This fixes a seg fault on 'ethtool -A' entry if the
interface is down.  Obviously we need to have the
phy device initialized / "connected" (see of_phy_connect())
to be able to advertise pause frame capabilities.

Fixes: 23402bddSigned-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This patch series contains following fixes -

* Fix memory leak caused because of issuing mailbox
  command which can not wait for its completion.
* Reset firmware API lock which might be in inconsistent state.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

o In case QLC_83XX_MBX_CMD_NO_WAIT command type the calling
  function does not free the memory as it does not wait for
  response. So free it when get a response from adapter after
  sending the command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some firmware versions fails to reset the lock during
initialization. Force reset firmware API lock during driver
probe to ensure lock availability.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two breaks missing there. The result is that userspace
receives multiple messages which might be confusing.

Introduced-by: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

I was told that the Cadence macb driver is also useful on Microblaze.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Redefine some macros that were conditioned upon SMC_DEBUG level.

By allowing compiler to verify parameters used by these macros
unconditionally, we can flag compilation failures.

Compiler will still optimize out the unused code path depending on
SMC_DEBUG, so this is a net gain.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

exisiting BPF verifier allows uninitialized access to registers,
'ret A' is considered to be a valid filter.
So initialize A and X to zero to prevent leaking kernel memory
In the future BPF verifier will be rejecting such filters
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In ksz9021_load_values_from_of() val2 to val4 aren't tested against their
initialization value.
This causes the test to always succeed, and this value to be used as if it
was loaded from the devicetree instead of being ignored, in case of a
missing/invalid property in the ethernet OF device node.
As a result, the value "0" is written to the relevant registers.

Change the conditions to test against the right initialization value.
Signed-off-by: Hubert Chaumette <hchaumette@adeneo-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A label just before a brace needs a following semicolon (empty statement).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When SMC_DEBUG >= 2, we hit the following compilation error:

drivers/net/ethernet/smsc/smc91x.c:85:0:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_findirq’:
drivers/net/ethernet/smsc/smc91x.c:1784:9: error: ‘dev’ undeclared (first use in this function)
  DBG(2, dev, "%s: %s\n", CARDNAME, __func__);
         ^
Fix it by passing in the appropriate netdev pointer.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds phy_found error path when there is no phy device
and changes bus_name.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves cksum_ctl to tx_rd_des23 from cksum_pktlen for correct checksum
offloading and modifies size for Tx/Rx descriptor.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Execute "ethtool -L eth0 combined 0" in guest, if multiqueue
is enabled, virtnet_send_command() will return -EINVAL error,
there is a validation in QEMU.

But if multiqueue is disabled, virtnet_set_queues() will just
return zero (success). We should return error for this situation.
Signed-off-by: Amos Kong <akong@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.

Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The caller needs capabilities on the namespace being queried, not on
their own namespace.  This is a security bug, although it likely has
only a minor impact.

Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mail address for Siva Reddy Kallam is bouncing, remove the email
address from the MAINTAINERS entry for Samsung's SXGBE driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e1000e, igb, ixgbe and i40e.

Most notably are Jakub's patches to clean up the Rx time stamping
code for ixgbe and the fix up of debug messages with proper termination.

Jesse's i40e patch fixes an issue reported by Eric Dumazet that the
i40e driver was allowing the hardware to replicate the PSH flag on
all segments of a TSO operation.  With this fix, we are now configuring
the CWR bit to only be set in the first packet of a TSO and we
enable TSO_ECN in order to advertise to the stack that we do the right
thing on the wire.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fix from Ingo Molnar:
 "This fixes the preemption-count imbalance crash reported by Owen
  Kibel"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce: Fix CMCI preemption bugs

Pull scheduler fixes from Ingo Molnar:
 "Two fixes:

   - a SCHED_DEADLINE task selection fix
   - a sched/numa related lockdep splat fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Check for stop task appearance when balancing happens
  sched/numa: Fix task_numa_free() lockdep splat

Pull perf fixes from Ingo Molnar:
 "Two kernel side fixes:

   - an Intel uncore PMU driver potential crash fix
   - a kprobes/perf-call-graph interaction fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Use rdmsrl_safe() when initializing RAPL PMU
  kprobes/x86: Fix page-fault handling logic

