- 13 May, 2014 20 commits
-
-
Dan Carpenter authored
commit b4c23305 upstream. We always put a NUL terminator one space past the end of the "vendor" buffer. Walter Harms also pointed out that this should just use kstrndup(). Fixes: 7d17c02a ('mtd: Add new SmartMedia/xD FTL') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
commit c69dbbf3 upstream. Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR" which is NULL and not a valid register. Fixes: 8bff82cb ('mtd: add nand support for w90p910 (v2)') Signed-off-by:
-
Mikulas Patocka authored
commit 6b0df682 upstream. The functions for data copying copyarea_foreward_8bpp and copyarea_backward_8bpp are buggy, they produce screen corruption. This patch fixes the functions and moves the logic to one function "copyarea_8bpp". For simplicity, the function only handles copying that is aligned on 8 pixes. If we copy an unaligned area, generic function cfb_copyarea is used. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Marek Vasut authored
commit a585f87c upstream. The scenario here is that someone calls enable_irq_wake() from somewhere in the code. This will result in the lockdep producing a backtrace as can be seen below. In my case, this problem is triggered when using the wl1271 (TI WlCore) driver found in drivers/net/wireless/ti/ . The problem cause is rather obvious from the backtrace, but let's outline the dependency. enable_irq_wake() grabs the IRQ buslock in irq_set_irq_wake(), which in turns calls mxs_gpio_set_wake_irq() . But mxs_gpio_set_wake_irq() calls enable_irq_wake() again on the one-level-higher IRQ , thus it tries to grab the IRQ buslock again in irq_set_irq_wake() . Because the spinlock in irq_set_irq_wake()->irq_get_desc_buslock()->__irq_get_desc_lock() is not marked as recursive, lockdep will spew the stuff below. We know we can safely re-enter the lock, so use IRQ_GC_INIT_NESTED_LOCK to fix the spew. ============================================= [ INFO: possible recursive locking detected ] 3.10.33-00012-gf06b763-dirty #61 Not tainted --------------------------------------------- kworker/0:1/18 is trying to acquire lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 but task is already holding lock: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&irq_desc_lock_class); lock(&irq_desc_lock_class); *** DEADLOCK *** May be due to missing lock nesting notation 3 locks held by kworker/0:1/18: #0: (events){.+.+.+}, at: [<c0036308>] process_one_work+0x134/0x4a4 #1: ((&fw_work->work)){+.+.+.}, at: [<c0036308>] process_one_work+0x134/0x4a4 #2: (&irq_desc_lock_class){-.-...}, at: [<c00685f0>] __irq_get_desc_lock+0x48/0x88 stack backtrace: CPU: 0 PID: 18 Comm: kworker/0:1 Not tainted 3.10.33-00012-gf06b763-dirty #61 Workqueue: events request_firmware_work_func [<c0013eb4>] (unwind_backtrace+0x0/0xf0) from [<c0011c74>] (show_stack+0x10/0x14) [<c0011c74>] (show_stack+0x10/0x14) from [<c005bb08>] (__lock_acquire+0x140c/0x1a64) [<c005bb08>] (__lock_acquire+0x140c/0x1a64) from [<c005c6a8>] (lock_acquire+0x9c/0x104) [<c005c6a8>] (lock_acquire+0x9c/0x104) from [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) [<c051d5a4>] (_raw_spin_lock_irqsave+0x44/0x58) from [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) [<c00685f0>] (__irq_get_desc_lock+0x48/0x88) from [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) [<c0068e78>] (irq_set_irq_wake+0x20/0xf4) from [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) [<c027260c>] (mxs_gpio_set_wake_irq+0x1c/0x24) from [<c0068cf4>] (set_irq_wake_real+0x30/0x44) [<c0068cf4>] (set_irq_wake_real+0x30/0x44) from [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) [<c0068ee4>] (irq_set_irq_wake+0x8c/0xf4) from [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) [<c0310748>] (wlcore_nvs_cb+0x10c/0x97c) from [<c02be5e8>] (request_firmware_work_func+0x38/0x58) [<c02be5e8>] (request_firmware_work_func+0x38/0x58) from [<c0036394>] (process_one_work+0x1c0/0x4a4) [<c0036394>] (process_one_work+0x1c0/0x4a4) from [<c0036a4c>] (worker_thread+0x138/0x394) [<c0036a4c>] (worker_thread+0x138/0x394) from [<c003cb74>] (kthread+0xa4/0xb0) [<c003cb74>] (kthread+0xa4/0xb0) from [<c000ee00>] (ret_from_fork+0x14/0x34) wlcore: loaded Signed-off-by:
Marek Vasut <marex@denx.de> Acked-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Larry Finger authored
commit 2610decd upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8192se. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Larry Finger authored
