- 26 Jun, 2017 40 commits
-
-
Tony Lindgren authored
[ Upstream commit 8b8a84c5 ] Commit 16fa3dc7 ("mfd: omap-usb-tll: HOST TLL platform driver") added support for USB TLL, but uses OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF bit the wrong way. The comments in the code are correct, but the inverted use of OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF causes the register to be enabled instead of disabled unlike what the comments say. Without this change the Wrigley 3G LTE modem on droid 4 EHCI bus can be only pinged few times before it stops responding. Fixes: 16fa3dc7 ("mfd: omap-usb-tll: HOST TLL platform driver") Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Sasha Levin <alexander.levin@verizon.com>
-
Laura Abbott authored
[ Upstream commit 861ce4a3 ] '__vmalloc_start_set' currently only gets set in initmem_init() when !CONFIG_NEED_MULTIPLE_NODES. This breaks detection of vmalloc address with virt_addr_valid() with CONFIG_NEED_MULTIPLE_NODES=y, causing a kernel crash: [mm/usercopy] 517e1fbe: kernel BUG at arch/x86/mm/physaddr.c:78! Set '__vmalloc_start_set' appropriately for that case as well. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Laura Abbott <labbott@redhat.com> Reviewed-by:
Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: dc16ecf7 ("x86-32: use specific __vmalloc_start_set flag in __virt_addr_valid") Link: http://lkml.kernel.org/r/1494278596-30373-1-git-send-email-labbott@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit be40597a ] UARTn_FRAME_PARITY_ODD is 0x0300 UARTn_FRAME_PARITY_EVEN is 0x0200 So if the UART is configured for EVEN parity, it would be reported as ODD. Fix it by correctly testing if the 2 bits are set. Fixes: 3afbd89c ("serial/efm32: add new driver") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Emmanuel Grumbach authored
[ Upstream commit b3dd8279 ] mac80211 allows to modify the SMPS state of an AP both, when it is started, and after it has been started. Such a change will trigger an action frame to all the peers that are currently connected, and will be remembered so that new peers will get notified as soon as they connect (since the SMPS setting in the beacon may not be the right one). This means that we need to remember the SMPS state currently requested as well as the SMPS state that was configured initially (and advertised in the beacon). The former is bss->req_smps and the latter is sdata->smps_mode. Initially, the AP interface could only be started with SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF always. Later, a nl80211 API was added to be able to start an AP with a different AP mode. That code forgot to update bss->req_smps and because of that, if the AP interface was started with SMPS_DYNAMIC, we had: sdata->smps_mode = SMPS_DYNAMIC bss->req_smps = SMPS_OFF That configuration made mac80211 think it needs to fire off an action frame to any new station connecting to the AP in order to let it know that the actual SMPS configuration is SMPS_OFF. Fix that by properly setting bss->req_smps in ieee80211_start_ap. Fixes: f6993174 ("mac80211: set smps_mode according to ap params") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
Luca Coelho <luciano.coelho@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit f1f3e9e2 ] When VHT IBSS support was added, the size of the extra elements wasn't considered in ieee80211_ibss_build_presp(), which makes it possible that it would overrun the allocated buffer. Fix it by allocating the necessary space. Fixes: abcff6ef ("mac80211: add VHT support for IBSS") Reported-by:
Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by:
-
Koen Vandeputte authored
[ Upstream commit f181d6a3 ] Add the missing IBSS capability flag during capability init as it needs to be inserted into the generated beacon in order for CSA to work. Fixes: cd7760e6 ("mac80211: add support for CSA in IBSS mode") Signed-off-by:
Piotr Gawlowicz <gawlowicz@tkn.tu-berlin.de> Signed-off-by:
Mikołaj Chwalisz <chwalisz@tkn.tu-berlin.de> Tested-by:
Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by:
-
Jason A. Donenfeld authored
[ Upstream commit 98c67d18 ] Otherwise, we enable all sorts of forgeries via timing attack. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: linux-wireless@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by:
