- 21 Aug, 2016 10 commits
-
-
Don Skidmore authored
This patch adds support for the new copper device X557. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This shouldn't matter as nothing should be attached still to be consisted control MDIO speed for these devices as well. Signed-off-by:
-
Don Skidmore authored
The X557 devices use a different interface to the LED for the port. This patch reflect that change. Signed-off-by:
-
Emil Tantilov authored
Add geneve Rx offload support for x550em_a. The implementation follows the vxlan code with the lower 16 bits of the VXLANCTRL register holding the UDP port for VXLAN and the upper for Geneve. Disabled NFS filters in the RFCTL register which allows us to simplify the check for VXLAN and Geneve packets in ixgbe_rx_checksum(). Removed vxlan from the name of the callback functions and replaced it with udp_tunnel which is more in line with the new API. Signed-off-by:
Emil Tantilov <emil.s.tantilov@intel.com> Tested-by:
-
Emil Tantilov authored
The PF driver was only receiving the first 4 bytes of the MAC due to an incorrect size parameter for ixgbevf_write_msg_read_ack() in ixgbevf_set_rar_vf(). Correct the size by calculating it on a fly for all instances where we call ixgbevf_write_msg_read_ack() Signed-off-by:
-
Veola Nazareth authored
ethtool reports backplane type interfaces as 1000/10000baseT link modes. This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present. Signed-off-by:
Veola Nazareth <veola.nazareth@intel.com> Tested-by:
-
David S. Miller authored
Markus Elfring says: ==================== tun: Fine-tuning for update_filter() A few update suggestions were taken into account from static source code analysis. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Markus Elfring authored
Adjust a jump target according to the Linux coding style convention. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
Markus Elfring authored
Reuse existing functionality from memdup_user() instead of keeping duplicate source code. This issue was detected by using the Coccinelle software. Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 40GbE Intel Wired LAN Driver Updates 2016-08-19 This series contains updates to i40e and i40evf only. Jake provides several patches, first just moves a function to co-locate the two functions related to configuring RSS via the admin queue, which should help in spotting bugs when comparing the two functions. Fixed an issue where commit e69ff813 ("i40e: rework the functions to configure RSS with similar parameters") missed checking whether the seed is NULL before using it and did not use the passed in *lut parameter. Fixed an issue where a previous refactor missed i40e_vsi_config_rss() and the values were being ignored, so checked for the fields and used them instead of default values. Lastly replaced calls to create_singlethread_workqueue() with alloc_workqueue() to provide more control over workqueue creation and allows explicit setting of the desired mode of operation. Mitch adds link speed to log messages and reports speed through ethtool. Carolyn refactors tail bump check and fixes byte ordering problems found when enabling this feature support. Adds support for HMC resources and profile commands for x722 firmware. Heinrich Schuchardt fixes format identifiers from %u to %d since the variable is defined as an integer. Catherine fixes an issue where there was a race condition between the completion of the client open and calls to the client ops, so ensured that client ops are not called until we are sure client is open. Harshitha makes sure that i40e_client_release() does not try to use an adapter pointer which may not be initialized, so make sure it is. Joe Perches fixes the use of the local macro XSTRINGIFY() to use __stringify() instead. Avinash corrects the mutex usage in client_subtask(). Fixed the RDMA client to open again after reset since it is closed during a PF reset. Jeff (me) clean up whitespace issues, where indentation was done inconsistently and with spaces versus tabs. ==================== Signed-off-by:
-
- 20 Aug, 2016 30 commits
-
-
William Tu authored
The patch creates sample code exercising bpf_skb_{set,get}_tunnel_key, and bpf_skb_{set,get}_tunnel_opt for GRE, VXLAN, and GENEVE. A native tunnel device is created in a namespace to interact with a lwtunnel device out of the namespace, with metadata enabled. The bpf_skb_set_* program is attached to tc egress and bpf_skb_get_* is attached to egress qdisc. A ping between two tunnels is used to verify correctness and the result of bpf_skb_get_* printed by bpf_trace_printk. Signed-off-by:William Tu <u9012063@gmail.com> Signed-off-by:
-
Haiyang Zhang authored
