Pull driver core updates from Greg KH:
 "Here is the driver core / firmware changes for 4.2-rc1.

  A number of small changes all over the place in the driver core, and
  in the firmware subsystem.  Nothing really major, full details in the
  shortlog.  Some of it is a bit of churn, given that the platform
  driver probing changes was found to not work well, so they were
  reverted.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (31 commits)
  Revert "base/platform: Only insert MEM and IO resources"
  Revert "base/platform: Continue on insert_resource() error"
  Revert "of/platform: Use platform_device interface"
  Revert "base/platform: Remove code duplication"
  firmware: add missing kfree for work on async call
  fs: sysfs: don't pass count == 0 to bin file readers
  base:dd - Fix for typo in comment to function driver_deferred_probe_trigger().
  base/platform: Remove code duplication
  of/platform: Use platform_device interface
  base/platform: Continue on insert_resource() error
  base/platform: Only insert MEM and IO resources
  firmware: use const for remaining firmware names
  firmware: fix possible use after free on name on asynchronous request
  firmware: check for file truncation on direct firmware loading
  firmware: fix __getname() missing failure check
  drivers: of/base: move of_init to driver_init
  drivers/base: cacheinfo: fix annoying typo when DT nodes are absent
  sysfs: disambiguate between "error code" and "failure" in comments
  driver-core: fix build for !CONFIG_MODULES
  driver-core: make __device_attach() static
  ...

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver pull request for 4.2-rc1.

  Lots of mei, extcon, coresight, uio, mic, and other driver updates in
  here.  Full details in the shortlog.  All of these have been in
  linux-next for some time with no reported problems"

* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
  mei: me: wait for power gating exit confirmation
  mei: reset flow control on the last client disconnection
  MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
  misc: sram: sort and clean up included headers
  misc: sram: move reserved block logic out of probe function
  misc: sram: add private struct device and virt_base members
  misc: sram: report correct SRAM pool size
  misc: sram: bump error message level on unclean driver unbinding
  misc: sram: fix device node reference leak on error
  misc: sram: fix enabled clock leak on error path
  misc: mic: Fix reported static checker warning
  misc: mic: Fix randconfig build error by including errno.h
  uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
  uio: pruss: Add CONFIG_HAS_IOMEM dependence
  uio: pruss: Include <linux/sizes.h>
  extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
  char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
  Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
  parport: check exclusive access before register
  w1: use correct lock on error in w1_seq_show()
  ...

Pull tracing updates from Steven Rostedt:
 "This patch series contains several clean ups and even a new trace
  clock "monitonic raw".  Also some enhancements to make the ring buffer
  even faster.  But the biggest and most noticeable change is the
  renaming of the ftrace* files, structures and variables that have to
  deal with trace events.

  Over the years I've had several developers tell me about their
  confusion with what ftrace is compared to events.  Technically,
  "ftrace" is the infrastructure to do the function hooks, which include
  tracing and also helps with live kernel patching.  But the trace
  events are a separate entity altogether, and the files that affect the
  trace events should not be named "ftrace".  These include:

    include/trace/ftrace.h         ->    include/trace/trace_events.h
    include/linux/ftrace_event.h   ->    include/linux/trace_events.h

  Also, functions that are specific for trace events have also been renamed:

    ftrace_print_*()               ->    trace_print_*()
    (un)register_ftrace_event()    ->    (un)register_trace_event()
    ftrace_event_name()            ->    trace_event_name()
    ftrace_trigger_soft_disabled() ->    trace_trigger_soft_disabled()
    ftrace_define_fields_##call()  ->    trace_define_fields_##call()
    ftrace_get_offsets_##call()    ->    trace_get_offsets_##call()

  Structures have been renamed:

    ftrace_event_file              ->    trace_event_file
    ftrace_event_{call,class}      ->    trace_event_{call,class}
    ftrace_event_buffer            ->    trace_event_buffer
    ftrace_subsystem_dir           ->    trace_subsystem_dir
    ftrace_event_raw_##call        ->    trace_event_raw_##call
    ftrace_event_data_offset_##call->    trace_event_data_offset_##call
    ftrace_event_type_funcs_##call ->    trace_event_type_funcs_##call

  And a few various variables and flags have also been updated.

  This has been sitting in linux-next for some time, and I have not
  heard a single complaint about this rename breaking anything.  Mostly
  because these functions, variables and structures are mostly internal
  to the tracing system and are seldom (if ever) used by anything
  external to that"

* tag 'trace-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
  ring_buffer: Allow to exit the ring buffer benchmark immediately
  ring-buffer-benchmark: Fix the wrong type
  ring-buffer-benchmark: Fix the wrong param in module_param
  ring-buffer: Add enum names for the context levels
  ring-buffer: Remove useless unused tracing_off_permanent()
  ring-buffer: Give NMIs a chance to lock the reader_lock
  ring-buffer: Add trace_recursive checks to ring_buffer_write()
  ring-buffer: Allways do the trace_recursive checks
  ring-buffer: Move recursive check to per_cpu descriptor
  ring-buffer: Add unlikelys to make fast path the default
  tracing: Rename ftrace_get_offsets_##call() to trace_event_get_offsets_##call()
  tracing: Rename ftrace_define_fields_##call() to trace_event_define_fields_##call()
  tracing: Rename ftrace_event_type_funcs_##call to trace_event_type_funcs_##call
  tracing: Rename ftrace_data_offset_##call to trace_event_data_offset_##call
  tracing: Rename ftrace_raw_##call event structures to trace_event_raw_##call
  tracing: Rename ftrace_trigger_soft_disabled() to trace_trigger_soft_disabled()
  tracing: Rename FTRACE_EVENT_FL_* flags to EVENT_FILE_FL_*
  tracing: Rename struct ftrace_subsystem_dir to trace_subsystem_dir
  tracing: Rename ftrace_event_name() to trace_event_name()
  tracing: Rename FTRACE_MAX_EVENT to TRACE_EVENT_TYPE_MAX
  ...

