- 14 Nov, 2014 39 commits
-
-
Oussama Ghorbel authored
commit f20531a9 upstream. The USB OTG port does not work since v3.16 on omap platform. This is a regression introduced by the commit eb82a3d8 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove). This because the call to pm_runtime_enable() function is moved after the call to devm_phy_create() function, which has side effect since later in the subsequent calls of devm_phy_create() there is a check with pm_runtime_enabled() to configure few things. Fixes: eb82a3d8Signed-off-by:
Oussama Ghorbel <ghorbel@pivasoftware.com> Tested-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
Luis Henriques <luis.henriques@canonical.com>
-
Al Viro authored
commit 7e8631e8 upstream. uninitialized msghdr. Broken in "ocfs2: don't open-code kernel_recvmsg()" by me ;-/ Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Johan Hovold authored
commit 4473d054 upstream. Make sure to only raise DTR on transitions from B0 in set_termios. Also allow set_termios to be called from open with a termios_old of NULL. Note that DTR will not be raised prematurely in this case. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit b598aacc upstream. "raw" is a property of a channel, but should not be part of the name of channel. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit 79fa64eb upstream. We should check if a channel is enabled, not if no channels are enabled. Fixes: 550268ca ("staging:iio: scrap scan_count and ensure all drivers use active_scan_mask") Signed-off-by:
-
Lars-Peter Clausen authored
commit e1055473 upstream. In older versions of the IIO framework it was possible to pass a completely different set of channels to iio_buffer_register() as the one that is assigned to the IIO device. Commit 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") introduced a restriction that requires that the set of channels that is passed to iio_buffer_register() is a subset of the channels assigned to the IIO device as the IIO core will use the list of channels that is assigned to the device to lookup a channel by scan index in iio_compute_scan_bytes(). If it can not find the channel the function will crash. This patch fixes the issue by making sure that the same set of channels is assigned to the IIO device and passed to iio_buffer_register(). Note that we need to remove the IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE info attributes from the channels since we don't actually want those to be registered. Fixes the following crash: Unable to handle kernel NULL pointer dereference at virtual address 00000016 pgd = d2094000 [00000016] *pgd=16e39831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1695 Comm: bash Not tainted 3.17.0-06329-g29461ee #9686 task: d7768040 ti: d5bd4000 task.ti: d5bd4000 PC is at iio_compute_scan_bytes+0x38/0xc0 LR is at iio_compute_scan_bytes+0x34/0xc0 pc : [<c0316de8>] lr : [<c0316de4>] psr: 60070013 sp : d5bd5ec0 ip : 00000000 fp : 00000000 r10: d769f934 r9 : 00000000 r8 : 00000001 r7 : 00000000 r6 : c8fc6240 r5 : d769f800 r4 : 00000000 r3 : d769f800 r2 : 00000000 r1 : ffffffff r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 18c5387d Table: 1209404a DAC: 00000015 Process bash (pid: 1695, stack limit = 0xd5bd4240) Stack: (0xd5bd5ec0 to 0xd5bd6000) 5ec0: d769f800 d7435640 c8fc6240 d769f984 00000000 c03175a4 d7435690 d7435640 5ee0: d769f990 00000002 00000000 d769f800 d5bd4000 00000000 000b43a8 c03177f4 5f00: d769f810 0162b8c8 00000002 c8fc7e00 d77f1d08 d77f1da8 c8fc7e00 c01faf1c 5f20: 00000002 c010694c c010690c d5bd5f88 00000002 c8fc6840 c8fc684c c0105e08 5f40: 00000000 00000000 d20d1580 00000002 000af408 d5bd5f88 c000de84 c00b76d4 5f60: d20d1580 000af408 00000002 d20d1580 d20d1580 00000002 000af408 c000de84 5f80: 00000000 c00b7a44 00000000 00000000 00000002 b6ebea78 00000002 000af408 5fa0: 00000004 c000dd00 b6ebea78 00000002 00000001 000af408 00000002 00000000 5fc0: b6ebea78 00000002 000af408 00000004 bee96a4c 000a6094 00000000 000b43a8 5fe0: 00000000 bee969cc b6e2eb77 b6e6525c 40070010 00000001 00000000 00000000 [<c0316de8>] (iio_compute_scan_bytes) from [<c03175a4>] (__iio_update_buffers+0x248/0x438) [<c03175a4>] (__iio_update_buffers) from [<c03177f4>] (iio_buffer_store_enable+0x60/0x7c) [<c03177f4>] (iio_buffer_store_enable) from [<c01faf1c>] (dev_attr_store+0x18/0x24) [<c01faf1c>] (dev_attr_store) from [<c010694c>] (sysfs_kf_write+0x40/0x4c) [<c010694c>] (sysfs_kf_write) from [<c0105e08>] (kernfs_fop_write+0x110/0x154) [<c0105e08>] (kernfs_fop_write) from [<c00b76d4>] (vfs_write+0xbc/0x170) [<c00b76d4>] (vfs_write) from [<c00b7a44>] (SyS_write+0x40/0x78) [<c00b7a44>] (SyS_write) from [<c000dd00>] (ret_fast_syscall+0x0/0x30) Fixes: 959d2952 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by:
-
George McCollister authored
commit f73cde60 upstream. Signed-off-by:
George McCollister <george.mccollister@gmail.com> Acked-by:
Hartmut Knaack <knaack.h@gmx.de> Signed-off-by:
-
Takashi Iwai authored
commit 0725dda2 upstream. Some USB-audio devices show weird sysfs warnings at disconnecting the devices, e.g. usb 1-3: USB disconnect, device number 3 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 973 at fs/sysfs/group.c:216 device_del+0x39/0x180() sysfs group ffffffff8183df40 not found for kobject 'midiC1D0' Call Trace: [<ffffffff814a3e38>] ? dump_stack+0x49/0x71 [<ffffffff8103cb72>] ? warn_slowpath_common+0x82/0xb0 [<ffffffff8103cc55>] ? warn_slowpath_fmt+0x45/0x50 [<ffffffff813521e9>] ? device_del+0x39/0x180 [<ffffffff81352339>] ? device_unregister+0x9/0x20 [<ffffffff81352384>] ? device_destroy+0x34/0x40 [<ffffffffa00ba29f>] ? snd_unregister_device+0x7f/0xd0 [snd] [<ffffffffa025124e>] ? snd_rawmidi_dev_disconnect+0xce/0x100 [snd_rawmidi] [<ffffffffa00c0192>] ? snd_device_disconnect+0x62/0x90 [snd] [<ffffffffa00c025c>] ? snd_device_disconnect_all+0x3c/0x60 [snd] [<ffffffffa00bb574>] ? snd_card_disconnect+0x124/0x1a0 [snd] [<ffffffffa02e54e8>] ? usb_audio_disconnect+0x88/0x1c0 [snd_usb_audio] [<ffffffffa015260e>] ? usb_unbind_interface+0x5e/0x1b0 [usbcore] [<ffffffff813553e9>] ? __device_release_driver+0x79/0xf0 [<ffffffff81355485>] ? device_release_driver+0x25/0x40 [<ffffffff81354e11>] ? bus_remove_device+0xf1/0x130 [<ffffffff813522b9>] ? device_del+0x109/0x180 [<ffffffffa01501d5>] ? usb_disable_device+0x95/0x1f0 [usbcore] [<ffffffffa014634f>] ? usb_disconnect+0x8f/0x190 [usbcore] [<ffffffffa0149179>] ? hub_thread+0x539/0x13a0 [usbcore] [<ffffffff810669f5>] ? sched_clock_local+0x15/0x80 [<ffffffff81066c98>] ? sched_clock_cpu+0xb8/0xd0 [<ffffffff81070730>] ? bit_waitqueue+0xb0/0xb0 [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffff8105973e>] ? kthread+0xce/0xf0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 [<ffffffff814a8b7c>] ? ret_from_fork+0x7c/0xb0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 ---[ end trace 40b1928d1136b91e ]--- This comes from the fact that usb-audio driver may receive the disconnect callback multiple times, per each usb interface. When a device has both audio and midi interfaces, it gets called twice, and currently the driver tries to release resources at the last call. At this point, the first parent interface has been already deleted, thus deleting a child of the first parent hits such a warning. For fixing this problem, we need to call snd_card_disconnect() and cancel pending operations at the very first disconnect while the release of the whole objects waits until the last disconnect call. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931Reported-and-tested-by:
Tomas Gayoso <tgayoso@gmail.com> Reported-and-tested-by:
Chris J Arges <chris.j.arges@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Chris Mason authored
commit 6e5aafb2 upstream. If we hit any errors in btrfs_lookup_csums_range, we'll loop through all the csums we allocate and free them. But the code was using list_entry incorrectly, and ended up trying to free the on-stack list_head instead. This bug came from commit 0678b618 btrfs: Don't BUG_ON kzalloc error in btrfs_lookup_csums_range() Signed-off-by:
Chris Mason <clm@fb.com> Reported-by:
Erik Berg <btrfs@slipsprogrammoer.no> Signed-off-by:
-
Alexander Stein authored
commit 5cc7b047 upstream. There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the lower 2 bits of the chip select to select a CTAR register. SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values if the chip selects 4/5 are used. For those chip selects SPI_CTAR even calculated offsets of non-existing registers. Signed-off-by:
Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Grant Likely authored
commit a87fa1d8 upstream. The string property read helpers will run off the end of the buffer if it is handed a malformed string property. Rework the parsers to make sure that doesn't happen. At the same time add new test cases to make sure the functions behave themselves. The original implementations of of_property_read_string_index() and of_property_count_strings() both open-coded the same block of parsing code, each with it's own subtly different bugs. The fix here merges functions into a single helper and makes the original functions static inline wrappers around the helper. One non-bugfix aspect of this patch is the addition of a new wrapper, of_property_read_string_array(). The new wrapper is needed by the device_properties feature that Rafael is working on and planning to merge for v3.19. The implementation is identical both with and without the new static inline wrapper, so it just got left in to reduce the churn on the header file. Signed-off-by:
Grant Likely <grant.likely@linaro.org> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darren Hart <darren.hart@intel.com> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Hans de Goede authored
commit d1d95482 upstream. These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Oliver Neukum authored
commit b45abacd upstream. The switch back is limited to ULT even on HP. The contrary finding arose by bad luck in BIOS versions for testing. This fixes spontaneous resume from S3 on some HP laptops. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Adel Gadllah authored
commit d7499475 upstream. Yet another device affected by this. Tested-by:
Kevin Fenzi <kevin@scrye.com> Signed-off-by:
Adel Gadllah <adel.gadllah@gmail.com> Signed-off-by:
-
Adel Gadllah authored
commit 876af5d4 upstream. Currently this quirk is enabled for the model with the device id 0x0089, it is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904 as well. Signed-off-by:
-
Johan Hovold authored
commit c68929f7 upstream. Enable device-qualifier quirk for Elan Touchscreen, which often fails to handle requests for the device_descriptor. Note that the device sometimes do respond properly with a Request Error (three times as USB core retries), but usually fails to respond at all. When this happens any further descriptor requests also fails, for example: [ 1528.688934] usb 2-7: new full-speed USB device number 4 using xhci_hcd [ 1530.945588] usb 2-7: unable to read config index 0 descriptor/start: -71 [ 1530.945592] usb 2-7: can't read configurations, error -71 This has been observed repeating for over a minute before eventual successful enumeration. Reported-by:
Drew Von Spreecken <drewvs@gmail.com> Reported-by:
-
Johan Hovold authored
commit 2a159389 upstream. Add new quirk for devices that cannot handle requests for the device_qualifier descriptor. A USB-2.0 compliant device must respond to requests for the device_qualifier descriptor (even if it's with a request error), but at least one device is known to misbehave after such a request. Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Hans de Goede authored
commit 673029fe upstream. Just like some Seagate enclosures, these devices do not seem to grok ata pass through commands. Signed-off-by:
-
Hans de Goede authored
commit 2391eacb upstream. Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk which is known to work fine with other controllers causes the system to freeze when connected over usb-3 with this controller, where as it works fine with uas in usb-2 ports, indicating a problem with streams. This is a bit bigger hammer then I would like to use for this, but for now it will have to make do. I've ordered a pci-e usb controller card with an Asmedia 1042, once that arrives I'll try to get streams to work (with a quirk flag if necessary) and then we can re-enable them. For now this at least makes uas capable disk enclosures work again by forcing fallback to the usb-storage driver. Reported-by:
Bogdan Mihalcea <bogdan.mihalcea@infim.ro> Cc: Bogdan Mihalcea <bogdan.mihalcea@infim.ro> Signed-off-by:
-
Hans de Goede authored
commit aee0ce3a upstream. These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Signed-off-by:
-
Alan Stern authored
commit 93c9bf4d upstream. Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by:
Paul Osmialowski <newchief@king.net.pl> Signed-off-by:
-
Hans de Goede authored
commit 90a646c7 upstream. This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140 <snip> [10251.059473] Call Trace: [10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0 [10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0 [10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0 [10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110 [10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270 <snip> The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Signed-off-by:
-
Johan Hovold authored
commit cf84a691 upstream. Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by:
Karl Palsson <karlp@tweak.net.au> Signed-off-by:
-
Krzysztof Kozlowski authored
