Make sure the removal of mappings uses the same logic that put the
mappings in place.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>

The function apei_estatus_print() and apei_estatus_check() forget to move ahead
the gdata pointer when dealing with multiple generic error data sections.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Len Brown <len.brown@intel.com>

The current code incorrectly assumes that
(1) the APEI register bit width is always 8, 16, 32, or 64 and
(2) the APEI register bit width is always equal to the APEI
    register access width.

ERST serialization instructions entries such as:

[030h 0048   1]                       Action : 00 [Begin Write Operation]
[031h 0049   1]                  Instruction : 03 [Write Register Value]
[032h 0050   1]        Flags (decoded below) : 01
                      Preserve Register Bits : 1
[033h 0051   1]                     Reserved : 00

[034h 0052  12]              Register Region : [Generic Address Structure]
[034h 0052   1]                     Space ID : 00 [SystemMemory]
[035h 0053   1]                    Bit Width : 03
[036h 0054   1]                   Bit Offset : 00
[037h 0055   1]         Encoded Access Width : 03 [DWord Access:32]
[038h 0056   8]                      Address : 000000007F2D7038

[040h 0064   8]                        Value : 0000000000000001
[048h 0072   8]                         Mask : 0000000000000007

break this assumption by yielding:
  [Firmware Bug]: APEI: Invalid bit width in GAR [0x7f2d7038/3/0]

I have found no ACPI specification requirements corresponding
with the above assumptions.  There is even a good example in
the Serialization Instruction Entries section (ACPI 4.0 section
17.4,1.2, ACPI 4.0a section 2.5.1.2, ACPI 5.0 section 18.5.1.2)
that mentions a serialization instruction with a bit range of
[6:2] which is 5 bits wide, _not_ 8, 16, 32, or 64 bits wide.

Compile and boot tested with 3.3.0-rc7 on a IBM HX5.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Add description of parameter notrigger in the einj.txt.
One can utilize this new parameter to do some SRAR injection
test. Pay attention, the operation is highly depended on the
BIOS implementation. If no proper BIOS supports it, even if
enabling this parameter, expected result will not happen.

v2:
  Update the documentation suggested by Tony
Suggested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Some APEI firmware implementation will access injected address
specified in param1 to trigger the error when injecting memory
error, which means if one SRAR error is injected, the crash
always happens because it is executed in kernel context. This
new parameter can disable trigger action and control is taken
over by the user. In this way, an SRAR error can happen in user
context instead of crashing the system. This function is highly
depended on BIOS implementation so please ensure you know the
BIOS trigger procedure before you enable this switch.

v2:
  notrigger should be created together with param1/param2
Tested-by: Tony Luck <tony.luck@lintel.com>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

On the platforms with ACPI4.x support, parameter extension
is not always doable, which means only parameter extension
is enabled, einj_param can take effect.

v2->v1: stopping early in einj_get_parameter_address for einj_param
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

This fixes a trivial copy & paste error in ERST header length check.
It's just for future safety because sizeof(struct acpi_table_einj)
equals to sizeof(struct acpi_table_erst) with current ACPI5.0
specification. It applies to v3.3-rc6.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Commit 28d82dc1 ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).

The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.

This is captured in: https://bugzilla.redhat.com/show_bug.cgi?id=681578Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking changes from David Miller:
 "1) icmp6_dst_alloc() returns NULL instead of ERR_PTR() leading to
     crashes, particularly during shutdown.  Reported by Dave Jones and
     fixed by Eric Dumazet.

  2) hyperv and wimax/i2400m return NETDEV_TX_BUSY when they have
     already freed the SKB, which causes crashes as to the caller this
     means requeue the packet.  Fixes from Eric Dumazet.

  3) usbnet driver doesn't allocate the right amount of headroom on
     fresh RX SKBs, fix from Eric Dumazet.

  4) Fix regression in ip6_mc_find_dev_rcu(), as an RCU lookup it
     abolutely should not take a reference to 'dev', this leads to
     leaks.  Fix from RonQing Li.