Pull tracing fixes from Steven Rostedt:
 "This isn't my 4.2 pull request (yet).  I found a few more bugs that I
  would have sent to fix 4.1, but since 4.1 is already out, I'm sending
  this before sending my 4.2 request (which is ready to go).

  After fixing the previous filter issue reported by Vince Weaver, I
  could not come up with a situation where the operand counter (cnt)
  could go below zero, so I added a WARN_ON_ONCE(cnt < 0).  Vince was
  able to trigger that warn on with his fuzzer test, but didn't have a
  filter input that caused it.

  Later, Sasha Levin was able to trigger that same warning, and was able
  to give me the filter string that triggered it.  It was simply a
  single operation ">".

  I wrapped the filtering code in a userspace program such that I could
  single step through the logic.  With a single operator the operand
  counter can legitimately go below zero, and should be reported to the
  user as an error, but should not produce a kernel warning.  The
  WARN_ON_ONCE(cnt < 0) should be just a "if (cnt < 0) break;" and the
  code following it will produce the error message for the user.

  While debugging this, I found that there was another bug that let the
  pointer to the filter string go beyond the filter string.  This too
  was fixed.

  Finally, there was a typo in a stub function that only gets compiled
  if trace events is disabled but tracing is enabled (I'm not even sure
  that's possible)"

* tag 'trace-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Fix typo from "static inlin" to "static inline"
  tracing/filter: Do not allow infix to exceed end of string
  tracing/filter: Do not WARN on operand count going below zero

Pull drm updates from Dave Airlie:
 "This is the main drm pull request for v4.2.

  I've one other new driver from freescale on my radar, it's been posted
  and reviewed, I'd just like to get someone to give it a last look, so
  maybe I'll send it or maybe I'll leave it.

  There is no major nouveau changes in here, Ben was working on
  something big, and we agreed it was a bit late, there wasn't anything
  else he considered urgent to merge.

  There might be another msm pull for some bits that are waiting on
  arm-soc, I'll see how we time it.

  This touches some "of" stuff, acks are in place except for the fixes
  to the build in various configs,t hat I just applied.

  Summary:

  New drivers:
      - virtio-gpu:
                KMS only pieces of driver for virtio-gpu in qemu.
                This is just the first part of this driver, enough to run
                unaccelerated userspace on. As qemu merges more we'll start
                adding the 3D features for the virgl 3d work.
      - amdgpu:
                a new driver from AMD to driver their newer GPUs. (VI+)
                It contains a new cleaner userspace API, and is a clean
                break from radeon moving forward, that AMD are going to
                concentrate on. It also contains a set of register headers
                auto generated from AMD internal database.

  core:
      - atomic modesetting API completed, enabled by default now.
      - Add support for mode_id blob to atomic ioctl to complete interface.
      - bunch of Displayport MST fixes
      - lots of misc fixes.

  panel:
      - new simple panels
      - fix some long-standing build issues with bridge drivers

  radeon:
      - VCE1 support
      - add a GPU reset counter for userspace
      - lots of fixes.

  amdkfd:
      - H/W debugger support module
      - static user-mode queues
      - support killing all the waves when a process terminates
      - use standard DECLARE_BITMAP

  i915:
      - Add Broxton support
      - S3, rotation support for Skylake
      - RPS booting tuning
      - CPT modeset sequence fixes
      - ns2501 dither support
      - enable cmd parser on haswell
      - cdclk handling fixes
      - gen8 dynamic pte allocation
      - lots of atomic conversion work

  exynos:
      - Add atomic modesetting support
      - Add iommu support
      - Consolidate drm driver initialization
      - and MIC, DECON and MIPI-DSI support for exynos5433

  omapdrm:
      - atomic modesetting support (fixes lots of things in rewrite)

  tegra:
      - DP aux transaction fixes
      - iommu support fix

  msm:
      - adreno a306 support
      - various dsi bits
      - various 64-bit fixes
      - NV12MT support

  rcar-du:
      - atomic and misc fixes

  sti:
      - fix HDMI timing complaince

  tilcdc:
      - use drm component API to access tda998x driver
      - fix module unloading

  qxl:
      - stability fixes"

* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (872 commits)
  drm/nouveau: Pause between setting gpu to D3hot and cutting the power
  drm/dp/mst: close deadlock in connector destruction.
  drm: Always enable atomic API
  drm/vgem: Set unique to "vgem"
  of: fix a build error to of_graph_get_endpoint_by_regs function
  drm/dp/mst: take lock around looking up the branch device on hpd irq
  drm/dp/mst: make sure mst_primary mstb is valid in work function
  of: add EXPORT_SYMBOL for of_graph_get_endpoint_by_regs
  ARM: dts: rename the clock of MIPI DSI 'pll_clk' to 'sclk_mipi'
  drm/atomic: Don't set crtc_state->enable manually
  drm/exynos: dsi: do not set TE GPIO direction by input
  drm/exynos: dsi: add support for MIC driver as a bridge
  drm/exynos: dsi: add support for Exynos5433
  drm/exynos: dsi: make use of array for clock access
  drm/exynos: dsi: make use of driver data for static values
  drm/exynos: dsi: add macros for register access
  drm/exynos: dsi: rename pll_clk to sclk_clk
  drm/exynos: mic: add MIC driver
  of: add helper for getting endpoint node of specific identifiers
  drm/exynos: add Exynos5433 decon driver
  ...

