Use cmpb which compares each byte in two 64 bit values and
for each matching byte places 0xff in the target and 0x00
otherwise.

A simple hash_name microbenchmark:

http://ozlabs.org/~anton/junkcode/hash_name_bench.c

shows this version to be 10-20% faster than running the x86
version on POWER8, depending on the length.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It is a rarely exercised case, so we want to have a test to ensure it
works as required.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Implement a bi-arch and bi-endian version of load_unaligned_zeropad.

Since the fallback case is so rare, a userspace test harness was used
to test this on ppc64le, ppc64 and ppc32:

http://ozlabs.org/~anton/junkcode/test_load_unaligned_zeropad.c

It uses mprotect to force a SEGV across a page boundary, and a SEGV
handler to lookup the exception tables and run the fixup routine.
It also compares the result against a normal load.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

No need for 3 functions when a single one will do.

Modify the function declaring macros to call the single function.

Reduces object code size a little:

$ size arch/powerpc/platforms/powernv/pci-ioda.o*
   text	   data	    bss	    dec	    hex	filename
  22303	   1073	   6680	  30056	   7568	arch/powerpc/platforms/powernv/pci-ioda.o.new
  22840	   1121	   6776	  30737	   7811	arch/powerpc/platforms/powernv/pci-ioda.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The return value is unnecessary and unused, so make the functions
void instead of int.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When doing vfio passthrough a VF, the kernel will crash with following
message:

[  442.656459] Unable to handle kernel paging request for data at address 0x00000060
[  442.656593] Faulting instruction address: 0xc000000000038b88
[  442.656706] Oops: Kernel access of bad area, sig: 11 [#1]
[  442.656798] SMP NR_CPUS=1024 NUMA PowerNV
[  442.656890] Modules linked in: vfio_pci mlx4_core nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT xt_conntrack bnep bluetooth rfkill ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw tg3 nfsd be2net nfs_acl ses lockd ptp enclosure pps_core kvm_hv kvm_pr shpchp binfmt_misc kvm sunrpc uinput lpfc scsi_transport_fc ipr scsi_tgt [last unloaded: mlx4_core]
[  442.658152] CPU: 40 PID: 14948 Comm: qemu-system-ppc Not tainted 3.10.42yw-pkvm+ #37
[  442.658219] task: c000000f7e2a9a00 ti: c000000f6dc3c000 task.ti: c000000f6dc3c000
[  442.658287] NIP: c000000000038b88 LR: c0000000004435a8 CTR: c000000000455bc0
[  442.658352] REGS: c000000f6dc3f580 TRAP: 0300   Not tainted  (3.10.42yw-pkvm+)
[  442.658419] MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR: 28004882  XER: 20000000
[  442.658577] CFAR: c00000000000908c DAR: 0000000000000060 DSISR: 40000000 SOFTE: 1
GPR00: c0000000004435a8 c000000f6dc3f800 c0000000012b1c10 c00000000da24000
GPR04: 0000000000000003 0000000000001004 00000000000015b3 000000000000ffff
GPR08: c00000000127f5d8 0000000000000000 000000000000ffff 0000000000000000
GPR12: c000000000068078 c00000000fdd6800 000001003c320c80 000001003c3607f0
GPR16: 0000000000000001 00000000105480c8 000000001055aaa8 000001003c31ab18
GPR20: 000001003c10fb40 000001003c360ae8 000000001063bcf0 000000001063bdb0
GPR24: 000001003c15ed70 0000000010548f40 c000001fe5514c88 c000001fe5514cb0
GPR28: c00000000da24000 0000000000000000 c00000000da24000 0000000000000003
[  442.659471] NIP [c000000000038b88] .pcibios_set_pcie_reset_state+0x28/0x130
[  442.659530] LR [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[  442.659585] Call Trace:
[  442.659610] [c000000f6dc3f800] [00000000000719e0] 0x719e0 (unreliable)
[  442.659677] [c000000f6dc3f880] [c0000000004435a8] .pci_set_pcie_reset_state+0x28/0x40
[  442.659757] [c000000f6dc3f900] [c000000000455bf8] .reset_fundamental+0x38/0x80
[  442.659835] [c000000f6dc3f980] [c0000000004562a8] .pci_dev_specific_reset+0xa8/0xf0
[  442.659913] [c000000f6dc3fa00] [c0000000004448c4] .__pci_dev_reset+0x44/0x430
[  442.659980] [c000000f6dc3fab0] [c000000000444d5c] .pci_reset_function+0x7c/0xc0
[  442.660059] [c000000f6dc3fb30] [d00000001c141ab8] .vfio_pci_open+0xe8/0x2b0 [vfio_pci]
[  442.660139] [c000000f6dc3fbd0] [c000000000586c30] .vfio_group_fops_unl_ioctl+0x3a0/0x630
[  442.660219] [c000000f6dc3fc90] [c000000000255fbc] .do_vfs_ioctl+0x4ec/0x7c0
[  442.660286] [c000000f6dc3fd80] [c000000000256364] .SyS_ioctl+0xd4/0xf0
[  442.660354] [c000000f6dc3fe30] [c000000000009e54] syscall_exit+0x0/0x98
[  442.660420] Instruction dump:
[  442.660454] 4bfffce9 4bfffee4 7c0802a6 fbc1fff0 fbe1fff8 f8010010 f821ff81 7c7e1b78
[  442.660566] 7c9f2378 60000000 60000000 e93e02c8 <e8690060> 2fa30000 41de00c4 2b9f0002
[  442.660679] ---[ end trace a64ac9546bcf0328 ]---
[  442.660724]

The reason is current VF is not EEH enabled.

