Bjarni Jonasson says:

====================
Fixes applied to VCS8584 family

Three different fixes applied to VSC8584 family:
1. LCPLL reset
2. Serdes calibration
3. Coma mode disabled

The same fixes has already been applied to VSC8514
and most of the functionality can be reused for the VSC8584.

v1 -> v2:
  Preserved reversed christmas tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch releases coma mode for VSC8584 as done for VSC8514 in
commit ca0d7fd0 ("net: phy: mscc: coma mode disabled for VSC8514")

Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduced 'FOJI' serdes calibration in commit 85e97f0b
("net: phy: mscc: improved serdes calibration applied to VSC8514")
Now including the VSC8584 family.

Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduced LCPLL reset in
commit d15e08d9fb82 ("net: phy: mscc: adding LCPLL reset to VSC8514").
Now applying this reset to the VSC8584 phy familiy.

Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael reports that after the blamed patch, unbinding a VF would cause
these transactions to remain pending, and trigger some warnings with the
DMA API debug:

$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 19
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0

$ echo 0 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
DMA-API: pci 0000:00:01.0: device driver has pending DMA allocations while released from device [count=1]
One of leaked entries details: [size=2048 bytes] [mapped with DMA_BIDIRECTIONAL] [mapped as coherent]
WARNING: CPU: 0 PID: 2547 at kernel/dma/debug.c:853 dma_debug_device_change+0x174/0x1c8
(...)
Call trace:
 dma_debug_device_change+0x174/0x1c8
 blocking_notifier_call_chain+0x74/0xa8
 device_release_driver_internal+0x18c/0x1f0
 device_release_driver+0x20/0x30
 pci_stop_bus_device+0x8c/0xe8
 pci_stop_and_remove_bus_device+0x20/0x38
 pci_iov_remove_virtfn+0xb8/0x128
 sriov_disable+0x3c/0x110
 pci_disable_sriov+0x24/0x30
 enetc_sriov_configure+0x4c/0x108
 sriov_numvfs_store+0x11c/0x198
(...)
DMA-API: Mapped at:
 dma_entry_alloc+0xa4/0x130
 debug_dma_alloc_coherent+0xbc/0x138
 dma_alloc_attrs+0xa4/0x108
 enetc_setup_cbdr+0x4c/0x1d0
 enetc_vf_probe+0x11c/0x250
pci 0000:00:01.0: Removing from iommu group 19

This happens because stupid me moved enetc_teardown_cbdr outside of
enetc_free_si_resources, but did not bother to keep calling
enetc_teardown_cbdr from all the places where enetc_free_si_resources
was called. In particular, now it is no longer called from the main
unbind function, just from the probe error path.

Fixes: 4b47c0b8 ("net: enetc: don't initialize unused ports from a separate code path")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in an error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.

Fixes: d8ce30e0 ("octeontx2-pf: add tc flower stats handler for hw offloads")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the lower_32_bits/upper_32_bits macros to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/huawei/hinic/hinic_hw_mgmt.c: In function ‘mgmt_recv_msg_handler’:
drivers/net/ethernet/huawei/hinic/hinic_hw_mgmt.c:443:18: warning: unused variable ‘pdev’ [-Wunused-variable]
  443 |  struct pci_dev *pdev = pf_to_mgmt->hwif->pdev;
      |                  ^~~~
Signed-off-by: David S. Miller <davem@davemloft.net>

Daode Huang says:

====================
net: hinic; make some cleanup for hinic

This set try to remove the unnecessary output message, add a blank line,
remove the dupliate word and change the deprecated strlcp functions in
hinic driver, for details, please refer to each patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Usage of strlcpy in linux kernel has been recently
deprecated[1], so convert hinic driver to strscpy

