- 19 May, 2010 1 commit
-
-
Tejun Heo authored
1. pata_cmd640 is PIO only. Inherit from sff. 2. pata_macio is BMDMA. Inherit from bmdma and drop explicit bmdma_mode_filter() setting. 3. In sata_mv, unlike mv5, mv6 is BMDMA. Inherit from bmdma and don't clear ->post_internal_cmd(). 4. bf54x and icside are quasi-BMDMA controllers which don't use the standard BMDMA registers so they don't initialize bmdma_addr and inherit from sff to avoid the default mode_filter which disables DMA modes if bmdma_addr is not initialized. For 2 and 3, this patch makes the drivers explicitly specify ->mode_filter to ATA_OP_NULL while inheriting from ata_bmdma_port_ops. These will be removed by the next patch. This patch makes all and only BMDMA drivers inherit from ata_bmdma_port_ops to ease further SFF/BMDMA separation. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
- 18 May, 2010 3 commits
-
-
Tejun Heo authored
Reorder functions such that SFF and BMDMA functions are grouped. While at it, s/BMDMA/SFF in a few comments where it actually meant SFF. Signed-off-by:
-
Tejun Heo authored
sata_inic162x doesn't use PRD anymore. No need to initialize it. Signed-off-by:
-
Tejun Heo authored
ATA_FLAG_DISABLED is only used by drivers which don't use ->error_handler framework and is largely broken. Its only meaningful function is to make irq handlers skip processing if the flag is set, which is largely useless and even harmful as it makes those ports more likely to cause IRQ storms. Kill ATA_FLAG_DISABLED and makes the callers disable attached devices instead. ata_port_probe() and ata_port_disable() which manipulate the flag are also killed. This simplifies condition check in IRQ handlers. While updating IRQ handlers, remove ap NULL check as libata guarantees consecutive port allocation (unoccupied ports are initialized with dummies) and long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()). Signed-off-by:
-
- 15 May, 2010 8 commits
-
-
Tejun Heo authored
ata_irq_on() was renamed to ata_sff_irq_on() and exported a while ago but prototype for the original function lingered in drivers/ata/libata.h. Kill it. Also, ata_dev_select() is only used inside drivers/ata/libata-sff.c. Make it static. Signed-off-by:
-
Tejun Heo authored
* Clearing IRQ from ata_sff_error_handler() is necessary only when the port is gonna be thawed before performing EH actions and some controllers don't like being accessed after certain failure modes until they're reset. Clear IRQ iff the port is being thawed. * When the controller succesfully indicated bus error, the point of thawing doesn't matter. Move thawing inside bmdma part of EH. This is a bit ugly but will ease code reorganization later. * Remove the unneeded ata_sff_sync(). Signed-off-by:
-
Tejun Heo authored
sata_mv initializes unused ioports fields including bmdma_addr to NULL. As later changes will conditionalize BMDMA, this makes sata_mv unnecessarily dependent on BMDMA. Remove the unnecessary initialization. Signed-off-by:
-
Tejun Heo authored
sata_inic162x no longer uses SFF interface. Move it out of CONFIG_ATA_SFF. Signed-off-by:
-
Tejun Heo authored
pata_sch is standard SFF. No reason to open code init. Use ata_pci_sff_init_one() instead. Signed-off-by:
-
Alan Cox authored
Use our own mmio area to avoid PCI posting. This avoids the rather slow paranoid implementation in the default handler. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Alan Cox authored
We don't need to stall and wait after loading the task file and before issuing a command, so don't do it. This shows up on profiles and is not needed. Signed-off-by:
-
Tejun Heo authored
sata_nv was incorrectly using ata_host_activate() instead of ata_pci_sff_activate_host() leading to IRQ assignment failure in legacy mode. Fix it. Signed-off-by:
-
- 14 May, 2010 28 commits
-
-
Sebastian Andrzej Siewior authored
page_mapping() check this via VM_BUG_ON(PageSlab(page)) so we bug here with the according debuging turned on. Future TODO: replace this with a flush_dcache_page_for_pio() API Signed-off-by:
Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Signed-off-by:
-
Sergei Shtylyov authored
cmd640_hardware_init() reads CFR but doesn't use the value read... Signed-off-by:
Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by:
-
Sergei Shtylyov authored