  5) Fix netfilter ctnetlink race between delete and timeout expiration.
     From Pablo Neira Ayuso.

  6) Revert SFQ change which causes regressions, specifically queueing
     to tail can lead to unavoidable flow starvation.  From Eric
     Dumazet.

  7) Fix a memory leak and a crash on corrupt firmware files in bnx2x,
     from Michal Schmidt."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netfilter: ctnetlink: fix race between delete and timeout expiration
  ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
  wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
  net/hyperv: fix erroneous NETDEV_TX_BUSY use
  net/usbnet: reserve headroom on rx skbs
  bnx2x: fix memory leak in bnx2x_init_firmware()
  bnx2x: fix a crash on corrupt firmware file
  sch_sfq: revert dont put new flow at the end of flows
  ipv6: fix icmp6_dst_alloc()

Pull perf fixes from Ingo Molnar.

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools, x86: Build perf on older user-space as well
  perf tools: Use scnprintf where applicable
  perf tools: Incorrect use of snprintf results in SEGV

Kerin Millar reported hardlockups while running `conntrackd -c'
in a busy firewall. That system (with several processors) was
acting as backup in a primary-backup setup.

After several tries, I found a race condition between the deletion
operation of ctnetlink and timeout expiration. This patch fixes
this problem.
Tested-by: Kerin Millar <kerframil@gmail.com>
Reported-by: Kerin Millar <kerframil@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_mc_find_dev_rcu() is called with rcu_read_lock(), so don't
need to dev_hold().
With dev_hold(), not corresponding dev_put(), will lead to leak.

[ bug introduced in 96b52e61 (ipv6: mcast: RCU conversions) ]
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge some more email patches from Andrew Morton:
 "A couple of nilfs fixes"

* emailed from Andrew Morton <akpm@linux-foundation.org>:
  nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
  nilfs2: clamp ns_r_segments_percentage to [1, 99]

According to the report from Slicky Devil, nilfs caused kernel oops at
nilfs_load_super_block function during mount after he shrank the
partition without resizing the filesystem:

 BUG: unable to handle kernel NULL pointer dereference at 00000048
 IP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2]
 *pde = 00000000
 Oops: 0000 [#1] PREEMPT SMP
 ...
 Call Trace:
  [<d0d7a87b>] init_nilfs+0x4b/0x2e0 [nilfs2]
  [<d0d6f707>] nilfs_mount+0x447/0x5b0 [nilfs2]
  [<c0226636>] mount_fs+0x36/0x180
  [<c023d961>] vfs_kern_mount+0x51/0xa0
  [<c023ddae>] do_kern_mount+0x3e/0xe0
  [<c023f189>] do_mount+0x169/0x700
  [<c023fa9b>] sys_mount+0x6b/0xa0
  [<c04abd1f>] sysenter_do_call+0x12/0x28
 Code: 53 18 8b 43 20 89 4b 18 8b 4b 24 89 53 1c 89 43 24 89 4b 20 8b 43
 20 c7 43 2c 00 00 00 00 23 75 e8 8b 50 68 89 53 28 8b 54 b3 20 <8b> 72
 48 8b 7a 4c 8b 55 08 89 b3 84 00 00 00 89 bb 88 00 00 00
 EIP: [<d0d7a08e>] nilfs_load_super_block+0x17e/0x280 [nilfs2] SS:ESP 0068:ca9bbdcc
 CR2: 0000000000000048

This turned out due to a defect in an error path which runs if the
calculated location of the secondary super block was invalid.

This patch fixes it and eliminates the reported oops.
Reported-by: Slicky Devil <slicky.dvl@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Slicky Devil <slicky.dvl@gmail.com>
Cc: <stable@vger.kernel.org>	[2.6.30+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ns_r_segments_percentage is read from the disk.  Bogus or malicious
value could cause integer overflow and malfunction due to meaningless
disk usage calculation.  This patch reports error when mounting such
bogus volumes.
Signed-off-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull maintainer update from James Morris:
 "Please pull this patch which adds Serge as maintainer of the
  capabilities code, as discussed on lwn and the lsm list.

