Add IEEE80211_RADIOTAP_EHT and IEEE80211_RADIOTAP_EHT_USIG radiotap
to fill in EHT information, such as MCS, NSS, GI and bandwidth.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Introduce wifi LED switch control, add flow to Control a wifi
gpio pin based on the status of WIFI radio, if the pin is connected
to an LED, the LED will indicate the status of the WiFi radio.
Signed-off-by: Hao Zhang <hao.zhang@mediatek.com>
Co-developed-by: Quan Zhou <quan.zhou@mediatek.com>
Signed-off-by: Quan Zhou <quan.zhou@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The firmware support for management frame protection has limitations:
- do not support cipher BIP-GMAC-128 and BIP-GMAC-256
- support cipher BIP-CMAC-128 and BIP-CMAC-256, except action frame with
  action type 'not robust'.

Therefore, to simplify the logic, do not set the IGTK to firmware and
let the encryption of management frames be handled by upper layer.
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The implementation amounts to setting the driver flag
IEEE80211_VIF_SUPPORTS_CQM_RSSI, and then providing
mechanisms for continuously updating enough information
to be able to provide notifications to userspace when
RSSI drops below a certain threshold
Signed-off-by: Rong Yan <rong.yan@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Reduces size by avoiding duplicates
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This is expected by the firmware of older chipsets as well, though it may
not have been as strongly required as on mt799x

Fixes: 098428c4 ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Check if background radar is enabled or not before manually triggering it,
and also add more checks in radar detected event.
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For mt7992 chipsets, critical packet mode should be properly configured
to let the HW SDO module correctly fill the AC queue in TX descriptors of
some higher priority packets such as ARP and ICMP.
Without this patch, HW queues may hang when running MU traffic.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Without this commit, reading chip temperature will cause memory leakage.

Fixes: 6879b2e9 ("wifi: mt76: mt7996: add thermal sensor device support")
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not add UNI_BSS_INFO_11V_MBSSID tag when bssid_indicator is not set
to avoid abnormal beaconing behavior in non-11v MBSS scenario.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

For mt7996 chipsets, the HW CSO module can help to identify TCP traffic,
which assists the firmware in adjusting algorithms to improve overall
performance.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set RCPI values in mt7996_mcu_sta_rate_ctrl_tlv(), which can make the
FW rate control algorithm be initialized with a better MCS selection
table.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set peer address and aid for the BMC wtbl of station interface. For some
functions such as parsing MU_EDCA parameters from beacon, firmware will
need the peer address to do correct parsing.
Without this patch, MU uplink traffic would get suffered.
Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When a BMC wtbl of station interface is correctly set with peer address,
HW will do rx header translation for broadcast data packets, which makes
mac80211 unable to find the corresponding ieee80211_sta and drop the
packets. To fix this, disable HW rx header translation for BMC entry.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

of_gpio.h is deprecated and subject to remove.
The driver doesn't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Looks like this was missed in the initial patch that made
the conversion to the emulated chanctx drivers.

Fixes: 0a44dfc0 ("wifi: mac80211: simplify non-chanctx drivers")
Tested-by: James Courtier-Dutton <james.dutton@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Even if it is not a real issue at the moment since concurrent access to
mcu message queue is protected by mcu mutex, make the code more robust
and move mcu queue free space check inside queue spinlock critical section.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set intr1 to 0 in mt7996_irq_tasklet() in order to avoid possible
uninitialized variable usage if wed is not active for hif2.

Fixes: 83eafc92 ("wifi: mt76: mt7996: add wed tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Before sending suspend & wow command to FW, its length should be
4-bytes alignd.

Fixes: c948b5da ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.

This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

mt7920e is a mt7921 series chipset with 802.11ax 2x2:2SS support.
The major difference is in firmware side only, at this moment.
This patch would add some mandatory changes for new chip id and
firmware download control.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Fixes issues with scanning and low power output at some rates.

Fixes: f75e4779 ("wifi: mt76: mt7996: add txpower setting support")
Signed-off-by: Chad Monroe <chad@monroe.io>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The wcid can be NULL. It should be checked for validity before
dereferencing it to avoid crash.

Fixes: 098428c4 ("wifi: mt76: connac: set correct muar_idx for mt799x chipsets")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

This flag is needed for the PSE client reset. Fixes watchdog reset issues.

Fixes: c677dda1 ("wifi: mt76: mt7603: improve watchdog reset reliablity")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Use the correct WMM AC queue instead of the MGMT one to fix potential issues
with aggregation sequence number tracking. Drop non-bufferable packets.

Fixes: fca9615f ("mt76: mt7603: fix up hardware queue index for PS filtered packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When pre-calibration data is missing, do not fail the driver probe.
Instead, just print a warning and fall back to regular calibration.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Add pre-calibration for mt7986 and mt7916. It has different data size
with mt7915. Group cal needs 54k and 94k for 2G + 5G and 2G + 6G,
respectively. DPD cal needs 300k.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: StanleyYP Wang <StanleyYP.Wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Send an update to the MCU whenever the settings change
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The MT76_MCU_RESET flag is only read on the main phy.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The MT76_MCU_RESET flag is only read on the main phy.
Signed-off-by: Bo Jiao <Bo.Jiao@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Set correct beamformer capabilities for station vif in HE PHY
capabilities IE.
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Do not report measurements if the airtime counter was cleared since the
last update (possibly by firmware)
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

The mcu command format are different for mt7915 and mt7986.
Fix the mt7915_mcu_wed_wa_tx_stats to support mt7915 and mt7986.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Avoid potentially reusing uninitialized data
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Improves initial rate selection after connecting
Signed-off-by: Felix Fietkau <nbd@nbd.name>

Commit 3e2f544d ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.

Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240426093156.2002258-2-leitao@debian.org

With commit 34d21de9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.

With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.

Move qtnfmac driver to leverage the core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240426093156.2002258-1-leitao@debian.org

struct brcmf_usb_image was added in the initial commit 71bb244b
("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets") and updated
in commit 803599d4 ("brcmfmac: store usb fw images in local linked
list.")

Its only usage was removed in commit 52f98a57 ("brcmfmac: remove
firmware list from USB driver").

Remove the structure definition now. This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/23afd8c1733ad087ce2399a07a30d689aef861d5.1714039373.git.christophe.jaillet@wanadoo.fr

struct cb_del_ampdu_pars was added in the initial commit 5b435de0
("net: wireless: add brcm80211 drivers") and its only usage was removed in
commit e041f65d ("brcmsmac: Remove internal tx queue").

Remove the structure definition now. This saves a few lines of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/fa3b190b6e9cba65ecc36fc93121c6ed8704f704.1714036681.git.christophe.jaillet@wanadoo.fr