This patch introduces a macro to convert eeh_dev to eeh_pe. By doing so, it
will prevent converting with NULL pointer.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
CC: Michael Ellerman <mpe@ellerman.id.au>

V3 -> V4:
   1. move the macro definition from include/linux/pci.h to
      arch/powerpc/include/asm/eeh.h

V2 -> V3:
   1. rebased on 3.17-rc4
   2. introduce a macro
   3. use this macro in several other places

V1 -> V2:
   1. code style and patch subject adjustment
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We can unindent the bulk of htab_dt_scan_page_sizes() by returning early
if the property is not found. That is nice in and of itself, but also
has the advantage of making it clear that we always return success once
we have found the ibm,segment-page-sizes property.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

"Helps debug funky firmware issues".

After:
  Starting Linux PPC64 #108 SMP Wed Aug 6 19:04:51 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  cpu_features      = 0x17fc7a6c18500249
    possible        = 0x1fffffff18700649
    always          = 0x0000000000000040
  cpu_user_features = 0xdc0065c2 0xee000000
  mmu_features      = 0x5a000001
  firmware_features = 0x00000001405a440b
  htab_hash_mask    = 0x7ffff
  -----------------------------------------------------
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

At boot we display a bunch of low level settings which can be useful to
know, and can help to spot bugs when things are fundamentally
misconfigured.

At the moment they are very widely spaced, so that we can accommodate
the line:

  ppc64_caches.dcache_line_size = 0xYY

But we only print that line when the cache line size is not 128, ie.
almost never, so it just makes the display look odd usually.

The ppc64_caches prefix is redundant so remove it, which means we can
align things a bit closer for the common case. While we're there
replace the last use of camelCase (physicalMemorySize), and use
phys_mem_size.

Before:
  Starting Linux PPC64 #104 SMP Wed Aug 6 18:41:34 EST 2014
  -----------------------------------------------------
  ppc64_pft_size                = 0x1a
  physicalMemorySize            = 0x200000000
  ppc64_caches.dcache_line_size = 0xf0
  ppc64_caches.icache_line_size = 0xf0
  htab_address                  = 0xdeadbeef
  htab_hash_mask                = 0x7ffff
  physical_start                = 0xf000bar
  -----------------------------------------------------

After:
  Starting Linux PPC64 #103 SMP Wed Aug 6 18:38:04 EST 2014
  -----------------------------------------------------
  ppc64_pft_size    = 0x1a
  phys_mem_size     = 0x200000000
  dcache_line_size  = 0xf0
  icache_line_size  = 0xf0
  htab_address      = 0xdeadbeef
  htab_hash_mask    = 0x7ffff
  physical_start    = 0xf000bar
  -----------------------------------------------------

This patch is final, no bike shedding ;)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We are enabling USB unconditionally which results in following build failure

drivers/built-in.o: In function `tb_drom_read':
(.text+0x1b62b70): undefined reference to `usb_speed_string'
make: *** [vmlinux] Error

Enable USB only if USB_SUPPORT is set to avoid such failures
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix the following build failure

drivers/built-in.o: In function `nhi_init':
nhi.c:(.init.text+0x63390): undefined reference to `ehci_init_driver'

by adding a dependency on USB_EHCI_HCD which supplies the ehci_init_driver().

Also we need to depend on USB_OHCI_HCD similarly
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

this patches changes some error handling logics in numa_setup_cpu(),
when cpu node is not found, so:

if the cpu is possible, but not present, -1 is kept in numa_cpu_lookup_table,
so later, if the cpu is added, we could set correct numa information for it.

if the cpu is present, then we set the first online node to
numa_cpu_lookup_table instead of 0 ( in case 0 might not be an online node? )

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().

With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.

For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084.

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With commit 2fabf084 ("powerpc: reorder per-cpu NUMA information's
initialization"), during boottime, cpu_numa_callback() is called
earlier(before their online) for each cpu, and verify_cpu_node_mapping()
uses cpu_to_node() to check whether siblings are in the same node.

It skips the checking for siblings that are not online yet. So the only
check done here is for the bootcpu, which is online at that time. But
the per-cpu numa_node cpu_to_node() uses hasn't been set up yet (which
will be set up in smp_prepare_cpus()).

So I saw something like following reported:
[    0.000000] CPU thread siblings 1/2/3 and 0 don't belong to the same
node!