  New capabilities must be signed off by the maintainer, and new uses of
  any capabilities should at be cc'd to the maintainer."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  MAINTAINERS: Add Serge as maintainer of capabilities

Pull c6x bugfix from Mark Salter:
 "Remove dead code from entry.S which causes a build failure when using
  a newer assembler (v2.22 complains about it, v2.20 ignores it)."

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  C6X: remove dead code from entry.S

When writing files to afs I sometimes hit a BUG:

kernel BUG at fs/afs/rxrpc.c:179!

With a backtrace of:

	afs_free_call
	afs_make_call
	afs_fs_store_data
	afs_vnode_store_data
	afs_write_back_from_locked_page
	afs_writepages_region
	afs_writepages

The cause is:

	ASSERT(skb_queue_empty(&call->rx_queue));

Looking at a tcpdump of the session the abort happens because we
are exceeding our disk quota:

	rx abort fs reply store-data error diskquota exceeded (32)

So the abort error is valid. We hit the BUG because we haven't
freed all the resources for the call.

By freeing any skbs in call->rx_queue before calling afs_free_call
we avoid hitting leaking memory and avoid hitting the BUG.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A read of a large file on an afs mount failed:

# cat junk.file > /dev/null
cat: junk.file: Bad message

Looking at the trace, call->offset wrapped since it is only an
unsigned short. In afs_extract_data:

        _enter("{%u},{%zu},%d,,%zu", call->offset, len, last, count);
...

        if (call->offset < count) {
                if (last) {
                        _leave(" = -EBADMSG [%d < %zu]", call->offset, count);
                        return -EBADMSG;
                }

Which matches the trace:

[cat   ] ==> afs_extract_data({65132},{524},1,,65536)
[cat   ] <== afs_extract_data() = -EBADMSG [0 < 65536]

call->offset went from 65132 to 0. Fix this by making call->offset an
unsigned int.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The ENDPROC() on sys_fadvise64_c6x() in arch/c6x/kernel/entry.S is
outside of the conditional block with the matching ENTRY() macro. This
leads a newer (v2.22 vs. v2.20) assembler to complain:

  /tmp/ccGZBaPT.s: Assembler messages:
  /tmp/ccGZBaPT.s: Error: .size expression for sys_fadvise64_c6x does not evaluate to a constant

The conditional block became dead code when c6x switched to generic
unistd.h and should be removed along with the offending ENDPROC().
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>

A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.

In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.

In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK

Also increments tx_dropped counter
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.

This is mostly a revert of commit bf769375 (staging: hv: fix the return
status of netvsc_start_xmit())

In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.

In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.

This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.

Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d47a0ac7 (sch_sfq: dont put new flow at the end of
flows)

As Jesper found out, patch sounded great but has bad side effects.

In stress situation, pushing new flows in front of the queue can prevent
old flows doing any progress. Packets can stay in SFQ queue for
unlimited amount of time.

It's possible to add heuristics to limit this problem, but this would
add complexity outside of SFQ scope.

A more sensible answer to Dave Taht concerns (who reported the issued I
tried to solve in original commit) is probably to use a qdisc hierarchy
so that high prio packets dont enter a potentially crowded SFQ qdisc.
Reported-by: Jesper Dangaard Brouer <jdb@comx.dk>
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 87a11578 ( ipv6: Move xfrm_lookup() call down into
icmp6_dst_alloc().) forgot to convert one error path, leading
to crashes in mld_sendpack()

Many thanks to Dave Jones for providing a very complete bug report.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Serge as maintainer of capabilities, per suggestion on LWN:
http://lwn.net/Articles/486306/Signed-off-by: James Morris <james.l.morris@oracle.com>

Merge patches from Andrew Morton:
 "Nine patches - some bug fixes and some MAINTAINERS fiddling."