Now, with the introduction of the sff_set_devctl() method, we can use it in sff_irq_on() method too -- that way its implementations in 'pata_bf54x' and 'pata_scc' become virtually identical to ata_sff_irq_on(). The sff_irq_on() method now becomes quite superfluous, and the only reason not to remove it completely is the existence of the 'pata_octeon_cf' driver which implements it as an empty function. Just make the method optional then, with ata_sff_irq_on() becoming generic taskfile-bound function, still global for the 'pata_bf54x' driver to be able to call it from its thaw() and postreset() methods. While at it, make the sff_irq_on() method and ata_sff_irq_on() return 'void' as the result is always ignored anyway. Signed-off-by:
-
Sergei Shtylyov authored
The set of libata's taskfile access methods is clearly incomplete as it lacks a method to write to the device control register -- which forces drivers like 'pata_bf54x' and 'pata_scc' to implement more "high level" (and more weighty) methods like freeze() and postreset(). So, introduce the optional sff_set_devctl() method which the drivers only have to implement if the standard iowrite8() can't be used (just like the existing sff_check_altstatus() method) and make use of it in the freeze() and postreset() method implementations (I could also have used it in softreset() method but it also reads other taskfile registers without using tf_read() making that quite pointless); this makes freeze() method implementations in the 'pata_bf54x' and 'pata_scc' methods virtually identical to ata_sff_freeze(), so we can get rid of them completely. Signed-off-by:
-
Jeff Garzik authored
Signed-off-by: -
Harry Zhang authored
Add "em_buffer" attribute for SATA AHCI hosts to provide a way for userland to access AHCI EM (enclosure management) buffer directly if the host supports EM. AHCI driver should support SGPIO EM messages. However the SATA/AHCI specs did not define the SGPIO message format filled in EM buffer. Different HW vendors may have different definitions. The mainly purpose of this attribute is to solve this issue by allowing HW vendors to provide userland drivers and tools for their SGPIO initiators. Signed-off-by:
Harry Zhang <harry.zhang@amd.com> Signed-off-by:
-
Harry Zhang authored
Detect enclosure management message type automatically at driver initialization, instead of using module parameter "ahci_em_messages". Signed-off-by:
-
Sergei Shtylyov authored
The device control register exists and its address is set by scc_setup_ports(), hence the check is useless... Signed-off-by:
-
Sergei Shtylyov authored
... since, of course, it's not used outside this driver. Signed-off-by:
-
Akinobu Mita authored
Use __ratelimit() instead of its own private rate limit implementation. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: linux-ide@vger.kernel.org Signed-off-by:
-
Tejun Heo authored
There are some SATA devices which take relatively long to get out of 0xff status after reset. In libata, this timeout is determined by ATA_TMOUT_FF_WAIT. Quantum GoVault is the worst requring about 2s for reliable detection. However, because 2s 0xff timeout can introduce rather long spurious delay during boot, libata has been compromising at the next longest timeout of 800ms for HHD424020F7SV00 iVDR drive. Now that parallel scan is in place for common drivers, libata can afford 2s 0xff timeout. Use 2s 0xff timeout if parallel scan is enabled. Please note that the chance of spurious wait is pretty slim w/ working SCR access so this will only affect SATA controllers w/o SCR access which isn't too common these days. Please read the following thread for more information on the GoVault drive. http://thread.gmane.org/gmane.linux.ide/14545/focus=14663Signed-off-by:
-
Sergei Shtylyov authored
... since I see no callers of it. Signed-off-by:
-
Grant Grundler authored
In 2009, While running "cache read" performance test of drives behind SII PMP we encountered a "all 5 drives" timeout on more than 30% of the machines under test. This patch reduces the rate by a factor of about 70. Low enough that we didn't care to further investigate the issue. Performance impact with any sort of "normal" use was ~2%+ CPU and less than 1% throughput degradation. Worst case impact (cached read) was 6% IOPS reduction. This is with NCQ off (q=1) but I believe FIS based switching enabled in the SATA driver. The patch disables "Early ACK" in the 3726 port multiplier. "Early ACK" is issued when device sends a FIS to the host (via PMP) and the PMP sends an ACK immediately back to the device - well before the host gets the response. Under worst case IOPs load (cached read test) and more than 2 PMPs connected to a 4-port SATA controller, I suspect the time to service all of the PMPs is exceeding the PMPs ability to keep track of outstanding FIS it owes the Host. Reducing the number of PMPs to 2 (or 1) reduces the frequency by several orders of magnitude. Kudos to Gwendal for initial debugging of this issue. [Any errors in the description are mine, not his.] Patch is currently in production on Google servers. Signed-off-by:
Grant Grundler <grundler@google.com> Signed-off-by:
Gwendal Grignou <gwendal@google.com> Acked-by:
-
Tejun Heo authored
Implicit slab.h inclusion via percpu.h is about to go away. Make sure gfp.h or slab.h is included as necessary. Signed-off-by:
-
Tejun Heo authored
It turns out different generations of MCPs have differing quirks. * MCP 65-73 : FPDMA AA broken, lies about PMP support, forgets to report NCQ * MCP 77-79 : FPDMA AA broken, lies about PMP support * MCP 89 : FPDMA AA broken Instead of turngin off FPDMA AA on all NVIDIAs, implement HFLAG_NO_FPDMA_AA, define additional board IDs and apply necessary quirks. This fixes bko#15481 and the list of quirks is verified by Peer Chen. http://bugzilla.kernel.org/show_bug.cgi?id=15481Signed-off-by:
-
Roman Fietze authored
I've prepared a totally simple patch that, if I did it and measured it correctly, reduces the text size as of the ppc-6xx-size command of pata-mpc52xx by more than 10%, by reducing the rodata size from 0x4a4 to 0x17e bytes. This is simply done by changing the data types of the ATA timing constants. If you are interested at all, and it's worth the trouble, here the details: ppc-6xx-size: text data bss dec hex filename old: 6532 1068 0 7600 1db0 pata-mpc52xx.o new: 5718 1068 0 6786 1a82 pata-mpc52xx.o The (assembler) code itself doesn't really change very much. I double checked the final results inside mpc52xx-ata-apply-timings() and they match. The driver is still working fine of course. Signed-off-by:Roman Fietze <roman.fietze@telemotive.de> Signed-off-by:
-
Tejun Heo authored
ahci over time has grown a number of board IDs and it's a bit of mess right now. Clean it up such that, * board_id_* now live in a separate enum board_ids and numbers are assigned automatically. * Board IDs assigned to features are separated from the ones assigned to specific implementations and both are ordered alphabetically. * For NV MCPs, define per-generation alias board_ids and assign matching aliases in the pci id table. This makes mcp_linux, 67-73 use board_ahci_mcp65 instead of board_ahci_yesncq. Both are identical in content. * Kill now unused board_ahci_nopmp and board_ahci_yesncq. This patch doesn't cause any functional change but will make future changes to board_ids and quirks much less painful. Signed-off-by:
-
Matthew Garrett authored
According to section 10.3.1 of the AHCI spec, PxCMD.ST must not be set unless there's a device attached. Following this saves us a measurable quantity of power and does not impair hotplug support. Based on a patch by Kristen Carlson Accardi. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by:
-
Anton Vorontsov authored
This can be used for AHCI-compatible interfaces implemented inside System-On-Chip solutions, or AHCI devices connected via localbus. Signed-off-by:
Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
-
Anton Vorontsov authored
This patch should contain no functional changes, just moves code around. Signed-off-by:
-
Anton Vorontsov authored
Factor out some ahci_em_messages handling code from ahci_init_one(). We would like to reuse it for non-PCI devices. Signed-off-by:
-
Anton Vorontsov authored
Introduce ahci_pci_print_info() that now handles PCI stuff. Signed-off-by:
-
Anton Vorontsov authored
Move PCI stuff into ahci_pci_init_controller(). Signed-off-by:
-
Anton Vorontsov authored
To make the function bus-independand we have to get rid of "struct pci_dev *", so let's pass just "struct devce *". Signed-off-by:
-
Anton Vorontsov authored
Move PCI stuff into ahci_pci_reset_controller(). Signed-off-by:
-
Anton Vorontsov authored
To make the function generic we have to get rid of "struct pci_dev *", so let's pass just a "struct devce *". Signed-off-by:
-
Anton Vorontsov authored
Make ahci_save_initial_config() a bit more generic by introducing force_port_map and mask_port_map arguments. Move PCI stuff into ahci_pci_save_initial_config(). Signed-off-by:
-
Anton Vorontsov authored
Currently the driver uses host->iomap to store all the iomapped BARs of a PCI device (while AHCI devices actually use just a single memory window). We're going to teach AHCI to work with non-PCI buses, so there are two options to make this work: 1. "fake" host->iomap array for non-PCI devices, and place the needed address at iomap[AHCI_PCI_BAR]; 2. Get rid of host->iomap usage, instead introduce a private mmio field. This patch implements the second option. Signed-off-by:
-
