Change the implementation of wil log functions for consistency
with __wil_dbg_ratelimited.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Adding pm_notify to allow the following:
1. Check if suspend is allowed in an earlier stage to prevent
starting the suspend procedure in case it is not allowed
2. Notify the platform driver on the suspend request
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In case we fail to map one of the TSO SKB fragments, we need to
clear all the mapped descriptors, from swhead to swhead+descs_used-1.

Change the desc index calculation to
i = (swhead + descs_used - 1) % vring->size;
to prevent unmpping of (swhead + descs_used) descriptor that wasn't
mapped.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

napi_synchronize is called before releasing the vring, with the
assumption that setting txdata->enabled to 0 will prevent handling
of this vring in the next scheduled napi.
To guarantee this assumption, a memory barrier is added after disabling
the txdata.
In addition, as the ctx is zeroed in wil_tx_complete after this
descriptor is handled (protected by wmb), ctx needs to be checked
before releasing this descriptor in wil_vring_free.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

add memory barrier after allocating new rx descriptors, before
updating the hwtail.
This will guarantee that all writes to descriptors (shared memory)
are done before committing them to HW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There are 2 possible race conditions, both are solved by addition of
memory barrier:
1. wil_tx_complete reads the swhead to determine if the vring is
empty. In case the swhead was updated before the descriptor update
was performed in __wil_tx_vring/__wil_tx_vring_tso, the completion
loop will not end and as the DU bit may still be set from a previous
run, this skb can be handled as completed before it was sent, which
will lead to double free of the same SKB.
2. __wil_tx_vring/__wil_tx_vring_tso calculate the number of available
descriptors according to the swtail. In case the swtail is updated
before memset of ctx to zero is completed, we can handle this
descriptor while later on ctx is zeroed.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

As there is current support for ar9002 tx99 mode, just allow
to init debugfs and enable tx99.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Just some code cleanup to remove an empty if clause.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Legacy rate packets may not necessarily be having a rx status
flag of '0' always, for example management frame have flags
like RX_FLAG_ONLY_MONITOR / RX_FLAG_MACTIME_END also set

Just check 'VHT' and 'HT' flags are not set , and simply clasify it as
legacy rate packets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

WARN_ON_ONCE when we receive packets for self peer when mac80211
had not assigned a proper channel context. This scenario happens
in QCA4019 when we start the AP via hostapd in background and start
it once again in the background without killing the previous instance!
This happens intermittently when we start / stop hostapd in a while loop
(incase the hostapd is not properly killed).  This results in mac80211
chancontext to be unassigned, while the self peer continuous receive
packets in target operating channel. This results in lot of call traces
in the rx path. Make this as a WARN_ON_ONCE to avoid flooding the console
which result in rebooting low memory systems, while still reporting the
warning once that we are receiving packets in target operating channel and
to indicate that something is happening which is not the expected result.

WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Recent changes revolving around implementing
wake_tx_queue support introduced a significant
performance regressions on some (slower, uni-proc)
systems.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

QCA9984 shares the same configuration with QCA99X0.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

QCA9984 Rx descriptor has two 32-bit words of location information
when compared to one 32-bit word in QCA99X0. To handle this difference in
rx descriptor ppdu_end, define a new ppdu_end for QCA9984 descriptor
which has the new structure to represent rx_location_info.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Store pci chip secific reset funtions in struct ath10k_pci
as callbacks during early ath10k_pci_probe() and use the
callback to perform chip specific resets. This patch essentially
adds two callback in ath10k_pci, one for doing soft reset and
the other for hard reset. By using callbacks we can get rid of
those hw revision checks in ath10k_pci_safe_chip_reset() and
ath10k_pci_chip_reset(). As such this patch does not fix
any issue.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Define rx_location_info in struct rx_ppdu_end_qca99x0 after
rx_pkt_end. This is to prepare rx_ppdu_end for QCA9984 chip.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath.git patches for 4.7. Major changes:

ath6kl

* add ability to set debug uart baud rate with a module parameter

wil6210

* add debugfs file to configure firmware led functionality

In QCA4019, cycle counter wraparound in same fashion
as QCA988X. When the cycle counter wraparound it
resets to 0x7fffffff. Set has_shifted_cc_wraparound to
true for QCA4019 to enable the code path to handle cycle
counter wraparound for consistent survey report.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In 10.4, fw sends WMI PEER_RATECODE_LIST_EVENTID after successful
peer_assoc cmd. As of now this event is not of much use and not
implemented. Change the debug level and messsage as appropriate
to suppress "Unknown eventid: 36898".
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add the ability to configure the device led to be used for notifying
the AP activity (60G device supports leds 0-2).
The host can also configure the blinking frequency of the led in
three states.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Smatch complains that we cap the upper bound of "fwrq->m" but not the
lower bound.  I don't know if it can actually happen but it's simple
enough to check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

I'm not sure if this can underflow but Smatch complains.  It seems
harmless to add a check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use dev_err instead of pr_err and add newline character at the end.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We can't use kfree_skb in irq disable context, because spin_lock_irqsave
make sure we are always in irq disable context, use dev_kfree_skb_irq
instead of kfree_skb is better than dev_kfree_skb_any.

This patch fix below kernel warning:
[ 7612.095528] ------------[ cut here ]------------
[ 7612.095546] WARNING: CPU: 3 PID: 4460 at kernel/softirq.c:150 __local_bh_enable_ip+0x58/0x80()
[ 7612.095550] Modules linked in: rtl8723be x86_pkg_temp_thermal btcoexist rtl_pci rtlwifi rtl8723_common
[ 7612.095567] CPU: 3 PID: 4460 Comm: ifconfig Tainted: G        W       4.4.0+ #4
[ 7612.095570] Hardware name: LENOVO 20DFA04FCD/20DFA04FCD, BIOS J5ET48WW (1.19 ) 08/27/2015
[ 7612.095574]  00000000 00000000 da37fc70 c12ce7c5 00000000 da37fca0 c104cc59 c19d4454
[ 7612.095584]  00000003 0000116c c19d4784 00000096 c10508a8 c10508a8 00000200 c1b42400
[ 7612.095594]  f29be780 da37fcb0 c104ccad 00000009 00000000 da37fcbc c10508a8 f21f08b8
[ 7612.095604] Call Trace:
[ 7612.095614]  [<c12ce7c5>] dump_stack+0x41/0x5c
[ 7612.095620]  [<c104cc59>] warn_slowpath_common+0x89/0xc0
[ 7612.095628]  [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80
[ 7612.095634]  [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80
[ 7612.095640]  [<c104ccad>] warn_slowpath_null+0x1d/0x20
[ 7612.095646]  [<c10508a8>] __local_bh_enable_ip+0x58/0x80
[ 7612.095653]  [<c16b7d34>] destroy_conntrack+0x64/0xa0
[ 7612.095660]  [<c16b300f>] nf_conntrack_destroy+0xf/0x20
[ 7612.095665]  [<c1677565>] skb_release_head_state+0x55/0xa0
[ 7612.095670]  [<c16775bb>] skb_release_all+0xb/0x20
[ 7612.095674]  [<c167760b>] __kfree_skb+0xb/0x60
[ 7612.095679]  [<c16776f0>] kfree_skb+0x30/0x70
[ 7612.095686]  [<f81b869d>] ? rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci]
[ 7612.095692]  [<f81b869d>] rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci]
[ 7612.095698]  [<f81b87f9>] rtl_pci_start+0x19/0x190 [rtl_pci]
[ 7612.095705]  [<f81970e6>] rtl_op_start+0x56/0x90 [rtlwifi]
[ 7612.095712]  [<c17e3f16>] drv_start+0x36/0xc0
[ 7612.095717]  [<c17f5ab3>] ieee80211_do_open+0x2d3/0x890
[ 7612.095725]  [<c16820fe>] ? call_netdevice_notifiers_info+0x2e/0x60
[ 7612.095730]  [<c17f60bd>] ieee80211_open+0x4d/0x50
[ 7612.095736]  [<c16891b3>] __dev_open+0xa3/0x130
[ 7612.095742]  [<c183fa53>] ? _raw_spin_unlock_bh+0x13/0x20
[ 7612.095748]  [<c1689499>] __dev_change_flags+0x89/0x140
[ 7612.095753]  [<c127c70d>] ? selinux_capable+0xd/0x10
[ 7612.095759]  [<c1689589>] dev_change_flags+0x29/0x60
[ 7612.095765]  [<c1700b93>] devinet_ioctl+0x553/0x670
[ 7612.095772]  [<c12db758>] ? _copy_to_user+0x28/0x40
[ 7612.095777]  [<c17018b5>] inet_ioctl+0x85/0xb0
[ 7612.095783]  [<c166e647>] sock_ioctl+0x67/0x260
[ 7612.095788]  [<c166e5e0>] ? sock_fasync+0x80/0x80
[ 7612.095795]  [<c115c99b>] do_vfs_ioctl+0x6b/0x550
[ 7612.095800]  [<c127c812>] ? selinux_file_ioctl+0x102/0x1e0
[ 7612.095807]  [<c10a8914>] ? timekeeping_suspend+0x294/0x320
[ 7612.095813]  [<c10a256a>] ? __hrtimer_run_queues+0x14a/0x210
[ 7612.095820]  [<c1276e24>] ? security_file_ioctl+0x34/0x50
[ 7612.095827]  [<c115cef0>] SyS_ioctl+0x70/0x80
[ 7612.095832]  [<c1001804>] do_fast_syscall_32+0x84/0x120
[ 7612.095839]  [<c183ff91>] sysenter_past_esp+0x36/0x55
[ 7612.095844] ---[ end trace 97e9c637a20e8348 ]---
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtl_lps_enter does two successive check for cnt_after_linked
to make sure some time has elapsed after linked. The second
check isn't necessary, because if cnt_after_linked is bigger
than 5, it is bigger than 2 of course!

