- 15 Jan, 2017 2 commits
-
-
David Ahern authored
[ Upstream commit eb63ecc1 ] Locally originated traffic in a VRF fails in the presence of a POSTROUTING rule. For example, $ iptables -t nat -A POSTROUTING -s 11.1.1.0/24 -j MASQUERADE $ ping -I red -c1 11.1.1.3 ping: Warning: source address might be selected on device other than red. PING 11.1.1.3 (11.1.1.3) from 11.1.1.2 red: 56(84) bytes of data. ping: sendmsg: Operation not permitted Worse, the above causes random corruption resulting in a panic in random places (I have not seen a consistent backtrace). Call nf_reset to drop the conntrack info following the pass through the VRF device. The nf_reset is needed on Tx but not Rx because of the order in which NF_HOOK's are hit: on Rx the VRF device is after the real ingress device and on Tx it is is before the real egress device. Connection tracking should be tied to the real egress device and not the VRF device. Fixes: 8f58336d ("net: Add ethernet header for pass through VRF device") Fixes: 35402e31 ("net: Add IPv6 support to VRF device") Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
David Ahern authored
[ Upstream commit a0f37efa ] Connection tracking with VRF is broken because the pass through the VRF device drops the connection tracking info. Removing the call to nf_reset allows DNAT and MASQUERADE to work across interfaces within a VRF. Fixes: 73e20b76 ("net: vrf: Add support for PREROUTING rules on vrf device") Signed-off-by:
-
- 12 Jan, 2017 38 commits
-
-
Greg Kroah-Hartman authored
-
Felipe Balbi authored
commit eaa496ff upstream. ep->mult is supposed to be set to Isochronous and Interrupt Endapoint's multiplier value. This value is computed from different places depending on the link speed. If we're dealing with HighSpeed, then it's part of bits [12:11] of wMaxPacketSize. This case wasn't taken into consideration before. While at that, also make sure the ep->mult defaults to one so drivers can use it unconditionally and assume they'll never multiply ep->maxpacket to zero. Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit eab1c4e2 which is commit eaa496ff upstream as it was incorrectly backported. Reported-by:
Bin Liu <b-liu@ti.com> Cc: Felipe Balbi <balbi@kernel.org> Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit 98068574, which is commit ba9f93f8 upstream as it causes problems. Reported-by:
Dmitry Osipenko <digetx@gmail.com> Cc: Ping-Ke Shih <pkshih@realtek.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
-
Thomas Gleixner authored
commit c1a9eeb9 upstream. When a disfunctional timer, e.g. dummy timer, is installed, the tick core tries to setup the broadcast timer. If no broadcast device is installed, the kernel crashes with a NULL pointer dereference in tick_broadcast_setup_oneshot() because the function has no sanity check. Reported-by:
Mason <slash.tmp@free.fr> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Richard Cochran <rcochran@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org>, Cc: Sebastian Frias <sf84@laposte.net> Cc: Thibaud Cornic <thibaud_cornic@sigmadesigns.com> Cc: Robin Murphy <robin.murphy@arm.com> Link: http://lkml.kernel.org/r/1147ef90-7877-e4d2-bb2b-5c4fa8d3144b@free.frSigned-off-by:
-
Thomas Gleixner authored
commit 9bf11ecc upstream. When the dummy timer callback is invoked before the real timer callbacks, then it tries to install that timer for the starting CPU. If the platform does not have a broadcast timer installed the installation fails with a kernel crash. The crash happens due to a unconditional deference of the non available broadcast device. This needs to be fixed in the timer core code. But even when this is fixed in the core code then installing the dummy timer before the real timers is a pointless exercise. Move it to the end of the callback list. Fixes: 00c1d17a ("clocksource/dummy_timer: Convert to hotplug state machine") Reported-and-tested-by:
-
Carlos Maiolino authored
commit ff97f239 upstream. max_retries _show and _store functions should test against cfg->max_retries, not cfg->retry_timeout Signed-off-by:
Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by:
Eric Sandeen <sandeen@redhat.com> Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
