- 09 May, 2024 5 commits
-
-
Eric Dumazet authored
Various ndo_set_config() methods can change dev->if_port dev->if_port is going to be read locklessly from rtnl_fill_link_ifmap(). Add corresponding WRITE_ONCE() on writer sides. Signed-off-by:
Eric Dumazet <edumazet@google.com> Reviewed-by:
Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240507184144.1230469-1-edumazet@google.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Eric Dumazet authored
There is no need to use this_cpu_ptr(dst_cache->cache) twice. Compiler is unable to optimize the second call, because of per-cpu constraints. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20240507132717.627518-1-edumazet@google.comSigned-off-by:
-
Eric Dumazet authored
dst_cache->reset_ts is read or written locklessly, add READ_ONCE() and WRITE_ONCE() annotations. Signed-off-by:
-
Donald Hunter authored
Add support for retrieving VFs as part of link info. For example: ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/rt_link.yaml \ --do getlink --json '{"ifi-index": 38, "ext-mask": ["vf", "skip-stats"]}' {'address': 'b6:75:91:f2:64:65', [snip] 'vfinfo-list': {'info': [{'broadcast': b'\xff\xff\xff\xff\xff\xff\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00', 'link-state': {'link-state': 'auto', 'vf': 0}, 'mac': {'mac': b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00', 'vf': 0}, 'rate': {'max-tx-rate': 0, 'min-tx-rate': 0, 'vf': 0}, 'rss-query-en': {'setting': 0, 'vf': 0}, 'spoofchk': {'setting': 0, 'vf': 0}, 'trust': {'setting': 0, 'vf': 0}, 'tx-rate': {'rate': 0, 'vf': 0}, 'vlan': {'qos': 0, 'vf': 0, 'vlan': 0}, 'vlan-list': {'info': [{'qos': 0, 'vf': 0, 'vlan': 0, 'vlan-proto': 0}]}}, {'broadcast': b'\xff\xff\xff\xff\xff\xff\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00', 'link-state': {'link-state': 'auto', 'vf': 1}, 'mac': {'mac': b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00' b'\x00\x00\x00\x00\x00\x00\x00\x00', 'vf': 1}, 'rate': {'max-tx-rate': 0, 'min-tx-rate': 0, 'vf': 1}, 'rss-query-en': {'setting': 0, 'vf': 1}, 'spoofchk': {'setting': 0, 'vf': 1}, 'trust': {'setting': 0, 'vf': 1}, 'tx-rate': {'rate': 0, 'vf': 1}, 'vlan': {'qos': 0, 'vf': 1, 'vlan': 0}, 'vlan-list': {'info': [{'qos': 0, 'vf': 1, 'vlan': 0, 'vlan-proto': 0}]}}]}, 'xdp': {'attached': 0}} Signed-off-by:Donald Hunter <donald.hunter@gmail.com> Link: https://lore.kernel.org/r/20240507103603.23017-1-donald.hunter@gmail.comSigned-off-by:
-
Alexandru Gagniuc authored
Add a compatible property specific to IPQ9574. This should be used along with the IPQ4019 compatible. This second compatible serves the same purpose as the ipq{5,6,8} compatibles. This is to indicate that the clocks properties are required. Signed-off-by:Alexandru Gagniuc <mr.nuke.me@gmail.com> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20240507024758.2810514-1-mr.nuke.me@gmail.comSigned-off-by:
-
- 08 May, 2024 25 commits
-
-
Lukasz Majewski authored
Without this change the created netns instances are not cleared after this script execution. To fix this problem the cleanup_all_ns function from ../lib.sh is called. Signed-off-by:
Lukasz Majewski <lukma@denx.de> Reviewed-by:
David S. Miller <davem@davemloft.net>
-
Joel Granados authored
Remove the explicit call to "return" in the void ax25_ds_set_timer function that was introduced in 78a7b5db ("ax.25: x.25: Remove the now superfluous sentinel elements from ctl_table array"). Signed-off-by:
Joel Granados <j.granados@samsung.com> Signed-off-by:
-
Alexander Mikhalitsyn authored
