This patch adds a generic target for SPEAr600 board that can be
configured via the device-tree. Currently the following devices
are supported via the devicetree:

- VIC interrupts
- PL011 UART
- PL061 GPIO
- Synopsys DW I2C
- Synopsys DW ethernet

Other peripheral devices (e.g. SMI flash, FSMC NAND flash etc) will
follow in later patches.

Only the spear600-evb is currently supported. Other SPEAr600
based boards will follow later.

Since the current mainline SPEAr600 code only supports the SPEAr600
evaluation board, with nearly zero peripheral devices (only UART
and GPIO), it makes sense to switch over to DT based configuration
completely now. So this patch also removes all non-DT stuff, mainly
platform device data. The files spear600.c and spear600_evb.c are
removed completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Current code has put_ioctx() called asynchronously from aio_fput_routine();
that's done *after* we have killed the request that used to pin ioctx,
so there's nothing to stop io_destroy() waiting in wait_for_all_aios()
from progressing.  As the result, we can end up with async call of
put_ioctx() being the last one and possibly happening during exit_mmap()
or elf_core_dump(), neither of which expects stray munmap() being done
to them...

We do need to prevent _freeing_ ioctx until aio_fput_routine() is done
with that, but that's all we care about - neither io_destroy() nor
exit_aio() will progress past wait_for_all_aios() until aio_fput_routine()
does really_put_req(), so the ioctx teardown won't be done until then
and we don't care about the contents of ioctx past that point.

Since actual freeing of these suckers is RCU-delayed, we don't need to
bump ioctx refcount when request goes into list for async removal.
All we need is rcu_read_lock held just over the ->ctx_lock-protected
area in aio_fput_routine().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Have ioctx_alloc() return an extra reference, so that caller would drop it
on success and not bother with re-grabbing it on failure exit.  The current
code is obviously broken - io_destroy() from another thread that managed
to guess the address io_setup() would've returned would free ioctx right
under us; gets especially interesting if aio_context_t * we pass to
io_setup() points to PROT_READ mapping, so put_user() fails and we end
up doing io_destroy() on kioctx another thread has just got freed...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs updates from Chris Mason:
 "I have two additional and btrfs fixes in my for-linus branch.  One is
  a casting error that leads to memory corruption on i386 during scrub,
  and the other fixes a corner case in the backref walking code (also
  triggered by scrub)."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix casting error in scrub reada code
  btrfs: fix locking issues in find_parent_nodes()

Respectfully revert commit e6ca7b89 "memcg: fix mapcount check
in move charge code for anonymous page" for the 3.3 release, so that
it behaves exactly like releases 2.6.35 through 3.2 in this respect.

Horiguchi-san's commit is correct in itself, 1 makes much more sense
than 2 in that check; but it does not go far enough - swapcount
should be considered too - if we really want such a check at all.

We appear to have reached agreement now, and expect that 3.4 will
remove the mapcount check, but had better not make 3.3 different.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit f0fbf0ab ("x86: integrate delay functions") converted
delay_tsc() into a random delay generator for 64 bit.  The reason is
that it merged the mostly identical versions of delay_32.c and
delay_64.c.  Though the subtle difference of the result was:

 static void delay_tsc(unsigned long loops)
 {
-	unsigned bclock, now;
+	unsigned long bclock, now;

Now the function uses rdtscl() which returns the lower 32bit of the
TSC. On 32bit that's not problematic as unsigned long is 32bit. On 64
bit this fails when the lower 32bit are close to wrap around when
bclock is read, because the following check

       if ((now - bclock) >= loops)
       	  	break;

evaluated to true on 64bit for e.g. bclock = 0xffffffff and now = 0
because the unsigned long (now - bclock) of these values results in
0xffffffff00000001 which is definitely larger than the loops
value. That explains Tvortkos observation:

"Because I am seeing udelay(500) (_occasionally_) being short, and
 that by delaying for some duration between 0us (yep) and 491us."