Pull device mapper fixes from Mike Snitzer:
 "Apologies for not pressing this request-based DM partial completion
  issue further, it was an oversight on my part.  We'll have to get it
  fixed up properly and revisit for a future release.

   - Revert block and DM core changes the removed request-based DM's
     ability to handle partial request completions -- otherwise with the
     current SCSI LLDs these changes could lead to silent data
     corruption.

   - Fix two DM version bumps that were missing from the initial 4.2 DM
     pull request (enabled userspace lvm2 to know certain changes have
     been made)"

* tag 'dm-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache policy smq: fix "default" version to be 1.4.0
  dm: bump the ioctl version to 4.32.0
  Revert "block, dm: don't copy bios for request clones"
  Revert "dm: do not allocate any mempools for blk-mq request-based DM"

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - move -O0 jitterentropy code into its own file instead of using gcc
     pragma magic.

   - kill testmgr warning for gcm-aes-aesni.

   - fix build failure in old rsa.

  Other minor fixes:

   - ignore asn1 files generated by new rsa.

   - remove unnecessary kzfree NULL checks in jitterentropy.

   - typo fix in akcipher"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: rsa - add .gitignore for crypto/*.-asn1.[ch] files
  crypto: asymmetric_keys/rsa - Use non-conflicting variable name
  crypto: testmgr - don't print info about missing test for gcm-aes-aesni
  crypto: jitterentropy - Delete unnecessary checks before the function call "kzfree"
  crypto: akcipher - fix spelling cihper -> cipher
  crypto: jitterentropy - avoid compiler warnings

Pull ARM updates from Russell King:
 "Bigger items included in this update are:

   - A series of updates from Arnd for ARM randconfig build failures
   - Updates from Dmitry for StrongARM SA-1100 to move IRQ handling to
     drivers/irqchip/
   - Move ARMs SP804 timer to drivers/clocksource/
   - Perf updates from Mark Rutland in preparation to move the ARM perf
     code into drivers/ so it can be shared with ARM64.
   - MCPM updates from Nicolas
   - Add support for taking platform serial number from DT
   - Re-implement Keystone2 physical address space switch to conform to
     architecture requirements
   - Clean up ARMv7 LPAE code, which goes in hand with the Keystone2
     changes.
   - L2C cleanups to avoid unlocking caches if we're prevented by the
     secure support to unlock.
   - Avoid cleaning a potentially dirty cache containing stale data on
     CPU initialisation
   - Add ARM-only entry point for secondary startup (for machines that
     can only call into a Thumb kernel in ARM mode).  Same thing is also
     done for the resume entry point.
   - Provide arch_irqs_disabled via asm-generic
   - Enlarge ARMv7M vector table
   - Always use BFD linker for VDSO, as gold doesn't accept some of the
     options we need.
   - Fix an incorrect BSYM (for Thumb symbols) usage, and convert all
     BSYM compiler macros to a "badr" (for branch address).
   - Shut up compiler warnings provoked by our cmpxchg() implementation.
   - Ensure bad xchg sizes fail to link"

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (75 commits)
  ARM: Fix build if CLKDEV_LOOKUP is not configured
  ARM: fix new BSYM() usage introduced via for-arm-soc branch
  ARM: 8383/1: nommu: avoid deprecated source register on mov
  ARM: 8391/1: l2c: add options to overwrite prefetching behavior
  ARM: 8390/1: irqflags: Get arch_irqs_disabled from asm-generic
  ARM: 8387/1: arm/mm/dma-mapping.c: Add arm_coherent_dma_mmap
  ARM: 8388/1: tcm: Don't crash when TCM banks are protected by TrustZone
  ARM: 8384/1: VDSO: force use of BFD linker
  ARM: 8385/1: VDSO: group link options
  ARM: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
  ARM: remove __bad_xchg definition
  ARM: 8369/1: ARMv7M: define size of vector table for Vybrid
  ARM: 8382/1: clocksource: make ARM_TIMER_SP804 depend on GENERIC_SCHED_CLOCK
  ARM: 8366/1: move Dual-Timer SP804 driver to drivers/clocksource
  ARM: 8365/1: introduce sp804_timer_disable and remove arm_timer.h inclusion
  ARM: 8364/1: fix BE32 module loading
  ARM: 8360/1: add secondary_startup_arm prototype in header file
  ARM: 8359/1: correct secondary_startup_arm mode
  ARM: proc-v7: sanitise and document registers around errata
  ARM: proc-v7: clean up MIDR access
  ...

Pull ARM SoC defconfig updates from Kevin Hilman:
 "We keep collecting defconfig updates in a separate branch mostly to
  encourage people to handle them separately and avoid conflicts between
  different topics.

