- 26 Jul, 2010 40 commits
-
-
Eric Bénard authored
as per suggested by Sascha Signed-off-by:
Eric Bénard <eric@eukrea.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de>
-
Eric Bénard authored
This patch fixes the following Kconfig warning : "arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its choice group Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Marc Kleine-Budde authored
Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Marc Kleine-Budde authored
In order to make this patch compile, even if the flexcan driver with it's header defining the platform data isn't merged yet, two ifdefs have been added. They effect that the "imx_add_flexcan" function results in a no-op function if the driver hasn't been activated. These ifdefs can be removed after the flexcan driver has been merged. Signed-off-by:
-
Marc Kleine-Budde authored
Signed-off-by:
-
Marc Kleine-Budde authored
Signed-off-by:
-
Marc Kleine-Budde authored
Signed-off-by:
-
Sascha Hauer authored
Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15 and one for gpio 16 to 31. Actually only the lower IRQ is registered so register the second one. Signed-off-by:
-
Eric Bénard authored
the i2c_board_info structure landed into the SPI #if/#endif which is wrong. Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Eric Bénard authored
DEBUG_LL is actually broken on i.MX25, this patch fix it. Signed-off-by:
-
Eric Bénard authored
Signed-off-by:
-
Jason Wang authored
Add keymaps and imx_keypad device registration for imx51_3ds board. Signed-off-by:
Jason Wang <jason77.wang@gmail.com> Signed-off-by:
-
Jason Wang authored
add imx_keypad platform device definition and clocks for mx51 platforms. Signed-off-by:
-
Jason Wang authored
3-stack is a reference board from Freescale for their i.MX51 SoC. Add board definition, Kconfig and Makefile to enable Freescale 3-stack board. Boot tested on a i.MX51 3-stack Rev2.0 board Signed-off-by:
-
Rogerio Pimentel authored
mx27_3ds: add support for the keypad Signed-off-by:
Rogerio Pimentel <rogerio.pimentel@freescale.com> Signed-off-by:
-
Jason Wang authored
Because we add a 3ds debug board support in mxc level, we remove those redundant codes from board level. Signed-off-by:
-
Jason Wang authored
The debug board is little different for all mxc 3-stack(PDK) platforms, it is possible here to add a common implementation to support this board. Signed-off-by:
-
git://git.pengutronix.de/git/ukl/linux-2.6Uwe Kleine-König authored
There are some more conflicts than detected by git, namely support for the newly added cpuimx machines needed to be converted to dynamic device registration. Signed-off-by: -
Baruch Siach authored
Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Luotao Fu authored
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding pin multiplexing either into the initial pin config table or ifdef blocks. Signed-off-by:
Luotao Fu <l.fu@pengutronix.de> Signed-off-by:
-
Luotao Fu authored
this one adds the frambuffer device and a TFT panel to the PhyCard-S (pca100) board. Signed-off-by:
-
Jason Wang authored
These GPIO bank offsets are useful when define a gpio number. E.G. when GPIO PORTC pin 6 is used for irq request pin of external expanding device, we can define it like: #define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6) Signed-off-by:
-
Jason Wang authored
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board, add GPIO_1_6 definiton because this pin is used as a CPLD parent irq request pin on imx51_3ds board. Signed-off-by:
-
Jason Wang authored
For pad EIM_D27 to work in UART3_RTS mode, the input path should be 3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux value should be 2 instead of 8. Signed-off-by:
-
Amit Kucheria authored
The pads capable of being used as GPIOs had their pad-name and mode-name switched. Also, fix the following: - Whitespace fixes - Replace IOMUX_CONFIG_ALTn with 'n' Signed-off-by:
Amit Kucheria <amit.kucheria@canonical.com> Signed-off-by:
-
Eric Bénard authored
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host, USB OTG and I2C touchscreen controller * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
-
Baruch Siach authored
The information in the i.MX25 Reference Manual is lacking. Add information from the Freescale BSP. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Baruch Siach authored
Signed-off-by:
-
Eric Bénard authored
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host and USB OTG * mbimxsd provides access to LCD, Audio, LED, Switch button, UART ... Signed-off-by:
-
Eric Bénard authored
* add clocks for audmux and ssi 1 & 2 * add irq for ssi 1 & 2 * add devices platform for ssi1 & 2 * update audmux-v2 for i.MX25 * add base addresses for audmux & ssi 1 & 2 * add iomux configuration for GPIO for AUD5 port Signed-off-by:
-
Eric Bénard authored
i.MX25's udc port is the same as i.MX35's one Signed-off-by:
-
