With commit e58e87ad ("powerpc/mm: Update _PAGE_KERNEL_RO") we
started using the ppp value 0b110 to map kernel readonly. But that
facility was only added as part of ISA 2.04. For earlier ISA version
only supported ppp bit value for readonly mapping is 0b011. (This
implies both user and kernel get mapped using the same ppp bit value for
readonly mapping.).
Update the code such that for earlier architecture version we use ppp
value 0b011 for readonly mapping. We don't differentiate between power5+
and power5 here and apply the new ppp bits only from power6 (ISA 2.05).
This keep the changes minimal.

This fixes issue with PS3 spu usage reported at
https://lkml.kernel.org/r/rep.1421449714.geoff@infradead.org

Fixes: e58e87ad ("powerpc/mm: Update _PAGE_KERNEL_RO")
Cc: stable@vger.kernel.org # v4.7+
Tested-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

When configured with CONFIG_PPC_EARLY_DEBUG_OPAL=y the kernel expects
the OPAL entry and base addresses to be passed in r8 and r9
respectively. Currently the wrapper does not attempt to restore these
values before entering the decompressed kernel which causes the kernel
to branch into whatever happens to be in r9 when doing a write to the
OPAL console in early boot.

This patch adds a platform_ops hook that can be used to branch into the
new kernel. The OPAL console driver patches this at runtime so that if
the console is used it will be restored just prior to entering the
kernel.

Fixes: 656ad58e ("powerpc/boot: Add OPAL console to epapr wrappers")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

After patch 4efca4ed ("kbuild: modversions for EXPORT_SYMBOL() for asm"),
asm exports can get modversions CRCs generated if they have C definitions
in asm-prototypes.h. This patch adds missing definitions for 32 and 64 bit
allmodconfig builds.

Fixes: 9445aa1a ("ppc: move exports to definitions")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

There is a new bit, LPCR_PECE_HVEE (Hypervisor Virtualization Exit
Enable), which controls wakeup from STOP states on Hypervisor
Virtualization Interrupts (which happen to also be all external
interrupts in host or bare metal mode).

It needs to be set or we will miss wakeups.

Fixes: 9baaef0a ("powerpc/irq: Add support for HV virtualization interrupts")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename it to HVEE to match the name in the ISA]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

We need to update on secondaries for the selected MMU mode.

Fixes: ad410674 ("powerpc/mm: Update the HID bit when switching from radix to hash")
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

On POWER9 DD1, when we do a local TLB invalidate we also need to explicitly
invalidate the ERAT.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit d3cbff1b "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.

This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()

Fixes: d3cbff1b ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since the KERN_CONT changes, the current code in show_instructions()
prints out a whole bunch of unnecessary newlines. Change occurrences of
printk("\n") to pr_cont("\n"). While we're here, change all the other
cases of printk(KERN_CONT ...) to pr_cont() as well.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix up our oops output by converting continuation lines to use
pr_cont(). Some of these are dubious, eg. printing a continuation line
which starts with a newline, but seem to work OK for now. This whole
function needs a rewrite in the next release.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since the KERN_CONT changes these are being horribly split across lines,
for example:

    MSR: 8000000000009033 <
    SF,EE
    ,ME,IR
    ,DR,RI
    ,LE>

So fix it by using pr_cont() where appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Previously we got away with printing the stack trace in multiple pieces
and it usually looked right.  But since commit 4bcc595c ("printk:
reinstate KERN_CONT for printing continuation lines"), KERN_CONT is now
required when printing continuation lines. Use pr_cont() as appropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The changes to use gas sections for constructing the exception vectors
causes a build break when using binutils 2.23:

  arch/powerpc/kernel/exceptions-64s.S:770: Error: operand out of range
  (0xffffffffffff8100 is not between 0x0000000000000000 and 0x000000000000ffff)

And so on.

Reported by Hugh with binutils-2.23.2-8.1.4.ppc64 from openSUSE 13.1 and
also Naveen & Denis using 2.23.52.0.1-26.el7 from RHEL 7. Strangely
binutils 2.22 (what I test with) is not affected.

This is caused by the use of @l in LOAD_HANDLER(). The @l was only
recently added in commit a24553dd ("powerpc/pseries: Remove
unnecessary syscall trampoline").

Luckily the gas section changes split out the LOAD_SYSCALL_HANDLER()
macro, which means we actually *don't* need to use @l in LOAD_HANDLER()
any more, only in LOAD_SYSCALL_HANDLER().