  Most of these are enablement of new SoCs, boards or drivers that have
  come in, or minor config refreshes due to reorderings in Kconfig
  files, etc.  I.e. mostly minor churn of various kinds"

* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
  ARM: multi_v7_defconfig: remove duplicate CONFIG_COMMON_CLK_QCOM=y
  ARM: multi_v7_defconfig: Enable display on Trats2 board
  ARM64: add GPIO keys to the defconfig
  ARM: keystone: defconfig: enable netcp driver by default
  ARM: exynos_defconfig: Enable CONFIG_SENSORS_INA2XX for Odroid-XU3
  ARM: exynos_defconfig: Enable CONFIG_SENSORS_PWM_FAN for Odroid-XU3
  ARM: omap2plus_defconfig: Enable TOUCHSCREEN_PIXCIR
  ARM: omap2plus_defconfig: Add dm816x USB PHY as a loadable module
  ARM: omap2plus_defconifg: Enable DM9000 in omap2plus_defconfig
  ARM: lpc18xx: remove DEBUG_LL_UART_8250 from defconfig
  ARM: multi_v7_defconfig: Make media support modular
  ARM: multi_v7_defconfig: Make sound support modular
  ARM: multi_v7_defconfig: Enable shmobile r8a7778/bockw platform
  ARM: exynos_defconfig: savedefconfig
  ARM: exynos_defconfig: Enable display on Trats2 board
  ARM: multi_v7_defconfig: Enable OHCI on exynos SoCs
  ARM: multi_v7_defconfig: Enable TMU for exynos SoCs
  ARM: multi_v7_defconfig: Enable PMIC and MUIC drivers for exynos
  ARM: multi_v7_defconfig: Enable CPU idle for exynos SoCs
  ARM: multi_v7_defconfig: Enable Cypress APA I2C Trackpad support
  ...

Pull ARM SoC driver updates from Kevin Hilman:
 "Some of these are for drivers/soc, where we're now putting
  SoC-specific drivers these days.  Some are for other driver subsystems
  where we have received acks from the appropriate maintainers.

  Some highlights:

   - simple-mfd: document DT bindings and misc updates
   - migrate mach-berlin to simple-mfd for clock, pinctrl and reset
   - memory: support for Tegra132 SoC
   - memory: introduce tegra EMC driver for scaling memory frequency
   - misc. updates for ARM CCI and CCN busses"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: soc: sunxi: Introduce SoC driver to map SRAMs
  arm-cci: Add aliases for PMU events
  arm-cci: Add CCI-500 PMU support
  arm-cci: Sanitise CCI400 PMU driver specific code
  arm-cci: Abstract handling for CCI events
  arm-cci: Abstract out the PMU counter details
  arm-cci: Cleanup PMU driver code
  arm-cci: Do not enable CCI-400 PMU by default
  firmware: qcom: scm: Add HDCP Support
  ARM: berlin: add an ADC node for the BG2Q
  ARM: berlin: remove useless chip and system ctrl compatibles
  clk: berlin: drop direct of_iomap of nodes reg property
  ARM: berlin: move BG2Q clock node
  ARM: berlin: move BG2CD clock node
  ARM: berlin: move BG2 clock node
  clk: berlin: prepare simple-mfd conversion
  pinctrl: berlin: drop SoC stub provided regmap
  ARM: berlin: move pinctrl to simple-mfd nodes
  pinctrl: berlin: prepare to use regmap provided by syscon
  reset: berlin: drop arch_initcall initialization
  ...

Pull ARM SoC DT updates from Kevin Hilman:
 "As usual, quite a few device-tree updates in ARM land.  There was one
  minor churn in DTs due to relicensing under a dual-license, and lots
  of little additions of new peripherals, features etc, but nothing
  really exciting to call to your attention.  Some higlights, focsuing
  on support for new SoCs and boards:

   - AT91: new boards: Overkiz,  Acme Systems' Arietta G25
   - tegra: HDA support
   - bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
     RT-AC87U
   - mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
     boards, DLink DNS-327L
   - OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
     SL50
   - ARM: added support for Juno r1 board
   - sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
     Mele A1000G
   - imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
     Gateworks GW5510, and aristainetos2 boards
   - hisilicon: hi6220 SoC support; new boards: 96boards hikey"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
  ARM: hisi: revert changes from hisi/hip04-dt branch
  ARM: nomadik: set proper compatible for accelerometer
  ARM64: juno: add GPIO keys
  ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
  ARM: dts: Introduce STM32F429 MCU
  ARM: socfpga: dts: enable ethernet for Arria10 devkit
  ARM: dts: k2l: fix the netcp range size
  ARM: dts: k2e: fix the netcp range size
  ARM: dts: k2hk: fix the netcp range size
  ARM: dts: k2l-evm: Add device bindings for netcp driver
  ARM: dts: k2e-evm: Add device bindings for netcp driver
  ARM: dts: k2hk-evm: Add device bindings for netcp driver
  ARM: BCM5301X: Add DT for Asus RT-AC87U
  ARM: BCM5301X: add IRQ numbers for PCIe controller
  ARM: BCM5301X: add NAND flash chip description
  arm64: dts: Add dts files for Hisilicon Hi6220 SoC
  clk: hi6220: Document devicetree bindings for hi6220 clock
  arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
  ARM: at91/dt: sama5d4ek: mci0 uses slot 0
  ARM: at91/dt: kizbox: fix mismatch LED PWM device
  ...