Pull drm fixes from Dave Airlie:
 "Unfortunately this contains no easter eggs, its a bit larger than I'd
  like, but I included a patch that just moves code from one file to
  another and I'd like to avoid merge conflicts with that later, so it
  makes it seem worse than it is,

  Otherwise:
   - radeon: fixes to use new microcode to stabilise some cards, use
     some common displayport code, some runtime pm fixes, pll regression
     fixes
   - i915: fix for some context oopses, a warn in a used path, backlight
     fixes
   - nouveau: regression fix
   - omap: a bunch of fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (51 commits)
  drm: bochs: drop unused struct fields
  drm: bochs: add power management support
  drm: cirrus: add power management support
  drm: Split out drm_probe_helper.c from drm_crtc_helper.c
  drm/plane-helper: Don't fake-implement primary plane disabling
  drm/ast: fix value check in cbr_scan2
  drm/nouveau/bios: fix a bit shift error introduced by 457e77b2
  drm/radeon/ci: make sure mc ucode is loaded before checking the size
  drm/radeon/si: make sure mc ucode is loaded before checking the size
  drm/radeon: improve PLL params if we don't match exactly v2
  drm/radeon: memory leak on bo reservation failure. v2
  drm/radeon: fix VCE fence command
  drm/radeon: re-enable mclk dpm on R7 260X asics
  drm/radeon: add support for newer mc ucode on CI (v2)
  drm/radeon: add support for newer mc ucode on SI (v2)
  drm/radeon: apply more strict limits for PLL params v2
  drm/radeon: update CI DPM powertune settings
  drm/radeon: fix runpm handling on APUs (v4)
  drm/radeon: disable mclk dpm on R7 260X
  drm/tegra: Remove gratuitous pad field
  ...

Add \n at the end of messages where missing, remove all \r.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Time stamping resources are per-interface so there is no need
to keep separate last_rx_timestamp for each Rx ring, move
last_rx_timestamp to the adapter structure.

With last_rx_timestamp inside adapter, ixgbe_ptp_rx_hwtstamp()
inline function is reduced to a single if statement so it is
no longer necessary. If statement is placed directly in
ixgbe_process_skb_fields() fixing likely/unlikely marking.

Checks for q_vector or adapter to be NULL are superfluous.

Comment about taking I/O hit is a leftover from previous design.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

RQDPC on i210/i211 is R/W not ReadClear. Clear after reading.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Some i2c fixes over DisplayPort.

* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: Improve vramlimit module param documentation
  drm/radeon: fix audio pin counts for DCE6+ (v2)
  drm/radeon/dp: switch to the common i2c over aux code
  drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
  drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
  drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
  drm/i915: support address only i2c-over-aux transactions
  drm/tegra: dp: Support address-only I2C-over-AUX transactions

Fix following compilation warning:
drivers/net/ethernet/intel/e1000e/netdev.c:6238:12: warning
‘e1000e_pm_thaw’ defined but not used [-Wunused-function]
 static int e1000e_pm_thaw(struct device *dev)
            ^
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When changing the interface mtu, the driver starts with a value
that doesn't include VLAN_HLEN.  Later tests in the driver
set the rx_buffer_len based on the mtu.  As a result, when
the user increases the mtu to 1504 (to support 802.1AD for example),
the driver rx_buffer_len does not change and frames longer
the 1522 bytes are rejected as too long.

Include VLAN_HLEN from the start so that an user mtu greater then
1500 bytes is correctly reflected in the driver rx_buffer_len.

CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull more networking fixes from David Miller:

 1) Fix mlx4_en_netpoll implementation, it needs to schedule a NAPI
    context, not synchronize it.  From Chris Mason.

 2) Ipv4 flow input interface should never be zero, it should be
    LOOPBACK_IFINDEX instead.  From Cong Wang and Julian Anastasov.

 3) Properly configure MAC to PHY connection in mvneta devices, from
    Thomas Petazzoni.

 4) sys_recv should use SYSCALL_DEFINE.  From Jan Glauber.

 5) Tunnel driver ioctls do not use the correct namespace, fix from
    Nicolas Dichtel.

 6) Fix memory leak on seccomp filter attach, from Kees Cook.

 7) Fix lockdep warning for nested vlans, from Ding Tianhong.

 8) Crashes can happen in SCTP due to how the auth_enable value is
    managed, fix from Vlad Yasevich.