So drop the @l from LOAD_HANDLER().

Fixes: 57f26649 ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Hugh Dickins <hughd@google.com>
[mpe: Add gory details to change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Wakeups from winkle set the low bit of the HSPRG0 register, to
distinguish it from other sleep states. This is also the PACA pointer.
The system reset exception handler fails to mask this bit away before
using this value before using it as the PACA pointer.

Fix this by adding a new type of exception prolog macro where we already
have the PACA set in r13, and have the system reset vector mask it out.
The winkle wakeup handler will store the masked value back into HSPRG0.

Fixes: fb479e44 ("powerpc/64s: relocation, register save fixes for system reset interrupt")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch does a couple of things. First of all, powernv immediately
explodes when running a relocated kernel, because the system reset
exception for handling sleeps does not do correct relocated branches.

Secondly, the sleep handling code trashes the condition and cfar
registers, which we would like to preserve for debugging purposes (for
non-sleep case exception).

This patch changes the exception to use the standard format that saves
registers before any tests or branches are made. It adds the test for
idle-wakeup as an "extra" to break out of the normal exception path.
Then it branches to a relocated idle handler that calls the various
idle handling functions.

After this patch, POWER8 CPU simulator now boots powernv kernel that is
running at non-zero.

Fixes: 948cf67c ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Before this patch, we used tlbiel, if we ever ran only on this core.
That was mostly derived from the nohash usage of the same. But is
incorrect, the ISA 3.0 clarifies tlbiel such that:

"All TLB entries that have all of the following properties are made
invalid on the thread executing the tlbiel instruction"

ie. tlbiel only invalidates TLB entries on the current thread. So if the
mm has been used on any other thread (aka. cpu) then we must broadcast
the invalidate.

This bug could lead to invalid TLB entries if a program runs on multiple
threads of a core.

Hence use tlbiel, if we only ever ran on only the current cpu.

Fixes: 1a472c9d ("powerpc/mm/radix: Add tlbflush routines")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

It should be ALTIVEC, not ALIVEC.

Cyril explains: If a thread performs a transaction with altivec and then
gets preempted for whatever reason, this bug may cause the kernel to not
re-enable altivec when that thread runs again. This will result in an
altivec unavailable fault, when that fault happens inside a user
transaction the kernel has no choice but to enable altivec and doom the
transaction.

The result is that transactions using altivec may get aborted more often
than they should.

The difficulty in catching this with a selftest is my deliberate use of
the word may above. Optimisations to avoid FPU/altivec/VSX faults mean
that the kernel will always leave them on for 255 switches. This code
prevents the kernel turning it off if it got to the 256th switch (and
userspace was transactional).

Fixes: dc16b553 ("powerpc: Always restore FPU/VEC/VSX if hardware transactional memory in use")
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This fixes a race condition where one thread that is entering or
leaving a power-saving state can inadvertently ignore the lock bit
that was set by another thread, and potentially also clear it.
The core_idle_lock_held function is called when the lock bit is
seen to be set.  It polls the lock bit until it is clear, then
does a lwarx to load the word containing the lock bit and thread
idle bits so it can be updated.  However, it is possible that the
value loaded with the lwarx has the lock bit set, even though an
immediately preceding lwz loaded a value with the lock bit clear.
If this happens then we go ahead and update the word despite the
lock bit being set, and when called from pnv_enter_arch207_idle_mode,
we will subsequently clear the lock bit.

No identifiable misbehaviour has been attributed to this race.

This fixes it by checking the lock bit in the value loaded by the
lwarx.  If it is set then we just go back and keep on polling.

Fixes: b32aadc1 ("powerpc/powernv: Fix race in updating core_idle_state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 8117ac6a ("powerpc/powernv: Switch off MMU before entering
nap/sleep/rvwinkle mode", 2014-12-10) fixed a race condition where one
thread entering a KVM guest could switch the MMU context to the guest
while another thread was still in host kernel context with the MMU on.
That commit moved the point where a thread entering a power-saving
mode set its kvm_hstate.hwthread_state field in its PACA to
KVM_HWTHREAD_IN_IDLE from a point where the MMU was on to after the
MMU had been switched off.  That commit also added a comment
explaining that we have to switch to real mode before setting
hwthread_state to avoid this race.