As we don't actually do the checking during this early stage, so maybe
we could directly call numa_setup_cpu() in do_init_bootmem().

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Acked-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The size field of the op.type word is now the total number of bytes
to be loaded or stored.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This extends the instruction emulation done by analyse_instr() and
emulate_step() to handle a few more instructions that are found in
the kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This splits out the instruction analysis part of emulate_step() into
a separate analyse_instr() function, which decodes the instruction,
but doesn't execute any load or store instructions.  It does execute
integer instructions and branches which can be executed purely by
updating register values in the pt_regs struct.  For other instructions,
it returns the instruction type and other details in a new
instruction_op struct.  emulate_step() then uses that information
to execute loads, stores, cache operations, mfmsr, mtmsr[d], and
(on 64-bit) sc instructions.

The reason for doing this is so that the KVM code can use it instead
of having its own separate instruction emulation code.  Possibly the
alignment interrupt handler could also use this.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In commit e6a6928c "of/fdt: Convert FDT functions to use libfdt",
the kernel stopped supporting old flat device tree formats. The minimum
supported version is now 0x10.

There was a checking function added, early_init_dt_verify(), but it's
not called on powerpc.

The result is, if you boot with an old flat device tree, the kernel will
fail to parse it correctly, think you have no memory etc. and hilarity
ensues.

We can't really fix it, but we can at least catch the fact that the
device tree is in an unsupported format and panic(). We can't call
BUG(), it's too early.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On PowerNV platforms, when a CPU is offline, we put it into nap mode.
It's possible that the CPU wakes up from nap mode while it is still
offline due to a stray IPI.  A misdirected device interrupt could also
potentially cause it to wake up.  In that circumstance, we need to clear
the interrupt so that the CPU can go back to nap mode.

In the past the clearing of the interrupt was accomplished by briefly
enabling interrupts and allowing the normal interrupt handling code
(do_IRQ() etc.) to handle the interrupt.  This has the problem that
this code calls irq_enter() and irq_exit(), which call functions such
as account_system_vtime() which use RCU internally.  Use of RCU is not
permitted on offline CPUs and will trigger errors if RCU checking is
enabled.

To avoid calling into any generic code which might use RCU, we adopt
a different method of clearing interrupts on offline CPUs.  Since we
are on the PowerNV platform, we know that the system interrupt
controller is a XICS being driven directly (i.e. not via hcalls) by
the kernel.  Hence this adds a new icp_native_flush_interrupt()
function to the native-mode XICS driver and arranges to call that
when an offline CPU is woken from nap.  This new function reads the
interrupt from the XICS.  If it is an IPI, it clears the IPI; if it
is a device interrupt, it prints a warning and disables the source.
Then it does the end-of-interrupt processing for the interrupt.

The other thing that briefly enabling interrupts did was to check and
clear the irq_happened flag in this CPU's PACA.  Therefore, after
flushing the interrupt from the XICS, we also clear all bits except
the PACA_IRQ_HARD_DIS (interrupts are hard disabled) bit from the
irq_happened flag.  The PACA_IRQ_HARD_DIS flag is set by power7_nap()
and is left set to indicate that interrupts are hard disabled.  This
means we then have to ignore that flag in power7_nap(), which is
reasonable since it doesn't indicate that any interrupt event needs
servicing.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

I ran some tests to compare hash_64 using shifts and multiplies.
The results:

POWER6:	~2x slower
POWER7: ~2x faster
POWER8: ~2x faster

Now we have a proper config option, select
CONFIG_ARCH_HAS_FAST_MULTIPLIER on POWER7 and POWER8.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This allows the user to build a kernel targeted at POWER8
(ie gcc -mcpu=power8).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When removing a cpu, this patch makes sure that values
gotten from or passed to firmware are in the correct
endian format.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The ibm,ppc-interrupt-server#s property is in big endian format.
These values need to be converted when used by little endian
architectures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id const, too.

While touching these line also put the __init annotation at the right
position where necessary.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

CONFIG_JUMP_LABEL doesn't ensure HAVE_JUMP_LABEL, if it
is not the case use maintainers's own mutex to guard
the modification of global values.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix build error caused by missing export:

ERROR: "dcr_ind_lock" [drivers/net/ethernet/ibm/emac/ibm_emac.ko] undefined!
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

A recent patch added a function prototype for htab_remove_mapping in
c code. Fix it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There were a number of prototypes for functions that no longer
exist. Remove them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Simplify things considerably by moving all the ppc32 specific
symbol exports into its own file.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Move the lib symbol exports closer to their function definitions
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_DUMP_READ token exists before initalising the elog
infrastructure.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 91"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_ELOG_READ token exists before initalising the elog
infrastructure.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 74"
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Check that the OPAL_RTC_READ token exists before we use the OPAL RTC.

Refactors the code a little to merge error paths.

This avoids littering the OPAL console with:
  "OPAL: Called with bad token 3".
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>