This patch remove the second check code.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This adds support for the 4356-sdio wireless chip.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

What about if "rtlphy->pwrgroup_cnt" is 2?  In that case we would use an
uninitialized "chnlgroup" variable and probably crash.  Maybe that can't
happen for some reason which is not obvious but in that case this patch
is harmless.

Setting it to zero seems like a standard default in the surrounding code
so it's probably fine here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This header file is only needed for drivers binding to a PCI bridge
device allocated by drivers/pci/pcie/portdrv_core.c. The mwifiex driver
doesn't do that nor use any symbols defined in pcieport_if.h.

Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.

Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Signed-off-by: Wang YanQing <udknight@gmail.com>
CC: Stable <stable@vger.kernel.org> [3.10+]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The rtl_intf_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The commit fb724ed5 ("wlcore: Fix regression in
wlcore_set_partition()") fixed wl12xx functionality.
However, it reverted the support in fw logger
over sdio in wl18xx.

This patch reverts the changes made and also fixes
the original functionality issue introduced in wl12xx.

Fixes: fb724ed5 ("wlcore: Fix regression in wlcore_set_partition()")
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2016-05-10' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* work for RX multiqueue continues (Sara);
* dynamic queue allocation work continues (Liad);
* add Luca as maintainer;
* a bunch of fixes and improvements all over;

I'm starting to take a more active role in the iwlwifi driver
maintainership.

Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Small change to make it clear that the default value is false.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When initializing RX we grab NIC access for every read and
write. This is redundant - we can just grab access once.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The RX queues have a shadow register for the write pointer
that enables updates without grabbing NIC access. Use them
instead of the periphery registers because accessing those
is much more expensive.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In non-shared queues, DQA requires re-configuring existing
queues to become aggregated rather than allocating a new
one. It also requires "un-aggregating" an existing queue
when aggregations are turned off.

Support this requirement for non-shared queues.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Since msleep is based on jiffies, it can sleep for a long time.
Use usleep_range() instead to shorten the maximum time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Newer hardware generations will take longer to be accessible again
after reset, so we need to wait longer before continuing any flow
that did a reset.

Rather than make the wait time configurable, simply extend it for
all.

Since all of these code paths can sleep, use usleep_range() rather
than mdelay().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Devices supporting VHT 160MHz width are supporting also Short GI.
Turn on this capability in vht cap.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Since we have a lot of configuration structs (almost 70) saving
some memory in each one of them leads to an overall saving of
~2.6KiB of memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>