Nevertheless, commit 4eae2c9a ("powerpc/powernv: Make
pnv_powersave_common more generic", 2016-07-08) subsequently moved
the setting of hwthread_state back to a point where the MMU is on,
thus reintroducing the race, despite the comment saying that this
should not be done being included in full in the context lines of
the patch that did it.

This fixes the race again and adds a bigger and shoutier comment
explaining the potential race condition.

Fixes: 4eae2c9a ("powerpc/powernv: Make pnv_powersave_common more generic")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Shreyas B. Prabhu <shreyasbp@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In some error paths in functions cxl_start_context and
afu_ioctl_start_work pid references to the current & group-leader tasks
can leak after they are taken. This patch fixes these error paths to
release these pid references before exiting the error path.

Fixes: 7b8ad495 ("cxl: Fix DSI misses when the context owning task exits")
Cc: stable@vger.kernel.org # v4.5+
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.

With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.

In this instance the code comes directly from ISA v2.07, including the
cmp, but cmpd is correct. Backport to stable so that new toolchains can
build old kernels.

Fixes: 948cf67c ("powerpc: Add NAP mode support on Power7 in HV mode")
Cc: stable@vger.kernel.org # v3.0
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 5d375199 ("KVM: PPC: Book3S HV: Set server for passed-through
interrupts") broke the SMP=n build:

  arch/powerpc/kvm/book3s_hv_rm_xics.c:758:2: error: implicit declaration of function 'get_hard_smp_processor_id'

That is because we lost the implicit include of asm/smp.h, so include it
explicitly to get the definition for get_hard_smp_processor_id().

Fixes: 5d375199 ("KVM: PPC: Book3S HV: Set server for passed-through interrupts")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Eliminates warning messages:

<stdin>:1316:2: warning: #warning syscall pkey_mprotect not implemented [-Wcpp]
<stdin>:1319:2: warning: #warning syscall pkey_alloc not implemented [-Wcpp]
<stdin>:1322:2: warning: #warning syscall pkey_free not implemented [-Wcpp]

Hopefully we will remember to revert this commit if we ever implement
them.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With recent update to printk, we get console output like below:

[    0.550639] Brought up 160 CPUs
[    0.550718] Node 0 CPUs:
[    0.550721]  0
[    0.550754] -39

[    0.550794] Node 1 CPUs:
[    0.550798]  40
[    0.550817] -79

[    0.550856] Node 16 CPUs:
[    0.550860]  80
[    0.550880] -119

[    0.550917] Node 17 CPUs:
[    0.550923]  120
[    0.550942] -159

Fix this by properly using pr_cont(), ie. KERN_CONT.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

At boot we dump the NUMA memory topology in dump_numa_memory_topology(),
at KERN_DEBUG level, resulting in output like:

  Node 0 Memory: 0x0-0x100000000
  Node 1 Memory: 0x100000000-0x200000000

Which is nice enough, but immediately after that we iterate over each
node and call setup_node_data(), which also prints out the node ranges,
at KERN_INFO, giving eg:

  numa: Initmem setup node 0 [mem 0x00000000-0xffffffff]
  numa: Initmem setup node 1 [mem 0x100000000-0x1ffffffff]

Additionally dump_numa_memory_topology() does not use KERN_CONT
correctly, resulting in split output lines on recent kernels.

So drop dump_numa_memory_topology() as superfluous chatter.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch prevents resetting the cxl adapter via sysfs in presence of
one or more active cxl_context on it. This protects against an
unrecoverable error caused by PSL owning a dirty cache line even after
reset and host tries to touch the same cache line. In case a force reset
of the card is required irrespective of any active contexts, the int
value -1 can be stored in the 'reset' sysfs attribute of the card.

The patch introduces a new atomic_t member named contexts_num inside
struct cxl that holds the number of active context attached to the card
, which is checked against '0' before proceeding with the reset. To
prevent against a race condition where a context is activated just after
reset check is performed, the contexts_num is atomically set to '-1'
after reset-check to indicate that no more contexts can be activated on
the card anymore.

Before activating a context we atomically test if contexts_num is
non-negative and if so, increment its value by one. In case the value of
contexts_num is negative then it indicates that the card is about to be
reset and context activation is error-ed out at that point.

Fixes: 62fa19d4 ("cxl: Add ability to reset the card")
Cc: stable@vger.kernel.org # v4.0+
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This commit broke boot on systems with an uncompressed kernel image,
namely systems using a cuImage. On such systems the compressed boot
image (boot wrapper, uncompressed kernel image, ..) is decompressed
by u-boot already, therefore the boot wrapper code sees an
uncompressed kernel image.