Pull ARM SoC platform support updates from Kevin Hilman:
 "Our SoC branch usually contains expanded support for new SoCs and
  other core platform code.  Some highlights from this round:

   - sunxi: SMP support for A23 SoC
   - socpga: big-endian support
   - pxa: conversion to common clock framework
   - bcm: SMP support for BCM63138
   - imx: support new I.MX7D SoC
   - zte: basic support for ZX296702 SoC"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (134 commits)
  ARM: zx: Add basic defconfig support for ZX296702
  ARM: dts: zx: add an initial zx296702 dts and doc
  clk: zx: add clock support to zx296702
  dt-bindings: Add #defines for ZTE ZX296702 clocks
  ARM: socfpga: fix build error due to secondary_startup
  MAINTAINERS: ARM64: EXYNOS: Extend entry for ARM64 DTS
  ARM: ep93xx: simone: support for SPI-based MMC/SD cards
  MAINTAINERS: update Shawn's email to use kernel.org one
  ARM: socfpga: support suspend to ram
  ARM: socfpga: add CPU_METHOD_OF_DECLARE for Arria 10
  ARM: socfpga: use CPU_METHOD_OF_DECLARE for socfpga_cyclone5
  ARM: EXYNOS: register power domain driver from core_initcall
  ARM: EXYNOS: use PS_HOLD based poweroff for all supported SoCs
  ARM: SAMSUNG: Constify platform_device_id
  ARM: EXYNOS: Constify irq_domain_ops
  ARM: EXYNOS: add coupled cpuidle support for Exynos3250
  ARM: EXYNOS: add exynos_get_boot_addr() helper
  ARM: EXYNOS: add exynos_set_boot_addr() helper
  ARM: EXYNOS: make exynos_core_restart() less verbose
  ARM: EXYNOS: fix exynos_boot_secondary() return value on timeout
  ...

Pull ARM SoC cleanups from Kevin Hilman:
 "A relatively small setup of cleanups this time around, and similar to
  last time the bulk of it is removal of legacy board support:

   - OMAP: removal of legacy (non-DT) booting for several platforms

   - i.MX: remove some legacy board files"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: fix EFM32 build breakage caused by cpu_resume_arm
  ARM: 8389/1: Add cpu_resume_arm() for firmwares that resume in ARM state
  ARM: v7 setup function should invalidate L1 cache
  mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
  ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
  ARM: OMAP2+: Constify irq_domain_ops
  ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
  ARM: at91: remove useless Makefile.boot
  ARM: at91: remove at91rm9200_sdramc.h
  ARM: at91: remove mach/at91_ramc.h and mach/at91rm9200_mc.h
  ARM: at91/pm: use the atmel-mc syscon defines
  pcmcia: at91_cf: Use syscon to configure the MC/smc
  ARM: at91: declare the at91rm9200 memory controller as a syscon
  mfd: syscon: Add Atmel MC (Memory Controller) registers definition
  ARM: at91: drop sam9_smc.c
  ata: at91: use syscon to configure the smc
  ARM: ux500: delete static resource defines
  ARM: ux500: rename ux500_map_io
  ARM: ux500: look up PRCMU resource from DT
  ARM: ux500: kill off L2CC static map
  ...

Merge second patchbomb from Andrew Morton:

 - most of the rest of MM

 - lots of misc things

 - procfs updates

 - printk feature work

 - updates to get_maintainer, MAINTAINERS, checkpatch

 - lib/ updates

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (96 commits)
  exit,stats: /* obey this comment */
  coredump: add __printf attribute to cn_*printf functions
  coredump: use from_kuid/kgid when formatting corename
  fs/reiserfs: remove unneeded cast
  NILFS2: support NFSv2 export
  fs/befs/btree.c: remove unneeded initializations
  fs/minix: remove unneeded cast
  init/do_mounts.c: add create_dev() failure log
  kasan: remove duplicate definition of the macro KASAN_FREE_PAGE
  fs/efs: femove unneeded cast
  checkpatch: emit "NOTE: <types>" message only once after multiple files
  checkpatch: emit an error when there's a diff in a changelog
  checkpatch: validate MODULE_LICENSE content
  checkpatch: add multi-line handling for PREFER_ETHER_ADDR_COPY
  checkpatch: suggest using eth_zero_addr() and eth_broadcast_addr()
  checkpatch: fix processing of MEMSET issues
  checkpatch: suggest using ether_addr_equal*()
  checkpatch: avoid NOT_UNIFIED_DIFF errors on cover-letter.patch files
  checkpatch: remove local from codespell path
  checkpatch: add --showfile to allow input via pipe to show filenames
  ...

Commit bccab6a0 ("dm cache: switch the "default" cache replacement
policy from mq to smq") should've incremented the "default" policy's
version number to 1.4.0 rather than reverting to version 1.0.0.
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This fix enables userspace to detect that the dm-stats changes from the
4.2 merge are in place.
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This reverts commit 5f1b670d.

Justification for revert as reported in this dm-devel post:
https://www.redhat.com/archives/dm-devel/2015-June/msg00160.html

this change should not be pushed to mainline yet.