commit a1b7a4de upstream. There is a race window between write_cache_pages calling clear_page_dirty_for_io and XFS calling set_page_writeback, in which the mapping for an inode is tagged neither as dirty, nor as writeback. If the COW shrinker hits in exactly that window we'll remove the delayed COW extents and writepages trying to write it back, which in release kernels will manifest as corruption of the bmap btree, and in debug kernels will trip the ASSERT about now calling xfs_bmapi_write with the COWFORK flag for holes. A complex customer load manages to hit this window fairly reliably, probably by always having COW writeback in flight while the cow shrinker runs. This patch adds another check for having the I_DIRTY_PAGES flag set, which is still set during this race window. While this fixes the problem I'm still not overly happy about the way the COW shrinker works as it still seems a bit fragile. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Darrick J. Wong authored
commit 20e73b00 upstream. We need to use the actual AG length when making per-AG reservations, since we could otherwise end up reserving more blocks out of the last AG than there are actual blocks. Complained-about-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
-
Darrick J. Wong authored
commit 7a21272b upstream. Dan Carpenter reported a double-free of rcur if _defer_finish fails while we're recovering CUI items. Fix the error recovery to prevent this. Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Darrick J. Wong authored
commit b24a978c upstream. Use NOFS for allocating btree cursors, since they can be called under the ilock. Signed-off-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Eric Sandeen authored
commit 2e1d2337 upstream. When we create a new attribute, we first create a shortform attribute, and try to fit the new attribute into it. If that fails, we copy the (empty) attribute into a leaf attribute, and do the copy again. Thus there can be a transient state where we have an empty leaf attribute. If we encounter this during log replay, the verifier will fail. So add a test to ignore this part of the leaf attr verification during log replay. Thanks as usual to dchinner for spotting the problem. Signed-off-by:
-
Darrick J. Wong authored
commit 1bb33a98 upstream. After various discussions on linux-fsdevel, it has been decided that it is not necessary to cap the length of a dedupe request, and that correctly-written userspace client programs will be able to absorb the change. Therefore, remove the length clamping behavior. Signed-off-by:
-
Darrick J. Wong authored
commit ef388e20 upstream. The on-disk field di_size is used to set i_size, which is a signed integer of loff_t. If the high bit of di_size is set, we'll end up with a negative i_size, which will cause all sorts of problems. Since the VFS won't let us create a file with such length, we should catch them here in the verifier too. Signed-off-by:
-
Darrick J. Wong authored
commit 0f352f8e upstream. We shouldn't assert if somehow we end up trying to add an attr fork to an inode that apparently already has attr extents because this is an indication of on-disk corruption. Instead, return an error code to userspace. Signed-off-by:
-
Darrick J. Wong authored
commit 96a3aefb upstream. In xfs_dir3_data_read, we can encounter the situation where err == 0 and *bpp == NULL if the given bno offset happens to be a hole; this leads to a crash if we try to set the buffer type after the _da_read_buf call. Holes can happen due to corrupt or malicious entries in the bmbt data, so be a little more careful when we're handling buffers. Signed-off-by:
-
Darrick J. Wong authored
commit 356a3225 upstream. When reading into memory all extents of a btree-format inode fork, complain if the number of extents we find is not the same as the number of extents reported in the inode core. This is needed to stop an IO action from accessing the garbage areas of the in-core fork. [dchinner: removed redundant assert] Signed-off-by:
-
Darrick J. Wong authored
commit bb3be7e7 upstream. When we're reading a btree block, make sure that what we retrieved matches the owner and level; and has a plausible number of records. Signed-off-by:
-
Darrick J. Wong authored
commit d2a047f3 upstream. There is no such thing as a zero-level AG btree since even a single-node zero-records btree has one level. Btree cursor constructors read cur_nlevels straight from disk and then access things like cur_bufs[cur_nlevels - 1] which is /really/ bad if cur_nlevels is zero! Therefore, strengthen the verifiers to prevent this possibility. Signed-off-by:
-
Eric Sandeen authored
commit c44a1f22 upstream. By inspection, xfs_bmap_trace_exlist isn't handling cow forks, and will trace the data fork instead. Fix this by setting state appropriately if whichfork == XFS_COW_FORK. ()___() < @ @ > | | {o_o} (|) Signed-off-by:
-
Eric Sandeen authored
commit 7710517f upstream. When xfs_bmap_trace_exlist called trace_xfs_extlist, it sent in the "whichfork" var instead of the bmap "state" as expected (even though state was already set up for this purpose). As a result, the xfs_bmap_class in tracing code used "whichfork" not state in xfs_iext_state_to_fork(), and got the wrong ifork pointer. It all goes downhill from there, including an ASSERT when ifp_bytes is empty by the time it reaches xfs_iext_get_ext(): XFS: Assertion failed: idx < ifp->if_bytes / sizeof(xfs_bmbt_rec_t) Signed-off-by:
-
Eric Sandeen authored
commit 200237d6 upstream. We've missed properly setting the buffer type for an AGI transaction in 3 spots now, so just move it into xfs_read_agi() and set it if we are in a transaction to avoid the problem in the future. This is similar to how it is done in i.e. the dir3 and attr3 read functions. Signed-off-by:
-
Brian Foster authored
commit f782088c upstream. xfs_file_iomap_begin_delay() implements post-eof speculative preallocation by extending the block count of the requested delayed allocation. Now that xfs_bmapi_reserve_delalloc() has been updated to handle prealloc blocks separately and tag the inode, update xfs_file_iomap_begin_delay() to use the new parameter and rely on the former to tag the inode. Note that this patch does not change behavior. Signed-off-by:
-
Christoph Hellwig authored
commit 656152e5 upstream. And only lookup the previous extent inside xfs_iomap_prealloc_size if we actually need it. Signed-off-by:
-
Brian Foster authored
commit 0260d8ff upstream. COW fork reservation is implemented via delayed allocation. The code is modeled after the traditional delalloc allocation code, but is slightly different in terms of how preallocation occurs. Rather than post-eof speculative preallocation, COW fork preallocation is implemented via a COW extent size hint that is designed to minimize fragmentation as a reflinked file is split over time. xfs_reflink_reserve_cow() still uses logic that is oriented towards dealing with post-eof speculative preallocation, however, and is stale or not necessarily correct. First, the EOF alignment to the COW extent size hint is implemented in xfs_bmapi_reserve_delalloc() (which does so correctly by aligning the start and end offsets) and so is not necessary in xfs_reflink_reserve_cow(). The backoff and retry logic on ENOSPC is also ineffective for the same reason, as xfs_bmapi_reserve_delalloc() will simply perform the same allocation request on the retry. Finally, since the COW extent size hint aligns the start and end offset of the range to allocate, the end_fsb != orig_end_fsb logic is not sufficient. Indeed, if a write request happens to end on an aligned offset, it is possible that we do not tag the inode for COW preallocation even though xfs_bmapi_reserve_delalloc() may have preallocated at the start offset. Kill the unnecessary, duplicate code in xfs_reflink_reserve_cow(). Remove the inode tag logic as well since xfs_bmapi_reserve_delalloc() has been updated to tag the inode correctly. Signed-off-by:
-
Christoph Hellwig authored
commit 2755fc44 upstream. Signed-off-by:
-
Brian Foster authored
commit 974ae922 upstream. Speculative preallocation is currently processed entirely by the callers of xfs_bmapi_reserve_delalloc(). The caller determines how much preallocation to include, adjusts the extent length and passes down the resulting request. While this works fine for post-eof speculative preallocation, it is not as reliable for COW fork preallocation. COW fork preallocation is implemented via the cowextszhint, which aligns the start offset as well as the length of the extent. Further, it is difficult for the caller to accurately identify when preallocation occurs because the returned extent could have been merged with neighboring extents in the fork. To simplify this situation and