The existing code uses busy retry when unable to send out receive completions due to full ring buffer. It also gives up retrying after limit is reached, and causes receive buffer slots not being recycled. This patch implements batching of receive completions. It also prevents dropping receive completions due to full ring buffer. Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
Avinash Dayanand authored
RDMA client is closed during the PF reset and needs to be opened again. Setting the flag so that RDMA client is opened in watchdog() function. Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263 Signed-off-by:
Avinash Dayanand <avinash.dayanand@intel.com> Tested-by:
-
Jeff Kirsher authored
Several defines and code comments were indented with spaces instead of tabs, correct the issue to make indentation consistent. Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c Signed-off-by:
-
Avinash Dayanand authored
Correcting the mutex usage, in client_subtask(), mutex_unlock has to be called just before client_del_instance() since this function opens and later closes the same mutex again. Similarly in client_is_registered removing the mutex since it closes the mutex twice. This is a patch suggested by RDMA team. Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852 Signed-off-by:
-
Joe Perches authored
Use __stringify instead. Signed-off-by:
Joe Perches <joe@perches.com> Tested-by:
-
Harshitha Ramamurthy authored
The function i40e_client_release has a print statement that uses an adapter pointer which is not initialized if a previous if statement is not true. Hence, intialize it in the right place. Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8 Signed-off-by:
Harshitha Ramamurthy <harshitha.ramamurthy@intel.com> Tested-by:
-
Catherine Sullivan authored
We were having a race between the completion of the client open and calls to the client ops so don't call a client op unless we are sure the client is open. Testing Hints: Load IWARP driver and make sure it works as expected. Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b Signed-off-by:
Catherine Sullivan <catherine.sullivan@intel.com> Tested-by:
-
Heinrich Schuchardt authored
i is defined as int but output as %u several times. Adjust the format identifiers. Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by:
-
Carolyn Wyborny authored
This patch adds support for HMC resource and profile cmds for X722 firmware. Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e Signed-off-by:
Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by:
-
Carolyn Wyborny authored
This patch fixes byte ordering problems found when enabling this feature support. Without this patch, the feature will not work correctly. This patch fixes the definitions to have the correct byte order. Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6 Signed-off-by:
-
Carolyn Wyborny authored
This patch refactors tail bump check. Change-ID: Ide0e19171d67d90cb2b06b8dcd4fa791ae120160 Signed-off-by:
-
Mitch Williams authored
The PF driver tells us the link speed, so do something with that information. Add link speed to log messages, and report speed through ethtool. Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882 Signed-off-by:
Mitch Williams <mitch.a.williams@intel.com> Tested-by:
-
Jacob Keller authored
Replace calls to create_singlethread_workqueue instead with alloc_workqueue as is style with other Intel drivers. This provides more control over workqueue creation, and allows explicit setting of the desired mode of operation. It also makes it more obvious that driver name constant is passed to a format "%s". Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
-
Jacob Keller authored
A previous refactor added support to store user configuration for VSIs, so that extra VSIs such as for VMDq can use this information when configuring. Unfortunately the i40e_vsi_config_rss function was missed in this refactor, and the values were being ignored. Fix this by checking for the fields and using those instead of always using the default values. Signed-off-by:
-
Jacob Keller authored