commit ca0c37a0 upstream. Driver allocated on stack struct regulator_config but didn't initialize it fully. Few fields (driver_data, ena_gpio) were left untouched. This lead to using random ena_gpio values as GPIOs for max77693 regulators. On occasion these values could match real GPIO numbers leading to interfering with other drivers and to unsuccessful enable/disable of regulator. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Fixes: 80b022e2 ("regulator: max77693: Add max77693 regualtor driver.") Signed-off-by:
-
Johan Hovold authored
commit e681286d upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51 ("USB: opticon: Add Opticon OPN2001 write support") Signed-off-by:
-
Johan Hovold authored
commit 19125283 upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Grzegorz Jaszczyk authored
commit 758e8366 upstream. In both Armada-375 and Armada-38x MPIC interrupts should be identified by reading cause register multiplied by the interrupt mask. A lack of above mentioned multiplication resulted in a bug, caused by the fact that in Armada-375 and Armada-38x some of the interrupts (e.g. network interrupts) can be handled either as a GIC or MPIC interrupts. Therefore during MPIC interrupts handling, cause register shows hits from interrupts even if they are masked for MPIC but unmasked for a GIC. This resulted in 'bad IRQ' error, because masked MPIC interrupt without registered interrupt handler, was trying to be handled during interrupt handling procedure of some other unmasked MPIC interrupt (e.g. local timer irq). This commit fixes that by ensuring that during MPIC interrupt handling only interrupts that are unmasked for MPIC are processed. Signed-off-by:
Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Fixes: bc69b8ad ("irqchip: armada-370-xp: Setup a chained handler for the MPIC") Acked-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Link: https://lkml.kernel.org/r/1411643839-64925-3-git-send-email-jaz@semihalf.comSigned-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
-
Grzegorz Jaszczyk authored
commit 298dcb2d upstream. The MSI interrupts use the 16 high doorbells, which are notified by using IRQ1 of the main interrupt controller. The MSI interrupts were handled correctly for Armada-XP and Armada-370 but not for Armada-375 and Armada-38x, which use chained handler for the MPIC. This commit fixes that by checking proper interrupt number in chained handler for the MPIC. Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 325e4114 upstream. Endian is hard, especially when I designed a stupid FW interface, and I should know better... oh well, this is attempt #2 at fixing this properly. This time it seems to work with all access sizes and I can run my flashing tool (which exercises all sort of access sizes and types to access the SPI controller in the BMC) just fine. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anton Blanchard authored
commit 808be314 upstream. Back in 7230c564 ("powerpc: Rework lazy-interrupt handling") we added a call out to restore_interrupts() (written in c) before calling do_notify_resume: bl restore_interrupts addi r3,r1,STACK_FRAME_OVERHEAD bl do_notify_resume Unfortunately do_notify_resume takes two arguments, the second one being the thread_info flags: void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags) We do populate r4 (the second argument) earlier, but restore_interrupts() is free to muck it up all it wants. My guess is the gcc compiler gods shone down on us and its register allocator never used r4. Sometimes, rarely, luck is on our side. LLVM on the other hand did trample r4. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Ulrich Eckhardt authored
commit 8c5bcded upstream. The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not automatically power down. This blocks other receivers connected to a satellite channel router (EN50494), since the receivers can not send the required DiSEqC sequences when the Tevii card is connected to a the same SCR. This patch switches off the LNB supply voltage on initialization of the frontend. [mchehab@osg.samsung.com: add a comment about why we're explicitly turning off voltage at device init] Signed-off-by:
Ulrich Eckhardt <uli@uli-eckhardt.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Jan Kara authored
commit a8d42056 upstream. When we fail to allocate page vector in rbd_obj_read_sync() we just basically ignore the problem and continue which will result in an oops later. Fix the problem by returning proper error. CC: Yehuda Sadeh <yehuda@inktank.com> CC: Sage Weil <sage@inktank.com> CC: ceph-devel@vger.kernel.org Coverity-id: 1226882 Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Ilya Dryomov <idryomov@redhat.com> Signed-off-by:
-
Lukas Bossard authored
commit 7c21539c upstream. Adding ultra doch support for Lenovo Thinkpad X240 (17aa:2214). [Actually replaced the entry with ALC292_FIXUP_TPT440_DOCK -- tiwai] Signed-off-by:
Lukas Bossard <mr.bobukas@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 6d16941a upstream. There is another Thinkpad T440 with SSID 17aa:2212 that has a dock port. Reported-by:
Siwei Luo <sluo@smartbeans.de> Signed-off-by:
-
David Cohen authored
commit d90c3381 upstream. Even if a gpio pin is set to output, we still need to set INPUT_EN functionality (by clearing INPUT_EN bit) to be able to read the pin's level. E.g. without this change, we'll always read low level state from sysfs. Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
David Cohen <david.a.cohen@linux.intel.com> Reviewed-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by:
-
Hans de Goede authored
commit 183fd8fc upstream. The acpi-video backlight interface on the Acer KAV80 is broken, and worse it causes the entire machine to slow down significantly after a suspend/resume. Blacklist it, and use the acer-wmi backlight interface instead. Note that the KAV80 is somewhat unique in that it is the only Acer model where we fall back to acer-wmi after blacklisting, rather then using the native (e.g. intel) backlight driver. This is done because there is no native backlight interface on this model. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
-
Hans de Goede authored
commit 5a1426c9 upstream. The acpi-video backlight interface on the NC210 does not work, blacklist it and use the samsung-laptop interface instead. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=861573Signed-off-by:
-
Luis Henriques authored
Signed-off-by: -
Cong Wang authored
commit 21e81002 upstream. I saw the following kernel warning: [ 1852.321222] ------------[ cut here ]------------ [ 1852.326527] WARNING: CPU: 0 PID: 118 at fs/proc/generic.c:521 remove_proc_entry+0x154/0x16b() [ 1852.335630] remove_proc_entry: removing non-empty directory 'fs/nfsfs', leaking at least 'volumes' [ 1852.344084] CPU: 0 PID: 118 Comm: kworker/u8:2 Not tainted 3.16.0+ #540 [ 1852.350036] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 1852.354992] Workqueue: netns cleanup_net [ 1852.358701] 0000000000000000 ffff880116f2fbd0 ffffffff819c03e9 ffff880116f2fc18 [ 1852.366474] ffff880116f2fc08 ffffffff810744ee ffffffff811e0e6e ffff8800d4e96238 [ 1852.373507] ffffffff81dbe665 ffff8800d46a5948 0000000000000005 ffff880116f2fc68 [ 1852.380224] Call Trace: [ 1852.381976] [<ffffffff819c03e9>] dump_stack+0x4d/0x66 [ 1852.385495] [<ffffffff810744ee>] warn_slowpath_common+0x7a/0x93 [ 1852.389869] [<ffffffff811e0e6e>] ? remove_proc_entry+0x154/0x16b [ 1852.393987] [<ffffffff8107457b>] warn_slowpath_fmt+0x4c/0x4e [ 1852.397999] [<ffffffff811e0e6e>] remove_proc_entry+0x154/0x16b [ 1852.402034] [<ffffffff8129c73d>] nfs_fs_proc_net_exit+0x53/0x56 [ 1852.406136] [<ffffffff812a103b>] nfs_net_exit+0x12/0x1d [ 1852.409774] [<ffffffff81785bc9>] ops_exit_list+0x44/0x55 [ 1852.413529] [<ffffffff81786389>] cleanup_net+0xee/0x182 [ 1852.417198] [<ffffffff81088c9e>] process_one_work+0x209/0x40d [ 1852.502320] [<ffffffff81088bf7>] ? process_one_work+0x162/0x40d [ 1852.587629] [<ffffffff810890c1>] worker_thread+0x1f0/0x2c7 [ 1852.673291] [<ffffffff81088ed1>] ? process_scheduled_works+0x2f/0x2f [ 1852.759470] [<ffffffff8108e079>] kthread+0xc9/0xd1 [ 1852.843099] [<ffffffff8109427f>] ? finish_task_switch+0x3a/0xce [ 1852.926518] [<ffffffff8108dfb0>] ? __kthread_parkme+0x61/0x61 [ 1853.008565] [<ffffffff819cbeac>] ret_from_fork+0x7c/0xb0 [ 1853.076477] [<ffffffff8108dfb0>] ? __kthread_parkme+0x61/0x61 [ 1853.140653] ---[ end trace 69c4c6617f78e32d ]--- It looks wrong that we add "/proc/net/nfsfs" in nfs_fs_proc_net_init() while remove "/proc/fs/nfsfs" in nfs_fs_proc_net_exit(). Fixes: commit 65b38851 (NFS: Fix /proc/fs/nfsfs/servers and /proc/fs/nfsfs/volumes) Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Cc: Dan Aloni <dan@kernelim.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> [Trond: replace uses of remove_proc_entry() with remove_proc_subtree() as suggested by Al Viro] Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
- 13 Nov, 2014 1 commit
-
-
Jan Kara authored
commit f55fefd1 upstream. The WARN_ON checking whether i_mutex is held in pagecache_isize_extended() was wrong because some filesystems (e.g. XFS) use different locks for serialization of truncates / writes. So just remove the check. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