facilitate further COW fork preallocation enhancements, update xfs_bmapi_reserve_delalloc() to take a separate preallocation parameter to incorporate into the allocation request. The preallocation blocks value is tacked onto the end of the request and adjusted to accommodate neighboring extents and extent size limits. Since xfs_bmapi_reserve_delalloc() now knows precisely how much preallocation was included in the allocation, it can also tag the inodes appropriately to support preallocation reclaim. Note that xfs_bmapi_reserve_delalloc() callers are not yet updated to use the preallocation mechanism. This patch should not change behavior outside of correctly tagging reflink inodes when start offset preallocation occurs (which the caller does not handle correctly). Signed-off-by:
-
Christoph Hellwig authored
commit 65c5f419 upstream. We can easily lookup the previous extent for the cases where we need it, which saves the callers from looking it up for us later in the series. Signed-off-by:
-
Darrick J. Wong authored
commit fba3e594 upstream. It turns out that btrfs and xfs had differing interpretations of what to do when the dedupe length is zero. Change xfs to follow btrfs' semantics so that the userland interface is consistent. Signed-off-by:
-
Darrick J. Wong authored
commit fd26a880 upstream. When we're estimating the amount of space it's going to take to satisfy a delalloc reservation, we need to include the space that we might need to grow the rmapbt. This helps us to avoid running out of space later when _iomap_write_allocate needs more space than we reserved. Eryu Guan observed this happening on generic/224 when sunit/swidth were set. Reported-by:
Eryu Guan <eguan@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
commit 93533c78 upstream. xfs_iext_lookup_extent looks up a single extent at the passed in offset, and returns the extent covering the area, or the one behind it in case of a hole, as well as the index of the returned extent in arguments, as well as a simple bool as return value that is set to false if no extent could be found because the offset is behind EOF. It is a simpler replacement for xfs_bmap_search_extent that leaves looking up the rarely needed previous extent to the caller and has a nicer calling convention. xfs_iext_get_extent is a helper for iterating over the extent list, it takes an extent index as input, and returns the extent at that index in it's expanded form in an argument if it exists. The actual return value is a bool whether the index is valid or not. Signed-off-by:
-
Brian Foster authored
commit 98efe8af upstream. Filesystem shutdown testing on an older distro kernel has uncovered an imbalanced locking pattern for the inode flush lock in xfs_reclaim_inode(). Specifically, there is a double unlock sequence between the call to xfs_iflush_abort() and xfs_reclaim_inode() at the "reclaim:" label. This actually does not cause obvious problems on current kernels due to the current flush lock implementation. Older kernels use a counting based flush lock mechanism, however, which effectively breaks the lock indefinitely when an already unlocked flush lock is repeatedly unlocked. Though this only currently occurs on filesystem shutdown, it has reproduced the effect of elevating an fs shutdown to a system-wide crash or hang. As it turns out, the flush lock is not actually required for the reclaim logic in xfs_reclaim_inode() because by that time we have already cycled the flush lock once while holding ILOCK_EXCL. Therefore, remove the additional flush lock/unlock cycle around the 'reclaim:' label and update branches into this label to release the flush lock where appropriate. Add an assert to xfs_ifunlock() to help prevent future occurences of the same problem. Reported-by:
Zorro Lang <zlang@redhat.com> Signed-off-by:
-
Darrick J. Wong authored
commit bec9d48d upstream. Check the minimum block size on v5 filesystems. [dchinner: cleaned up XFS_MIN_CRC_BLOCKSIZE check] Signed-off-by:
-
Eric Sandeen authored
commit 5d829300 upstream. The open-coded pattern: ifp->if_bytes / (uint)sizeof(xfs_bmbt_rec_t) is all over the xfs code; provide a new helper xfs_iext_count(ifp) to count the number of inline extents in an inode fork. [dchinner: pick up several missed conversions] Signed-off-by:
-
Brian Foster authored