Let's make all IPVS sysctls writtable even when network namespace is owned by non-initial user namespace. Let's make a few sysctls to be read-only for non-privileged users: - sync_qlen_max - sync_sock_size - run_estimation - est_cpulist - est_nice I'm trying to be conservative with this to prevent introducing any security issues in there. Maybe, we can allow more sysctls to be writable, but let's do this on-demand and when we see real use-case. This patch is motivated by user request in the LXC project [1]. Having this can help with running some Kubernetes [2] or Docker Swarm [3] workloads inside the system containers. Link: https://github.com/lxc/lxc/issues/4278 [1] Link: https://github.com/kubernetes/kubernetes/blob/b722d017a34b300a2284b890448e5a605f21d01e/pkg/proxy/ipvs/proxier.go#L103 [2] Link: https://github.com/moby/libnetwork/blob/3797618f9a38372e8107d8c06f6ae199e1133ae8/osl/namespace_linux.go#L682 [3] Cc: Julian Anastasov <ja@ssi.bg> Cc: Simon Horman <horms@verge.net.au> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Jozsef Kadlecsik <kadlec@netfilter.org> Cc: Florian Westphal <fw@strlen.de> Signed-off-by:
Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com> Acked-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
Alexander Mikhalitsyn authored
Cc: Julian Anastasov <ja@ssi.bg> Cc: Simon Horman <horms@verge.net.au> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Jozsef Kadlecsik <kadlec@netfilter.org> Cc: Florian Westphal <fw@strlen.de> Suggested-by:
-
Christian Marangi authored
Currently the ipq806x dwmac driver is almost always used attached to the CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii". Some device came up with a special configuration where the PHY is directly attached to the GMAC port and in those case phy-mode needs to be set to "rgmii-id" to make the PHY correctly work and receive packets. Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id" (or variants) mode is set, the mode is rejected and probe fails. Add support also for these phy-modes to correctly setup PHYs that requires delay applied to tx/rx. Signed-off-by:
Christian Marangi <ansuelsmth@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Oleksij Rempel authored
Enhance the error reporting mechanism in the switchdev framework to provide more informative and user-friendly error messages. Following feedback from users struggling to understand the implications of error messages like "failed (err=-28) to add object (id=2)", this update aims to clarify what operation failed and how this might impact the system or network. With this change, error messages now include a description of the failed operation, the specific object involved, and a brief explanation of the potential impact on the system. This approach helps administrators and developers better understand the context and severity of errors, facilitating quicker and more effective troubleshooting. Example of the improved logging: [ 70.516446] ksz-switch spi0.0 uplink: Failed to add Port Multicast Database entry (object id=2) with error: -ENOSPC (-28). [ 70.516446] Failure in updating the port's Multicast Database could lead to multicast forwarding issues. [ 70.516446] Current HW/SW setup lacks sufficient resources. This comprehensive update includes handling for a range of switchdev object IDs, ensuring that most operations within the switchdev framework benefit from clearer error reporting. Reviewed-by:Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by:
-
Peilin He authored
Introduce a tracepoint for icmp_send, which can help users to get more detail information conveniently when icmp abnormal events happen. 1. Giving an usecase example: ============================= When an application experiences packet loss due to an unreachable UDP destination port, the kernel will send an exception message through the icmp_send function. By adding a trace point for icmp_send, developers or system administrators can obtain detailed information about the UDP packet loss, including the type, code, source address, destination address, source port, and destination port. This facilitates the trouble-shooting of UDP packet loss issues especially for those network-service applications. 2. Operation Instructions: ========================== Switch to the tracing directory. cd /sys/kernel/tracing Filter for destination port unreachable. echo "type==3 && code==3" > events/icmp/icmp_send/filter Enable trace event. echo 1 > events/icmp/icmp_send/enable 3. Result View: ================ udp_client_erro-11370 [002] ...s.12 124.728002: icmp_send: icmp_send: type=3, code=3. From 127.0.0.1:41895 to 127.0.0.1:6666 ulen=23 skbaddr=00000000589b167a Signed-off-by:Peilin He <he.peilin@zte.com.cn> Signed-off-by:
xu xin <xu.xin16@zte.com.cn> Reviewed-by:
Yunkai Zhang <zhang.yunkai@zte.com.cn> Cc: Yang Yang <yang.yang29@zte.com.cn> Cc: Liu Chun <liu.chun2@zte.com.cn> Cc: Xuexin Jiang <jiang.xuexin@zte.com.cn> Reviewed-by:
Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by:
-
David S. Miller authored
Oleksij Rempel says: ==================== add DCB and DSCP support for KSZ switches This patch series is aimed at improving support for DCB (Data Center Bridging) and DSCP (Differentiated Services Code Point) on KSZ switches. The main goal is to introduce global DSCP and PCP (Priority Code Point) mapping support, addressing the limitation of KSZ switches not having per-port DSCP priority mapping. This involves extending the DSA framework with new callbacks for managing trust settings for global DSCP and PCP maps. Additionally, we introduce IEEE 802.1q helpers for default configurations, benefiting other drivers too. Change logs are in separate patches. Compared to v6 this series includes some new patches for DSCP global mapping support and QoS selftest script for KSZ9477 switches. ==================== Signed-off-by: -
Oleksij Rempel authored
Add tests covering following functionality on KSZ9477 switch family: - default port priority - global DSCP to Internal Priority Mapping - apptrust configuration This script was tested on KSZ9893R Signed-off-by:
-
Oleksij Rempel authored
Microchip KSZ and LAN variants do not have per port DSCP priority configuration. Instead there is a global DSCP mapping table. This patch provides write access to this global DSCP map. In case entry is "deleted", we map corresponding DSCP entry to a best effort prio, which is expected to be the default priority for all untagged traffic. Signed-off-by:
-
Oleksij Rempel authored
Some switches like Microchip KSZ variants do not support per port DSCP priority configuration. Instead there is a global DSCP mapping table. To handle it, we will accept set/del request to any of user ports to make global configuration and update dcb app entries for all other ports. Signed-off-by:
-
Oleksij Rempel authored
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do all needed initial configuration. Signed-off-by:
Arun Ramadoss <arun.ramadoss@microchip.com> Signed-off-by:
-
Oleksij Rempel authored
Init priority to queue mapping in the way as it shown in IEEE 802.1Q mapping example. Signed-off-by:
-
Oleksij Rempel authored
I tested ETS support on KSZ9893, so it should work other KSZ989X variants too, which was till not listed as support. With this change we now officially not support only ksz8 family of chips. Signed-off-by:
-
Oleksij Rempel authored
KSZ88X3 switches have different behavior on different ports: - It seems to be not possible to disable VLAN PCP classification on port 2. It means, as soon as mutliqueue support is enabled, frames with VLAN tag will get PCP prios. This behavior do not affect Port 1 - it is possible to disable PCP prios. - DSCP classification is not working on Port 2. Since there are still usable configuration combinations, I added some quirks to make sure user will get appropriate error message if not possible configuration is chosen. Signed-off-by: -
Oleksij Rempel authored
Add DCB support to configure app trust sources and default port priority. Following commands can be used for testing: dcb apptrust set dev lan1 order pcp dscp dcb app replace dev lan1 default-prio 3 Since it is not possible to configure DSCP-Prio mapping per port, this patch provide only ability to read switch global dscp-prio mapping and way to enable/disable app trust for DSCP. Signed-off-by:
-
Oleksij Rempel authored
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue() to support KSZ8795 and KSZ88X3 families of switches. Per default, configure KSZ88X3 to use one queue, since it need special handling due to priority related errata. Errata handling is implemented in a separate patch. Signed-off-by:
-
Oleksij Rempel authored
IEEE 802.1q specification provides recommendation and examples which can be used as good default values for different drivers. This patch implements mapping examples documented in IEEE 802.1Q-2022 in Annex I "I.3 Traffic type to traffic class mapping" and IETF DSCP naming and mapping DSCP to Traffic Type inspired by RFC8325. This helpers will be used in followup patches for dsa/microchip DCB implementation. Signed-off-by:
-
Oleksij Rempel authored
Most of Microchip KSZ switches use Internal Priority Value associated with every frame. For example, it is possible to map any VLAN PCP or DSCP value to IPV and at the end, map IPV to a queue. Since amount of IPVs is not equal to amount of queues, add this information and make use of it in some functions. Signed-off-by:
-
Oleksij Rempel authored
Add DCB support to get/set trust configuration for different packet priority information sources. Some switch allow to chose different source of packet priority classification. For example on KSZ switches it is possible to configure VLAN PCP and/or DSCP sources. Signed-off-by:
Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2024-05-06 (ice) This series contains updates to ice driver only. Paul adds support for additional E830 devices and adjusts naming for existing E830 devices. Marcin commonizes a couple of TC setup calls to reduce duplicated code. Mateusz adds ice_vsi_cfg_params into ice_vsi to consolidate info. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsi ice: Deduplicate tc action setup ice: update E830 device ids and comments ice: add additional E830 device ids ==================== Link: https://lore.kernel.org/r/20240506170827.948682-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Eric Dumazet authored
Some usb drivers set small skb->truesize and break core networking stacks. In this patch, I removed one of the skb->truesize override. I also replaced one skb_clone() by an allocation of a fresh and small skb, to get minimally sized skbs, like we did in commit 1e2c6117 ("net: cdc_ncm: reduce skb truesize in rx path") and 4ce62d5b ("net: usb: ax88179_178a: stop lying about skb->truesize") Fixes: c9b37458 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support") Signed-off-by:
-
Eric Dumazet authored
Some usb drivers try to set small skb->truesize and break core networking stacks. In this patch, I removed one of the skb->truesize override. I also replaced one skb_clone() by an allocation of a fresh and small skb, to get minimally sized skbs, like we did in commit 1e2c6117 ("net: cdc_ncm: reduce skb truesize in rx path") and 4ce62d5b ("net: usb: ax88179_178a: stop lying about skb->truesize") Signed-off-by:
-
Eric Dumazet authored
Some usb drivers try to set small skb->truesize and break core networking stacks. I replace one skb_clone() by an allocation of a fresh and small skb, to get minimally sized skbs, like we did in commit 1e2c6117 ("net: cdc_ncm: reduce skb truesize in rx path") and 4ce62d5b ("net: usb: ax88179_178a: stop lying about skb->truesize") Fixes: 361459cd ("net: usb: aqc111: Implement RX data path") Signed-off-by:
-
John Hubbard authored
When building with clang, via: make LLVM=1 -C tools/testing/selftest ...clang warns about three variables that are not initialized in all cases: 1) The opt_ipproto_off variable is used uninitialized if "testname" is not "ip". Willem de Bruijn pointed out that this is an actual bug, and suggested the fix that I'm using here (thanks!). 2) The addr_len is used uninitialized, but only in the assert case, which bails out, so this is harmless. 3) The family variable in add_listener() is only used uninitialized in the error case (neither IPv4 nor IPv6 is specified), so it's also harmless. Fix by initializing each variable. Signed-off-by:John Hubbard <jhubbard@nvidia.com> Reviewed-by:
Willem de Bruijn <willemb@google.com> Acked-by:
Mat Martineau <martineau@kernel.org> Link: https://lore.kernel.org/r/20240506190204.28497-1-jhubbard@nvidia.comSigned-off-by:
-
- 07 May, 2024 10 commits
-
-
Florian Fainelli authored
Allow the Dynamic Interrupt Moderation (DIM) library to be built as a module. This is particularly useful in an Android GKI (Google Kernel Image) configuration where everything is built as a module, including Ethernet controller drivers. Having to build DIMLIB into the kernel image with potentially no user is wasteful. Signed-off-by:
Alexander Lobakin <aleksander.lobakin@intel.com> Link: https://lore.kernel.org/r/20240506175040.410446-1-florian.fainelli@broadcom.comSigned-off-by:
-
Eric Dumazet authored
subflow_add_reset_reason(skb, ...) can fail. We can not assume mptcp_get_ext(skb) always return a non NULL pointer. syzbot reported: general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN PTI KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f] CPU: 0 PID: 5098 Comm: syz-executor132 Not tainted 6.9.0-rc6-syzkaller-01478-gcdc74c9d #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 RIP: 0010:subflow_v6_route_req+0x2c7/0x490 net/mptcp/subflow.c:388 Code: 8d 7b 07 48 89 f8 48 c1 e8 03 42 0f b6 04 20 84 c0 0f 85 c0 01 00 00 0f b6 43 07 48 8d 1c c3 48 83 c3 18 48 89 d8 48 c1 e8 03 <42> 0f b6 04 20 84 c0 0f 85 84 01 00 00 0f b6 5b 01 83 e3 0f 48 89 RSP: 0018:ffffc9000362eb68 EFLAGS: 00010206 RAX: 0000000000000003 RBX: 0000000000000018 RCX: ffff888022039e00 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff88807d961140 R08: ffffffff8b6cb76b R09: 1ffff1100fb2c230 R10: dffffc0000000000 R11: ffffed100fb2c231 R12: dffffc0000000000 R13: ffff888022bfe273 R14: ffff88802cf9cc80 R15: ffff88802ad5a700 FS: 0000555587ad2380(0000) GS:ffff8880b9400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f420c3f9720 CR3: 0000000022bfc000 CR4: 00000000003506f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tcp_conn_request+0xf07/0x32c0 net/ipv4/tcp_input.c:7180 tcp_rcv_state_process+0x183c/0x4500 net/ipv4/tcp_input.c:6663 tcp_v6_do_rcv+0x8b2/0x1310 net/ipv6/tcp_ipv6.c:1673 tcp_v6_rcv+0x22b4/0x30b0 net/ipv6/tcp_ipv6.c:1910 ip6_protocol_deliver_rcu+0xc76/0x1570 net/ipv6/ip6_input.c:438 ip6_input_finish+0x186/0x2d0 net/ipv6/ip6_input.c:483 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 NF_HOOK+0x3a4/0x450 include/linux/netfilter.h:314 __netif_receive_skb_one_core net/core/dev.c:5625 [inline] __netif_receive_skb+0x1ea/0x650 net/core/dev.c:5739 netif_receive_skb_internal net/core/dev.c:5825 [inline] netif_receive_skb+0x1e8/0x890 net/core/dev.c:5885 tun_rx_batched+0x1b7/0x8f0 drivers/net/tun.c:1549 tun_get_user+0x2f35/0x4560 drivers/net/tun.c:2002 tun_chr_write_iter+0x113/0x1f0 drivers/net/tun.c:2048 call_write_iter include/linux/fs.h:2110 [inline] new_sync_write fs/read_write.c:497 [inline] vfs_write+0xa84/0xcb0 fs/read_write.c:590 ksys_write+0x1a0/0x2c0 fs/read_write.c:643 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf5/0x240 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f Fixes: 3e140491 ("mptcp: support rstreason for passive reset") Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
Matthieu Baerts (NGI0) <matttbe@kernel.org> Reviewed-by:
Jason Xing <kerneljasonxing@gmail.com> Link: https://lore.kernel.org/r/20240506123032.3351895-1-edumazet@google.comSigned-off-by:
-
Florian Westphal authored
Netdev CI reports occasional failures with this test ("ERROR: ns2-dX6bUE did not pick up tcp connection from peer"). Add explicit busywait call until the initial connection attempt shows up in conntrack rather than a one-shot 'must exist' check. Signed-off-by:Florian Westphal <fw@strlen.de> Link: https://lore.kernel.org/r/20240506114320.12178-1-fw@strlen.deSigned-off-by:
-
Eric Dumazet authored
Simon reported that ndo_change_mtu() methods were never updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted in commit 501a90c9 ("inet: protect against too small mtu values.") We read dev->mtu without holding RTNL in many places, with READ_ONCE() annotations. It is time to take care of ndo_change_mtu() methods to use corresponding WRITE_ONCE() Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Reviewed-by:
Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Shannon Nelson <shannon.nelson@amd.com> Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.comSigned-off-by:
-
Jeff Johnson authored
make C=1 reports: warning: Function parameter or struct member 'mrtt' not described in 'ccid2_rtt_estimator' So document the 'mrtt' parameter. Signed-off-by:
Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by:
-
Matthias Schiffer authored
The embedded PHYs of the 88E6250 family switches are very basic - they do not even have an Extended Address / Page register. This adds support for the PHYs to the driver to set up PHY interrupts and retrieve error stats. To deal with PHYs without a page register, "simple" variants of all stat handling functions are introduced. The code should work with all 88E6250 family switches (6250/6220/6071/ 6070/6020). The PHY ID 0x01410db0 was read from a 88E6020, under the assumption that all switches of this family use the same ID. The spec only lists the prefix 0x01410c00 and leaves the last 10 bits as reserved, but that seems too unspecific to be useful, as it would cover several existing PHY IDs already supported by the driver; therefore, the ID read from the actual hardware is used. Signed-off-by:
Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by:
-
Matthias Schiffer authored
The list of stat registers is read-only, so we can declare it as const. Signed-off-by:
-
Paolo Abeni authored
Daniel Jurgens says: ==================== Remove RTNL lock protection of CVQ Currently the buffer used for control VQ commands is protected by the RTNL lock. Previously this wasn't a major concern because the control VQ was only used during device setup and user interaction. With the recent addition of dynamic interrupt moderation the control VQ may be used frequently during normal operation. This series removes the RNTL lock dependency by introducing a mutex to protect the control buffer and writing SGs to the control VQ. v6: - Rebased over new stats code. - Added comment to cvq_lock, init the mutex unconditionally, and replaced some duplicate code with a goto. - Fixed minor grammer errors, checkpatch warnings, and clarified a comment. v5: - Changed cvq_lock to a mutex. - Changed dim_lock to mutex, because it's held taking the cvq_lock. - Use spin/mutex_lock/unlock vs guard macros. v4: - Protect dim_enabled with same lock as well intr_coal. - Rename intr_coal_lock to dim_lock. - Remove some scoped_guard where the error path doesn't have to be in the lock. v3: - Changed type of _offloads to __virtio16 to fix static analysis warning. - Moved a misplaced hunk to the correct patch. v2: - New patch to only process the provided queue in virtnet_dim_work - New patch to lock per queue rx coalescing structure. ==================== Link: https://lore.kernel.org/r/20240503202445.1415560-1-danielj@nvidia.comSigned-off-by:
-
Daniel Jurgens authored
The rtnl lock is no longer needed to protect the control buffer and command VQ. Signed-off-by:
Daniel Jurgens <danielj@nvidia.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Reviewed-by:
Heng Qi <hengqi@linux.alibaba.com> Tested-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Daniel Jurgens authored
Once the RTNL locking around the control buffer is removed there can be contention on the per queue RX interrupt coalescing data. Use a mutex per queue. A mutex is required because virtnet_send_command can sleep. Signed-off-by:
-
