- 23 Sep, 2016 10 commits
-
-
Lihong Yang authored
The i40e_shutdown_adminq function never returns failure. There is no need to check the non-0 return value. Clean up the unnecessary error checking and warning against it. Change-ID: Ibb616f09cfb93bd1a872ebf3241a15fb8354b31b Signed-off-by:
Lihong Yang <lihong.yang@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Alexander Duyck authored
The i40e driver was incorrectly assuming that we would always be pulling no more than 1 descriptor from each fragment. It is in fact possible for us to end up with the case where 2 descriptors worth of data may be pulled when a frame is larger than one of the pieces generated when aligning the payload to either 4K or pieces smaller than 16K. To adjust for this we just need to make certain to test all the way to the end of the fragments as it is possible for us to span 2 descriptors in the block before us so we need to guarantee that even the last 6 descriptors have enough data to fill a full frame. Change-ID: Ic2ecb4d6b745f447d334e66c14002152f50e2f99 Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Tested-by:
-
Bimmy Pujari authored
Function i40evf_up_complete() always returns success. Changed this to a void type and removed the code that checks the return status and prints an error message. Change-ID: I8c400f174786b9c855f679e470f35af292fb50ad Signed-off-by:
Bimmy Pujari <bimmy.pujari@intel.com> Tested-by:
-
Sridhar Samudrala authored
Currently disabling the link state from PF via ip link set enp5s0f0 vf 0 state disable doesn't disable the CARRIER on the VF. This patch updates the carrier and starts/stops the tx queues based on the link state notification from PF. PF: enp5s0f0, VF: enp5s2 #modprobe i40e #echo 2 > /sys/class/net/enp5s0f0/device/sriov_numvfs #ip link set enp5s2 up #ip -d link show enp5s2 175: enp5s2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether ea:4d:60:bc:6f:85 brd ff:ff:ff:ff:ff:ff promiscuity 0 addrgenmode eui64 #ip link set enp5s0f0 vf 0 state disable #ip -d link show enp5s0f0 171: enp5s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 68:05:ca:2e:72:68 brd ff:ff:ff:ff:ff:ff promiscuity 0 addrgenmode eui64 numtxqueues 72 numrxqueues 72 portid 6805ca2e7268 vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state disable, trust off vf 1 MAC 00:00:00:00:00:00, spoof checking on, link-state auto, trust off #ip -d link show enp5s2 175: enp5s2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000 link/ether ea:4d:60:bc:6f:85 brd ff:ff:ff:ff:ff:ff promiscuity 0 addrgenmode eui64 numtxqueues 16 numrxqueues 16 Signed-off-by:Sridhar Samudrala <sridhar.samudrala@intel.com> Tested-by:
-
Colin Ian King authored
There is a sanitcy check for desc being null in the first line of function i40evf_debug_aq. However, before that, aq_desc is cast from desc, and aq_desc is being dereferenced on the assignment of len, so this could be a potential null pointer deference. Fix this by moving the initialization of len to the code block where len is being used and hence at this point we know it is OK to dereference aq_desc. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Tested-by:
-
Carolyn Wyborny authored
This patch fixes an issue where we were byte swapping the port parameter, then byte swapping it again in function execution. Obviously, that's unnecessary, so take it out of the function calls. Without this patch, the udp based tunnel configuration would not be correct. Change-ID: I788d83c5bd5732170f1a81dbfa0b1ac3ca8ea5b7 Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
-
Carolyn Wyborny authored
This patch fixes an issue in the virt channel code, where a return from i40e_find_vsi_from_id was not checked for NULL when applicable. Without this patch, there is a risk for panic and static analysis tools complain. This patch fixes the problem by adding the check and adding an additional input check for similar reasons. Change-ID: I7e9be88eb7a3addb50eadc451c8336d9e06f5394 Signed-off-by:
-
Mitch Williams authored
This conditional is backward, so the driver responds back to the VF with the wrong opcode. Do the old switcheroo to fix this. Change-ID: I384035b0fef8a3881c176de4b4672009b3400b25 Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Alan Brady authored