commit 04197b34 upstream. We've had reports of generic/095 causing XFS to BUG() in __xfs_get_blocks() due to the existence of delalloc blocks on a direct I/O read. generic/095 issues a mix of various types of I/O, including direct and memory mapped I/O to a single file. This is clearly not supported behavior and is known to lead to such problems. E.g., the lack of exclusion between the direct I/O and write fault paths means that a write fault can allocate delalloc blocks in a region of a file that was previously a hole after the direct read has attempted to flush/inval the file range, but before it actually reads the block mapping. In turn, the direct read discovers a delalloc extent and cannot proceed. While the appropriate solution here is to not mix direct and memory mapped I/O to the same regions of the same file, the current BUG_ON() behavior is probably overkill as it can crash the entire system. Instead, localize the failure to the I/O in question by returning an error for a direct I/O that cannot be handled safely due to delalloc blocks. Be careful to allow the case of a direct write to post-eof delalloc blocks. This can occur due to speculative preallocation and is safe as post-eof blocks are not accompanied by dirty pages in pagecache (conversely, preallocation within eof must have been zeroed, and thus dirtied, before the inode size could have been increased beyond said blocks). Finally, provide an additional warning if a direct I/O write occurs while the file is memory mapped. This may not catch all problematic scenarios, but provides a hint that some known-to-be-problematic I/O methods are in use. Signed-off-by:
-
Brian Foster authored
commit 39937234 upstream. The cowblocks background scanner currently clears the cowblocks tag for inodes without any real allocations in the cow fork. This excludes inodes with only delalloc blocks in the cow fork. While we might never expect to clear delalloc blocks from the cow fork in the background scanner, it is not necessarily correct to clear the cowblocks tag from such inodes. For example, if the background scanner happens to process an inode between a buffered write and writeback, the scanner catches the inode in a state after delalloc blocks have been allocated to the cow fork but before the delalloc blocks have been converted to real blocks by writeback. The background scanner then incorrectly clears the cowblocks tag, even if part of the aforementioned delalloc reservation will not be remapped to the data fork (i.e., extra blocks due to the cowextsize hint). This means that any such additional blocks in the cow fork might never be reclaimed by the background scanner and could persist until the inode itself is reclaimed. To address this problem, only skip and clear inodes without any cow fork allocations whatsoever from the background scanner. While we generally do not want to cancel delalloc reservations from the background scanner, the pagecache dirty check following the cowblocks check should prevent that situation. If we do end up with delalloc cow fork blocks without a dirty address space mapping, this is probably an indication that something has gone wrong and the blocks should be reclaimed, as they may never be converted to a real allocation. Signed-off-by:
-
Darrick J. Wong authored
commit 4fd29ec4 upstream. Check the return value of xfs_trans_reserve_quota_nblks for errors. Signed-off-by:
-
Eric Sandeen authored
commit e6fc6fcf upstream. Source xfsprogs commit: ee3754254e8c186c99b6cdd4d59f741759d04acb Kernel commit 5ef828c4 ("xfs: avoid false quotacheck after unclean shutdown") made xfs_sb_from_disk() also call xfs_sb_quota_from_disk by default. However, when this was merged to libxfs, existing separate calls to libxfs_sb_quota_from_disk remained, and calling it twice in a row on a V4 superblock leads to issues, because: if (sbp->sb_qflags & XFS_PQUOTA_ACCT) { ... sbp->sb_pquotino = sbp->sb_gquotino; sbp->sb_gquotino = NULLFSINO; and after the second call, we have set both pquotino and gquotino to NULLFSINO. Fix this by making it safe to call twice, and also remove the extra calls to libxfs_sb_quota_from_disk. This is only spotted when running xfstests with "-m crc=0" because the sb_from_disk change came about after V5 became default, and the above behavior only exists on a V4 superblock. Reported-by:
-