Firstly, Christoph has a newer version of the patch that fixes silent
data corruption problem:
  https://www.redhat.com/archives/dm-devel/2015-May/msg00229.html

And the new version still depends on LLDDs to always complete requests
to the end when error happens, while block API doesn't enforce such a
requirement. If the assumption is ever broken, the inconsistency between
request and bio (e.g. rq->__sector and rq->bio) will cause silent data
corruption:
  https://www.redhat.com/archives/dm-devel/2015-June/msg00022.htmlReported-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This reverts commit cbc4e3c1.
Reported-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Pull RTC updates from Alexandre Belloni:
 "Core:
   - Coding style and whitespace fixes (interface, Makefile and Kconfig)
   - New rtc_tm_sub() helper
   - New CONFIG_RTC_SYSTOHC_DEVICE option
   - Removed rtc_set_mmss()

  New drivers:
   - Mediatek MT6397
   - Cortina Gemini

  Drivers:
   - Year 2106 fixes for isl1208, pcf8563 and sunxi
   - update author email for at32ap700x and efi
   - ds1307: alarm fix
   - efi: use correct EFI 'epoch'
   - hym8563: make irq optional
   - imxdi: cleanups and better handling of the security/tamper monitoring
   - snvs: fix wakealarm
   - Compilation fixes or warning removal for gemini, mt6397, palmas, pfc8563
   - Trivial cleanups for ab8500, ds1216, ds1286, ds1672, ep93xx,
     hid-sensor-time, max6900, max8998, max77686, max77802, mc13xxx, mv,
     mxc, s3c, spear, v3020
   - Kconfig fixes for stmp3xxx and xgene"

* tag 'rtc-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (48 commits)
  rtc: remove useless I2C dependencies
  rtc: whitespace fixes
  rtc: Properly sort Makefile
  MAINTAINERS: Add RTC subsystem repository
  rtc: pfc8563: fix uninitialized variable warning
  rtc: ds1307: Enable the mcp794xx alarm after programming time
  rtc: hym8563: make the irq optional
  rtc: gemini: fix cocci warnings
  rtc: mv: correct 24 hour error message
  rtc: mv: use BIT()
  rtc: efi: use correct EFI 'epoch'
  rtc: interface: Remove rtc_set_mmss()
  sparc: time: Replace update_persistent_clock() with CONFIG_RTC_SYSTOHC
  rtc: NTP: Add CONFIG_RTC_SYSTOHC_DEVICE for NTP synchronization
  rtc: sunxi: Replace deprecated rtc_tm_to_time()
  rtc: isl1208: Replace deprecated rtc_tm_to_time()
  rtc: Introduce rtc_tm_sub() helper function
  rtc: pcf8563: Replace deprecated rtc_time_to_tm() and rtc_tm_to_time()
  rtc: palmas: Initialise bb_charging flag before using it
  rtc: simplify use of devm_ioremap_resource
  ...

Pull i2c updates from Wolfram Sang:
 "Highlights:

   - new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
   - major updates to at91, davinci
   - bugfixes to the mux infrastructure when dealing with the new quirk
     mechanism
   - more users for the bus recovery feature
   - further improvements to the slave framework

  Plus the usual bunch of smaller driver and core improvements and
  fixes.

  There is one patch removing old code from an ARM platform.  This has
  been acked by the sh_mobile maintainer Simon Horman"

* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
  i2c: busses: i2c-bcm2835: limits cdiv to allowed values
  i2c: sh_mobile: use proper type for timeout
  i2c: sh_mobile: use adapter default for timeout
  i2c: rcar: use proper type for timeout
  i2c: rcar: use adapter default for timeout
  i2c: designware: Make sure the device is suspended before disabling runtime PM
  i2c: tegra: apply size limit quirk
  i2c: tegra: don't advertise SMBUS_QUICK
  i2c: octeon: remove unused signal handling
  i2c: davinci: Optimize SCL generation
  i2c: mux: pca954x: Use __i2c_transfer because of quirks
  i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
  i2c: use parent adapter quirks in mux
  i2c: bcm2835: clear reserved bits in S-Register
  ARM: shmobile: r8a7740: remove I2C errata handling
  i2c: sh_mobile: add errata workaround
  i2c: at91: fix code checker warnings
  i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
  i2c: davinci: Avoid sending to own address
  i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
  ...

Pull mailbox updates from Jassi Brar.

* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox/bcm2835: Fix mailbox full detection.
  dt: mailbox: Remove 'mbox-names property is discouraged' message from binding
  mailbox: Add ability for clients to request channels by name
  mailbox: Enable BCM2835 mailbox support
  dt/bindings: Add binding for the BCM2835 mailbox driver
  mailbox: Fix up error handling in mbox_request_channel()
  mailbox: Make mbox_chan_ops const
  mailbox: altera: Add dependency on HAS_IOMEM

Pull edac updates from Mauro Carvalho Chehab:
 "Some fixes and additions to the EDAC driver used on modern Intel x86
  CPUs.  It includes support for Broadwell EP/EX platforms and fixes for
  motherboards with more than 2 CPU sockets"

* tag 'edac/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
  sb_edac: support for Broadwell -EP and -EX
  sb_edac: Fix support for systems with two home agents per socket
  sb_edac: Fix a typo and a thinko in address handling for Haswell
  EDAC: Remove arbitrary limit on number of channels

Pull media updates from Mauro Carvalho Chehab:

 - Lots of improvements at the DVB API DocBook documentation.  Now, the
   frontend and the network APIs are fully in sync with the Kernel and
   looks more like the rest of the media documentation;

 - New frontend driver: cx24120

 - New driver for a PCI device: cobalt.  This driver is actually not
   sold in the market, but it is a good example of a multi-HDMI input
   device;

 - The dt3155 driver were promoted from staging;

 - The mantis driver got remote controller support;

 - New V4L2 driver for ST bdisp SoC chipsets;

 - Make sparse and smatch happier: several bugs were solved by fixing
   the issues reported by those static code analyzers.