The old decompression code silently assumed an uncompressed kernel
image if it found no valid gzip signature, whilst the new code
bailed out in this case.

Fix this by re-introducing such a fallback if no valid compressed
image is found.

Fixes: 1b7898ee ("Use the pre-boot decompression API")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

If a cxl adapter faults on an invalid address for a kernel context, we
may enter copro_calculate_slb() with a NULL mm pointer (kernel
context) and an effective address which looks like a user
address. Which will cause a crash when dereferencing mm. It is clearly
an AFU bug, but there's no reason to crash either. So return an error,
so that cxl can ack the interrupt with an address error.

Fixes: 73d16a6e ("powerpc/cell: Move data segment faulting code out of cell platform")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull befs fixes from Luis de Bethencourt:
 "I recently took maintainership of the befs file system [0]. This is
  the first time I send you a git pull request, so please let me know if
  all the below is OK.

  Salah Triki and myself have been cleaning the code and fixing a few
  small bugs.

  Sorry I couldn't send this sooner in the merge window, I was waiting
  to have my GPG key signed by kernel members at ELCE in Berlin a few
  days ago."

[0] https://lkml.org/lkml/2016/7/27/502

* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
  befs: befs: fix style issues in datastream.c
  befs: improve documentation in datastream.c
  befs: fix typos in datastream.c
  befs: fix typos in btree.c
  befs: fix style issues in super.c
  befs: fix comment style
  befs: add check for ag_shift in superblock
  befs: dump inode_size superblock information
  befs: remove unnecessary initialization
  befs: fix typo in befs_sb_info
  befs: add flags field to validate superblock state
  befs: fix typo in befs_find_key
  befs: remove unused BEFS_BT_PARMATCH
  fs: befs: remove ret variable
  fs: befs: remove in vain variable assignment
  fs: befs: remove unnecessary *befs_sb variable
  fs: befs: remove useless initialization to zero
  fs: befs: remove in vain variable assignment
  fs: befs: Insert NULL inode to dentry
  fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
  ...

Pull gcc plugins update from Kees Cook:
 "This adds a new gcc plugin named "latent_entropy". It is designed to
  extract as much possible uncertainty from a running system at boot
  time as possible, hoping to capitalize on any possible variation in
  CPU operation (due to runtime data differences, hardware differences,
  SMP ordering, thermal timing variation, cache behavior, etc).

  At the very least, this plugin is a much more comprehensive example
  for how to manipulate kernel code using the gcc plugin internals"

* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  latent_entropy: Mark functions with __latent_entropy
  gcc-plugins: Add latent_entropy plugin

Pull MIPS updates from Ralf Baechle:
 "This is the main MIPS pull request for 4.9:

  MIPS core arch code:
   - traps: 64bit kernels should read CP0_EBase 64bit
   - traps: Convert ebase to KSEG0
   - c-r4k: Drop bc_wback_inv() from icache flush
   - c-r4k: Split user/kernel flush_icache_range()
   - cacheflush: Use __flush_icache_user_range()
   - uprobes: Flush icache via kernel address
   - KVM: Use __local_flush_icache_user_range()
   - c-r4k: Fix flush_icache_range() for EVA
   - Fix -mabi=64 build of vdso.lds
   - VDSO: Drop duplicated -I*/-E* aflags
   - tracing: move insn_has_delay_slot to a shared header
   - tracing: disable uprobe/kprobe on compact branch instructions
   - ptrace: Fix regs_return_value for kernel context
   - Squash lines for simple wrapper functions
   - Move identification of VP(E) into proc.c from smp-mt.c
   - Add definitions of SYNC barrierstype values
   - traps: Ensure full EBase is written
   - tlb-r4k: If there are wired entries, don't use TLBINVF
   - Sanitise coherentio semantics
   - dma-default: Don't check hw_coherentio if device is non-coherent
   - Support per-device DMA coherence
   - Adjust MIPS64 CAC_BASE to reflect Config.K0
   - Support generating Flattened Image Trees (.itb)
   - generic: Introduce generic DT-based board support
   - generic: Convert SEAD-3 to a generic board
   - Enable hardened usercopy
   - Don't specify STACKPROTECTOR in defconfigs

  Octeon:
   - Delete dead code and files across the platform.
   - Change to use all memory into use by default.
   - Rename upper case variables in setup code to lowercase.
   - Delete legacy hack for broken bootloaders.
   - Leave maintaining the link state to the actual ethernet/PHY drivers.
   - Add DTS for D-Link DSR-500N.
   - Fix PCI interrupt routing on D-Link DSR-500N.