When using the debugfs to issue the "dump port" command with NPAR enabled, the firmware reports back with invalid argument. The issue occurs because the pf->mac_seid was used to perform the query. This is fine when NPAR is disabled because the switch ID == pf->mac_seid, however this is not the case when NPAR is enabled. This fix instead goes through the VSI to determine the correct ID to use in either case. Change-ID: I0cd67913a7f2c4a2962e06d39e32e7447cc55b6a Signed-off-by:
Alan Brady <alan.brady@intel.com> Tested-by:
-
Alan Brady authored
Previously, when using ethtool to change the RSS hash key, ethtool would report back saying the old key was still being used and no error was reported. It was unclear whether it was being reported incorrectly or being set incorrectly. Debugging revealed 'i40e_set_rxfh()' returned zero immediately instead of setting the key because a user defined indirection table is not supplied when changing the hash key. This fix instead changes it such that if an indirection table is not supplied, then a default one is created and the hash key is now correctly set. Change-ID: Iddb621897ecf208650272b7ee46702cad7b69a71 Signed-off-by:
-
- 22 Sep, 2016 30 commits
-
-
David S. Miller authored
Joel Stanley says: ==================== ftgmac100 support for ast2500 This series adds support to the ftgmac100 driver for the Aspeed ast2400 and ast2500 SoCs. In particular, they ensure the driver works correctly on the ast2500 where the MAC block has seen some changes in register layout. They have been tested on ast2400 and ast2500 systems with the NCSI stack and with a directly attached PHY. V2 reworks the two patches relating to PHYSTS_CHG into the one patch that disables the interrupt instead of playing with interrupt sensitivity. I kept patch 4 'net/faraday: Clear stale interrupts' which was first introduced to clear the stale PHYSTS_CHG interrupt, as it helps keep us safe from unhygienic (vendor) bootloaders. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Joel Stanley authored
The PHYSTS_CHG (the ftgmac100's PHY IRQ) is telling the system to go look at the PHY registers for a link status change. The interrupt was causing issues on Aspeed SoC where some board designs had an active high configuration, some active low, and in some cases repurposed for other functions. When misconfigured Linux would chew 100% of CPU cycles servicing interrupts: [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.280000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG [ 20.300000] ftgmac100 1e660000.ethernet eth0: [ISR] = 0x200: PHYSTS_CHG While in the ftgmac100 IP can be configured for high, low and edge sensitivity the current driver always polls the PHY, so we chose to mask out the interrupt. See https://patchwork.ozlabs.org/patch/672099/ for more discussion. Signed-off-by:
Joel Stanley <joel@jms.id.au> Signed-off-by:
-
Joel Stanley authored
The Aspeed SoCs have a new MDIO interface as an option in the G4 and G5 SoCs. The old one is still available, so select it in order to remain compatible with the ftgmac100 driver. Signed-off-by:
-
Gavin Shan authored
There is stale interrupt (PHYSTS_CHG in ISR, bit#6 in 0x0) from the bootloader (uboot) when enabling the MAC. The stale interrupts aren't part of kernel and should be cleared. This clears the stale interrupts in ISR (0x0) when enabling the MAC. Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
-
Joel Stanley authored
The RXDES and TXDES registers bits in the ftgmac100 indicates EDO{R,T}R at bit position 15 for the Faraday Tech IP. However, the version of this IP present in the Aspeed SoCs has these bits at position 30 in the registers. It appers that ast2400 SoCs support both positions, with the 15th bit marked as reserved but still functional. In the ast2500 this bit is reused for another function, so we need a work around. This was confirmed with engineers from Aspeed that using bit 30 is correct for both the ast2400 and ast2500 SoCs. Signed-off-by: -
Andrew Jeffery authored