 - Lots of new device additions, new features, improvements and cleanups
   at the existing drivers.

* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
  [media] lmedm04: fix the range for relative measurements
  [media] lmedm04: use u32 instead of u64 for relative stats
  [media] omap3isp: remove unused var
  [media] saa7134: fix page size on some archs
  [media] use CONFIG_PM_SLEEP for suspend/resume
  [media] tuner-i2c: be consistent with I2C declaration
  [media] si470x: cleanup define namespace
  [media] bdisp: prevent compiling on random arch
  [media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
  [media] MAINTAINERS: Add entry for the Renesas VSP1 driver
  [media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
  [media] Revert "[media] vb2: Push mmap_sem down to memops"
  [media] mantis: cleanup a warning
  [media] bdisp-debug: don't try to divide by s64
  [media] cx88: don't declare restart_video_queue if not used
  [media] au0828: move dev->boards atribuition to happen earlier
  [media] lmedm04: implement dvb v5 statistics
  [media] bdisp: remove unused var
  [media] bdisp: remove needless check
  ts2020: fix compilation on i386
  ...

Pull thermal management updates from Zhang Rui:
 "Specifics:

   - enhance Thermal Framework with several new capabilities:

       * use power estimates
       * compute weights with relative integers instead of percentages
       * allow governors to have private data in thermal zones
       * export thermal zone parameters through sysfs

     Thanks to the ARM thermal team (Javi, Punit, KP).

   - introduce a new thermal governor: power allocator.  First in kernel
     closed loop PI(D) controller for thermal control.  Thanks to ARM
     thermal team.

   - enhance OF thermal to allow thermal zones to have sustainable power
     HW specification.  Thanks to Punit.

   - introduce thermal driver for Intel Quark SoC x1000platform.  Thanks
     to Ong, Boon Leong.

   - introduce QPNP PMIC temperature alarm driver.  Thanks to Ivan T. I.

   - introduce thermal driver for Hisilicon hi6220.  Thanks to
     kongxinwei.

   - enhance Exynos thermal driver to handle Exynos5433 TMU.  Thanks to
     Chanwoo C.

   - TI thermal driver now has a better implementation for EOCZ bit.
     From Pavel M.

   - add id for Skylake processors in int340x processor thermal driver.

   - a couple of small fixes and cleanups."

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (36 commits)
  thermal: hisilicon: add new hisilicon thermal sensor driver
  dt-bindings: Document the hi6220 thermal sensor bindings
  thermal: of-thermal: add support for reading coefficients property
  thermal: support slope and offset coefficients
  thermal: power_allocator: round the division when divvying up power
  thermal: exynos: Add the support for Exynos5433 TMU
  thermal: cpu_cooling: Fix power calculation when CPUs are offline
  thermal: cpu_cooling: Remove cpu_dev update on policy CPU update
  thermal: export thermal_zone_parameters to sysfs
  thermal: cpu_cooling: Check memory allocation of power_table
  ti-soc-thermal: request temperature periodically if hw can't do that itself
  ti-soc-thermal: implement eocz bit to make driver useful on omap3
  cleanup ti-soc-thermal
  thermal: remove stale THERMAL_POWER_ACTOR select
  thermal: Default OF created trip points to writable
  thermal: core: Add Kconfig option to enable writable trips
  thermal: x86_pkg_temp: drop const for thermal_zone_parameters
  of: thermal: Introduce sustainable power for a thermal zone
  thermal: add trace events to the power allocator governor
  thermal: introduce the Power Allocator governor
  ...

On the MacBook Pro, power of the gpu is cut by a gmux chip. Sometimes
the gpu gets stuck in powersaving mode and refuses to wake up
("Refused to change power state, currently in D3"). Inserting a
delay between setting the gpu to D3hot and cutting the power seems
to help (most of the time). This issue and its (partial) remediation
by the patch was observed with an Nvidia GT650M (NVE7 / GK107).
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Pull sound updates from Takashi Iwai:
 "It was a busy development cycle at this time, as you can see a wide
  range of changes in diffstat.  There are no big changes but many
  refactoring and improvements.  Here we go some highlights:

  ALSA core:
   - Procfs codes were cleaned up to use seq_file
   - Procfs can be opt out via Kconfig (only for EXPERT)
   - Two types of jack API were unified finally; now both kctl and input
     jack devs are handled via a single function call.

  HD-audio:
   - Continued code restructuring for the future ASoC driver; now HDA
     controller driver is split to a core helper module.
   - Preliminary codes for Skylake audio support in HDA core.
   - Proper i915 gfx power well management for SKL & co
   - Enabled runtime PM as default for Intel HDMI/DP codecs
   - Newer Tegra chip supports
   - More quirks for Dell headsets, Alienware (with CA0132), etc.
   - A couple of DRM ELD helper API functions

  ASoC:
   - Support for loading ASoC topology maps from firmware, intended to
     be used to allow self-describing DSP firmware images to be built
     which can map controls added by the DSP to userspace without the
     kernel needing to know about individual DSP firmwares
   - Lots of refactoring to avoid direct access to snd_soc_codec where
     it's not needed supporting future refactoring
   - Big refactoring, cleanup and enhancement for the Wolfson ADSP
     driver
   - Cleanup series for TI TAS2552 and R-CAR drivers
   - Fixes and improvements on RT56xx codecs
   - Support for TI TAS571x power amplifiers
   - Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs
   - Support for x86 systems with RT5650 and Qualcomm Storm
   - Support for Mediatek AFE (Audio Front End) unit
   - Other various small fixes to ASoC codec drivers