-
Emmanuel Grumbach authored
[ Upstream commit 769dc04d ] When a peer sends a BAR frame with PM bit clear, we should not modify its PM state as madated by the spec in 802.11-20012 10.2.1.2. Cc: stable@vger.kernel.org Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 5ebb6dd3 ] We should ensure that 'plane_no' is '< vb->num_planes' as done in 'vb2_plane_cookie' just a few lines below. Fixes: e23ccc0a ("[media] v4l: add videobuf2 Video for Linux 2 driver framework") Cc: stable@vger.kernel.org Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Marc Kleine-Budde authored
[ Upstream commit 5cda3ee5 ] This patch adds the missing kfree() in gs_cmd_reset() to free the memory that is not used anymore after usb_control_msg(). Cc: linux-stable <stable@vger.kernel.org> Cc: Maximilian Schneider <max@schneidersoft.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Nicholas Bellinger authored
[ Upstream commit ba80aa90 ] This patch closes a long standing race in configfs between the creation of a new symlink in create_link(), while the symlink target's config_item is being concurrently removed via configfs_rmdir(). This can happen because the symlink target's reference is obtained by config_item_get() in create_link() before the CONFIGFS_USET_DROPPING bit set by configfs_detach_prep() during configfs_rmdir() shutdown is actually checked.. This originally manifested itself on ppc64 on v4.8.y under heavy load using ibmvscsi target ports with Novalink API: [ 7877.289863] rpadlpar_io: slot U8247.22L.212A91A-V1-C8 added [ 7879.893760] ------------[ cut here ]------------ [ 7879.893768] WARNING: CPU: 15 PID: 17585 at ./include/linux/kref.h:46 config_item_get+0x7c/0x90 [configfs] [ 7879.893811] CPU: 15 PID: 17585 Comm: targetcli Tainted: G O 4.8.17-customv2.22 #12 [ 7879.893812] task: c00000018a0d3400 task.stack: c0000001f3b40000 [ 7879.893813] NIP: d000000002c664ec LR: d000000002c60980 CTR: c000000000b70870 [ 7879.893814] REGS: c0000001f3b43810 TRAP: 0700 Tainted: G O (4.8.17-customv2.22) [ 7879.893815] MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 28222242 XER: 00000000 [ 7879.893820] CFAR: d000000002c664bc SOFTE: 1 GPR00: d000000002c60980 c0000001f3b43a90 d000000002c70908 c0000000fbc06820 GPR04: c0000001ef1bd900 0000000000000004 0000000000000001 0000000000000000 GPR08: 0000000000000000 0000000000000001 d000000002c69560 d000000002c66d80 GPR12: c000000000b70870 c00000000e798700 c0000001f3b43ca0 c0000001d4949d40 GPR16: c00000014637e1c0 0000000000000000 0000000000000000 c0000000f2392940 GPR20: c0000001f3b43b98 0000000000000041 0000000000600000 0000000000000000 GPR24: fffffffffffff000 0000000000000000 d000000002c60be0 c0000001f1dac490 GPR28: 0000000000000004 0000000000000000 c0000001ef1bd900 c0000000f2392940 [ 7879.893839] NIP [d000000002c664ec] config_item_get+0x7c/0x90 [configfs] [ 7879.893841] LR [d000000002c60980] check_perm+0x80/0x2e0 [configfs] [ 7879.893842] Call Trace: [ 7879.893844] [c0000001f3b43ac0] [d000000002c60980] check_perm+0x80/0x2e0 [configfs] [ 7879.893847] [c0000001f3b43b10] [c000000000329770] do_dentry_open+0x2c0/0x460 [ 7879.893849] [c0000001f3b43b70] [c000000000344480] path_openat+0x210/0x1490 [ 7879.893851] [c0000001f3b43c80] [c00000000034708c] do_filp_open+0xfc/0x170 [ 7879.893853] [c0000001f3b43db0] [c00000000032b5bc] do_sys_open+0x1cc/0x390 [ 7879.893856] [c0000001f3b43e30] [c000000000009584] system_call+0x38/0xec [ 7879.893856] Instruction dump: [ 7879.893858] 409d0014 38210030 e8010010 7c0803a6 4e800020 3d220000 e94981e0 892a0000 [ 7879.893861] 2f890000 409effe0 39200001 992a0000 <0fe00000> 4bffffd0 60000000 60000000 [ 7879.893866] ---[ end trace 14078f0b3b5ad0aa ]--- To close this race, go ahead and obtain the symlink's target config_item reference only after the existing CONFIGFS_USET_DROPPING check succeeds. This way, if configfs_rmdir() wins create_link() will return -ENONET, and if create_link() wins configfs_rmdir() will return -EBUSY. Reported-by:
Bryant G. Ly <bryantly@linux.vnet.ibm.com> Tested-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit b5c32061 ] My static checker complains that if "lvl" is ULONG_MAX (this is 64 bit) then some of the strings will overflow. I don't know if that's possible but it seems simple enough to make the buffers slightly larger. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Max Filippov authored
[ Upstream commit e5c86679 ] Linux IRQ #0 is reserved for error reporting and may not be used. Increase NR_IRQS for one additional slot and increase irq_domain_add_legacy parameter first_irq value to 1, so that linux IRQ #0 is not associated with hardware IRQ #0 in legacy IRQ domains. Introduce macro XTENSA_PIC_LINUX_IRQ for static translation of xtensa PIC hardware IRQ # to linux IRQ #. Use this macro in XTFPGA platform data definitions. This fixes inability to use hardware IRQ #0 in configurations that don't use device tree and allows for non-identity mapping between linux IRQ # and hardware IRQ #. Cc: stable@vger.kernel.org Signed-off-by:
Max Filippov <jcmvbkbc@gmail.com> Signed-off-by:
-
Parthasarathy Bhuvaragan authored
[ Upstream commit 4c887aa6 ] In tipc_conn_sendmsg(), we first queue the request to the outqueue followed by the connection state check. If the connection is not connected, we should not queue this message. In this commit, we reject the messages if the connection state is not CF_CONNECTED. Acked-by:
Ying Xue <ying.xue@windriver.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Tested-by:
John Thompson <thompa.atl@gmail.com> Signed-off-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 3ba4bcee ] We have seen proc_pid_readdir() invocations holding cpu for more than 50 ms. Add a cond_resched() to be gentle with other tasks. [akpm@linux-foundation.org: coding style fix] Link: http://lkml.kernel.org/r/1484238380.15816.42.camel@edumazet-glaptop3.roam.corp.google.comSigned-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Coly Li authored
[ Upstream commit f598f82e ] Commit 8a59f5d2 ("fs/romfs: return f_fsid for statfs(2)") generates a 64bit id from sb->s_bdev->bd_dev. This is only correct when romfs is defined with CONFIG_ROMFS_ON_BLOCK. If romfs is only defined with CONFIG_ROMFS_ON_MTD, sb->s_bdev is NULL, referencing sb->s_bdev->bd_dev will triger an oops. Richard Weinberger points out that when CONFIG_ROMFS_BACKED_BY_BOTH=y, both CONFIG_ROMFS_ON_BLOCK and CONFIG_ROMFS_ON_MTD are defined. Therefore when calling huge_encode_dev() to generate a 64bit id, I use the follow order to choose parameter, - CONFIG_ROMFS_ON_BLOCK defined use sb->s_bdev->bd_dev - CONFIG_ROMFS_ON_BLOCK undefined and CONFIG_ROMFS_ON_MTD defined use sb->s_dev when, - both CONFIG_ROMFS_ON_BLOCK and CONFIG_ROMFS_ON_MTD undefined leave id as 0 When CONFIG_ROMFS_ON_MTD is defined and sb->s_mtd is not NULL, sb->s_dev is set to a device ID generated by MTD_BLOCK_MAJOR and mtd index, otherwise sb->s_dev is 0. This is a try-best effort to generate a uniq file system ID, if all the above conditions are not meet, f_fsid of this romfs instance will be 0. Generally only one romfs can be built on single MTD block device, this method is enough to identify multiple romfs instances in a computer. Link: http://lkml.kernel.org/r/1482928596-115155-1-git-send-email-colyli@suse.deSigned-off-by:
Coly Li <colyli@suse.de> Reported-by:
Nong Li <nongli1031@gmail.com> Tested-by:
-
Randy Dunlap authored
[ Upstream commit 3705ccfd ] When CONFIG_FPU is not enabled on arch/mn10300, <asm/switch_to.h> causes a build error with a call to fpu_save(): kernel/built-in.o: In function `.L410': core.c:(.sched.text+0x28a): undefined reference to `fpu_save' Fix this by including <asm/fpu.h> in <asm/switch_to.h> so that an empty static inline fpu_save() is defined. Link: http://lkml.kernel.org/r/dc421c4f-4842-4429-1b99-92865c2f24b6@infradead.orgSigned-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 6f29a130 ] sctp_addr_id2transport is a function for sockopt to look up assoc by address. As the address is from userspace, it can be a v4-mapped v6 address. But in sctp protocol stack, it always handles a v4-mapped v6 address as a v4 address. So it's necessary to convert it to a v4 address before looking up assoc by address. This patch is to fix it by calling sctp_verify_addr in which it can do this conversion before calling sctp_endpoint_lookup_assoc, just like what sctp_sendmsg and __sctp_connect do for the address from users. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