 9) Wireless fixes from John W Linville and co.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (45 commits)
  net: sctp: cache auth_enable per endpoint
  tg3: update rx_jumbo_pending ring param only when jumbo frames are enabled
  vlan: Fix lockdep warning when vlan dev handle notification
  seccomp: fix memory leak on filter attach
  isdn: icn: buffer overflow in icn_command()
  ip6_tunnel: use the right netns in ioctl handler
  sit: use the right netns in ioctl handler
  ip_tunnel: use the right netns in ioctl handler
  net: use SYSCALL_DEFINEx for sys_recv
  net: mdio-gpio: Add support for separate MDI and MDO gpio pins
  net: mdio-gpio: Add support for active low gpio pins
  net: mdio-gpio: Use devm_ functions where possible
  ipv4, route: pass 0 instead of LOOPBACK_IFINDEX to fib_validate_source()
  ipv4, fib: pass LOOPBACK_IFINDEX instead of 0 to flowi4_iif
  mlx4_en: don't use napi_synchronize inside mlx4_en_netpoll
  net: mvneta: properly configure the MAC <-> PHY connection in all situations
  net: phy: add minimal support for QSGMII PHY
  sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)
  mwifiex: fix hung task on command timeout
  mwifiex: process event before command response
  ...

Pull cifs fixes from Steve French:
 "A set of 5 small cifs fixes"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  cif: fix dead code
  cifs: fix error handling cifs_user_readv
  fs: cifs: remove unused variable.
  Return correct error on query of xattr on file with empty xattrs
  cifs: Wait for writebacks to complete before attempting write.

As reported by Eric Dumazet, the i40e driver was allowing the hardware
to replicate the PSH flag on all segments of a TSO operation.

This patch fixes the first/middle/last TCP flags settings which
makes the TSO operations work correctly.

With this change we are now configuring the CWR bit to only be set
in the first packet of a TSO, so this patch also enables TSO_ECN,
in order to advertise to the stack that we do the right thing
on the wire.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull char/misc driver fixes from Greg KH:
 "Here are a few driver fixes for char/misc drivers that resolve
  reported issues.

  All have been in linux-next successfully for a few days"

* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
  Tools: hv: Handle the case when the target file exists correctly
  vme_tsi148: Utilize to_pci_dev() macro
  vme_tsi148: Fix PCI address mapping assumption
  vme_tsi148: Fix typo in tsi148_slave_get()
  w1: avoid recursive device_add
  w1: fix netlink refcnt leak on error path
  misc: Grammar s/addition/additional/
  drivers: mcb: fix memory leak in chameleon_parse_cells() error path
  mei: ignore client writing state during cb completion
  mei: me: do not load the driver if the FW doesn't support MEI interface
  GenWQE: Increase driver version number
  GenWQE: Fix multithreading problems
  GenWQE: Ensure rc is not returning an uninitialized value
  GenWQE: Add wmb before DDCB is started
  GenWQE: Enable access to VPD flash area

Merge tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are some driver core fixes for 3.15-rc2.  Also in here are some
  documentation updates, as well as an API removal that had to wait for
  after -rc1 due to the cleanups coming into you from multiple developer
  trees (this one and the PPC tree.)

  All have been in linux next successfully"

* tag 'driver-core-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  drivers/base/dd.c incorrect pr_debug() parameters
  Documentation: Update stable address in Chinese and Japanese translations
  topology: Fix compilation warning when not in SMP
  Chinese: add translation of io_ordering.txt
  stable_kernel_rules: spelling/word usage
  sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()
  kernfs: protect lazy kernfs_iattrs allocation with mutex
  fs: Don't return 0 from get_anon_bdev

Pull staging driver fixes from Greg KH:
 "Here are a few staging driver fixes for issues that have been reported
  for 3.15-rc2.