  Firewire:
   - Enhanced to allow non-blocking streams to use timestamp
     synchronization
   - Improve support for DM1500 and BeBoBv3

  Misc:
   - Cleanup of old pci API functions over all PCI sound drivers
   - Fix long-standing regression of the old powermac i2c setup"

* tag 'sound-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (533 commits)
  ALSA: pcm: Fix pcm_class sysfs output
  ALSA: hda-beep: Update authors dead email address
  ASoC: wm_adsp: Move DSP Rate controls into the codec
  ASoC: wm8995: Fix setting sysclk for WM8995_SYSCLK_MCLK2 case
  ALSA: hda: provide default bus io ops extended hdac
  ALSA: hda: add hda link cleanup routine
  ALSA: hda: add hdac_ext stream creation and cleanup routines
  ASoC: rsrc-card: remove unused ret
  ALSA: HDAC: move SND_HDA_PREALLOC_SIZE to core
  ASoC: mediatek: Add machine driver for rt5650 rt5676 codec
  ASoC: mediatek: Add machine driver for MAX98090 codec
  ASoC: mediatek: Add AFE platform driver
  ASoC: rsnd: remove io from rsnd_mod
  ASoC: rsnd: move rsnd_mod_is_working() to rsnd_io_is_working()
  ASoC: rsnd: don't use rsnd_mod_to_io() on snd_kcontrol
  ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_src_xxx()
  ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()
  ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_dma_xxx()
  ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_get_adinr()
  ASoC: rsnd: add common interrupt handler for SSI/SRC/DMA
  ...

Pull DMI updates from Jean Delvare:
 "The most important change is the new sysfs interface to the DMI table,
  which will let user-space tools (such as dmidecode) access the table
  without relying on /dev/mem"

* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  firmware: dmi: struct dmi_header should be packed
  firmware: dmi_scan: Coding style cleanups
  Documentation: ABI: sysfs-firmware-dmi: add -entries suffix to file name
  firmware: dmi_scan: add SBMIOS entry and DMI tables
  firmware: dmi_scan: Trim DMI table length before exporting it
  firmware: dmi_scan: Rename dmi_table to dmi_decode_table
  firmware: dmi: List my quilt tree
  firmware: dmi_scan: Only honor end-of-table for 64-bit tables

There is a helpful comment in do_exit() that states we sync the mm's RSS
info before statistics gathering.

The function that does the statistics gathering is called right above that
comment.

Change the code to obey the comment.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This allows detecting improper format string at build time, like:

  fs/coredump.c:225:5: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'int' [-Wformat=]
       err = cn_printf(cn, "%ld", cprm->siginfo->si_signo);
       ^

As si_signo is always an int, the format should be %d here.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When adding __printf attribute to cn_printf, gcc reports some issues:

  fs/coredump.c:213:5: warning: format '%d' expects argument of type
  'int', but argument 3 has type 'kuid_t' [-Wformat=]
       err = cn_printf(cn, "%d", cred->uid);
       ^
  fs/coredump.c:217:5: warning: format '%d' expects argument of type
  'int', but argument 3 has type 'kgid_t' [-Wformat=]
       err = cn_printf(cn, "%d", cred->gid);
       ^

These warnings come from the fact that the value of uid/gid needs to be
extracted from the kuid_t/kgid_t structure before being used as an
integer.  More precisely, cred->uid and cred->gid need to be converted to
either user-namespace uid/gid or to init_user_ns uid/gid.

Use init_user_ns in order not to break existing ABI, and document this in
Documentation/sysctl/kernel.txt.

While at it, format uid and gid values with %u instead of %d because
uid_t/__kernel_uid32_t and gid_t/__kernel_gid32_t are unsigned int.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmem_cache_alloc() returns void*.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The "fh_len" passed to ->fh_to_* is not guaranteed to be that same as that
returned by encode_fh - it may be larger.

With NFSv2, the filehandle is fixed length, so it may appear longer than
expected and be zero-padded.

So we must test that fh_len is at least some value, not exactly equal to
it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bh, od_sup and this_node are unconditionally initialized in
befs_bt_read_super() and befs_btree_find()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmem_cache_alloc() returns void*.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If create_dev() function fails to create the root mount device
(/dev/root), then it goes to panic as root device not found but there is
no printk in this case.  So I have added the log in case it fails to
create the root device.  It will help in debugging.

[akpm@linux-foundation.org: simplify printk(), use pr_emerg(), display errno]
Signed-off-by: Vishnu Pratap Singh <vishnu.ps@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Dan Ehrenberg <dehrenberg@chromium.org>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove duplicate definition of the macro KASAN_FREE_PAGE in
mm/kasan/kasan.h
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Acked-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kmem_cache_alloc() returns void*.
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make this message similar to the "false positives" message and emit it
only once when scanning multiple files instead of after each file scanned.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

People often put diff snippets in changelogs.  This causes problems
when one tries to apply a file containing both the changelog and the
diff because patch(1) tries to apply the diff which it found in the
changelog.

Warn once when what seems to be a diff snippet in the changelog exists.
Signed-off-by: Joe Perches <joe@perches.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

There is a well defined list of expected values for MODULE_LICENSE so warn
the user upon usage of unknown values.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>