Documentation fix
base.c:
  Switched lingering structure field initialiser to ISO C
  Added locking when updating FCB flags

into atnf.csiro.au:/workaholix1/kernel/v2.5/rgooch-2.5

into home.transmeta.com:/home/torvalds/v2.5/linux

Keep the partition information around for the lifetime of the module.

This updates AFS mtd partition parsing to the current CVS version:
- Don't recognise the AFS SIB as a partition
- Ensure initialisation of afs mtdpart structures.

We removed asm/mach-types.h from asm/hardware.h.  This means we must
now include asm/mach-types.h where its used.

We also fix h3600 pcmcia initialisation/cleanup.

Traditionally, the Assabet reverses its mapping of UART1 and UART3
when the Neponset board is connected.  This can be (a) confusing
and (b) annoying when the boot loader uses UART1.  We therefore
have a fixed mapping between the ttySA names and the physical
UARTs on this platform.

The patches convert drivers/pcmcia to use C99 named initializers,
and all the patches are against 2.5.42. There are 25 patches in
total, and the "cat"ing them together they're more that 20K, so
I'm sending the patches as a compressed attachment. The patches
were CC'd to Linus in the first mail that bounced.

Here's a small set of patches that switch the code to use C99
desiginated initializers. Patches are against 2.5.42.

Prevent the assembler putting constant pools in the middle of code.
Clean up shark ISA PIC handling.

This cset removes the global irq handling in the AcornSCSI driver,
and makes the target type for bitops an unsigned long array rather
than an unsigned char array.

Remove unnecessary use of __inline__, and remove a few unnecessary
prototypes.  copy_buffer is moved before use.

This removes a compilation warning and makes the code smaller.
It is also more obvious what's going on.

The USB gadget code now lives in arch/arm/mach-sa1100/usb, and
isn't in a mergable state.  We remove the old makefile entries
which are never going to be satisfied, and leave a placeholder for
the usb directory.

dump_stack() got used by the generic code.  Call our version
__dump_stack since we're running out of other descriptive names.
Allow show_trace_task to show the backtrace for the current
thread.

Add rudimentary support for Thumb ptracing; we aren't able to single
step through thumb branches yet, but this change provides enough
infrastructure to make this possible.

This cset updates (as much as is possible) the NCR5380-based Acorn
SCSI drivers, mainly converting them to the new error handling code.
However, they still don't build due to errors in NCR5380.

Vojtech has patches that bring their counterparts in the input
subsystem up to date (and into a working state) so these drivers
are no longer required.

This cset also fixes the Acorn i2c RTC code.

This cset combines the Atomwide and The Serial Port 16550 driver
modules into one "8250_acorn.c" driver.  This new module takes full
advantage of the LDM-based expansion card facilities.

This cset implements validity checks on the ethernet MAC address when
the device is opened, and refuses to open the device if this check
fails.  We also provide the set_mac_address method to allow ifconfig
to change the mac address to something valid.

In addition, the driver is converted from the old expansion card
discovery methods to the new device model driver framework.

Provide LDM-based driver registration/removal interface for drivers
to use.  We make the old device discovery code ignore devices
claimed via the LDM framework.  However, the LDM framework ignores
devices that may be in use by the old device discovery code.  This
is fine since the only devices that will still use the old discovery
code will be SCSI drivers.

Currently, we don't provide a useful dev.name entry.

This updates the Integrator cpufreq code to use the new interfaces,
and makes the sa1100 cpufreq round up the requested frequency.

The second serial port is never present in these machines, so its
pointless listing it in the first place.

- ide_register_hw takes two arguments, not one.
- ide_fix_driveid is no longer used.

This adds ARM support for in_atomic() and asm/numnodes.h

This updates these neponset and sa1111 support to use the new system
device infrastructure in the Linux device model.

Sanitise includes of asm/tlbflush.h, asm/cacheflush.h, asm/proc-fns.h
Implement ARM-specific TLB "shootdown" code.  It turns out that it
is overall more efficient to unconditionally invalidate the whole
TLB rather than entry by entry when removing areas.

This cset fixes the RiscPC decompressor code for the PIC changes.

We use a pointer to a structure rather than a structure to access
params.  With a PIC decompressor, the address of the structure gets
PIC-ified which is not what we want.

Update pcibios_enable_device to only enable requested resources,
mainly for IDE.  Supply a pci_mmap_page_range() function to allow
user space to mmap PCI regions.

This updates the ARM time keeping functions to use tick_nsec/1000
instead of tick.

To keep the Config.in files relatively clean, we use the
following construct:

 if [ "$CONFIG_ARM" = "y" ]; then
    dep_tristate 'Foo' CONFIG_FOO $CONFIG_BAR
 fi

where CONFIG_BAR is some machine implementation or high-level
chip support configuration option.  If CONFIG_BAR is left
empty, then the tristate is offered to the user, which isn't
what we want.  Defining CONFIG_BAR to 'n' prevents the option
being offered.

This is a rule I generally try to implement within
arch/arm/config.in.

This cset makes CONFIG_SA1111 and CONFIG_ARM_THUMB behave that
way.