After running command [2] too many times in a row:

[1] $ tc qdisc add dev sw2p0 root handle 1: mqprio num_tc 8 \
	map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
[2] $ tc qdisc replace dev sw2p0 parent 1:1 cbs offload 1 \
	idleslope 120000 sendslope -880000 locredit -1320 hicredit 180

(aka more than priv->info->num_cbs_shapers times)

we start seeing the following error message:

Error: Specified device failed to setup cbs hardware offload.

This comes from the fact that ndo_setup_tc(TC_SETUP_QDISC_CBS) presents
the same API for the qdisc create and replace cases, and the sja1105
driver fails to distinguish between the 2. Thus, it always thinks that
it must allocate the same shaper for a {port, queue} pair, when it may
instead have to replace an existing one.

Fixes: 4d752508 ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

More careful measurement of the tc-cbs bandwidth shows that the stream
bandwidth (effectively idleslope) increases, there is a larger and
larger discrepancy between the rate limit obtained by the software
Qdisc, and the rate limit obtained by its offloaded counterpart.

The discrepancy becomes so large, that e.g. at an idleslope of 40000
(40Mbps), the offloaded cbs does not actually rate limit anything, and
traffic will pass at line rate through a 100 Mbps port.

The reason for the discrepancy is that the hardware documentation I've
been following is incorrect. UM11040.pdf (for SJA1105P/Q/R/S) states
about IDLE_SLOPE that it is "the rate (in unit of bytes/sec) at which
the credit counter is increased".

Cross-checking with UM10944.pdf (for SJA1105E/T) and UM11107.pdf
(for SJA1110), the wording is different: "This field specifies the
value, in bytes per second times link speed, by which the credit counter
is increased".

So there's an extra scaling for link speed that the driver is currently
not accounting for, and apparently (empirically), that link speed is
expressed in Kbps.

I've pondered whether to pollute the sja1105_mac_link_up()
implementation with CBS shaper reprogramming, but I don't think it is
worth it. IMO, the UAPI exposed by tc-cbs requires user space to
recalculate the sendslope anyway, since the formula for that depends on
port_transmit_rate (see man tc-cbs), which is not an invariant from tc's
perspective.

So we use the offload->sendslope and offload->idleslope to deduce the
original port_transmit_rate from the CBS formula, and use that value to
scale the offload->sendslope and offload->idleslope to values that the
hardware understands.

Some numerical data points:

 40Mbps stream, max interfering frame size 1500, port speed 100M
 ---------------------------------------------------------------

 tc-cbs parameters:
 idleslope 40000 sendslope -60000 locredit -900 hicredit 600

 which result in hardware values:

 Before (doesn't work)           After (works)
 credit_hi    600                600
 credit_lo    900                900
 send_slope   7500000            75
 idle_slope   5000000            50

 40Mbps stream, max interfering frame size 1500, port speed 1G
 -------------------------------------------------------------

 tc-cbs parameters:
 idleslope 40000 sendslope -960000 locredit -1440 hicredit 60

 which result in hardware values:

 Before (doesn't work)           After (works)
 credit_hi    60                 60
 credit_lo    1440               1440
 send_slope   120000000          120
 idle_slope   5000000            5

 5.12Mbps stream, max interfering frame size 1522, port speed 100M
 -----------------------------------------------------------------

 tc-cbs parameters:
 idleslope 5120 sendslope -94880 locredit -1444 hicredit 77

 which result in hardware values:

 Before (doesn't work)           After (works)
 credit_hi    77                 77
 credit_lo    1444               1444
 send_slope   11860000           118
 idle_slope   640000             6

Tested on SJA1105T, SJA1105S and SJA1110A, at 1Gbps and 100Mbps.

Fixes: 4d752508 ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Change MIN_TXD and MIN_RXD to allow set rx/tx value between 64 and 80

Olga Zaborska says:

Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igb, igbvf and igc devices can use as low as 64
descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ACL flow table is required in switchdev mode when metadata is enabled,
driver creates such table when loading each vport. However, not every
vport is loaded in switchdev mode. Such as ECPF if it's the eswitch manager.
In this case, ACL flow table is still needed.

To make it modularized, create ACL flow table for eswitch manager as
default and skip such operations when loading manager vport.

Also, there is no need to load the eswitch manager vport in switchdev mode.
This means there is no need to load it on regular connect-x HCAs where
the PF is the eswitch manager. This will avoid creating duplicate ACL
flow table for host PF vport.

Fixes: 29bcb6e4 ("net/mlx5e: E-Switch, Use metadata for vport matching in send-to-vport rules")
Fixes: eb8e9fae ("mlx5/core: E-Switch, Allocate ECPF vport if it's an eswitch manager")
Fixes: 5019833d ("net/mlx5: E-switch, Introduce helper function to enable/disable vports")
Signed-off-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the cited commit, the mirred devices are recorded and checked while
parsing the actions. In order to avoid system crash, the duplicate
action in a single rule is not allowed.

But the rule is actually break down into several FTEs in different
tables, for either mirroring, or the specified types of actions which
use post action infrastructure.

It will reject certain action list by mistake, for example:
    actions:enp8s0f0_1,set(ipv4(ttl=63)),enp8s0f0_0,enp8s0f0_1.
Here the rule is split to two FTEs because of pedit action.

To fix this issue, when parsing the rule actions, reset if_count to
clear the mirred devices array if the rule is split to multiple
FTEs, and then the duplicate checking is restarted.

Fixes: 554fe75c ("net/mlx5e: Avoid duplicating rule destinations")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot/KCSAN reported data-races in iptunnel_xmit_stats() [1]

This can run from multiple cpus without mutual exclusion.

Adopt SMP safe DEV_STATS_INC() to update dev->stats fields.