These bits are #defined at a fixed location. In order to support future hardware that has chosen to move these bits around move the bits into a member of the struct ftgmac100. Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Signed-off-by:
-
Andrew Jeffery authored
The ftgmac100 hardware revision in e.g. the Aspeed AST2500 no longer reserves all bits in RXDES#2 but instead uses the bottom 16 bits to store MAC frame metadata. Avoid corruption by shifting struct page pointers out to their own member in struct ftgmac100. Signed-off-by:
-
Wei Yongjun authored
Remove an open coded simple_open() function and replace file operations references to the function with simple_open() instead. Generated by: scripts/coccinelle/api/simple_open.cocci Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Wei Yongjun authored
mdio_module_driver() makes the code simpler by eliminating boilerplate code. Signed-off-by:
-
Wei Yongjun authored
Fixes the following sparse warning: drivers/net/dsa/qca8k.c:259:22: warning: symbol 'qca8k_regmap_config' was not declared. Should it be static? Signed-off-by:
-
David S. Miller authored
Marcelo Ricardo Leitner says: ==================== Rename WORD_TRUNC/ROUND macros and use them This patchset aims to rename these macros to a non-confusing name, as reported by David Laight and David Miller, and to update all remaining places to make use of it, which was 1 last remaining spot. v3: - Name it SCTP_PAD4 instead of SCTP_ALIGN4, as suggested by David Laight v2: - fixed 2nd patch summary Details on the specific changelogs. ==================== Signed-off-by: -
Marcelo Ricardo Leitner authored
And avoid the usage of '&~3'. This is the last place still not using the macro. Also break the line to make it easier to read. Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Marcelo Ricardo Leitner authored
To something more meaningful these days, specially because this is working on packet headers or lengths and which are not tied to any CPU arch but to the protocol itself. So, WORD_TRUNC becomes SCTP_TRUNC4 and WORD_ROUND becomes SCTP_PAD4. Reported-by:
David Laight <David.Laight@ACULAB.COM> Reported-by:
-
David S. Miller authored
Tariq Toukan says: ==================== mlx5e XDP support This series adds XDP support in mlx5e driver. This includes the use cases: XDP_DROP, XDP_PASS, and XDP_TX. Single stream performance tests show 16.5 Mpps for XDP_DROP, and 12.4 Mpps for XDP_TX, with nice scalability for multiple streams/rings. This rate of XDP_DROP is lower than the 32 Mpps we got in previous implementation, when Striding RQ was used. We moved to non-Striding RQ, as some XDP_TX requirements (like headroom, packet-per-page) cannot be satisfied with the current Striding RQ HW, and we decided to fully support both DROP/TX. Few directions are considered in order to enable the faster rate for XDP_DROP, e.g a possibility for users to enable Striding RQ so they choose optimized XDP_DROP on the price of partial XDP_TX functionality, or some HW changes. Series generated against net-next commit: cf714ac1 'ipvlan: Fix dependency issue' Thanks, Tariq V2: * patch 8: - when XDP_TX fails, call mlx5e_page_release and drop the packet. - update xdp_tx counter within mlx5e_xmit_xdp_frame. (mlx5e_xmit_xdp_frame return value becomes obsolete, change it to void) - drop the packet for unknown XDP return code. * patch 9: - use a boolean for xdp_doorbell in SQ struct, instead of dragging it throughout the functions calls. - handle doorbell and counters within mlx5e_xmit_xdp_frame. ==================== Signed-off-by:
-
Saeed Mahameed authored
Previously we rang XDP SQ doorbell on every forwarded XDP packet. Here we introduce a xmit more like mechanism that will queue up more than one packet into SQ (up to RX napi budget) w/o notifying the hardware. Once RX napi budget is consumed and we exit napi RX loop, we will flush (doorbell) all XDP looped packets in case there are such. XDP forward packet rate: Comparing XDP with and w/o xmit more (bulk transmit): RX Cores XDP TX XDP TX (xmit more) --------------------------------------------------- 1 6.5Mpps 12.4Mpps 2 13.2Mpps 24.2Mpps 4 25.2Mpps 36.3Mpps* 8 36.3Mpps* 36.3Mpps* *My xmitter was limited to 36.3Mpps, so it is the bottleneck. It seems that receive side can handle more. Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Saeed Mahameed authored