[1] https://lore.kernel.org/lkml/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL
=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Daode Huang <huangdaode@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a duplicate "the" in the comment, so delete it.
Signed-off-by: Daode Huang <huangdaode@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There should be a blank line after declarations, so just add it.
Signed-off-by: Daode Huang <huangdaode@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unnecessary out of memory message in hinic driver,
fixes the following checkpatch.pl warning:
"WARNING: Possible unnecessary 'out of memory' message"
Signed-off-by: Daode Huang <huangdaode@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using napi_alloc_skb in NAPI context avoids enable/disable IRQs, which
increases iperf3 result by a few Mbps. Since napi_alloc_skb() uses
NET_IP_ALIGN, convert other alloc methods to the same padding. Tested
on Intel Core2 and AMD K10 platforms.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing to napi_gro_receive() improves efficiency significantly. Tested
on Intel Core2-based motherboards and iperf3.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here is what Vladimir says about it:

  at803x_aneg_done() keeps the aneg reporting as "not done" even when
  the copper-side link was reported as up, but the in-band autoneg has
  not finished.

  That was the _intended_ behavior when that code was introduced, and
  Heiner have said about it [1]:

  | That's not nice from the PHY:
  | It signals "link up", and if the system asks the PHY for link details,
  | then it sheepishly says "well, link is *almost* up".

  If the specification of phy_aneg_done behavior does not include
  in-band autoneg (and it doesn't), then this piece of code does not
  belong here.

  The fact that we can no longer trigger this code from phylib is yet
  another reason why it fails at its intended (and wrong) purpose and
  should be removed.

Removing the SGMII link check, would just keep the call to
genphy_aneg_done(), which is also the fallback. Thus we can just remove
at803x_aneg_done() altogether.

[1] https://lore.kernel.org/netdev/fdf0074a-2572-5914-6f3e-77202cbf96de@gmail.com/Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using short intervals e.g. below one millisecond, large packets won't be
transmitted at all. The software implementations checks whether the packet can
be fit into the remaining interval. Therefore, it takes the packet length and
the transmission speed into account. That is correct.

However, for large packets it may be that the transmission time exceeds the
interval resulting in no packet transmission. The same situation works fine with
hardware offloading applied.

The problem has been observed with the following schedule and iperf3:

|tc qdisc replace dev lan1 parent root handle 100 taprio \
|   num_tc 8 \
|   map 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 \
|   queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
|   base-time $base \
|   sched-entry S 0x40 500000 \
|   sched-entry S 0xbf 500000 \
|   clockid CLOCK_TAI \
|   flags 0x00

[...]

|root@tsn:~# iperf3 -c 192.168.2.105
|Connecting to host 192.168.2.105, port 5201
|[  5] local 192.168.2.121 port 52610 connected to 192.168.2.105 port 5201
|[ ID] Interval           Transfer     Bitrate         Retr  Cwnd
|[  5]   0.00-1.00   sec  45.2 KBytes   370 Kbits/sec    0   1.41 KBytes
|[  5]   1.00-2.00   sec  0.00 Bytes  0.00 bits/sec    0   1.41 KBytes

After debugging, it seems that the packet length stored in the SKB is about
7000-8000 bytes. Using a 100 Mbit/s link the transmission time is about 600us
which larger than the interval of 500us.

Therefore, segment the SKB into smaller chunks if the packet is too big. This
yields similar results than the hardware offload:

|root@tsn:~# iperf3 -c 192.168.2.105
|Connecting to host 192.168.2.105, port 5201
|- - - - - - - - - - - - - - - - - - - - - - - - -
|[ ID] Interval           Transfer     Bitrate         Retr
|[  5]   0.00-10.00  sec  48.9 MBytes  41.0 Mbits/sec    0             sender
|[  5]   0.00-10.02  sec  48.7 MBytes  40.7 Mbits/sec                  receiver

Furthermore, the segmentation can be skipped for the full offload case, as the
driver or the hardware is expected to handle this.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/verfied/verified/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Lobakin says:

====================
net: avoid retpoline overhead on VLAN and TEB GRO

dev_gro_receive() uses indirect calls for IP GRO functions, but
it works only for the outermost headers and untagged frames.
Simple VLAN tag before an IP header restores the performance hit.
This simple series straightens the GRO calls for IP headers going
after VLAN tag or inner Ethernet header (GENEVE, NvGRE, VxLAN)
for retpolined kernels.
====================