X722 hardware requires using the admin queue to configure RSS. This function was previously re-written in commit e69ff813 ("i40e: rework the functions to configure RSS with similar parameters"). However, the previous refactor did not work correctly for a few reasons (a) it does not check whether seed is NULL before using it, resulting in a NULL pointer dereference [ 402.954721] BUG: unable to handle kernel NULL pointer dereference at (null) [ 402.955568] IP: [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e] [ 402.956402] PGD ad610067 PUD accc0067 PMD 0 [ 402.957235] Oops: 0000 [#1] SMP [ 402.958064] Modules linked in: ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_filter ebtable_ broute bridge stp llc ebtable_nat ebtables ip6table_mangle ip6table_raw ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv 6 ip6table_security ip6table_filter ip6_tables iptable_mangle iptable_raw iptable_nat nf_conntrack_ipv4_ nf_defrag_ipv4_ nf_nat_ip v4_ nf_nat nf_conntrack iptable_security intel_rapl i86_kg_temp_thermal coretemp kvm_intel kvm irqbypass crct10dif_clMl crc32_ pclMl ghash_clMlni_intel iTCO_wdt iTCO_vendor_support shpchp sb_edac dcdbas pcspkr joydev ipmi_devintf wmi edac_core ipmi_ssif acpi_ad acpi_ower_meter ipmi_si ipmi_msghandler mei_me nfsd lpc_ich mei ioatdma tpm_tis auth_rpcgss tpm nfs_acl lockd grace s unrpc ifs nngag200 i2c_algo_bit drm_kms_helper ttm drm iigbe bnx2x i40e dca mdio ptp pps_core libcrc32c fjes crc32c_intel [ 402.965563] CPU: 22 PID: 2461 Conm: ethtool Not tainted 4.6.0-rc7_1.2-ABNidQ+ #20 [ 402.966719] Hardware name: Dell Inc. PowerEdge R720/0C4Y3R, BIOS 2.5.2 01/28/2015 [ 402.967862] task: ffff880219b51dc0 ti: ffff8800b3408000 task.ti: ffff8800b3408000 [ 402.969046] RIP: 0010:[<ffffffffa0090ccf>] [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e] [ 402.970339] RSP: 0018:ffff8800b340ba90 EFLAGS: 00010246 [ 402.971616] RAX: 0000000000000000 RBX: ffff88042ec14000 RCX: 0000000000000200 [ 402.972961] RDX: ffff880428eb9200 RSI: 0000000000000000 RDI: ffff88042ec14000 [ 402.974312] RBP: ffff8800b340baf8 R08: ffff880237ada8f0 R09: ffff880428eb9200 [ 402.975709] R10: ffff880428eb9200 R11: 0000000000000000 R12: ffff88042ec2e000 [ 402.977104] R13: ffff88042ec2e000 R14: ffff88042ec14000 R15: ffff88022ea00800 [ 402.978541] FS: 00007f84fd054700(0000) GS:ffff880237ac0000(0000) knlGS:0000000000000000 [ 402.980003] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 402.981508] CR2: 0000000000000000 CR3: 000000003289e000 CR4: 00000000000406e0 [ 402.983028] Stack: [ 402.984578] 0000000002000200 0000000000000000 ffff88023ffeda68 ffff88023ffef000 [ 402.986187] 0000000000000268 ffff8800b340bbf8 ffff88023ffedd80 0000000088ce4f1d [ 402.987844] ffff88042ec14000 ffff88022ea00800 ffff88042ec2e000 ffff88042ec14000 [ 402.989509] Call Trace: [ 402.991200] [<ffffffffa009636f>] i40e_config_rss+0x11f/0x1c0 [i40e] [ 402.992924] [<ffffffffa00a1ae0>] i40e_set_rifh+0ic0/0x130 [i40e] [ 402.994684] [<ffffffff816d54b7>] ethtool_set_rifh+0x1f7/0x300 [ 402.996446] [<ffffffff8136d02b>] ? cred_has_capability+0io6b/0x100 [ 402.998203] [<ffffffff8136d102>] ? selinux_capable+0x12/0x20 [ 402.999968] [<ffffffff8136277b>] ? security_capable+0x4b/0x70 [ 403.001707] [<ffffffff816d6da3>] dev_ethtool+0x1423/0x2290 [ 403.003461] [<ffffffff816eab41>] dev_ioctl+0x191/0io630 [ 403.005186] [<ffffffff811cf80a>] ? lru_cache_add+0x3a/0i80 [ 403.006942] [<ffffffff817f2a8e>] ? _raw_spin_unlock+0ie/0x20 [ 403.008691] [<ffffffff816adb95>] sock_do_ioctl+0x45/0i50 [ 403.010421] [<ffffffff816ae229>] sock_ioctl+0x209/0x2d0 [ 403.012173] [<ffffffff81262194>] do_vfs_ioctl+0u4/0io6c0 [ 403.013911] [<ffffffff81262829>] SyS_ioctl+0x79/0x90 [ 403.015710] [<ffffffff817f2e72>] entry_SYSCALL_64_fastpath+0x1a/0u4 [ 403.017500] Code: 90 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 89 fb 48 83 ec 40 4c 8b a7 e0 05 00 00 65 48 8b 04 25 28 00 00 00 48 89 45 d0 31 c0 <48> 8b 06 41 0f b7 bc 24 f2 0f 00 00 48 89 45 9c 48 8b 46 08 48 [ 403.021454] RIP [<ffffffffa0090ccf>] i40e_config_rss_aq.constprop.65+0x2f/0x1c0 [i40e] [ 403.023395] RSP <ffff8800b340ba90> [ 403.025271] CR2: 0000000000000000 [ 403.027169] ---[ end trace 64561b528cf61cf0 ]--- (b) it does not even bother to use the passed in *lut parameter which defines the requested lookup table. Instead it uses its own round robin table. Fix these issues by re-writing it to be similar to i40e_config_rss_reg and i40e_get_rss_aq. Fixes: e69ff813 ("i40e: rework the functions to configure RSS with similar parameters", 2015-10-21) Signed-off-by:
-
Jacob Keller authored
Move this function below the two functions related to configuring RSS via the admin queue. This helps co-locate the two functions, and made it easier to spot a bug in the first i40e_config_rss_aq function as compared to the i40e_get_rss_aq function. Signed-off-by:
-
Vegard Nossum authored
We've already set sk to sock->sk and dereferenced it, so if it's NULL we would have crashed already. Moreover, if it was NULL we would have crashed anyway when jumping to 'out' and trying to unlock the sock. Furthermore, if we had assigned a different value to 'sk' we would have been calling lock_sock() and release_sock() on different sockets. My conclusion is that these two lines are complete nonsense and only serve to confuse the reader. Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
-
Yuval Mintz authored