Adding support for XDP_TX forwarding from xdp program. Using XDP, now user can loop packets out of the same port. We create a dedicated TX SQ for each channel that will serve XDP programs that return XDP_TX action to loop packets back to the wire directly from the channel RQ RX path. For that RX pages will now need to be mapped bi-directionally, and on XDP_TX action we will sync the page back to device then queue it into SQ for transmission. The XDP xmit frame function will report back to the RX path if the page was consumed (transmitted), if so, RX path will forget about that page as if it were released to the stack. Later on, on XDP TX completion, the page will be released back to the page cache. For simplicity this patch will hit a doorbell on every XDP TX packet. Next patch will introduce a xmit more like mechanism that will queue up more than one packet into SQ w/o notifying the hardware, once RX napi loop is done we will hit doorbell once for all XDP TX packets form the previous loop. This should drastically improve XDP TX performance. Signed-off-by:
-
Saeed Mahameed authored
Make a clear separate between Regular SQ (TXQ) and ICO SQ creation, destruction and union their mutual information structures. Don't allocate redundant TXQ skb/wqe_info/dma_fifo arrays for ICO SQ. And have a different SQ edge for ICO SQ than TXQ SQ, to be more accurate. In preparation for XDP TX support. Signed-off-by:
-
Rana Shahout authored
Add support for the BPF_PROG_TYPE_PHYS_DEV hook in mlx5e driver. When XDP is on we make sure to change channels RQs type to MLX5_WQ_TYPE_LINKED_LIST rather than "striding RQ" type to ensure "page per packet". On XDP set, we fail if HW LRO is set and request from user to turn it off. Since on ConnectX4-LX HW LRO is always on by default, this will be annoying, but we prefer not to enforce LRO off from XDP set function. Full channels reset (close/open) is required only when setting XDP on/off. When XDP set is called just to exchange programs, we will update each RQ xdp program on the fly and for synchronization with current data path RX activity of that RQ, we temporally disable that RQ and ensure RX path is not running, quickly update and re-enable that RQ, for that we do: - rq.state = disabled - napi_synnchronize - xchg(rq->xdp_prg) - rq.state = enabled - napi_schedule // Just in case we've missed an IRQ Packet rate performance testing was done with pktgen 64B packets and on TX side and, TC drop action on RX side compared to XDP fast drop. CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz Comparison is done between: 1. Baseline, Before this patch with TC drop action 2. This patch with TC drop action 3. This patch with XDP RX fast drop RX Cores Baseline(TC drop) TC drop XDP fast Drop -------------------------------------------------------------- 1 5.3Mpps 5.3Mpps 16.5Mpps 2 10.2Mpps 10.2Mpps 31.3Mpps 4 20.5Mpps 19.9Mpps 36.3Mpps* *My xmitter was limited to 36.3Mpps, so it is the bottleneck. It seems that receive side can handle more. Signed-off-by:
Rana Shahout <ranas@mellanox.com> Signed-off-by:
-
Saeed Mahameed authored
Add two helper functions to allow dynamic changes of RQ type. mlx5e_set_rq_priv_params and mlx5e_set_rq_type_params will be used on netdev creation to determine the default RQ type. This will be needed later for downstream patches of XDP support. When enabling XDP we will dynamically move from striding RQ to linked list RQ type. Signed-off-by:
-
Saeed Mahameed authored
Before this patch LRO size was 64K, now with build_skb requires extra room, headroom + sizeof(skb_shared_info) added to the data buffer will make wqe size or page_frag_size slightly larger than 64K which will demand order 5 page instead of order 4 in 4K page systems. We take those extra bytes from hardware LRO data size in order to not increase the required page order for when hardware LRO is enabled. Signed-off-by:
-
Saeed Mahameed authored