hayeswang authored
[ Upstream commit 248b213a ] Re-schedule napi after napi_complete() for tx, if it is necessay. In r8152_poll(), if the tx is completed after tx_bottom() and before napi_complete(), the scheduling of napi would be lost. Then, no one handles the next tx until the next napi_schedule() is called. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Y.C. Chen authored
[ Upstream commit 6c971c09 ] The original ast driver will access some BMC configuration through P2A bridge that can be disabled since AST2300 and after. It will cause system hanged if P2A bridge is disabled. Here is the update to fix it. Signed-off-by:
Y.C. Chen <yc_chen@aspeedtech.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Lyude Paul authored
[ Upstream commit cae9ff03 ] As it turns out, on cards that actually have CRTCs on them we're already calling drm_kms_helper_poll_enable(drm_dev) from nouveau_display_resume() before we call it in nouveau_pmops_runtime_resume(). This leads us to accidentally trying to enable polling twice, which results in a potential deadlock between the RPM locks and drm_dev->mode_config.mutex if we end up trying to enable polling the second time while output_poll_execute is running and holding the mode_config lock. As such, make sure we only enable polling in nouveau_pmops_runtime_resume() if we need to. This fixes hangs observed on the ThinkPad W541 Signed-off-by:
Lyude <lyude@redhat.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Kilian Singer <kilian.singer@quantumtechnology.info> Cc: Lukas Wunner <lukas@wunner.de> Cc: David Airlie <airlied@redhat.com> Signed-off-by:
-
Helge Deller authored
[ Upstream commit 83b5d1e3 ] Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit d1156b48 ] init_ring(), refill_rx_ring() and start_tx() don't check if mapping dma memory succeed. The patch adds the checks and failure handling. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Jack Morgenstein authored
[ Upstream commit d585df1c ] Some Hypervisors detach VFs from VMs by instantly causing an FLR event to be generated for a VF. In the mlx4 case, this will cause that VF's comm channel to be disabled before the VM has an opportunity to invoke the VF device's "shutdown" method. The result is that the VF driver on the VM will experience a command timeout during the shutdown process when the Hypervisor does not deliver a command-completion event to the VM. To avoid FW command timeouts on the VM when the driver's shutdown method is invoked, we detect the absence of the VF's comm channel at the very start of the shutdown process. If the comm-channel has already been disabled, we cause all FW commands during the device shutdown process to immediately return success (and thus avoid all command timeouts). Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Signed-off-by:
-
Ben Skeggs authored
[ Upstream commit 96692b09 ] Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
David Howells authored
[ Upstream commit 6bdded59 ] fscache_disable_cookie() needs to clear the outstanding writes on the cookie it's disabling because they cannot be completed after. Without this, fscache_nfs_open_file() gets stuck because it disables the cookie when the file is opened for writing but can't uncache the pages till afterwards - otherwise there's a race between the open routine and anyone who already has it open R/O and is still reading from it. Looking in /proc/pid/stack of the offending process shows: [<ffffffffa0142883>] __fscache_wait_on_page_write+0x82/0x9b [fscache] [<ffffffffa014336e>] __fscache_uncache_all_inode_pages+0x91/0xe1 [fscache] [<ffffffffa01740fa>] nfs_fscache_open_file+0x59/0x9e [nfs] [<ffffffffa01ccf41>] nfs4_file_open+0x17f/0x1b8 [nfsv4] [<ffffffff8117350e>] do_dentry_open+0x16d/0x2b7 [<ffffffff811743ac>] vfs_open+0x5c/0x65 [<ffffffff81184185>] path_openat+0x785/0x8fb [<ffffffff81184343>] do_filp_open+0x48/0x9e [<ffffffff81174710>] do_sys_open+0x13b/0x1cb [<ffffffff811747b9>] SyS_open+0x19/0x1b [<ffffffff81001c44>] do_syscall_64+0x80/0x17a [<ffffffff8165c2da>] return_from_SYSCALL_64+0x0/0x7a [<ffffffffffffffff>] 0xffffffffffffffff Reported-by:
Jianhong Yin <jiyin@redhat.com> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Acked-by:
Steve Dickson <steved@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Stanislaw Gruszka authored
[ Upstream commit 3808d348 ] If ->get_regs_len() callback return 0, we allocate 0 bytes of memory, what print ugly warning in dmesg, which can be found further below. This happen on mac80211 devices where ieee80211_get_regs_len() just return 0 and driver only fills ethtool_regs structure and actually do not provide any dump. However I assume this can happen on other drivers i.e. when for some devices driver provide regs dump and for others do not. Hence preventing to to print warning in ethtool code seems to be reasonable. ethtool: vmalloc: allocation failure: 0 bytes, mode:0x24080c2(GFP_KERNEL|__GFP_HIGHMEM|__GFP_ZERO) <snip> Call Trace: [<ffffffff813bde47>] dump_stack+0x63/0x8c [<ffffffff811b0a1f>] warn_alloc+0x13f/0x170 [<ffffffff811f0476>] __vmalloc_node_range+0x1e6/0x2c0 [<ffffffff811f0874>] vzalloc+0x54/0x60 [<ffffffff8169986c>] dev_ethtool+0xb4c/0x1b30 [<ffffffff816adbb1>] dev_ioctl+0x181/0x520 [<ffffffff816714d2>] sock_do_ioctl+0x42/0x50 <snip> Mem-Info: active_anon:435809 inactive_anon:173951 isolated_anon:0 active_file:835822 inactive_file:196932 isolated_file:0 unevictable:0 dirty:8 writeback:0 unstable:0 slab_reclaimable:157732 slab_unreclaimable:10022 mapped:83042 shmem:306356 pagetables:9507 bounce:0 free:130041 free_pcp:1080 free_cma:0 Node 0 active_anon:1743236kB inactive_anon:695804kB active_file:3343288kB inactive_file:787728kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:332168kB dirty:32kB writeback:0kB shmem:0kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 1225424kB writeback_tmp:0kB unstable:0kB pages_scanned:0 all_unreclaimable? no Node 0 DMA free:15900kB min:136kB low:168kB high:200kB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15984kB managed:15900kB mlocked:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:0kB pagetables:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB lowmem_reserve[]: 0 3187 7643 7643 Node 0 DMA32 free:419732kB min:28124kB low:35152kB high:42180kB active_anon:541180kB inactive_anon:248988kB active_file:1466388kB inactive_file:389632kB unevictable:0kB writepending:0kB present:3370280kB managed:3290932kB mlocked:0kB slab_reclaimable:217184kB slab_unreclaimable:4180kB kernel_stack:160kB pagetables:984kB bounce:0kB free_pcp:2236kB local_pcp:660kB free_cma:0kB lowmem_reserve[]: 0 0 4456 4456 Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Ard Biesheuvel authored
[ Upstream commit 29905b52 ] The function order_base_2() is defined (according to the comment block) as returning zero on input zero, but subsequently passes the input into roundup_pow_of_two(), which is explicitly undefined for input zero. This has gone unnoticed until now, but optimization passes in GCC 7 may produce constant folded function instances where a constant value of zero is passed into order_base_2(), resulting in link errors against the deliberately undefined '____ilog2_NaN'. So update order_base_2() to adhere to its own documented interface. [ See http://marc.info/?l=linux-kernel&m=147672952517795&w=2 and follow-up discussion for more background. The gcc "optimization pass" is really just broken, but now the GCC trunk problem seems to have escaped out of just specially built daily images, so we need to work around it in mainline. - Linus ] Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 4f40c6e5 ] After much waiting I finally reproduced a KASAN issue, only to find my trace-buffer empty of useful information because it got spooled out :/ Make kasan_report honour the /proc/sys/kernel/traceoff_on_warning interface. Link: http://lkml.kernel.org/r/20170125164106.3514-1-aryabinin@virtuozzo.comSigned-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by:
Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
David Lin authored
[ Upstream commit 35f860f9 ] Some versions of ARM GCC compiler such as Android toolchain throws in a '-fpic' flag by default. This causes the gcc-goto check script to fail although some config would have '-fno-pic' flag in the KBUILD_CFLAGS. This patch passes the KBUILD_CFLAGS to the check script so that the script does not rely on the default config from different compilers. Link: http://lkml.kernel.org/r/20170120234329.78868-1-dtwlin@google.comSigned-off-by:
David Lin <dtwlin@google.com> Acked-by:
Steven Rostedt <rostedt@goodmis.org> Cc: Michal Marek <mmarek@suse.com> Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit a9306a63 ] The might_sleep_if() assertions in __pm_runtime_idle(), __pm_runtime_suspend() and __pm_runtime_resume() may generate false-positive warnings in some situations. For example, that happens if a nested pm_runtime_get_sync()/pm_runtime_put() pair is executed with disabled interrupts within an outer pm_runtime_get_sync()/pm_runtime_put() section for the same device. [Generally, pm_runtime_get_sync() may sleep, so it should not be called with disabled interrupts, but in this particular case the previous pm_runtime_get_sync() guarantees that the device will not be suspended, so the inner pm_runtime_get_sync() will return immediately after incrementing the device's usage counter.] That started to happen in the i915 driver in 4.10-rc, leading to the following splat: BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1032 in_atomic(): 1, irqs_disabled(): 0, pid: 1500, name: Xorg 1 lock held by Xorg/1500: #0: (&dev->struct_mutex){+.+.+.}, at: [<ffffffffa0680c13>] i915_mutex_lock_interruptible+0x43/0x140 [i915] CPU: 0 PID: 1500 Comm: Xorg Not tainted Call Trace: dump_stack+0x85/0xc2 ___might_sleep+0x196/0x260 __might_sleep+0x53/0xb0 __pm_runtime_resume+0x7a/0x90 intel_runtime_pm_get+0x25/0x90 [i915] aliasing_gtt_bind_vma+0xaa/0xf0 [i915] i915_vma_bind+0xaf/0x1e0 [i915] i915_gem_execbuffer_relocate_entry+0x513/0x6f0 [i915] i915_gem_execbuffer_relocate_vma.isra.34+0x188/0x250 [i915] ? trace_hardirqs_on+0xd/0x10 ? i915_gem_execbuffer_reserve_vma.isra.31+0x152/0x1f0 [i915] ? i915_gem_execbuffer_reserve.isra.32+0x372/0x3a0 [i915] i915_gem_do_execbuffer.isra.38+0xa70/0x1a40 [i915] ? __might_fault+0x4e/0xb0 i915_gem_execbuffer2+0xc5/0x260 [i915] ? __might_fault+0x4e/0xb0 drm_ioctl+0x206/0x450 [drm] ? i915_gem_execbuffer+0x340/0x340 [i915] ? __fget+0x5/0x200 do_vfs_ioctl+0x91/0x6f0 ? __fget+0x111/0x200 ? __fget+0x5/0x200 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x23/0xc6 even though the code triggering it is correct. Unfortunately, the might_sleep_if() assertions in question are too coarse-grained to cover such cases correctly, so make them a bit less sensitive in order to avoid the false-positives. Reported-and-tested-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 5aff1d24 ] The symbols can no longer be used as loadable modules, leading to a harmless Kconfig warning: arch/arm/configs/imote2_defconfig:60:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE arch/arm/configs/imote2_defconfig:59:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP arch/arm/configs/ezx_defconfig:68:warning: symbol value 'm' invalid for NF_CT_PROTO_UDPLITE arch/arm/configs/ezx_defconfig:67:warning: symbol value 'm' invalid for NF_CT_PROTO_SCTP Let's make them built-in. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Linus Lüssing authored
[ Upstream commit a088d1d7 ] When for instance a mobile Linux device roams from one access point to another with both APs sharing the same broadcast domain and a multicast snooping switch in between: 1) (c) <~~~> (AP1) <--[SSW]--> (AP2) 2) (AP1) <--[SSW]--> (AP2) <~~~> (c) Then currently IPv6 multicast packets will get lost for (c) until an MLD Querier sends its next query message. The packet loss occurs because upon roaming the Linux host so far stayed silent regarding MLD and the snooping switch will therefore be unaware of the multicast topology change for a while. This patch fixes this by always resending MLD reports when an interface change happens, for instance from NO-CARRIER to CARRIER state. Signed-off-by:
Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by:
-
Stefan Brüns authored
[ Upstream commit 5a70348e ] If a context is configured as dualstack ("IPv4v6"), the modem indicates the context activation with a slightly different indication message. The dual-stack indication omits the link_type (IPv4/v6) and adds additional address fields. IPv6 LSIs are identical to IPv4 LSIs, but have a different link type. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Reviewed-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Stefan Brüns authored