[1]
BUG: KCSAN: data-race in iptunnel_xmit / iptunnel_xmit

read-write to 0xffff8881353df170 of 8 bytes by task 30263 on cpu 1:
iptunnel_xmit_stats include/net/ip_tunnels.h:493 [inline]
iptunnel_xmit+0x432/0x4a0 net/ipv4/ip_tunnel_core.c:87
ip_tunnel_xmit+0x1477/0x1750 net/ipv4/ip_tunnel.c:831
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:662
__netdev_start_xmit include/linux/netdevice.h:4889 [inline]
netdev_start_xmit include/linux/netdevice.h:4903 [inline]
xmit_one net/core/dev.c:3544 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3560
__dev_queue_xmit+0xeee/0x1de0 net/core/dev.c:4340
dev_queue_xmit include/linux/netdevice.h:3082 [inline]
__bpf_tx_skb net/core/filter.c:2129 [inline]
__bpf_redirect_no_mac net/core/filter.c:2159 [inline]
__bpf_redirect+0x723/0x9c0 net/core/filter.c:2182
____bpf_clone_redirect net/core/filter.c:2453 [inline]
bpf_clone_redirect+0x16c/0x1d0 net/core/filter.c:2425
___bpf_prog_run+0xd7d/0x41e0 kernel/bpf/core.c:1954
__bpf_prog_run512+0x74/0xa0 kernel/bpf/core.c:2195
bpf_dispatcher_nop_func include/linux/bpf.h:1181 [inline]
__bpf_prog_run include/linux/filter.h:609 [inline]
bpf_prog_run include/linux/filter.h:616 [inline]
bpf_test_run+0x15d/0x3d0 net/bpf/test_run.c:423
bpf_prog_test_run_skb+0x77b/0xa00 net/bpf/test_run.c:1045
bpf_prog_test_run+0x265/0x3d0 kernel/bpf/syscall.c:3996
__sys_bpf+0x3af/0x780 kernel/bpf/syscall.c:5353
__do_sys_bpf kernel/bpf/syscall.c:5439 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5437 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5437
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

read-write to 0xffff8881353df170 of 8 bytes by task 30249 on cpu 0:
iptunnel_xmit_stats include/net/ip_tunnels.h:493 [inline]
iptunnel_xmit+0x432/0x4a0 net/ipv4/ip_tunnel_core.c:87
ip_tunnel_xmit+0x1477/0x1750 net/ipv4/ip_tunnel.c:831
__gre_xmit net/ipv4/ip_gre.c:469 [inline]
ipgre_xmit+0x516/0x570 net/ipv4/ip_gre.c:662
__netdev_start_xmit include/linux/netdevice.h:4889 [inline]
netdev_start_xmit include/linux/netdevice.h:4903 [inline]
xmit_one net/core/dev.c:3544 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3560
__dev_queue_xmit+0xeee/0x1de0 net/core/dev.c:4340
dev_queue_xmit include/linux/netdevice.h:3082 [inline]
__bpf_tx_skb net/core/filter.c:2129 [inline]
__bpf_redirect_no_mac net/core/filter.c:2159 [inline]
__bpf_redirect+0x723/0x9c0 net/core/filter.c:2182
____bpf_clone_redirect net/core/filter.c:2453 [inline]
bpf_clone_redirect+0x16c/0x1d0 net/core/filter.c:2425
___bpf_prog_run+0xd7d/0x41e0 kernel/bpf/core.c:1954
__bpf_prog_run512+0x74/0xa0 kernel/bpf/core.c:2195
bpf_dispatcher_nop_func include/linux/bpf.h:1181 [inline]
__bpf_prog_run include/linux/filter.h:609 [inline]
bpf_prog_run include/linux/filter.h:616 [inline]
bpf_test_run+0x15d/0x3d0 net/bpf/test_run.c:423
bpf_prog_test_run_skb+0x77b/0xa00 net/bpf/test_run.c:1045
bpf_prog_test_run+0x265/0x3d0 kernel/bpf/syscall.c:3996
__sys_bpf+0x3af/0x780 kernel/bpf/syscall.c:5353
__do_sys_bpf kernel/bpf/syscall.c:5439 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5437 [inline]
__x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5437
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x0000000000018830 -> 0x0000000000018831

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 30249 Comm: syz-executor.4 Not tainted 6.5.0-syzkaller-11704-g3f86ed6e #0

Fixes: 039f5062 ("ip_tunnel: Move stats update to iptunnel_xmit()")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

team interface has used a dynamic lockdep key to avoid false-positive
lockdep deadlock detection. Virtual interfaces such as team usually
have their own lock for protecting private data.
These interfaces can be nested.
team0
  |
team1

Each interface's lock is actually different(team0->lock and team1->lock).
So,
mutex_lock(&team0->lock);
mutex_lock(&team1->lock);
mutex_unlock(&team1->lock);
mutex_unlock(&team0->lock);
The above case is absolutely safe. But lockdep warns about deadlock.
Because the lockdep understands these two locks are same. This is a
false-positive lockdep warning.

So, in order to avoid this problem, the team interfaces started to use
dynamic lockdep key. The false-positive problem was fixed, but it
introduced a new problem.

When the new team virtual interface is created, it registers a dynamic
lockdep key(creates dynamic lockdep key) and uses it. But there is the
limitation of the number of lockdep keys.
So, If so many team interfaces are created, it consumes all lockdep keys.
Then, the lockdep stops to work and warns about it.

In order to fix this problem, team interfaces use the subclass instead
of the dynamic key. So, when a new team interface is created, it doesn't
register(create) a new lockdep, but uses existed subclass key instead.
It is already used by the bonding interface for a similar case.

As the bonding interface does, the subclass variable is the same as
the 'dev->nested_level'. This variable indicates the depth in the stacked
interface graph.

The 'dev->nested_level' is protected by RTNL and RCU.
So, 'mutex_lock_nested()' for 'team->lock' requires RTNL or RCU.
In the current code, 'team->lock' is usually acquired under RTNL, there is
no problem with using 'dev->nested_level'.

The 'team_nl_team_get()' and The 'lb_stats_refresh()' functions acquire
'team->lock' without RTNL.
But these don't iterate their own ports nested so they don't need nested
lock.