* emailed from Andrew Morton <akpm@linux-foundation.org>:
  drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
  MAINTAINERS: add entry for exynos mipi display drivers
  MAINTAINERS: fix link to Gustavo Padovans tree
  MAINTAINERS: add Johan to Bluetooth maintainers
  MAINTAINERS: Gustavo has moved
  prctl: use CAP_SYS_RESOURCE for PR_SET_MM option
  rapidio/tsi721: fix bug in register offset definitions
  MAINTAINERS: update ST's Mailing list for SPEAr
  memcg: free mem_cgroup by RCU to fix oops

Pull i2c subsystem fixes from Jean Delvare.

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-algo-bit: Fix spurious SCL timeouts under heavy load
  i2c-core: Comment says "transmitted" but means "received"

Pull hwmon fixes from Guenter Roeck.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (zl6100) Enable interval between chip accesses for all chips
  hwmon: (w83627ehf) Describe undocumented pwm attributes
  hwmon: (w83627ehf) Fix temp2 source for W83627UHG
  hwmon: (w83627ehf) Fix memory leak in probe function
  hwmon: (w83627ehf) Fix writing into fan_stop_time for NCT6775F/NCT6776F

Pull drm exynos/intel updates from Dave Airlie:
 "Two minor updates from Jesse for Intel SNB fixes, and a few fixes from
  Samsung for exynos.  The pull req has Alan's commit in it since Intel
  based their tree on my tree at that time, but it all seems fine wrt
  merging."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm exynos: use drm_fb_helper_set_par directly
  drm/exynos: Fix fb_videomode <-> drm_mode_modeinfo conversion
  drm/exynos: fix runtime_pm fimd device state on probe
  drm/exynos: use correct 'exynos-drm' name for platform device
  drm/i915: support 32 bit BGR formats in sprite planes
  drm/i915: fix color order for BGR formats on SNB
  drm/gma500: Fix Cedarview boot failures in 3.3-rc

Pull media fixes from Mauro Carvalho Chehab:
 "For 4 fixes for 3.3 (all trivial):
       - uvc video driver: fixes a division by zero;
       - davinci: add module.h to fix compilation;
       - smsusb: fix the delivery system setting;
       - smsdvb: the get_frontend implementation there is broken.

  The smsdvb patch has 127 lines, but it is trivial: instead of
  returning a cache of the set_frontend (with is wrong, as it doesn't
  have the updated values for the data, and the implementation there is
  buggy), it copies the information of the detected DVB parameters from
  the smsdvb private structures into the corresponding DVBv5 struct
  fields."

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] smsdvb: fix get_frontend
  [media] smsusb: fix the default delivery system setting
  [media] media: davinci: added module.h to resolve unresolved macros
  [media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation

Pull target fixes from Nicholas Bellinger:
 "This series addresses two recently reported regression bugs related to
  legacy SCSI reservation usage in target core, and iscsi-target
  reservation conflict handling.

  The second patch in particular addresses possible data-corruption with
  SCSI reservations that is specific to iscsi-target fabric LUNs with
  multiple client writers.  Both patches need to go into v3.2 stable
  ASAP, and the branch based on the last target-pending/3.3-rc-fixes
  HEAD.

  Again, thanks to Martin Svec for his help to identify and address this
  regression bug with iscsi-target."

* '3.3-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Fix reservation conflict -EBUSY response handling bug
  target: Fix compatible reservation handling (CRH=1) with legacy RESERVE/RELEASE

strict_strtoul() writes a long but ->gamma_mode only has space to store an
int, so on 64 bit systems we end up scribbling over ->gamma_table_count as
well.  I've changed it to use kstrtouint() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'd like to add Inki Dae, Donghwa Lee and Kyungmin Park as maintainers
who developers for exynos mipi display drivers for
video/driver/exynos/exynos_mipi* and include/video/exynos_mipi*.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Gustavo's tree is called just bluetooth.git and not bluetooth-2.6.git
anymore.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I've been coordinating Bluetooth patches in my tree for some time and
it's possible I'll do it in the future too, so add myself to the
Bluetooth sections as well as mention my tree there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is going to be the primary e-mail for kernel development.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>