[ Upstream commit 764895d3 ] When the context is deactivated, the link_type is set to 0xff, which triggers a warning message, and results in a wrong link status, as the LSI is ignored. Signed-off-by:
-
Ralf Baechle authored
[ Upstream commit 7ba1b689 ] If a USB-to-serial adapter is unplugged, the driver re-initializes, with dev->hard_header_len and dev->addr_len set to zero, instead of the correct values. If then a packet is sent through the half-dead interface, the kernel will panic due to running out of headroom in the skb when pushing for the AX.25 headers resulting in this panic: [<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50) [<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25]) [<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss]) [<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8) [<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914) [<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0) [<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48) This patch makes mkiss behave like the 6pack driver. 6pack does not panic. In 6pack.c sp_setup() (same function name here) the values for dev->hard_header_len and dev->addr_len are set to the same values as in my mkiss patch. [ralf@linux-mips.org: Massages original submission to conform to the usual standards for patch submissions.] Signed-off-by:
Thomas Osterried <thomas@osterried.de> Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Ralf Baechle authored
[ Upstream commit 4872e57c ] When sending ARP requests over AX.25 links the hwaddress in the neighbour cache are not getting initialized. For such an incomplete arp entry ax2asc2 will generate an empty string resulting in /proc/net/arp output like the following: $ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3 172.20.1.99 0x3 0x0 * bpq0 The missing field will confuse the procfs parsing of arp(8) resulting in incorrect output for the device such as the following: $ arp Address HWtype HWaddress Flags Mask Iface gateway ether 52:54:00:00:5d:5f C ens3 172.20.1.99 (incomplete) ens3 This changes the content of /proc/net/arp to: $ cat /proc/net/arp IP address HW type Flags HW address Mask Device 172.20.1.99 0x3 0x0 * * bpq0 192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3 To do so it change ax2asc to put the string "*" in buf for a NULL address argument. Finally the HW address field is left aligned in a 17 character field (the length of an ethernet HW address in the usual hex notation) for readability. Signed-off-by:
-
Jonathan T. Leighton authored
[ Upstream commit ec5e3b0a ] This patch adds a check for the problematic case of an IPv4-mapped IPv6 source address and a destination address that is neither an IPv4-mapped IPv6 address nor in6addr_any, and returns an appropriate error. The check in done before returning from looking up the route. Signed-off-by:
Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by:
-
Jonathan T. Leighton authored
[ Upstream commit 052d2369 ] This patch adds a check on the type of the source address for the case where the destination address is in6addr_any. If the source is an IPv4-mapped IPv6 source address, the destination is changed to ::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This is done in three locations to handle UDP calls to either connect() or sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays handling an in6addr_any destination until very late, so the patch only needs to handle the case where the source is an IPv4-mapped IPv6 address. Signed-off-by:
-
Anssi Hannula authored
[ Upstream commit cd224553 ] xilinx_emaclite looks at the received data to try to determine the Ethernet packet length but does not properly clamp it if proto_type == ETH_P_IP or 1500 < proto_type <= 1518, causing a buffer overflow and a panic via skb_panic() as the length exceeds the allocated skb size. Fix those cases. Also add an additional unconditional check with WARN_ON() at the end. Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: bb81b2dd ("net: add Xilinx emac lite device driver") Signed-off-by:
-