Reproducer:
   for i in {0..1000}
   do
           ip link add team$i type team
           ip link add dummy$i master team$i type dummy
           ip link set dummy$i up
           ip link set team$i up
   done

Splat looks like:
   BUG: MAX_LOCKDEP_ENTRIES too low!
   turning off the locking correctness validator.
   Please attach the output of /proc/lock_stat to the bug report
   CPU: 0 PID: 4104 Comm: ip Not tainted 6.5.0-rc7+ #45
   Call Trace:
    <TASK>
   dump_stack_lvl+0x64/0xb0
   add_lock_to_list+0x30d/0x5e0
   check_prev_add+0x73a/0x23a0
   ...
   sock_def_readable+0xfe/0x4f0
   netlink_broadcast+0x76b/0xac0
   nlmsg_notify+0x69/0x1d0
   dev_open+0xed/0x130
   ...

Reported-by: syzbot+9bbbacfbf1e04d5221f7@syzkaller.appspotmail.com
Fixes: 369f61be ("team: fix nested locking lockdep warning")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__skb_get_hash_symmetric() was added to compute a symmetric hash over
the protocol, addresses and transport ports, by commit eb70db87
("packet: Use symmetric hash for PACKET_FANOUT_HASH."). It uses
flow_keys_dissector_symmetric_keys as the flow_dissector to incorporate
IPv4 addresses, IPv6 addresses and ports. However, it should not specify
the flag as FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL, which stops further
dissection when an IPv6 flow label is encountered, making transport
ports not being incorporated in such case.

As a consequence, the symmetric hash is based on 5-tuple for IPv4 but
3-tuple for IPv6 when flow label is present. It caused a few problems,
e.g. when nft symhash and openvswitch l4_sym rely on the symmetric hash
to perform load balancing as different L4 flows between two given IPv6
addresses would always get the same symmetric hash, leading to uneven
traffic distribution.

Removing the use of FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL makes sure the
symmetric hash is based on 5-tuple for both IPv4 and IPv6 consistently.

Fixes: eb70db87 ("packet: Use symmetric hash for PACKET_FANOUT_HASH.")
Reported-by: Lars Ekman <uablrek@gmail.com>
Closes: https://github.com/antrea-io/antrea/issues/5457Signed-off-by: Quan Tian <qtian@vmware.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igb devices can use as low as 64 descriptors.
This change will unify igb with other drivers.
Based on commit 7b1be198 ("e1000e: lower ring minimum size to 64")

Fixes: 9d5c8243 ("igb: PCI-Express 82575 Gigabit Ethernet driver")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igbvf devices can use as low as 64 descriptors.
This change will unify igbvf with other drivers.
Based on commit 7b1be198 ("e1000e: lower ring minimum size to 64")

Fixes: d4e0fe01 ("igbvf: add new driver to support 82576 virtual functions")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Change the minimum value of RX/TX descriptors to 64 to enable setting the rx/tx
value between 64 and 80. All igc devices can use as low as 64 descriptors.
This change will unify igc with other drivers.
Based on commit 7b1be198 ("e1000e: lower ring minimum size to 64")

Fixes: 0507ef8a ("igc: Add transmit and receive fastpath and interrupt handlers")
Signed-off-by: Olga Zaborska <olga.zaborska@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The smq value used in the CN10K NIX AQ instruction enqueue mailbox
handler was truncated to 9-bit value from 10-bit value because of
typecasting the CN10K mbox request structure to the CN9K structure.
Though this hasn't caused any problems when programming the NIX SQ
context to the HW because the context structure is the same size.
However, this causes a problem when accessing the structure parameters.
This patch reads the right smq value for each platform.

Fixes: 30077d21 ("octeontx2-af: cn10k: Update NIX/NPA context structure")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a follow up of commit 915d975b ("net: deal with integer
overflows in kmalloc_reserve()") based on David Laight feedback.

Back in 2010, I failed to realize malicious users could set dev->mtu
to arbitrary values. This mtu has been since limited to 0x7fffffff but
regardless of how big dev->mtu is, it makes no sense for igmpv3_newpack()
to allocate more than IP_MAX_MTU and risk various skb fields overflows.

Fixes: 57e1ab6e ("igmp: refine skb allocations")
Link: https://lore.kernel.org/netdev/d273628df80f45428e739274ab9ecb72@AcuMS.aculab.com/Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Laight <David.Laight@ACULAB.COM>
Cc: Kyle Zeng <zengyhkyle@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit ab046a5d.

It was trying to work around an issue at the crypto layer by excluding
ASYNC implementations of gcm(aes), because a bug in the AESNI version
caused reordering when some requests bypassed the cryptd queue while
older requests were still pending on the queue.

This was fixed by commit 38b2f68b ("crypto: aesni - Fix cryptd
reordering problem on gcm"), which pre-dates ab046a5d.

Herbert Xu confirmed that all ASYNC implementations are expected to
maintain the ordering of completions wrt requests, so we can use them
in MACsec.

On my test machine, this restores the performance of a single netperf
instance, from 1.4Gbps to 4.4Gbps.

Link: https://lore.kernel.org/netdev/9328d206c5d9f9239cae27e62e74de40b258471d.1692279161.git.sd@queasysnail.net/T/
Link: https://lore.kernel.org/netdev/1b0cec71-d084-8153-2ba4-72ce71abeb65@byu.edu/
Link: https://lore.kernel.org/netdev/d335ddaa-18dc-f9f0-17ee-9783d3b2ca29@mailbox.tu-dresden.de/
Fixes: ab046a5d ("net: macsec: preserve ingress frame ordering")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/11c952469d114db6fb29242e1d9545e61f52f512.1693757159.git.sd@queasysnail.netSigned-off-by: Paolo Abeni <pabeni@redhat.com>

kcm_exit_net() should call mutex_destroy() on knet->mutex. This is especially
needed if CONFIG_DEBUG_MUTEXES is enabled.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Link: https://lore.kernel.org/r/20230902170708.1727999-1-syoshida@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When the plug qdisc is used as a class of the qfq qdisc it could trigger a
UAF. This issue can be reproduced with following commands:

  tc qdisc add dev lo root handle 1: qfq
  tc class add dev lo parent 1: classid 1:1 qfq weight 1 maxpkt 512
  tc qdisc add dev lo parent 1:1 handle 2: plug
  tc filter add dev lo parent 1: basic classid 1:1
  ping -c1 127.0.0.1

and boom:

