- 18 Nov, 2010 39 commits
-
-
Thomas Hellstrom authored
A process suspended waiting for a higher sequence or no sequence to unreserve, a bo may be beaten to the reservation by a process with a lower sequence. In that case the first process should give up trying to reserve and return -EAGAIN. In order for that to happen, we must wake waiting processes when we change sequence, so that they have a chance to detect the new sequence. Signed-off-by:
Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by:
Dave Airlie <airlied@redhat.com>
-
Dave Airlie authored
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next: (25 commits) nouveau: Acknowledge HPD irq in handler, not bottom half drm/nouveau: Fix a few confusions between "chipset" and "card_type". drm/nouveau: don't expose backlight control when available through ACPI drm/nouveau/pm: improve memtiming mappings drm/nouveau: Make PCIE GART size depend on the available RAMIN space. drm/nouveau: Return error from nouveau_gpuobj_new if we're out of RAMIN. drm/nouveau: Fix compilation issues in nouveau_pm when CONFIG_HWMON is not set drm/nouveau: Don't use load detection for connector polling. drm/nv10-nv20: Fix instability after MPLL changes. drm/nv50: implement possible workaround for NV86 PGRAPH TLB flush hang drm/nouveau: Don't poll LVDS outputs. drm/nouveau: Use "force" to decide if analog load detection is ok or not. drm/nv04: Fix scanout over the 16MB mark. drm/nouveau: fix nv40 pcie gart size drm/nva3: fix overflow in fixed point math used for pll calculation drm/nv10: Balance RTs expected to be accessed simultaneously by the 3d engine. drm/nouveau: Expose some BO usage flags to userspace. drm/nouveau: Reduce severity of the unknown getparam error. drm/nouveau: Avoid lock dependency between ramht and ramin spinlocks. drm/nouveau: Some random cleanups. ...
-
Alex Deucher authored
We aren't currently using tiling in userspace on evergreen, but the info we currently return for the tiling info query (gb_addr_config) is no adequate for userspace tiling alignment calculations. It does not contain the bank info. Create a custom tiling info dword with all the necessary info (num channels, num banks, group size, row size). Signed-off-by:
Alex Deucher <alexdeucher@gmail.com> Signed-off-by:
-
Alex Deucher authored
We were previously dropping alignment requests on the floor when allocating buffers so we always ended up page aligned. Certain tiling modes on 6xx+ require larger alignment which wasn't happening before. Signed-off-by:
-
Thomas Hellstrom authored
Signed-off-by:
-
Alex Deucher authored
This causes the connector to not be added since i2c init fails for the adapter. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=31688 Noticed by Ari Savolainen. Signed-off-by:
-
Alex Deucher authored
These are external encoder chips connected via DVO or DP. The actual external encoder programming is handled by the kms encoder functions for primary encoder. Signed-off-by:
-
Alex Deucher authored
Handle all the various asic family specific things for DVO. Signed-off-by:
-
Alex Deucher authored
The eDP panel must be powered up for aux transactions, so power it up for detect and mode probe functions, otherwise power it up or down based on dpms. v2: - only mess with eDP panel on DCE4+ - only mess with eDP panel on eDP connectors, not all DP connectors v3: - be extra careful to only mess with eDP panels on eDP connectors v4: - avoid possible null derefernce if a connector has not been assigned to the encoder Signed-off-by:
-
Alex Deucher authored
If there was no connector mapped to the encoder, atombios_get_encoder_mode() returned 0 which is the id for DP. Return something sane instead based on the encoder id. This avoids hitting the DP paths on non-DP encoders. Signed-off-by:
-
Alex Deucher authored
Seems some newer systems require this explicitly. Signed-off-by:
-
Alex Deucher authored
Looks like a typo in: drm/radeon/r600: fix tiling issues in CS checker. (f30df2fa) Signed-off-by:
-
Vasiliy Kulikov authored