We have two types of RX RQs, and they use two separate sets of info arrays and structures in RX data path function. Today those structures are mutually exclusive per RQ type, hence one kind is allocated on RQ creation according to the RQ type. For better cache locality and to minimalize the sizeof(struct mlx5e_rq), in this patch we define them as a union. Signed-off-by:
-
Saeed Mahameed authored
For non-striding RQ configuration before this patch we had a ring with pre-allocated SKBs and mapped the SKB->data buffers for device. For robustness and better RX data buffers management, we allocate a page per packet and build_skb around it. This patch (which is a prerequisite for XDP) will actually reduce performance for normal stack usage, because we are now hitting a bottleneck in the page allocator. We use the page-cache to restore or even improve performance in comparison to the old RX scheme. Packet rate performance testing was done with pktgen 64B packets on xmit side and TC ingress dropping action on RX side. CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz Comparison is done between: 1.Baseline, before 'net/mlx5e: Build RX SKB on demand' 2.Build SKB with RX page cache (This patch) RX Cores Baseline Build SKB+page-cache Improvement ----------------------------------------------------------- 1 4.16Mpps 5.33Mpps 28% 2 7.16Mpps 10.24Mpps 43% 4 13.61Mpps 20.51Mpps 51% 8 25.32Mpps 32.00Mpps 26% All respective cores were 100% utilized. Signed-off-by:
-
Eric Dumazet authored
We saw sch_fq drops caused by the per flow limit of 100 packets and TCP when dealing with large cwnd and bursts of retransmits. Even after increasing the limit to 1000, and even after commit 10d3be56 ("tcp-tso: do not split TSO packets at retransmit time"), we can still have these drops. Under certain conditions, TCP can spend a considerable amount of time queuing thousands of skbs in a single tcp_xmit_retransmit_queue() invocation, incurring latency spikes and stalls of other softirq handlers. This patch implements TSQ for retransmits, limiting number of packets and giving more chance for scheduling packets in both ways. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== Preparation for mv88e6390 These two patches are a couple of preparation steps for supporting the the MV88E6390 family of chips. This is a new generation from Marvell, and will need more feature flags than are currently available in an unsigned long. Expand to an unsigned long long. The MV88E6390 also places its port registers somewhere else, so add a wrapper around port register access. v2: Rework wrappers to use mv88e6xxx_{read|write} Simpliy some (err < ) to (err) Add Reviewed by tag. v3:: reg = reg & foo -> reg &= foo Fix over zealous s/ret/err ==================== Signed-off-by: -
Andrew Lunn authored
We are soon going to run out of flag bits on 32bit systems. Convert to unsigned long long. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
Andrew Lunn authored
There is a device coming soon which places its port registers somewhere different to all other Marvell switches supported so far. Add helper functions for reading/writing port registers, making it easier to handle this new device. Signed-off-by:
-
Nicolas Pitre authored
Drivers must be ready to accept NULL from ptp_clock_register() if the PTP clock subsystem is configured out. This patch documents that and ensures that all drivers cope well with a NULL return. Signed-off-by:
Nicolas Pitre <nico@linaro.org> Reviewed-by:
Eugenia Emantayev <eugenia@mellanox.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Acked-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
-
Philippe Reynes authored
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. Signed-off-by:Philippe Reynes <tremyfr@gmail.com> Signed-off-by:
-
Philippe Reynes authored
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by:
-
Sean Wang authored
add the missing commits about 1) Commit d3bd1ce4 ("remove redundant free_irq for devm_request_ir allocated irq") 2) Commit 7c6b0d76 ("fix logic unbalance between probe and remove") during merge for conflicts overlapping commits by Commit b20b378d ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") Signed-off-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
-