[  285.353793] BUG: KASAN: slab-use-after-free in qfq_dequeue+0xa7/0x7f0
[  285.354910] Read of size 4 at addr ffff8880bad312a8 by task ping/144
[  285.355903]
[  285.356165] CPU: 1 PID: 144 Comm: ping Not tainted 6.5.0-rc3+ #4
[  285.357112] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-2 04/01/2014
[  285.358376] Call Trace:
[  285.358773]  <IRQ>
[  285.359109]  dump_stack_lvl+0x44/0x60
[  285.359708]  print_address_description.constprop.0+0x2c/0x3c0
[  285.360611]  kasan_report+0x10c/0x120
[  285.361195]  ? qfq_dequeue+0xa7/0x7f0
[  285.361780]  qfq_dequeue+0xa7/0x7f0
[  285.362342]  __qdisc_run+0xf1/0x970
[  285.362903]  net_tx_action+0x28e/0x460
[  285.363502]  __do_softirq+0x11b/0x3de
[  285.364097]  do_softirq.part.0+0x72/0x90
[  285.364721]  </IRQ>
[  285.365072]  <TASK>
[  285.365422]  __local_bh_enable_ip+0x77/0x90
[  285.366079]  __dev_queue_xmit+0x95f/0x1550
[  285.366732]  ? __pfx_csum_and_copy_from_iter+0x10/0x10
[  285.367526]  ? __pfx___dev_queue_xmit+0x10/0x10
[  285.368259]  ? __build_skb_around+0x129/0x190
[  285.368960]  ? ip_generic_getfrag+0x12c/0x170
[  285.369653]  ? __pfx_ip_generic_getfrag+0x10/0x10
[  285.370390]  ? csum_partial+0x8/0x20
[  285.370961]  ? raw_getfrag+0xe5/0x140
[  285.371559]  ip_finish_output2+0x539/0xa40
[  285.372222]  ? __pfx_ip_finish_output2+0x10/0x10
[  285.372954]  ip_output+0x113/0x1e0
[  285.373512]  ? __pfx_ip_output+0x10/0x10
[  285.374130]  ? icmp_out_count+0x49/0x60
[  285.374739]  ? __pfx_ip_finish_output+0x10/0x10
[  285.375457]  ip_push_pending_frames+0xf3/0x100
[  285.376173]  raw_sendmsg+0xef5/0x12d0
[  285.376760]  ? do_syscall_64+0x40/0x90
[  285.377359]  ? __static_call_text_end+0x136578/0x136578
[  285.378173]  ? do_syscall_64+0x40/0x90
[  285.378772]  ? kasan_enable_current+0x11/0x20
[  285.379469]  ? __pfx_raw_sendmsg+0x10/0x10
[  285.380137]  ? __sock_create+0x13e/0x270
[  285.380673]  ? __sys_socket+0xf3/0x180
[  285.381174]  ? __x64_sys_socket+0x3d/0x50
[  285.381725]  ? entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[  285.382425]  ? __rcu_read_unlock+0x48/0x70
[  285.382975]  ? ip4_datagram_release_cb+0xd8/0x380
[  285.383608]  ? __pfx_ip4_datagram_release_cb+0x10/0x10
[  285.384295]  ? preempt_count_sub+0x14/0xc0
[  285.384844]  ? __list_del_entry_valid+0x76/0x140
[  285.385467]  ? _raw_spin_lock_bh+0x87/0xe0
[  285.386014]  ? __pfx__raw_spin_lock_bh+0x10/0x10
[  285.386645]  ? release_sock+0xa0/0xd0
[  285.387148]  ? preempt_count_sub+0x14/0xc0
[  285.387712]  ? freeze_secondary_cpus+0x348/0x3c0
[  285.388341]  ? aa_sk_perm+0x177/0x390
[  285.388856]  ? __pfx_aa_sk_perm+0x10/0x10
[  285.389441]  ? check_stack_object+0x22/0x70
[  285.390032]  ? inet_send_prepare+0x2f/0x120
[  285.390603]  ? __pfx_inet_sendmsg+0x10/0x10
[  285.391172]  sock_sendmsg+0xcc/0xe0
[  285.391667]  __sys_sendto+0x190/0x230
[  285.392168]  ? __pfx___sys_sendto+0x10/0x10
[  285.392727]  ? kvm_clock_get_cycles+0x14/0x30
[  285.393328]  ? set_normalized_timespec64+0x57/0x70
[  285.393980]  ? _raw_spin_unlock_irq+0x1b/0x40
[  285.394578]  ? __x64_sys_clock_gettime+0x11c/0x160
[  285.395225]  ? __pfx___x64_sys_clock_gettime+0x10/0x10
[  285.395908]  ? _copy_to_user+0x3e/0x60
[  285.396432]  ? exit_to_user_mode_prepare+0x1a/0x120
[  285.397086]  ? syscall_exit_to_user_mode+0x22/0x50
[  285.397734]  ? do_syscall_64+0x71/0x90
[  285.398258]  __x64_sys_sendto+0x74/0x90
[  285.398786]  do_syscall_64+0x64/0x90
[  285.399273]  ? exit_to_user_mode_prepare+0x1a/0x120
[  285.399949]  ? syscall_exit_to_user_mode+0x22/0x50
[  285.400605]  ? do_syscall_64+0x71/0x90
[  285.401124]  entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[  285.401807] RIP: 0033:0x495726
[  285.402233] Code: ff ff ff f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 11 b8 2c 00 00 00 0f 09
[  285.404683] RSP: 002b:00007ffcc25fb618 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
[  285.405677] RAX: ffffffffffffffda RBX: 0000000000000040 RCX: 0000000000495726
[  285.406628] RDX: 0000000000000040 RSI: 0000000002518750 RDI: 0000000000000000
[  285.407565] RBP: 00000000005205ef R08: 00000000005f8838 R09: 000000000000001c
[  285.408523] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000002517634
[  285.409460] R13: 00007ffcc25fb6f0 R14: 0000000000000003 R15: 0000000000000000
[  285.410403]  </TASK>
[  285.410704]
[  285.410929] Allocated by task 144:
[  285.411402]  kasan_save_stack+0x1e/0x40
[  285.411926]  kasan_set_track+0x21/0x30
[  285.412442]  __kasan_slab_alloc+0x55/0x70
[  285.412973]  kmem_cache_alloc_node+0x187/0x3d0
[  285.413567]  __alloc_skb+0x1b4/0x230
[  285.414060]  __ip_append_data+0x17f7/0x1b60
[  285.414633]  ip_append_data+0x97/0xf0
[  285.415144]  raw_sendmsg+0x5a8/0x12d0
[  285.415640]  sock_sendmsg+0xcc/0xe0
[  285.416117]  __sys_sendto+0x190/0x230
[  285.416626]  __x64_sys_sendto+0x74/0x90
[  285.417145]  do_syscall_64+0x64/0x90
[  285.417624]  entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[  285.418306]
[  285.418531] Freed by task 144:
[  285.418960]  kasan_save_stack+0x1e/0x40
[  285.419469]  kasan_set_track+0x21/0x30
[  285.419988]  kasan_save_free_info+0x27/0x40
[  285.420556]  ____kasan_slab_free+0x109/0x1a0
[  285.421146]  kmem_cache_free+0x1c2/0x450
[  285.421680]  __netif_receive_skb_core+0x2ce/0x1870
[  285.422333]  __netif_receive_skb_one_core+0x97/0x140
[  285.423003]  process_backlog+0x100/0x2f0
[  285.423537]  __napi_poll+0x5c/0x2d0
[  285.424023]  net_rx_action+0x2be/0x560
[  285.424510]  __do_softirq+0x11b/0x3de
[  285.425034]
[  285.425254] The buggy address belongs to the object at ffff8880bad31280
[  285.425254]  which belongs to the cache skbuff_head_cache of size 224
[  285.426993] The buggy address is located 40 bytes inside of
[  285.426993]  freed 224-byte region [ffff8880bad31280, ffff8880bad31360)
[  285.428572]
[  285.428798] The buggy address belongs to the physical page:
[  285.429540] page:00000000f4b77674 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xbad31
[  285.430758] flags: 0x100000000000200(slab|node=0|zone=1)
[  285.431447] page_type: 0xffffffff()
[  285.431934] raw: 0100000000000200 ffff88810094a8c0 dead000000000122 0000000000000000
[  285.432757] raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000
[  285.433562] page dumped because: kasan: bad access detected
[  285.434144]
[  285.434320] Memory state around the buggy address:
[  285.434828]  ffff8880bad31180: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  285.435580]  ffff8880bad31200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  285.436264] >ffff8880bad31280: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  285.436777]                                   ^
[  285.437106]  ffff8880bad31300: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
[  285.437616]  ffff8880bad31380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[  285.438126] ==================================================================
[  285.438662] Disabling lock debugging due to kernel taint