  Pistachio:
   - Remove ANDROID_TIMED_OUTPUT from defconfig

  TX39xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  TX49xx:
   - Move GPIO setup from .mem_setup() to .arch_init()
   - Convert to Common Clock Framework

  txx9wdt:
   - Add missing clock (un)prepare calls for CCF

  BMIPS:
   - Add PW, GPIO SDHCI and NAND device node names
   - Support APPENDED_DTB
   - Add missing bcm97435svmb to DT_NONE
   - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
   - Add DT examples for BCM63268, BCM3368 and BCM6362
   - Add support for BCM3368 and BCM6362

  PCI
   - Reduce stack frame usage
   - Use struct list_head lists
   - Support for CONFIG_PCI_DOMAINS_GENERIC
   - Make pcibios_set_cache_line_size an initcall
   - Inline pcibios_assign_all_busses
   - Split pci.c into pci.c & pci-legacy.c
   - Introduce CONFIG_PCI_DRIVERS_LEGACY
   - Support generic drivers

  CPC
   - Convert bare 'unsigned' to 'unsigned int'
   - Avoid lock when MIPS CM >= 3 is present

  GIC:
   - Delete unused file smp-gic.c

  mt7620:
   - Delete unnecessary assignment for the field "owner" from PCI

  BCM63xx:
   - Let clk_disable() return immediately if clk is NULL

  pm-cps:
   - Change FSB workaround to CPU blacklist
   - Update comments on barrier instructions
   - Use MIPS standard lightweight ordering barrier
   - Use MIPS standard completion barrier
   - Remove selection of sync types
   - Add MIPSr6 CPU support
   - Support CM3 changes to Coherence Enable Register

  SMP:
   - Wrap call to mips_cpc_lock_other in mips_cm_lock_other
   - Introduce mechanism for freeing and allocating IPIs

  cpuidle:
   - cpuidle-cps: Enable use with MIPSr6 CPUs.

  SEAD3:
   - Rewrite to use DT and generic kernel feature.

  USB:
   - host: ehci-sead3: Remove SEAD-3 EHCI code

  FBDEV:
   - cobalt_lcdfb: Drop SEAD3 support

  dt-bindings:
   -  Document a binding for simple ASCII LCDs

  auxdisplay:
   - img-ascii-lcd: driver for simple ASCII LCD displays

  irqchip i8259:
   - i8259: Add domain before mapping parent irq
   - i8259: Allow platforms to override poll function
   - i8259: Remove unused i8259A_irq_pending

  Malta:
   - Rewrite to use DT

  of/platform:
   - Probe "isa" busses by default

  CM:
   - Print CM error reports upon bus errors

  Module:
   - Migrate exception table users off module.h and onto extable.h
   - Make various drivers explicitly non-modular:
   - Audit and remove any unnecessary uses of module.h

  mailmap:
   - Canonicalize to Qais' current email address.

  Documentation:
   - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API

  Loongson1C:
   - Add CPU support for Loongson1C
   - Add board support
   - Add defconfig
   - Add RTC support for Loongson1C board

  All this except one Documentation fix has sat in linux-next and has
  survived Imagination's automated build test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
  Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
  MIPS: ptrace: Fix regs_return_value for kernel context
  MIPS: VDSO: Drop duplicated -I*/-E* aflags
  MIPS: Fix -mabi=64 build of vdso.lds
  MIPS: Enable hardened usercopy
  MIPS: generic: Convert SEAD-3 to a generic board
  MIPS: generic: Introduce generic DT-based board support
  MIPS: Support generating Flattened Image Trees (.itb)
  MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
  MIPS: Print CM error reports upon bus errors
  MIPS: Support per-device DMA coherence
  MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
  MIPS: Sanitise coherentio semantics
  MIPS: PCI: Support generic drivers
  MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
  MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
  MIPS: PCI: Inline pcibios_assign_all_busses
  MIPS: PCI: Make pcibios_set_cache_line_size an initcall
  MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
  MIPS: PCI: Use struct list_head lists
  ...