enable_vblank implementations should use negative result to indicate error. radeon_enable_vblank() returns EINVAL in this case. Change this to -EINVAL. Signed-off-by:
Vasiliy Kulikov <segoon@openwall.com> Signed-off-by:
-
Alex Deucher authored
Tiled buffers have the same alignment requirements regardless of whether the surface is for db, cb, or textures. Previously, the calculations where inconsistent for each buffer type. - Unify the alignment calculations in a common function - Standardize the alignment units (pixels for pitch/height/depth, bytes for base) - properly check the buffer base alignments Signed-off-by:
-
Andy Lutomirski authored
The old code generated an interrupt storm bad enough to completely take down my system. Signed-off-by:
Andy Lutomirski <luto@mit.edu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com>
-
Francisco Jerez authored
Signed-off-by:
Francisco Jerez <currojerez@riseup.net> Signed-off-by:
-
Ben Skeggs authored
Avoid confusing userspace by not publishing backlight controls if ACPI equivalents are available. Reported-by:
Aaron Sowry <aaron@aeneby.se> Signed-off-by:
-
Roy Spliet authored
Improvements: - Fix bug in switch statement - Add parts of 0x10022c, 0x10023c - Clean up 0x100234 - Comment out assumption in 0x100228 until verified Signed-off-by:
Roy Spliet <r.spliet@student.tudelft.nl> Signed-off-by:
-
Francisco Jerez authored
Reported-by:
Tomas Miljenovic <tomasmiljenovic@gmail.com> Signed-off-by:
-
Francisco Jerez authored
Reported-by:
-
Martin Peres authored
Signed-off-by:
Martin Peres <martin.peres@ensi-bourges.fr> Signed-off-by:
-
Francisco Jerez authored
Analog output polling makes GL programs jerky when pageflip is being used because it's carried out with the mode_config mutex held. Signed-off-by:
-
Francisco Jerez authored
Signed-off-by:
-
Ben Skeggs authored
Signed-off-by: -
Francisco Jerez authored
Reported-by:
Xavier Chantry <chantry.xavier@gmail.com> Signed-off-by:
-
Francisco Jerez authored
Signed-off-by:
-
Francisco Jerez authored
Signed-off-by:
-
Lucas Stach authored
Nouveau sets the PCIE GART size to 64MiB for all cards before nv50, but nv40 has enough RAMIN space to support 512MiB GART size. This patch fixes this value to make use of this hardware capability. Signed-off-by:
Lucas Stach <dev@lynxeye.de> Signed-off-by:
-
Ben Skeggs authored
And a slight tweak which gets us closer to VBIOS-calculated numbers. Signed-off-by: -
Francisco Jerez authored
Signed-off-by:
-
Francisco Jerez authored
This will be needed for Z compression and to take smarter placement decisions. Signed-off-by:
-
Francisco Jerez authored
Signed-off-by:
-
Francisco Jerez authored
The ramht code called some gpuobj functions with the HARDIRQ-safe RAMHT spinlock held, this could potentially lead to a dead lock because ramin_lock is HARDIRQ-unsafe. Signed-off-by:
-
Francisco Jerez authored
Remove some unused/duplicated definitions and make sparse happy again. Signed-off-by:
-
Francisco Jerez authored
Signed-off-by:
-
Francisco Jerez authored
This allows the user to set a mode larger than the native one, useful if we had trouble finding the actual native mode (e.g. because it goes above the hardware bandwidth limits). Reported-by:
Grzesiek Sójka <pld@pfu.pl> Signed-off-by:
-
Francisco Jerez authored
Reported-by:
-
Francisco Jerez authored
Signed-off-by:
-
Jiri Slaby authored
There are two messages in the ISR of nouveau which might be printed out hundred times in a second. Ratelimit them. (We need to move nouveau_ratelimit to the top of the file.) Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Reviewed-by:
Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by:
-
- 13 Nov, 2010 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6Linus Torvalds authored
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: drivers/pcmcia/soc_common.c: Use printf extension %pV pcmcia: fix warning in synclink driver pcmcia/sa1100: don't put machine specific init functions in .init.text pcmcia/cm4000: fix error code pd6729: Coding Style fixes
-