Fix this by:
1. Changing sch_plug's .peek handler to qdisc_peek_dequeued(), a
function compatible with non-work-conserving qdiscs
2. Checking the return value of qdisc_dequeue_peeked() in sch_qfq.

Fixes: 462dbc91 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Reported-by: valis <sec@valis.email>
Signed-off-by: valis <sec@valis.email>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20230901162237.11525-1-jhs@mojatatu.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Kuniyuki Iwashima says:

====================
af_unix: Fix four data-races.

While running syzkaller, KCSAN reported 3 data-races with
systemd-coredump using AF_UNIX sockets.

This series fixes the three and another one inspiered by
one of the reports.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As with sk->sk_shutdown shown in the previous patch, sk->sk_err can be
read locklessly by unix_dgram_sendmsg().

Let's use READ_ONCE() for sk_err as well.

Note that the writer side is marked by commit cc04410a ("af_unix:
annotate lockless accesses to sk->sk_err").

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_shutdown is changed under unix_state_lock(sk), but
unix_dgram_sendmsg() calls two functions to read sk_shutdown locklessly.

  sock_alloc_send_pskb
  `- sock_wait_for_wmem

Let's use READ_ONCE() there.

Note that the writer side was marked by commit e1d09c2c ("af_unix:
Fix data races around sk->sk_shutdown.").

BUG: KCSAN: data-race in sock_alloc_send_pskb / unix_release_sock

write (marked) to 0xffff8880069af12c of 1 bytes by task 1 on cpu 1:
 unix_release_sock+0x75c/0x910 net/unix/af_unix.c:631
 unix_release+0x59/0x80 net/unix/af_unix.c:1053
 __sock_release+0x7d/0x170 net/socket.c:654
 sock_close+0x19/0x30 net/socket.c:1386
 __fput+0x2a3/0x680 fs/file_table.c:384
 ____fput+0x15/0x20 fs/file_table.c:412
 task_work_run+0x116/0x1a0 kernel/task_work.c:179
 resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
 exit_to_user_mode_prepare+0x174/0x180 kernel/entry/common.c:204
 __syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
 syscall_exit_to_user_mode+0x1a/0x30 kernel/entry/common.c:297
 do_syscall_64+0x4b/0x90 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

read to 0xffff8880069af12c of 1 bytes by task 28650 on cpu 0:
 sock_alloc_send_pskb+0xd2/0x620 net/core/sock.c:2767
 unix_dgram_sendmsg+0x2f8/0x14f0 net/unix/af_unix.c:1944
 unix_seqpacket_sendmsg net/unix/af_unix.c:2308 [inline]
 unix_seqpacket_sendmsg+0xba/0x130 net/unix/af_unix.c:2292
 sock_sendmsg_nosec net/socket.c:725 [inline]
 sock_sendmsg+0x148/0x160 net/socket.c:748
 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2494
 ___sys_sendmsg+0xc6/0x140 net/socket.c:2548
 __sys_sendmsg+0x94/0x140 net/socket.c:2577
 __do_sys_sendmsg net/socket.c:2586 [inline]
 __se_sys_sendmsg net/socket.c:2584 [inline]
 __x64_sys_sendmsg+0x45/0x50 net/socket.c:2584
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

value changed: 0x00 -> 0x03

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 28650 Comm: systemd-coredum Not tainted 6.4.0-11989-g68433066 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

unix_tot_inflight is changed under spin_lock(unix_gc_lock), but
unix_release_sock() reads it locklessly.

