In later commit we are going to instantiate multiple attr instances
for flow instead of single attr.
Make sure the parsing using correct attr and not flow->attr.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Split pedit verify part into a new subfunction for better
maintainability.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Move pedit_headers_action from flow parse_state to flow parse_attr.
In a follow up commit we are going to have multiple attr per flow
and pedit_headers_action are unique per attr.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Move shared code to alloc_flow_attr_counter() for reuse by the next patches.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In later commit that we will have multiple attr instances per flow
we would like to pass a specific attr instance to set encaps.

Currently the mlx5_flow object contains a single mlx5_attr instance.
However, multi table actions (e.g. CT) instantiate multiple attr instances.

Currently mlx5e_attach/detach_encap() reads the first attr instance
from the flow instance. Modify the functions to receive the attr
instance as a parameter which is set by the calling function.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Split setting encap dests code chunk out of mlx5e_tc_add_fdb_flow()
to make the function smaller for maintainability and reuse.
For symmetry do the same for mlx5e_tc_del_fdb_flow().
While at it refactor cleanup to first check for encap flag like
done when setting encap dests.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

coccinelle report:
./drivers/ptp/ptp_sysfs.c:17:8-16:
WARNING: use scnprintf or sprintf
./drivers/ptp/ptp_sysfs.c:390:8-16:
WARNING: use scnprintf or sprintf

Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some systems there are compatibility issues with ASPM L1.2 and
RTL8125, therefore this state is disabled per default. To allow for
the L1.2 power saving on not affected systems, Realtek provides
vendors that successfully tested ASPM L1.2 the option to flag this
state as safe. According to Realtek this flag will be set first on
certain Chromebox devices.
Suggested-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: get rid of unused static inlines

I noticed a couple of unused static inline functions reviewing
net/sched patches so I run a grep thru all of include/ and net/
to catch other cases. This set removes the cases which look like
obvious dead code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IIUC the TIPC msg helpers are not meant to provide
and exhaustive API, so remove the unused ones.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Never used since it was added in v5.2.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used since v3.9.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used since v5.10.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used since v4.0.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used since added in v3.8.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not used since v2.6.37.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stubs under !CONFIG_IPV6 were missed when real functions
got deleted ca. v3.13.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

get_prp_lan_id() has never been used.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing takes the refcount since v4.9.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No caller since v3.16.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No callers since v5.7, the initial use case seems pretty
esoteric so removing this should not harm the completeness
of the API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

No callers since v3.15.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

NCI and HCI wrappers for nfc_set_vendor_cmds() exist,
use them. We could also remove the helpers.
It's a coin toss.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only caller of mii_lpa_to_linkmode_lpa_sgmii()
disappeared in v5.10.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefer kcalloc() to kzalloc(array_size()) for allocating an array.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following warning in mtk_star_emac.c if CONFIG_OF is not set:

drivers/net/ethernet/mediatek/mtk_star_emac.c:1559:34:
    warning: unused variable 'mtk_star_of_match' [-Wunused-const-variable]
    static const struct of_device_id mtk_star_of_match[] = {
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tobias Waldekranz says:

====================
net/fsl: xgmac_mdio: Preamble suppression and custom MDC frequencies

The first patch removes the docs for a binding that has never been
supported by the driver as far as I can see. This is a bit of a
mystery to me, maybe Freescale/NXP had/has support for it in an
internal version?

We then start working on the xgmac_mdio driver, converting the driver
to exclusively use managed resources, thereby simplifying the error
paths. Suggested by Andrew.

Preamble suppression is then added, followed by MDC frequency
customization. Neither code will change any bits if the corresponding
dt properties are not specified, so as to not trample on any setup
done by the bootloader, which boards might have relied on up to now.

Finally, we document the new bindings.

Tested on a T1023 based board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver now supports the standard "clock-frequency" and
"suppress-preamble" properties, do document them in the binding
description.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support the standard "clock-frequency" attribute to set the generated
MDC frequency. If not specified, the driver will leave the divisor
bits untouched.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support the standard "suppress-preamble" attribute to disable preamble
generation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

All of the resources used by this driver has managed interfaces, so
use them. Heed the warning in the comment before platform_get_resource
and use a bare devm_ioremap to allow for non-exclusive access to the
IO memory.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This property has never been supported by the driver. The kernel has
settled on "clock-frequency" as the standard name for this binding, so
once that is supported we will document that instead.

Fixes: 7f93c9d9 ("power/fsl: add MDIO dt binding for FMan")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Different netns has different requirement on the setting of min_adv_mss
sysctl which the advertised MSS will be never lower than.

Enable min_adv_mss to be configured per network namespace.
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
net: mvneta: use .mac_select_pcs()

This series converts mvneta to use the .mac_select_pcs() like eventually
everything else will be. mvneta is slightly more involved because we
need to rearrange the initialisation first to ensure everything required
is initialised prior to phylink_create() being called.

Tested locally on SolidRun Clearfog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert mvneta to use the mac_select_interface rather than using
phylink_set_pcs(). The intention here is to unify the approach for
PCS and eventually remove phylink_set_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-order the mvneta initialisation to move devm based resources and
easy setup earlier in the probe function. The primary reason for this
is to allow us to switch the driver to use phylink's mac_select_pcs()
callback.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Robert Hancock says:

====================
at803x fiber/SFP support

Add support for 1000Base-X fiber modes to the at803x PHY driver, as
well as support for connecting a downstream SFP cage.

Changes since v3:
-Renamed some constants with OHM suffix for clarity

Changes since v2:
-fixed tabs/spaces issue in one patch

Changes since v1:
-moved page selection to config_init so it is handled properly
after suspend/resume
-added explicit check for empty sfp_support bitmask
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for downstream SFP cages for AR8031 and AR8033. This is
primarily intended for fiber modules or direct-attach cables, however
copper modules which work in 1000Base-X mode may also function. Such
modules are allowed with a warning.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.

Enable the appropriate interrupt bits to detect fiber-side link up
or down events.

Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.

Fixes: c329e5af ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>