The two most popular headers going after Ethernet are IPv4 and IPv6.
Retpoline overhead for them is addressed only in dev_gro_receive(),
when they lie right after the outermost Ethernet header.
Use the indirect call wrappers in TEB (Transparent Ethernet Bridging,
such as GENEVE, NvGRE, VxLAN etc.) GRO receive code to reduce the
penalty when processing the inner headers.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two most popular headers going after VLAN are IPv4 and IPv6.
Retpoline overhead for them is addressed only in dev_gro_receive(),
when they lie right after the outermost Ethernet header.
Use the indirect call wrappers in VLAN GRO receive code to reduce
the penalty on receiving tagged frames (when hardware stripping is
off or not available).
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

call_gro_receive() is used to limit GRO recursion, but it works only
with callback pointers.
There's a combined version of call_gro_receive() + INDIRECT_CALL_2()
in <net/inet_common.h>, but it doesn't check for IPv6 modularity.
Add a similar new helper to cover both of these. It can and will be
used to avoid retpoline overhead when IP header lies behind another
offloaded proto.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

If some source file includes <net/gro.h>, but doesn't include
<linux/indirect_call_wrapper.h>:

In file included from net/8021q/vlan_core.c:7:
./include/net/gro.h:6:1: warning: data definition has no type or storage class
    6 | INDIRECT_CALLABLE_DECLARE(struct sk_buff *ipv6_gro_receive(struct list_head *,
      | ^~~~~~~~~~~~~~~~~~~~~~~~~
./include/net/gro.h:6:1: error: type defaults to ‘int’ in declaration of ‘INDIRECT_CALLABLE_DECLARE’ [-Werror=implicit-int]

[...]

Include <linux/indirect_call_wrapper.h> directly. It's small and
won't pull lots of dependencies.
Also add some incomplete struct declarations to be fully stacked.

Fixes: 04f00ab2 ("net/core: move gro function declarations to separate header ")
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/serisouly/seriously/

...and the sentence construction.
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic fixes

These are a few little fixes and cleanups found while working
on other features and more testing.
====================

Don't destroy the adminq while there is an outstanding request.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up to now we've been ignoring any error return from the
queue starting in the link status check, so we fix that here.
If the driver had to reset and couldn't get things running
properly again, for example after a Tx Timeout and the FW is
not responding to commands, don't let the link watchdog try
to restart the queues.  At this point the user can try to DOWN
and UP the device to clear the errors.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Block some actions while the FW is in a reset activity
and the queues are not configured.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support in get_link_ksettings for a couple of
new BASET connections.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can get to the counter without going through the pointer
that the robot complained about.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qcq->intr.index was set when the queue was allocated,
there is no need to reach around to find it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Catch a couple of missing macro name uses, fix a couple
of misspellings, etc.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.

I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.

We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.

We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a MRP ring was deleted or disabled, the driver was iterating over
the ports to detect if any other MPR rings exists and in case it didn't
exist it would delete the MAC table entry. But the problem was that it
used the last iterated port to delete the MAC table entry and this could
be a NULL port.

The fix consists of using the port on which the function was called.

Fixes: 7c588c3e ("net: ocelot: Extend MRP")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a virtual LAPB device's underlying Ethernet device closes, the LAPB
device is also closed.

However, currently the LAPB device is closed after the Ethernet device
closes. It would be better to close it before the Ethernet device closes.
This would allow the LAPB device to transmit a last frame to notify the
other side that it is disconnecting.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointer pfvf is being initialized with a value that is
never read and it is being updated later with a new value.  The
initialization is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Fixes: 56bcef52 ("octeontx2-af: Use npc_install_flow API for promisc and broadcast entries")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver data for the data interface has already been set by
usb_driver_claim_interface() so drop the subsequent redundant
assignment.

Note that this also avoids setting the driver data three times in case
of a combined interface.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the return expression.
Signed-off-by: zuoqilin <zuoqilin@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A typo is found out by codespell tool in 1734th line of drop_monitor.c:

$ codespell ./net/core/
./net/core/drop_monitor.c:1734: guarnateed  ==> guaranteed

Fix a typo found by codespell.
Signed-off-by: Xiong Zhenwu <xiong.zhenwu@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>