Let's use READ_ONCE() for unix_tot_inflight.

Note that the writer side was marked by commit 9d6d7f1c ("af_unix:
annote lockless accesses to unix_tot_inflight & gc_in_progress")

BUG: KCSAN: data-race in unix_inflight / unix_release_sock

write (marked) to 0xffffffff871852b8 of 4 bytes by task 123 on cpu 1:
 unix_inflight+0x130/0x180 net/unix/scm.c:64
 unix_attach_fds+0x137/0x1b0 net/unix/scm.c:123
 unix_scm_to_skb net/unix/af_unix.c:1832 [inline]
 unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1955
 sock_sendmsg_nosec net/socket.c:724 [inline]
 sock_sendmsg+0x148/0x160 net/socket.c:747
 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2493
 ___sys_sendmsg+0xc6/0x140 net/socket.c:2547
 __sys_sendmsg+0x94/0x140 net/socket.c:2576
 __do_sys_sendmsg net/socket.c:2585 [inline]
 __se_sys_sendmsg net/socket.c:2583 [inline]
 __x64_sys_sendmsg+0x45/0x50 net/socket.c:2583
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

read to 0xffffffff871852b8 of 4 bytes by task 4891 on cpu 0:
 unix_release_sock+0x608/0x910 net/unix/af_unix.c:671
 unix_release+0x59/0x80 net/unix/af_unix.c:1058
 __sock_release+0x7d/0x170 net/socket.c:653
 sock_close+0x19/0x30 net/socket.c:1385
 __fput+0x179/0x5e0 fs/file_table.c:321
 ____fput+0x15/0x20 fs/file_table.c:349
 task_work_run+0x116/0x1a0 kernel/task_work.c:179
 resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
 exit_to_user_mode_prepare+0x174/0x180 kernel/entry/common.c:204
 __syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
 syscall_exit_to_user_mode+0x1a/0x30 kernel/entry/common.c:297
 do_syscall_64+0x4b/0x90 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x72/0xdc

value changed: 0x00000000 -> 0x00000001

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4891 Comm: systemd-coredum Not tainted 6.4.0-rc5-01219-gfa0e21fa #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

Fixes: 9305cfa4 ("[AF_UNIX]: Make unix_tot_inflight counter non-atomic")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

user->unix_inflight is changed under spin_lock(unix_gc_lock),
but too_many_unix_fds() reads it locklessly.

Let's annotate the write/read accesses to user->unix_inflight.

BUG: KCSAN: data-race in unix_attach_fds / unix_inflight

write to 0xffffffff8546f2d0 of 8 bytes by task 44798 on cpu 1:
 unix_inflight+0x157/0x180 net/unix/scm.c:66
 unix_attach_fds+0x147/0x1e0 net/unix/scm.c:123
 unix_scm_to_skb net/unix/af_unix.c:1827 [inline]
 unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1950
 unix_seqpacket_sendmsg net/unix/af_unix.c:2308 [inline]
 unix_seqpacket_sendmsg+0xba/0x130 net/unix/af_unix.c:2292
 sock_sendmsg_nosec net/socket.c:725 [inline]
 sock_sendmsg+0x148/0x160 net/socket.c:748
 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2494
 ___sys_sendmsg+0xc6/0x140 net/socket.c:2548
 __sys_sendmsg+0x94/0x140 net/socket.c:2577
 __do_sys_sendmsg net/socket.c:2586 [inline]
 __se_sys_sendmsg net/socket.c:2584 [inline]
 __x64_sys_sendmsg+0x45/0x50 net/socket.c:2584
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

read to 0xffffffff8546f2d0 of 8 bytes by task 44814 on cpu 0:
 too_many_unix_fds net/unix/scm.c:101 [inline]
 unix_attach_fds+0x54/0x1e0 net/unix/scm.c:110
 unix_scm_to_skb net/unix/af_unix.c:1827 [inline]
 unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1950
 unix_seqpacket_sendmsg net/unix/af_unix.c:2308 [inline]
 unix_seqpacket_sendmsg+0xba/0x130 net/unix/af_unix.c:2292
 sock_sendmsg_nosec net/socket.c:725 [inline]
 sock_sendmsg+0x148/0x160 net/socket.c:748
 ____sys_sendmsg+0x4e4/0x610 net/socket.c:2494
 ___sys_sendmsg+0xc6/0x140 net/socket.c:2548
 __sys_sendmsg+0x94/0x140 net/socket.c:2577
 __do_sys_sendmsg net/socket.c:2586 [inline]
 __se_sys_sendmsg net/socket.c:2584 [inline]
 __x64_sys_sendmsg+0x45/0x50 net/socket.c:2584
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x6e/0xd8

value changed: 0x000000000000000c -> 0x000000000000000d

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 44814 Comm: systemd-coredum Not tainted 6.4.0-11989-g68433066 #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014

Fixes: 712f4aad ("unix: properly account for FDs passed over unix sockets")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiko Carstens reported that SCM_PIDFD does not work with MSG_CMSG_COMPAT
because scm_pidfd_recv() always checks msg_controllen against sizeof(struct
cmsghdr).

We need to use sizeof(struct compat_cmsghdr) for the compat case.

Fixes: 5e2ff670 ("scm: add SO_PASSPIDFD and SCM_PIDFD")
Reported-by: Heiko Carstens <hca@linux.ibm.com>
Closes: https://lore.kernel.org/netdev/20230901200517.8742-A-hca@linux.ibm.com/Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Tested-by: Heiko Carstens <hca@linux.ibm.com>
Reviewed-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some corporate proxies block our current NIPA URLs because
they use a free / shady DNS domain. As suggested by Jesse
we got a new DNS entry from Konstantin - netdev.bots.linux.dev,
use it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patchwork states are largely self-explanatory but small
ambiguities may still come up. Document how we interpret
the states in networking.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, the defines for phy_device flags in the Micrel driver were
ambiguous in their representation. They were intended to be bit masks
but were mistakenly defined as bit positions. This led to the following
issues:

- MICREL_KSZ8_P1_ERRATA, designated for KSZ88xx switches, overlapped
  with MICREL_PHY_FXEN and MICREL_PHY_50MHZ_CLK.
- Due to this overlap, the code path for MICREL_PHY_FXEN, tailored for
  the KSZ8041 PHY, was not executed for KSZ88xx PHYs.
- Similarly, the code associated with MICREL_PHY_50MHZ_CLK wasn't
  triggered for KSZ88xx.

