This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port".  This feature is implemented in firmware
and is largely transparent to the driver, except...

It turns out that the UMP firmware needs to know the current status
of the link.  Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.

This patch implements the new handshake with the UMP firmware.  Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully.  This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be.  This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MI clock is not configured correctly on adapters with the CPMU
present.  The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions.  Consequently, the MI will run slow when the
core's clock has been slowed down.

There is a new 500KHz constant frequency clock available on adapters
with a CPMU.  This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.

Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking.  Prevent that from happening
by strategically placed barriers.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Makes the intention of the nested min/max clear.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

WARN_ON_ONCE() gives a stack trace including the full module list.
Having this in the kernel dump for the timeout case in the
generic netdev watchdog will help us see quicker which driver
is involved. It also allows us to collect statistics 
and patterns in terms of which drivers have this event occuring.

Suggested by Andrew Morton
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One finds all kinds of crazy things with some shell pipelining.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this unfortunate case, proc_mkdir_mode wrapper can't be used anymore and
this is no way to reuse proc_create_data due to nlinks assignment. So,
copy the code from proc_mkdir and assign PDE->data at the appropriate
moment.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace proc_net_fops_create with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace create_proc_entry with specially created for this purpose proc_create.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check for PDE->data != NULL becomes useless after the replacement
of proc_net_fops_create with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
proc_atm_dev_ops holds proper referrence.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Additionally, there is no need to assign NULL to PDE->data after creation,
/proc generic has already done this for us.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply replace proc_create and further data assigned with proc_create_data.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.

Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.

Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

All channels should be scanned, including the current channel
when the client is associated.

Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes some TX/RX related locking issues.
With this patch applied, some of the PHY transmission errors are fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/8390.c:37:2: warning: returning void-valued expression
drivers/net/bnx2.c:1635:3: warning: returning void-valued expression
drivers/net/xen-netfront.c:1806:2: warning: returning void-valued expression
net/ipv4/tcp_hybla.c:105:3: warning: returning void-valued expression
net/ipv4/tcp_vegas.c:171:3: warning: returning void-valued expression
net/ipv4/tcp_veno.c:123:3: warning: returning void-valued expression
net/sysctl_net.c:85:2: warning: returning void-valued expression
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

(which is autogenerated by kbuild)
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv6: Compilation fix for compat MCAST_MSFILTER sockopts.

We have a race between fcntl() and close() that can lead to
dnotify_struct inserted into inode's list *after* the last descriptor
had been gone from current->files.

Since that's the only point where dnotify_struct gets evicted, we are
screwed - it will stick around indefinitely.  Even after struct file in
question is gone and freed.  Worse, we can trigger send_sigio() on it at
any later point, which allows to send an arbitrary signal to arbitrary
process if we manage to apply enough memory pressure to get the page
that used to host that struct file and fill it with the right pattern...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

So Ingo finally did figure out why UML broke with this option: UML
passes gcc the -fno-unit-at-a-time flag, and apparently that wreaks
havoc with gcc's inlining.

We could turn off -fno-unit-at-a-time for UML for gcc4+ (which is what
x86 does), but there's bad blood about this whole option, and it does
show that the thing is just fragile as heck.

So let tempers cool, and disable the thing, and we can revisit the
decision later.

Cc: Adrian Bunk <bunk@kernel.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes3: (21 commits)
  x86: numaq fix
  x86: 8K stacks by default
  x86: ioremap ram check fix
  x86: fix HT cpu booting on 32-bit
  x86: optimize inlining off
  x86: CONFIG_X86_ELAN fix
  x86: Kconfig fix
  x86 PAT: fix performance drop for glx, use UC minus for ioremap(), ioremap_nocache() and pci_mmap_page_range()
  x86: use defconfigs from x86/configs/*
  toshiba: use ioremap_cached
  revert: "x86: ioremap(), extend check to all RAM pages"
  x86: don't bother printing compat vdso address
  fix: x86: support for new UV apic
  x86: fix early-BUG message
  x86: iommu_sac_force can become static
  x86: add proper header for reboot_force
  x86 VISWS: build fix
  x86, voyager: fix ioremap_nocache()
  hpet: fix
  x86: unexport kmap_atomic_to_page
  ...

According to Coverity (kudo's to Adrian Bunk), we had one use-before-check
bug in libe libertas driver. This patch fixes this issue.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes operation of dual-PHY (A/B/G) devices.
Do not anounce the A-PHY to mac80211, as that's not supported, yet.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Looks like  5d2cdcd4 ("mac80211: get a
TKIP phase key from skb") got the shifts wrong.

Noticed by sparse:
net/mac80211/tkip.c:234:25: warning: right shift by bigger than source value
net/mac80211/tkip.c:235:25: warning: right shift by bigger than source value
net/mac80211/tkip.c:236:25: warning: right shift by bigger than source value
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>