Make those variables explicitely u32 again, so this works for both 32
and 64 bit.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@onelan.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org # >= 2.6.27
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sound fixes from Takashi Iwai:
 "Nothing exciting here: just a few regression fixes for HD-audio and
  ASoC, also the support of missing 32bit compat ioctl for HDSPM."

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hdspm - Provide ioctl_compat
  ALSA: hda/realtek - Apply the coef-setup only to ALC269VB
  ALSA: hda - add quirk to detect CD input on Gigabyte EP45-DS3
  ASoC: neo1973: fix neo1973 wm8753 initialization

The msm git tree moved to

  git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.gitSigned-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull C6X fix from Mark Salter:
 "Fix for C6X KSTK_EIP and KSTK_ESP macros."

* tag 'for-linus' of git://linux-c6x.org/git/projects/linux-c6x-upstreaming:
  C6X: fix KSTK_EIP and KSTK_ESP macros

Pull two IOMMU fixes from Joerg Roedel:
 "The first is an additional fix for the OMAP initialization order issue
  and the second patch fixes a possible section mismatch which can lead
  to a kernel crash in the AMD IOMMU driver when suspend/resume is used
  and the compiler has not inlined the iommu_set_device_table function."

* tag 'iommu-fixes-v3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  x86/amd: iommu_set_device_table() must not be __init
  ARM: OMAP: fix iommu, not mailbox

Pull radeon drm stuff from Dave Airlie:
 "Just some radeon fixes, one is for an oops where we run out of ioremap
  space on some big hardware systems in 32-bit mode, stuff doesn't work
  properly but at least the machine will boot.

  One regression fix, and two bugs, one hw, one blit code."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix hdmi duallink checks
  drm/radeon/kms: set SX_MISC in the r6xx blit code (v2)
  drm/radeon: deal with errors from framebuffer init path.
  drm/radeon: fix a semaphore deadlock on pre cayman asics

Pull networking from David Miller:

1) IPV4 routing metrics can become stale when routes are changed by the
   administrator, fix from Steffen Klassert.

2) atl1c does "val |= XXX;" where XXX is a bit number not a bit mask,
   fix by using set_bit.  From Dan Carpenter.

3) Memory accounting bug in carl9170 driver results in wedged TX queue.
   Fix from Nicolas Cavallari.

4) iwlwifi accidently uses "sizeof(ptr)" instead of "sizeof(*ptr)", fix
   from Johannes Berg.

5) Openvswitch doesn't honor dp_ifindex when doing vport lookups, fix
   from Ben Pfaff.

6) ehea conversion to 64-bit stats lost multicast and rx_errors
   accounting, fix from Eric Dumazet.

7) Bridge state transition logging in br_stp_disable_port() is busted,
   it's emitted at the wrong time and the message is in the wrong tense,
   fix from Paulius Zaleckas.

8) mlx4 device erroneously invokes the queue resize firmware operation
   twice, fix from Jack Morgenstein.

9) Fix deadlock in usbnet, need to drop lock when invoking usb_unlink_urb()
   otherwise we recurse into taking it again.  Fix from Sebastian Siewior.

10) hyperv network driver uses the wrong driver name string, fix from
    Haiyang Zhang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/hyperv: Use the built-in macro KBUILD_MODNAME for this driver
  net/usbnet: avoid recursive locking in usbnet_stop()
  route: Remove redirect_genid
  inetpeer: Invalidate the inetpeer tree along with the routing cache
  mlx4_core: fix bug in modify_cq wrapper for resize flow.
  atl1c: set ATL1C_WORK_EVENT_RESET bit correctly
  bridge: fix state reporting when port is disabled
  bridge: br_log_state() s/entering/entered/
  ehea: restore multicast and rx_errors fields
  openvswitch: Fix checksum update for actions on UDP packets.
  openvswitch: Honor dp_ifindex, when specified, for vport lookup by name.
  iwlwifi: fix wowlan suspend
  mwifiex: reset encryption mode flag before association
  carl9170: fix frame delivery if sta is in powersave mode
  carl9170: Fix memory accounting when sta is in power-save mode.

