that hci_reset_req() gets called before we
try to read ev->ncmd and the HCI_RESET flag. Because of this the cmd_cnt
would never be updated and the hci_reset_req() in practice ends up
blocking itself.

This patch fixes the issue by updating cmd_cnt before notifying the
request completion, and then reading it again to determine whether the
cmd_work should be queued or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For all modern Bluetooth USB devices from Broadcom it makes a lot more
sense to use USB_VENDOR_AND_INTERFACE_INFO instead of manually adding
USB_DEVICE for each one of them. There are already interface entries
for these vendors and so just remove the duplicate device entries.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This patch fix the error handling when is_tx is true. The error handling
tries to get the transceiver into RX_AACK_ON mode then we need to be
sure that is_tx is false.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This spinlock isn't necessary because if we are in TX_ON/TX_ARET_ON
state the transceiver can't be interrupted e.g. by receiving a frame
when a SHR was detected. In this time the transceiver doesn't leave
the TX_ON/TX_ARET_ON state until the tx complete irq change the state
into RX_AACK_ON again. This means a receiving interrupt in state
TX_ON/TX_ARET_ON can't happen and is_tx is protected by transceiver.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch cleanups the checking of different mac phy depended values by
handling depended mac settings per hw support flag in one condition.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch simplifies the code paths for assembling the advertising data
used by advertising instances 0 and 1.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch updates the "supported_flags" parameter returned from the
"Read Advertising Features" command. Add Advertising will now return
an error if an unsupported flag is provided.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for the "tx-power" flag of the Add
Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for the "managed-flags" flag of the Add
Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for the "limited-discoverable" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for the "discoverable" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for the "connectable mode" flag of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds macro definitions for possible advertising instance
flags that can be passed to the "Add Advertising" command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Some Bluetooth controllers require initialization before being
used (vendor config, firmware download). Add possibility for a
HCI UART proto to implement this early init via the setup callback.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When the user of the management interface is not trusted, then it only
has access to a limited set of commands and events. When providing the
list of supported commands and events take the trusted vs untrusted
status of the user into account and return different lists.

This way the untrusted user knows exactly which commands it can
execute and which events it can receive. So no guesswork needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This patch implements support for the timeout parameter of the
Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch implements setting the Scan Response data provided as part
of an advertising instance through the Add Advertising command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch implements the "Remove Advertising" mgmt command.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds the most basic implementation for the
"Add Advertisement" command. All state updates between the
various HCI settings (POWERED, ADVERTISING, ADVERTISING_INSTANCE,
and LE_ENABLED) has been implemented. The command currently
supports only setting the advertising data fields, with no flags
and no scan response data.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduces a new data structure to represent advertising
instances that were added using the "Add Advertising" mgmt command.
Initially an hci_dev structure will support only one of these instances
at a time, so the current instance is simply stored as a direct member
of hci_dev.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch introduces the HCI_ADVERTISING_INSTANCE setting, which is set
when an at least one advertising instance has been added using the
"Add Advertising" mgmt command. This patch also adds a macro definition
for the EIR_APPEARANCE field type.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds definitions for the Add Advertising and Remove
Advertising MGMT commands and events.
Signed-off-by: Arman Uguray <armansito@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For the Apple Bluetooth devices that are Broadcom based, it makes sense
to read the chip information. It is a single HCI command and might help
gathering more information about these devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

The hci_request in le_scan_disable_work_complete() was being initialized
in a general context but only used in a specific branch in the function
(when simultaneous discovery is not supported). This patch moves the
usage to be limited to the branch where hci_req_run() is actually
called.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Broadcom devices expose their chip id via Read Verbose Config
Version Info command. While this information is not used at the
moment, it might be useful for debugging purposes and so read it
before patching the firmware. This makes it show up in dmesg and
HCI traces taken for the system.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

This patch expose controller quirks through debugfs. It would be
useful for BlueZ tests using vhci. Currently there is no way to
test quirk dependent behaviour. It might be also useful for manual
testing.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Using the HCI_MAX_AD_LENGTH for the max advertising data and max scan
response data length makes more sense than hardcoding the value.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Currently the enabling of LE on LE only devices causes an error. This
is a bit difference from other commands where trying to set the same
existing settings causes a positive response. Fix this behavior for
this single corner case.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: b6eea9ca ("mac802154: introduce driver-ops header")
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.

Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.

This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.

The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Storing the `platform_data` struct inside of the SPI struct when using
the device tree allows for a later function to edit the content of that
struct. This patch refactors the `cc2520_get_platformat_data` function
to accept a pointer to a `cc2520_platform_data` struct and populates
the fields inside of it.

This change mirrors commit aaa1c4d2
("at86rf230: copy pdata to driver allocated space").
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When the allocation of the L2CAP channel for the BR/EDR security manager
fails, then the smp variable might be NULL. In that case do not try to
free the non-existing crypto contexts
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

OS X version 10.10.2 (and possibly older versions) doesn't support LE
Secure Connections but incorrectly copies all authentication request
bits from a Security Request to its Pairing Request. The result is that
an SC capable initiator (such as BlueZ) will think OS X intends to do SC
when in fact it's incapable of it:

< ACL Data TX: Handle 3585 flags 0x00 dlen 6
      SMP: Security Request (0x0b) len 1
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      SMP: Pairing Request (0x01) len 6
        IO capability: KeyboardDisplay (0x04)
        OOB data: Authentication data not present (0x00)
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
        Max encryption key size: 16
        Initiator key distribution: EncKey (0x01)
        Responder key distribution: EncKey IdKey Sign (0x07)
< ACL Data TX: Handle 3585 flags 0x00 dlen 11
      SMP: Pairing Response (0x02) len 6
        IO capability: NoInputNoOutput (0x03)
        OOB data: Authentication data not present (0x00)
        Authentication requirement: Bonding, No MITM, SC, No Keypresses (0x09)
        Max encryption key size: 16
        Initiator key distribution: EncKey (0x01)
        Responder key distribution: EncKey Sign (0x05)

The pairing eventually fails when we get an unexpected Pairing Confirm
PDU instead of a Public Key PDU:

> ACL Data RX: Handle 3585 flags 0x02 dlen 21
      SMP: Pairing Confirm (0x03) len 16
        Confim value: bcc3bed31b8f313a78ec3cce32685faf

It is only at this point that we can speculate that the remote doesn't
really support SC. This patch creates a workaround for the just-works
model, however the MITM case is unsolvable because the OS X user has
already been requested to enter a PIN which we're now expected to
randomly generate and show the user (i.e. a chicken-and-egg problem).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The mgmt.c file should be reserved purely for HCI_CHANNEL_CONTROL. The
mgmt_control() function in it is already completely generic and has a
single user in hci_sock.c. This patch moves the function there and
renames it a bit more appropriately to hci_mgmt_cmd() (as it's a command
dispatcher).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In order to make the mgmt command handling more generic we can't have a
direct call to mgmt_init_hdev() from mgmt_control(). This patch adds a
new callback to struct hci_mgmt_chan. And sets it to point to the
mgmt_init_hdev() function for the HCI_CHANNEL_CONTROL instance.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

There are several mgmt protocol features that will be needed by more
than just the current HCI_CHANNEL_CONTROL. These include sending generic
events as well as handling pending commands. This patch moves these
functions out from mgmt.c to a new mgmt_util.c file.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>