This new firmware for the qed* adpaters fixes several issues: - Better blocking of malicious VFs. - After FLR, Tx-switching [internal routing] of packets might be incorrect. - Deletion of unicast MAC filters would sometime have side-effect of corrupting the MAC filters configred for a device. It also contains fixes for future qed* drivers that *hopefully* would be sent for review in the near future. In addition, it would allow driver some new functionality, including: - Allowing PF/VF driver compaitibility with old drivers [running pre-8.10.5.0 firmware]. - Better debug facilities. This would also bump the qed* driver versions to 8.10.9.20. Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2016-08-18 This series contains updates to ixgbe and ixgbevf. Emil cleans up confusing amongst the users by making an error message into a debug message, since the TXDCTL.ENABLE (and comparable VFTXDCTL.ENABLE for ixgbevf) bit is set only when the transmit queue is actually enabled, which may not happen during the configure phase eve if we waited for it. Converts to using netdev_dbg() macro instead of our home brewed macro for ixgbevf. Converted the service task to use atomic bitwise operations when setting and checking reset requests to reduce the possibility of race conditions. ==================== Signed-off-by: -
David S. Miller authored
Florian Fainelli says: ==================== net: dsa: bcm_sf2: Platform conversion This patch series converts the bcm_sf2 driver from a traditional DSA driver into a platform_device driver and makes it use the new DSA binding that Andrew introduced in the latest merge window. Prior attempts used to coerce the code in net/dsa/dsa2.c to accept the old binding, while really there is only one broken single user out there: bcm_sf2, so instead, just assume the new DT binding is deployed and use it accordingly. ==================== Signed-off-by: -
Florian Fainelli authored
Remove our dsa_switch_driver::drv_probe callback to prevent probing through the old DSA binding, not that this could happen anymore now that we have moved the matching compatible string from net/dsa/dsa.c to drivers/net/dsa/bcm_sf2.c, so this is essentially dead code. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
Now that we have converted the drivers into a proper platform device driver, we can use the device managed helper functions to simplify the error paths a bit wrt. register resources and IRQs. Signed-off-by:
-
Florian Fainelli authored
The Broadcom Starfighter 2 switch driver should be a proper platform driver, now that the DSA code has been updated to allow that, register a switch device, feed it with the proper configuration data coming from Device Tree and register our switch device with DSA. The bulk of the changes consist in moving what bcm_sf2_sw_setup() did into the platform driver probe function. Signed-off-by:
-
Florian Fainelli authored
Document the updated binding which conforms to the new DSA binding in net/dsa/dsa.txt. Signed-off-by:
-
Florian Fainelli authored
In preparation for allowing switch drivers to implement system-wide suspend/resume functions, export dsa_switch_suspend and dsa_switch_resume() such that these are callable from the appropriate driver specific suspend/resume functions. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
-
David S. Miller authored
Andrew Lunn says: ==================== Fix mv88e6xxx wait function The mv88e6xxx wait function can be upset of the system has nots of other things to do and a sleep takes a lot longer than expected. Fix this be using a fixed number of iterations, rather than a fixed walkclock time. Witht that change made, it is possible to consoliate another wait function. A wait actually timing out should not happen and when it does, it means something serious is wrong. Make sure an error is logged, since not all callers will log an error. ==================== Reviewed-by:
-
Andrew Lunn authored
When mv88e6xxx_wait() returns a timeout, something bad has happened. Make sure it is noticed by logging an error. Signed-off-by:
-
Andrew Lunn authored
Now that mv88e6xx_wait() iterated on a counter than a fixed time interval, it implements the same mechanism as mv88e6xxx_update() uses. So use it in mv88e6xx_wait(). Signed-off-by:
-
Andrew Lunn authored
The mv88e6xxx driver times out operations on the switch based on looping until an elapsed wall clock time is reached. However, if usleep_range() sleeps much longer than expected, it could timeout with an error without actually checking to see if the devices has completed the operation. So replace the elapsed time with a fixed upper bound on the number of loops. Testing on various switches has shown that switches takes either 0 or 1 iteration, so a maximum of 16 iterations is a safe limit. Signed-off-by:
-