Pull sound fixes from Takashi Iwai:
 "Just a few trivial small fixes"

* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: line6: fix a crash in line6_hwdep_write()
  ALSA: seq: fix passing wrong pointer in function call of compatibility layer
  ALSA: hda - Fix a failure of micmute led when having multi adcs
  ALSA: line6: Fix POD X3 Live audio input

Pull more misc uaccess and vfs updates from Al Viro:
 "The rest of the stuff from -next (more uaccess work) + assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  score: traps: Add missing include file to fix build error
  fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
  fs/super.c: fix race between freeze_super() and thaw_super()
  overlayfs: Fix setting IOP_XATTR flag
  iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
  blackfin: no access_ok() for __copy_{to,from}_user()
  arm64: don't zero in __copy_from_user{,_inatomic}
  arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
  arc: don't leak bits of kernel stack into coredump
  alpha: get rid of tail-zeroing in __copy_user()

Pull cifs fixes from Steve French:
 "Including:

   - nine bug fixes for stable. Some of these we found at the recent two
     weeks of SMB3 test events/plugfests.

   - significant improvements in reconnection (e.g. if server or network
     crashes) especially when mounted with "persistenthandles" or to
     server which advertises Continuous Availability on the share.

   - a new mount option "idsfromsid" which improves POSIX compatibility
     in some cases (when winbind not configured e.g.) by better (and
     faster) fetching uid/gid from acl (when "cifsacl" mount option is
     enabled). NB: we are almost complete work on "cifsacl" (querying
     mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
     not included in this set.

   - improved handling for SMB3 "credits" (even if server is buggy)

  Still working on two sets of changes:

   - cifsacl enablement for SMB3

   - cleanup of RFC1001 length calculation (so we can handle encryption
     and multichannel and RDMA)

  And a couple of new bugs were reported recently (unrelated to above)
  so will probably have another merge request next week"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
  CIFS: Retrieve uid and gid from special sid if enabled
  CIFS: Add new mount option to set owner uid and gid from special sids in acl
  CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
  CIFS: Fix persistent handles re-opening on reconnect
  SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
  SMB2: Separate Kerberos authentication from SMB2_sess_setup
  Expose cifs module parameters in sysfs
  Cleanup missing frees on some ioctls
  Enable previous version support
  Do not send SMB3 SET_INFO request if nothing is changing
  SMB3: Add mount parameter to allow user to override max credits
  fs/cifs: reopen persistent handles on reconnect
  Clarify locking of cifs file and tcon structures and make more granular
  Fix regression which breaks DFS mounting
  fs/cifs: keep guid when assigning fid to fileinfo
  SMB3: GUIDs should be constructed as random but valid uuids
  Set previous session id correctly on SMB3 reconnect
  cifs: Limit the overall credit acquired
  Display number of credits available
  Add way to query creation time of file via cifs xattr
  ...

Pull btrfs fixes from Chris Mason:
 "Some fixes from Omar and Dave Sterba for our new free space tree.

  This isn't heavily used yet, but as we move toward making it the new
  default we wanted to nail down an endian bug"

* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: tests: uninline member definitions in free_space_extent
  btrfs: tests: constify free space extent specs
  Btrfs: expand free space tree sanity tests to catch endianness bug
  Btrfs: fix extent buffer bitmap tests on big-endian systems
  Btrfs: catch invalid free space trees
  Btrfs: fix mount -o clear_cache,space_cache=v2
  Btrfs: fix free space tree bitmaps on big-endian systems

score images fail to build as follows.

arch/score/kernel/traps.c: In function 'show_stack':
arch/score/kernel/traps.c:55:3: error:
	implicit declaration of function '__get_user'

__get_user() is declared in asm/uaccess.h, which was previously included
through asm/module.h.

Cc: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 88dd4a74 ("score: separate extable.h, switch module.h to it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c99
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().

xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull overlayfs updates from Miklos Szeredi:
 "This update contains fixes to the "use mounter's permission to access
  underlying layers" area, and miscellaneous other fixes and cleanups.

  No new features this time"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: use vfs_get_link()
  vfs: add vfs_get_link() helper
  ovl: use generic_readlink
  ovl: explain error values when removing acl from workdir
  ovl: Fix info leak in ovl_lookup_temp()
  ovl: during copy up, switch to mounter's creds early
  ovl: lookup: do getxattr with mounter's permission
  ovl: copy_up_xattr(): use strnlen

Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.

In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>