  Also dominating the diffstat for the pull request is the removal of
  the rtl8187se driver.  It's no longer needed in staging as a "real"
  driver for this hardware is now merged in the tree in the "correct"
  location in drivers/net/

  All of these patches have been tested in linux-next"

* tag 'staging-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8188eu: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8712u: Fix case where ethtype was never obtained and always be checked against 0
  staging: r8188eu: Calling rtw_get_stainfo() with a NULL sta_addr will return NULL
  staging: comedi: fix circular locking dependency in comedi_mmap()
  staging: r8723au: Add missing initialization of change_inx in sort algorithm
  Staging: unisys: use after free in list_for_each()
  staging: unisys: use after free in error messages
  staging: speakup: fix misuse of kstrtol() in handle_goto()
  staging: goldfish: Call free_irq in error path
  staging: delete rtl8187se wireless driver
  staging: rtl8723au: Fix buffer overflow in rtw_get_wfd_ie()
  staging: gs_fpgaboot: remove __TIMESTAMP__ macro
  staging: vme: fix memory leak in vme_user_probe()
  staging: fpgaboot: clean up Makefile
  staging/usbip: fix store_attach() sscanf return value check
  staging/usbip: userspace - fix usbipd SIGSEGV from refresh_exported_devices()
  staging: rtl8188eu: remove spaces, correct counts to unbreak P2P ioctls
  staging/rtl8821ae: Fix OOM handling in _rtl_init_deferred_work()

Pull tty/serial driver fixes from Greg KH:
 "Here are a number of small tty/serial driver fixes for 3.15-rc2.  Also
  in here are some Documentation file removals for drivers that we
  removed a long time ago, no need to keep it around any longer.

  All of these have been in linux-next for a bit"

* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "serial: 8250, disable "too much work" messages"
  serial: amba-pl011: fix regression, causing an Oops on rmmod
  tty: Fix help text of SYNCLINK_CS
  tty: fix memleak in alloc_pid
  ttyprintk: Allow built as a module
  ttyprintk: Fix wrong tty_unregister_driver() call in the error path
  serial: 8250, disable "too much work" messages
  Documentation/serial: Delete obsolete driver documentation
  serial: omap: Fix missing pm_runtime_resume handling by simplifying code
  serial_core: Fix pm imbalance on unbind
  serial: pl011: change Rx burst size to half of trigger level
  serial: timberdale: Depend on X86_32
  serial: st-asc: Fix SysRq char handling
  Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
  serial_core: Fix conditional start_tx on ring buffer not empty
  serial: efm32: use $vendor,$device scheme for compatible string
  serial: omap: free the wakeup settings in remove

Pull USB fixes from Greg KH:
 "Here are a number of tiny USB fixes and new device ids for 3.15-rc2.
  Nothing major, just issues some people have reported.

  All of these have been in linux-next"

* tag 'usb-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  uas: fix deadlocky memory allocations
  uas: fix error handling during scsi_scan()
  uas: fix GFP_NOIO under spinlock
  uwb: adds missing error handling
  USB: cdc-acm: Remove Motorola/Telit H24 serial interfaces from ACM driver
  USB: ohci-jz4740: FEAT_POWER is a port feature, not a hub feature
  USB: ohci-jz4740: Fix uninitialized variable warning
  USB: EHCI: tegra: set txfill_tuning
  usb: ehci-platform: Return immediately from suspend if ehci_suspend fails
  usb: ehci-exynos: Return immediately from suspend if ehci_suspend fails
  USB: fix crash during hotplug of PCI USB controller card
  USB: cdc-acm: fix double usb_autopm_put_interface() in acm_port_activate()
  usb: usb-common: fix typo for usb_state_string
  USB: usb_wwan: fix handling of missing bulk endpoints
  USB: pl2303: add ids for Hewlett-Packard HP POS pole displays
  USB: cp210x: Add 8281 (Nanotec Plug & Drive)
  usb: option driver, add support for Telit UE910v2
  Revert "USB: serial: add usbid for dell wwan card to sierra.c"
  USB: serial: ftdi_sio: add id for Brainboxes serial cards

Merge misc fixes from Andrew Morton:
 "13 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  thp: close race between split and zap huge pages
  mm: fix new kernel-doc warning in filemap.c
  mm: fix CONFIG_DEBUG_VM_RB description
  mm: use paravirt friendly ops for NUMA hinting ptes
  mips: export flush_icache_range
  mm/hugetlb.c: add cond_resched_lock() in return_unused_surplus_pages()
  wait: explain the shadowing and type inconsistencies
  Shiraz has moved
  Documentation/vm/numa_memory_policy.txt: fix wrong document in numa_memory_policy.txt
  powerpc/mm: fix ".__node_distance" undefined
  kernel/watchdog.c:touch_softlockup_watchdog(): use raw_cpu_write()
  init/Kconfig: move the trusted keyring config option to general setup
  vmscan: reclaim_clean_pages_from_list() must use mod_zone_page_state()