Pull last minute fixes from Olof Johansson:
 "One samsung build fix due to a mis-applied patch, and a small set of
  OMAP fixes.  This should be the last from arm-soc for 3.3, hopefully."

* tag 'fixes-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: S3C2440: Fixed build error for s3c244x
  ARM: OMAP2+: Fix module build errors with CONFIG_OMAP4_ERRATA_I688
  ARM: OMAP: id: Add missing break statement in omap3xxx_check_revision
  ARM: OMAP2+: Remove apply_uV constraints for fixed regulator
  ARM: OMAP: irqs: Fix NR_IRQS value to handle PRCM interrupts

Pull regulator fix from Mark Brown:
 "Another small, clear fix in a specific driver."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: tps65910: Configure correct value for VDDCTRL vout reg

Pull minor devicetree bug fixes and documentation updates from Grant Likely:
 "Fixes up a duplicate #include, adds an empty implementation of
  of_find_compatible_node() and make git ignore .dtb files.  And fix up
  bus name on OF described PHYs.  Nothing exciting here."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  doc: dt: Fix broken reference in gpio-leds documentation
  of/mdio: fix fixed link bus name
  of/fdt.c: asm/setup.h included twice
  of: add picochip vendor prefix
  dt: add empty of_find_compatible_node function
  ARM: devicetree: Add .dtb files to arch/arm/boot/.gitignore

Pull SPI section mismatch bug fix for v3.3-rc3 from Grant Likely:
 "Minor fix for pl022_dma_probe() function which was put in the wrong
  section."

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  Fix section mismatch in spi-pl022.c

Pull four hwmon patches from Guenter Roeck

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (jc42) Add support for AT30TS00, TS3000GB2, TSE2002GB2, and MCP9804
  hwmon: (zl6100) Maintain delay parameter in driver instance data
  hwmon: (pmbus_core) Fix maximum number of POUT alarm attributes
  hwmon: (jc42) Add support for ST Microelectronics STTS2002 and STTS3000

Pull device-mapper fixes for 3.3 from Alasdair Kergon

Eight small device-mapper bug fixes.

* tag 'dm-3.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm raid: fix flush support
  dm raid: set MD_CHANGE_DEVS when rebuilding
  dm thin metadata: decrement counter after removing mapped block
  dm thin metadata: unlock superblock in init_pmd error path
  dm thin metadata: remove incorrect close_device on creation error paths
  dm flakey: fix crash on read when corrupt_bio_byte not set
  dm io: fix discard support
  dm ioctl: do not leak argv if target message only contains whitespace

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Olaf Hering <olaf@aepfle.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix module build errors with CONFIG_OMAP4_ERRATA_I688
  ARM: OMAP: id: Add missing break statement in omap3xxx_check_revision
  ARM: OMAP2+: Remove apply_uV constraints for fixed regulator
  ARM: OMAP: irqs: Fix NR_IRQS value to handle PRCM interrupts

Fixed following:
arch/arm/mach-s3c2440/s3c244x.c: In function 's3c244x_restart':
arch/arm/mach-s3c2440/s3c244x.c:209: error: expected declaration or statement at end of input
make[1]: *** [arch/arm/mach-s3c24xx/s3c244x.o] Error 1
make: *** [arch/arm/mach-s3c24xx] Error 2
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

snd_hdspm uses its own ioctls to acquire config- and status information.
Expose the corresponding ioctl handler via ioctl_compat, so that 32bit
applications can use it on 64bit kernels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This function is called from enable_iommus(), which in turn is used
from amd_iommu_resume().

Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>

All pre-SI chips are limited to 165 Mhz for single link.
Code in question will be re-enabled when SI support is added.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=44755
https://bugzilla.kernel.org/show_bug.cgi?id=42887Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

Mesa may set it to 1, causing all primitives to be killed.

v2: also update the r7xx code
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

|kernel BUG at kernel/rtmutex.c:724!
|[<c029599c>] (rt_spin_lock_slowlock+0x108/0x2bc) from [<c01c2330>] (defer_bh+0x1c/0xb4)
|[<c01c2330>] (defer_bh+0x1c/0xb4) from [<c01c3afc>] (rx_complete+0x14c/0x194)
|[<c01c3afc>] (rx_complete+0x14c/0x194) from [<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0)
|[<c01cac88>] (usb_hcd_giveback_urb+0xa0/0xf0) from [<c01e1ff4>] (musb_giveback+0x34/0x40)
|[<c01e1ff4>] (musb_giveback+0x34/0x40) from [<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0)
|[<c01e2b1c>] (musb_advance_schedule+0xb4/0x1c0) from [<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c)
|[<c01e2ca8>] (musb_cleanup_urb.isra.9+0x80/0x8c) from [<c01e2ed0>] (musb_urb_dequeue+0xec/0x108)
|[<c01e2ed0>] (musb_urb_dequeue+0xec/0x108) from [<c01cbb90>] (unlink1+0xbc/0xcc)
|[<c01cbb90>] (unlink1+0xbc/0xcc) from [<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8)
|[<c01cc2ec>] (usb_hcd_unlink_urb+0x54/0xa8) from [<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58)
|[<c01c2a84>] (unlink_urbs.isra.17+0x2c/0x58) from [<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c)
|[<c01c2b44>] (usbnet_terminate_urbs+0x94/0x10c) from [<c01c2d68>] (usbnet_stop+0x100/0x15c)
|[<c01c2d68>] (usbnet_stop+0x100/0x15c) from [<c020f718>] (__dev_close_many+0x94/0xc8)

defer_bh() takes the lock which is hold during unlink_urbs(). The safe
walk suggest that the skb will be removed from the list and this is done
by defer_bh() so it seems to be okay to drop the lock here.

Cc: stable@kernel.org
Reported-by: Aníbal Almeida Pinto <anibal.pinto@efacec.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As we invalidate the inetpeer tree along with the routing cache now,
we don't need a genid to reset the redirect handling when the routing
cache is flushed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We initialize the routing metrics with the values cached on the
inetpeer in rt_init_metrics(). So if we have the metrics cached on the
inetpeer, we ignore the user configured fib_metrics.

To fix this issue, we replace the old tree with a fresh initialized
inet_peer_base. The old tree is removed later with a delayed work queue.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.

Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop.  The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now we have:
eth0: link *down*
br0: port 1(eth0) entered *forwarding* state

br_log_state(p) should be called *after* p->state is set
to BR_STATE_DISABLED.
Reported-by: Zilvinas Valinskas <zilvinas@wilibox.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When br_log_state() is reporting state it should say "entered"
istead of "entering" since state at this point is already
changed.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 239c562c (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When modifying IP addresses or ports on a UDP packet we don't
correctly follow the rules for unchecksummed packets.  This meant
that packets without a checksum can be given a incorrect new checksum
and packets with a checksum can become marked as being unchecksummed.
This fixes it to handle those requirements.
Signed-off-by: Jesse Gross <jesse@nicira.com>

As per datasheet, the voltage output is defined as
from SEL[6:0] = 3 to 64 (dec)
Vout= (SEL[6:0] × 12.5 mV + 562.5 mV)

The list_voltage returns the vout as
    600mV +  selector * 12.5mV

and so equivalent VSEL is selector + 3.
Adding 3 on selector when configuring VSEL register for
VDDCTRL output.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix dm-raid flush support.

Both md and dm have support for flush, but the dm-raid target
forgot to set the flag to indicate that flushes should be
passed on.  (Important for data integrity e.g. with writeback cache
enabled.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

The 'rebuild' parameter is used to rebuild individual devices in an
array (e.g. resynchronize a RAID1 device or recalculate a parity device
in higher RAID).  The MD_CHANGE_DEVS flag must be set when this
parameter is given in order to write out the superblocks and make the
change take immediate effect.  The code that handles new devices in
super_load already sets MD_CHANGE_DEVS and 'FirstUse'.  (The 'FirstUse'
flag was being set as a special case for rebuilds in
super_init_validation.)

Add a condition for rebuilds in super_load to take care of both flags
without the special case in 'super_init_validation'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>