To rectify this, all three flags have now been explicitly converted to
use the `BIT()` macro, ensuring they are defined as bit masks and
preventing potential overlaps in the future.

Fixes: 49011e0c ("net: phy: micrel: ksz886x/ksz8081: add cabletest support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existing code incorrectly casted a negative value (the result of a
subtraction) to an unsigned value without checking. For example, if
/proc/sys/net/ipv6/conf/*/temp_prefered_lft was set to 1, the preferred
lifetime would jump to 4 billion seconds. On my machine and network the
shortest lifetime that avoided underflow was 3 seconds.

Fixes: 76506a98 ("IPv6: fix DESYNC_FACTOR")
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The veth_xmit function returns NETDEV_TX_OK even when packets are dropped.
This behavior leads to incorrect calculations of statistics counts, as
well as things like txq->trans_start updates.

Fixes: e314dbdc ("[NET]: Virtual ethernet device driver.")
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gve_rx_append_frags() is able to build skbs chained with frag_list,
like GRO engine.

Problem is that shinfo->frag_list should only be used
for the head of the chain.

All other links should use skb->next pointer.

Otherwise, built skbs are not valid and can cause crashes.

Equivalent code in GRO (skb_gro_receive()) is:

    if (NAPI_GRO_CB(p)->last == p)
        skb_shinfo(p)->frag_list = skb;
    else
        NAPI_GRO_CB(p)->last->next = skb;
    NAPI_GRO_CB(p)->last = skb;

Fixes: 9b8dd5e5 ("gve: DQO: Add RX path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Bailey Forrest <bcf@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Catherine Sullivan <csully@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Blamed commit changed:
    ptr = kmalloc(size);
    if (ptr)
      size = ksize(ptr);

to:
    size = kmalloc_size_roundup(size);
    ptr = kmalloc(size);

This allowed various crash as reported by syzbot [1]
and Kyle Zeng.

Problem is that if @size is bigger than 0x80000001,
kmalloc_size_roundup(size) returns 2^32.

kmalloc_reserve() uses a 32bit variable (obj_size),
so 2^32 is truncated to 0.

kmalloc(0) returns ZERO_SIZE_PTR which is not handled by
skb allocations.

Following trace can be triggered if a netdev->mtu is set
close to 0x7fffffff

We might in the future limit netdev->mtu to more sensible
limit (like KMALLOC_MAX_SIZE).

This patch is based on a syzbot report, and also a report
and tentative fix from Kyle Zeng.

[1]
BUG: KASAN: user-memory-access in __build_skb_around net/core/skbuff.c:294 [inline]
BUG: KASAN: user-memory-access in __alloc_skb+0x3c4/0x6e8 net/core/skbuff.c:527
Write of size 32 at addr 00000000fffffd10 by task syz-executor.4/22554

CPU: 1 PID: 22554 Comm: syz-executor.4 Not tainted 6.1.39-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/03/2023
Call trace:
dump_backtrace+0x1c8/0x1f4 arch/arm64/kernel/stacktrace.c:279
show_stack+0x2c/0x3c arch/arm64/kernel/stacktrace.c:286
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x120/0x1a0 lib/dump_stack.c:106
print_report+0xe4/0x4b4 mm/kasan/report.c:398
kasan_report+0x150/0x1ac mm/kasan/report.c:495
kasan_check_range+0x264/0x2a4 mm/kasan/generic.c:189
memset+0x40/0x70 mm/kasan/shadow.c:44
__build_skb_around net/core/skbuff.c:294 [inline]
__alloc_skb+0x3c4/0x6e8 net/core/skbuff.c:527
alloc_skb include/linux/skbuff.h:1316 [inline]
igmpv3_newpack+0x104/0x1088 net/ipv4/igmp.c:359
add_grec+0x81c/0x1124 net/ipv4/igmp.c:534
igmpv3_send_cr net/ipv4/igmp.c:667 [inline]
igmp_ifc_timer_expire+0x1b0/0x1008 net/ipv4/igmp.c:810
call_timer_fn+0x1c0/0x9f0 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x54c/0x710 kernel/time/timer.c:1790
run_timer_softirq+0x28/0x4c kernel/time/timer.c:1803
_stext+0x380/0xfbc
____do_softirq+0x14/0x20 arch/arm64/kernel/irq.c:79
call_on_irq_stack+0x24/0x4c arch/arm64/kernel/entry.S:891
do_softirq_own_stack+0x20/0x2c arch/arm64/kernel/irq.c:84
invoke_softirq kernel/softirq.c:437 [inline]
__irq_exit_rcu+0x1c0/0x4cc kernel/softirq.c:683
irq_exit_rcu+0x14/0x78 kernel/softirq.c:695
el0_interrupt+0x7c/0x2e0 arch/arm64/kernel/entry-common.c:717
__el0_irq_handler_common+0x18/0x24 arch/arm64/kernel/entry-common.c:724
el0t_64_irq_handler+0x10/0x1c arch/arm64/kernel/entry-common.c:729
el0t_64_irq+0x1a0/0x1a4 arch/arm64/kernel/entry.S:584

Fixes: 12d6c1d3 ("skbuff: Proactively round up to kmalloc bucket size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Kyle Zeng <zengyhkyle@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable virtualization features on 82580 just as on i210/i211.
This avoids that virt functions are acidentally called on 82850.

Fixes: 55cac248 ("igb: Add full support for 82580 devices")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When EF10 RXDP firmware is operating in cut-through mode, packet length
 is not known at the time the RX prefix is generated, so it is left as
 zero and RX event merging is inhibited to ensure that the length is
 available in the RX event.  However, it has been found that in certain
 circumstances the RX events for these packets still get merged,
 meaning the driver cannot read the length from the RX event, and tries
 to use the length from the prefix.
The resulting zero-length SKBs cause crashes in GRO since commit
 1d11fa69 ("net-gro: remove GRO_DROP"), so add a check to the driver
 to detect these zero-length RX events and discard the packet.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sriram Yagnaraman says:

====================
Avoid TCP resets when using ECMP for load-balancing between multiple servers.

All packets in the same flow (L3/L4 depending on multipath hash policy)
should be directed to the same target, but after [0]/[1] we see stray
packets directed towards other targets. This, for instance, causes RST
to be sent on TCP connections.

The first two patches solve the problem by ignoring route hints for
destinations that are part of multipath group, by using new SKB flags
for IPv4 and IPv6. The third patch is a selftest that tests the
scenario.

Thanks to Ido, for reviewing and suggesting a way forward in [2] and
also suggesting how to write a selftest for this.

v4->v5:
- Fixed review comments from Ido
v3->v4:
- Remove single path test
- Rebase to latest
v2->v3:
- Add NULL check for skb in fib6_select_path (Ido Schimmel)
- Use fib_tests.sh for selftest instead of the forwarding suite (Ido
  Schimmel)
v1->v2:
- Update to commit messages describing the solution (Ido Schimmel)
- Use perf stat to count fib table lookups in selftest (Ido Schimmel)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The test uses perf stat to count the number of fib:fib_table_lookup
tracepoint hits for IPv4 and the number of fib6:fib6_table_lookup for
IPv6. The measured count is checked to be within 5% of the total number
of packets sent via veth1.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: David S. Miller <davem@davemloft.net>

Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.

A new SKB flag IP6SKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in fib6_select_path() and use it in
ip6_can_use_hint() to check for the existence of the flag.

Fixes: 197dbf24 ("ipv6: introduce and uses route look hints for list input.")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Route hints when the nexthop is part of a multipath group causes packets
in the same receive batch to be sent to the same nexthop irrespective of
the multipath hash of the packet. So, do not extract route hint for
packets whose destination is part of a multipath group.

A new SKB flag IPSKB_MULTIPATH is introduced for this purpose, set the
flag when route is looked up in ip_mkroute_input() and use it in
ip_extract_route_hint() to check for the existence of the flag.

Fixes: 02b24941 ("ipv4: use dst hint for ipv4 list receive")
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bf5c25d6 ("skbuff: in skb_segment, call zerocopy functions
once per nskb") added the call to zero copy functions in skb_segment().
The change introduced a bug in skb_segment() because skb_orphan_frags()
may possibly change the number of fragments or allocate new fragments
altogether leaving nrfrags and frag to point to the old values. This can
cause a panic with stacktrace like the one below.

[  193.894380] BUG: kernel NULL pointer dereference, address: 00000000000000bc
[  193.895273] CPU: 13 PID: 18164 Comm: vh-net-17428 Kdump: loaded Tainted: G           O      5.15.123+ #26
[  193.903919] RIP: 0010:skb_segment+0xb0e/0x12f0
[  194.021892] Call Trace:
[  194.027422]  <TASK>
[  194.072861]  tcp_gso_segment+0x107/0x540
[  194.082031]  inet_gso_segment+0x15c/0x3d0
[  194.090783]  skb_mac_gso_segment+0x9f/0x110
[  194.095016]  __skb_gso_segment+0xc1/0x190
[  194.103131]  netem_enqueue+0x290/0xb10 [sch_netem]
[  194.107071]  dev_qdisc_enqueue+0x16/0x70
[  194.110884]  __dev_queue_xmit+0x63b/0xb30
[  194.121670]  bond_start_xmit+0x159/0x380 [bonding]
[  194.128506]  dev_hard_start_xmit+0xc3/0x1e0
[  194.131787]  __dev_queue_xmit+0x8a0/0xb30
[  194.138225]  macvlan_start_xmit+0x4f/0x100 [macvlan]
[  194.141477]  dev_hard_start_xmit+0xc3/0x1e0
[  194.144622]  sch_direct_xmit+0xe3/0x280
[  194.147748]  __dev_queue_xmit+0x54a/0xb30
[  194.154131]  tap_get_user+0x2a8/0x9c0 [tap]
[  194.157358]  tap_sendmsg+0x52/0x8e0 [tap]
[  194.167049]  handle_tx_zerocopy+0x14e/0x4c0 [vhost_net]
[  194.173631]  handle_tx+0xcd/0xe0 [vhost_net]
[  194.176959]  vhost_worker+0x76/0xb0 [vhost]
[  194.183667]  kthread+0x118/0x140
[  194.190358]  ret_from_fork+0x1f/0x30
[  194.193670]  </TASK>

In this case calling skb_orphan_frags() updated nr_frags leaving nrfrags
local variable in skb_segment() stale. This resulted in the code hitting
i >= nrfrags prematurely and trying to move to next frag_skb using
list_skb pointer, which was NULL, and caused kernel panic. Move the call
to zero copy functions before using frags and nr_frags.

Fixes: bf5c25d6 ("skbuff: in skb_segment, call zerocopy functions once per nskb")
Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com>
Reported-by: Amit Goyal <agoyal@purestorage.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: another round of data-race annotations

Series inspired by some syzbot reports, taking care
of 4 socket fields that can be read locklessly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_bind_phc is read locklessly. Add corresponding annotations.

Fixes: d463126e ("net: sock: extend SO_TIMESTAMPING for PHC binding")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk->sk_tsflags can be read locklessly, add corresponding annotations.

Fixes: b9f40e21 ("net-timestamp: move timestamp flags out of sk_flags")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

msk->rmem_fwd_alloc can be read locklessly.

Add mptcp_rmem_fwd_alloc_add(), similar to sk_forward_alloc_add(),
and appropriate READ_ONCE()/WRITE_ONCE() annotations.

Fixes: 6511882c ("mptcp: allocate fwd memory separately on the rx and tx path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>