commit a53268be upstream. In commit f78bccd7 entitled "rtlwifi: rtl8192ce: Fix too long disable of IRQs", Olivier Langlois <olivier@trillion01.com> fixed a problem caused by an extra long disabling of interrupts. This patch makes the same fix for rtl8192cu. Signed-off-by:
-
Jeff Layton authored
commit 4991a628 upstream. A fl->fl_break_time of 0 has a special meaning to the lease break code that basically means "never break the lease". knfsd uses this to ensure that leases don't disappear out from under it. Unfortunately, the code in __break_lease can end up passing this value to wait_event_interruptible as a timeout, which prevents it from going to sleep at all. This causes __break_lease to spin in a tight loop and causes soft lockups. Fix this by ensuring that we pass a minimum value of 1 as a timeout instead. Cc: J. Bruce Fields <bfields@fieldses.org> Reported-by:
Terry Barnaby <terry1@beam.ltd.uk> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Dan Williams authored
commit 8a4aeec8 upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by:
Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Rafał Miłecki authored
commit 12cd43c6 upstream. Register B43_MMIO_PSM_PHY_HDR is 16 bit one, so accessing it with 32b functions isn't safe. On my machine it causes delayed (!) CPU exception: Disabling lock debugging due to kernel taint mce: [Hardware Error]: CPU 0: Machine Check Exception: 4 Bank 4: b200000000070f0f mce: [Hardware Error]: TSC 164083803dc mce: [Hardware Error]: PROCESSOR 2:20fc2 TIME 1396650505 SOCKET 0 APIC 0 microcode 0 mce: [Hardware Error]: Run the above through 'mcelog --ascii' mce: [Hardware Error]: Machine check: Processor context corrupt Kernel panic - not syncing: Fatal machine check on current CPU Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Acked-by:
-
Mikulas Patocka authored
commit 43751a1b upstream. This patch fixes the hardware cursor on mach64 when font width is not a multiple of 8 pixels. If you load such a font, the cursor is expanded to the next 8-byte boundary and a part of the next character after the cursor is not visible. For example, when you load a font with 12-pixel width, the cursor width is 16 pixels and when the cursor is displayed, 4 pixels of the next character are not visible. The reason is this: atyfb_cursor is called with proper parameters to load an image that is 12-pixel wide. However, the number is aligned on the next 8-pixel boundary on the line "unsigned int width = (cursor->image.width + 7) >> 3;" and the whole function acts as it is was loading a 16-pixel image. This patch fixes it so that the value written to the framebuffer is padded with 0xaaaa (the transparent pattern) when the image size it not a multiple of 8 pixels. The transparent pattern causes that the cursor will not interfere with the next character. Signed-off-by:
-
Mikulas Patocka authored
commit c29dd869 upstream. This patch fixes mach64 to use unaligned access to the font bitmap. This fixes unaligned access warning on sparc64 when 14x8 font is loaded. On x86(64), unaligned access is handled in hardware, so both functions le32_to_cpup and get_unaligned_le32 perform the same operation. On RISC machines, unaligned access is not handled in hardware, so we better use get_unaligned_le32 to avoid the unaligned trap and warning. Signed-off-by:
-
Mikulas Patocka authored
commit a772d473 upstream. When X11 is running and the user switches back to console, the card modifies the content of registers M_MACCESS and M_PITCH in periodic intervals. This patch fixes it by restoring the content of these registers before issuing any accelerator command. Signed-off-by:
-
Mikulas Patocka authored
commit 00a9d699 upstream. The function cfb_copyarea is buggy when the copy operation is not aligned on long boundary (4 bytes on 32-bit machines, 8 bytes on 64-bit machines). How to reproduce: - use x86-64 machine - use a framebuffer driver without acceleration (for example uvesafb) - set the framebuffer to 8-bit depth (for example fbset -a 1024x768-60 -depth 8) - load a font with character width that is not a multiple of 8 pixels note: the console-tools package cannot load a font that has width different from 8 pixels. You need to install the packages "kbd" and "console-terminus" and use the program "setfont" to set font width (for example: setfont Uni2-Terminus20x10) - move some text left and right on the bash command line and you get a screen corruption To expose more bugs, put this line to the end of uvesafb_init_info: info->flags |= FBINFO_HWACCEL_COPYAREA | FBINFO_READS_FAST; - Now framebuffer console will use cfb_copyarea for console scrolling. You get a screen corruption when console is scrolled. This patch is a rewrite of cfb_copyarea. It fixes the bugs, with this patch, console scrolling in 8-bit depth with a font width that is not a multiple of 8 pixels works fine. The cfb_copyarea code was very buggy and it looks like it was written and never tried with non-8-pixel font. Signed-off-by:
-
Ard Biesheuvel authored
commit 8ceee728 upstream. The GHASH setkey() function uses SSE registers but fails to call kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and then having to deal with the restriction that they cannot be called from interrupt context, move the setkey() implementation to the C domain. Note that setkey() does not use any particular SSE features and is not expected to become a performance bottleneck. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
H. Peter Anvin <hpa@linux.intel.com> Fixes: 0e1227d3 (crypto: ghash - Add PCLMULQDQ accelerated implementation) Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Tyler Stachecki authored
commit af61e27c upstream. On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which in turn calls pci_disable_device if the device is enabled prior to suspending. However, _scsih_suspend also calls pci_disable_device itself. Thus, in the event that the device is enabled prior to suspending, pci_disable_device will be called twice. This patch removes the duplicate call to pci_disable_device in _scsi_suspend as it is both unnecessary and results in a kernel oops. Signed-off-by:
Tyler Stachecki <tstache1@binghamton.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Rusty Russell authored
commit 1f74ef0f upstream. When adding or removing 100G from a balloon: BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367] We have a wait_event_interruptible(), but the condition is always true (more ballooning to do) so we don't ever sleep. We also have a wait_event() for the host to ack, but that is also always true as QEMU is synchronous for balloon operations. Reported-by:
Gopesh Kumar Chaudhary <gopchaud@in.ibm.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Huacai Chen authored
commit c14af233 upstream. The original MIPS hibernate code flushes cache and TLB entries in swsusp_arch_resume(). But they are removed in Commit 44eeab67 (MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross- CPU flush is surely unnecessary because all but the local CPU have already been disabled. But a local flush (at least the TLB flush) is needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is very easy to produce a kernel panic (kernel page fault, or unaligned access). The root cause is E1000E driver use vzalloc_node() to allocate pages, the stale TLB entries of the booting kernel will be misused by the resumed target kernel. Signed-off-by:
Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/6643/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
Matthew Daley authored
commit 2145e15e upstream. Do not leak kernel-only floppy_raw_cmd structure members to userspace. This includes the linked-list pointer and the pointer to the allocated DMA space. Signed-off-by:
Matthew Daley <mattd@bugfuzz.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Matthew Daley authored
commit ef87dbe7 upstream. Always clear out these floppy_raw_cmd struct members after copying the entire structure from userspace so that the in-kernel version is always valid and never left in an interdeterminate state. Signed-off-by:
-
Tomoki Sekiyama authored
commit 501fed45 upstream. When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest, hvc console is setup within a kthread. However, that will cause SEGV and the boot will fail when the driver is builtin to the kernel, because currently hvc_console_setup() is annotated with '__init'. This patch removes '__init' to boot the guest successfully with 'console=hvc0'. Signed-off-by:
Tomoki Sekiyama <tomoki.sekiyama@hds.com> Signed-off-by:
-
- 06 May, 2014 20 commits
-
-
Greg Kroah-Hartman authored
-
Aaron Sanders authored
commit b16c02fb upstream. Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays: LD960: 03f0:0B39 LCM220: 03f0:3139 LCM960: 03f0:3239 [ Johan: fix indentation and sort PIDs numerically ] Signed-off-by:
Aaron Sanders <aaron.sanders@hp.com> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Theodore Ts'o authored
commit 6e6358fc upstream. We haven't taken i_mutex yet, so we need to use i_size_read(). Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
alex chen authored
commit f7cf4f5b upstream. Do not put bh when buffer_uptodate failed in ocfs2_write_block and ocfs2_write_super_or_backup, because it will put bh in b_end_io. Otherwise it will hit a warning "VFS: brelse: Trying to free free buffer". Signed-off-by:
Alex Chen <alex.chen@huawei.com> Reviewed-by:
Joseph Qi <joseph.qi@huawei.com> Reviewed-by:
Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Acked-by:
Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Junxiao Bi authored
commit ded2cf71 upstream. There is a race window in dlm_do_recovery() between dlm_remaster_locks() and dlm_reset_recovery() when the recovery master nearly finish the recovery process for a dead node. After the master sends FINALIZE_RECO message in dlm_remaster_locks(), another node may become the recovery master for another dead node, and then send the BEGIN_RECO message to all the nodes included the old master, in the handler of this message dlm_begin_reco_handler() of old master, dlm->reco.dead_node and dlm->reco.new_master will be set to the second dead node and the new master, then in dlm_reset_recovery(), these two variables will be reset to default value. This will cause new recovery master can not finish the recovery process and hung, at last the whole cluster will hung for recovery. old recovery master: new recovery master: dlm_remaster_locks() become recovery master for another dead node. dlm_send_begin_reco_message() dlm_begin_reco_handler() { if (dlm->reco.state & DLM_RECO_STATE_FINALIZE) { return -EAGAIN; } dlm_set_reco_master(dlm, br->node_idx); dlm_set_reco_dead_node(dlm, br->dead_node); } dlm_reset_recovery() { dlm_set_reco_dead_node(dlm, O2NM_INVALID_NODE_NUM); dlm_set_reco_master(dlm, O2NM_INVALID_NODE_NUM); } will hang in dlm_remaster_locks() for request dlm locks info Before send FINALIZE_RECO message, recovery master should set DLM_RECO_STATE_FINALIZE for itself and clear it after the recovery done, this can break the race windows as the BEGIN_RECO messages will not be handled before DLM_RECO_STATE_FINALIZE flag is cleared. A similar race may happen between new recovery master and normal node which is in dlm_finalize_reco_handler(), also fix it. Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Wengang Wang <wen.gang.wang@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by:
-
Junxiao Bi authored
commit 34aa8dac upstream. This issue was introduced by commit 800deef3 ("ocfs2: use list_for_each_entry where benefical") in 2007 where it replaced list_for_each with list_for_each_entry. The variable "lock" will point to invalid data if "tmpq" list is empty and a panic will be triggered due to this. Sunil advised reverting it back, but the old version was also not right. At the end of the outer for loop, that list_for_each_entry will also set "lock" to an invalid data, then in the next loop, if the "tmpq" list is empty, "lock" will be an stale invalid data and cause the panic. So reverting the list_for_each back and reset "lock" to NULL to fix this issue. Another concern is that this seemes can not happen because the "tmpq" list should not be empty. Let me describe how. old lock resource owner(node 1): migratation target(node 2): image there's lockres with a EX lock from node 2 in granted list, a NR lock from node x with convert_type EX in converting list. dlm_empty_lockres() { dlm_pick_migration_target() { pick node 2 as target as its lock is the first one in granted list. } dlm_migrate_lockres() { dlm_mark_lockres_migrating() { res->state |= DLM_LOCK_RES_BLOCK_DIRTY; wait_event(dlm->ast_wq, !dlm_lockres_is_dirty(dlm, res)); //after the above code, we can not dirty lockres any more, // so dlm_thread shuffle list will not run downconvert lock from EX to NR upconvert lock from NR to EX <<< migration may schedule out here, then <<< node 2 send down convert request to convert type from EX to <<< NR, then send up convert request to convert type from NR to <<< EX, at this time, lockres granted list is empty, and two locks <<< in the converting list, node x up convert lock followed by <<< node 2 up convert lock. // will set lockres RES_MIGRATING flag, the following // lock/unlock can not run dlm_lockres_release_ast(dlm, res); } dlm_send_one_lockres() dlm_process_recovery_data() for (i=0; i<mres->num_locks; i++) if (ml->node == dlm->node_num) for (j = DLM_GRANTED_LIST; j <= DLM_BLOCKED_LIST; j++) { list_for_each_entry(lock, tmpq, list) if (lock) break; <<< lock is invalid as grant list is empty. } if (lock->ml.node != ml->node) BUG() >>> crash here } I see the above locks status from a vmcore of our internal bug. Signed-off-by:
-
Liu Hua authored
commit 80df2847 upstream. As sysctl_hung_task_timeout_sec is unsigned long, when this value is larger then LONG_MAX/HZ, the function schedule_timeout_interruptible in watchdog will return immediately without sleep and with print : schedule_timeout: wrong timeout value ffffffffffffff83 and then the funtion watchdog will call schedule_timeout_interruptible again and again. The screen will be filled with "schedule_timeout: wrong timeout value ffffffffffffff83" This patch does some check and correction in sysctl, to let the function schedule_timeout_interruptible allways get the valid parameter. Signed-off-by:
Liu Hua <sdu.liu@huawei.com> Tested-by:
Satoru Takeuchi <satoru.takeuchi@gmail.com> Signed-off-by:
-
Mizuma, Masayoshi authored
commit 55f67141 upstream. When I decrease the value of nr_hugepage in procfs a lot, softlockup happens. It is because there is no chance of context switch during this process. On the other hand, when I allocate a large number of hugepages, there is some chance of context switch. Hence softlockup doesn't happen during this process. So it's necessary to add the context switch in the freeing process as same as allocating process to avoid softlockup. When I freed 12 TB hugapages with kernel-2.6.32-358.el6, the freeing process occupied a CPU over 150 seconds and following softlockup message appeared twice or more. $ echo 6000000 > /proc/sys/vm/nr_hugepages $ cat /proc/sys/vm/nr_hugepages 6000000 $ grep ^Huge /proc/meminfo HugePages_Total: 6000000 HugePages_Free: 6000000 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB $ echo 0 > /proc/sys/vm/nr_hugepages BUG: soft lockup - CPU#16 stuck for 67s! [sh:12883] ... Pid: 12883, comm: sh Not tainted 2.6.32-358.el6.x86_64 #1 Call Trace: free_pool_huge_page+0xb8/0xd0 set_max_huge_pages+0x128/0x190 hugetlb_sysctl_handler_common+0x113/0x140 hugetlb_sysctl_handler+0x1e/0x20 proc_sys_call_handler+0x97/0xd0 proc_sys_write+0x14/0x20 vfs_write+0xb8/0x1a0 sys_write+0x51/0x90 __audit_syscall_exit+0x265/0x290 system_call_fastpath+0x16/0x1b I have not confirmed this problem with upstream kernels because I am not able to prepare the machine equipped with 12TB memory now. However I confirmed that the amount of decreasing hugepages was directly proportional to the amount of required time. I measured required times on a smaller machine. It showed 130-145 hugepages decreased in a millisecond. Amount of decreasing Required time Decreasing rate hugepages (msec) (pages/msec) ------------------------------------------------------------ 10,000 pages == 20GB 70 - 74 135-142 30,000 pages == 60GB 208 - 229 131-144 It means decrement of 6TB hugepages will trigger softlockup with the default threshold 20sec, in this decreasing rate. Signed-off-by:
Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by:
-
Matt Fleming authored
commit a0c32761 upstream. Kees reported the following error: arch/sh/kernel/dumpstack.c: In function 'print_trace_address': arch/sh/kernel/dumpstack.c:118:2: error: format not a string literal and no format arguments [-Werror=format-security] Use the "%s" format so that it's impossible to interpret 'data' as a format string. Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Reported-by:
Kees Cook <keescook@chromium.org> Acked-by:
-
Alan Stern authored
commit 6aec044c upstream. When a driver doesn't have pre_reset, post_reset, or reset_resume methods, the USB core unbinds that driver when its device undergoes a reset or a reset-resume, and then rebinds it afterward. The existing straightforward implementation can lead to problems, because each interface gets unbound and rebound before the next interface is handled. If a driver claims additional interfaces, the claim may fail because the old binding instance may still own the additional interface when the new instance tries to claim it. This patch fixes the problem by first unbinding all the interfaces that are marked (i.e., their needs_binding flag is set) and then rebinding all of them. The patch also makes the helper functions in driver.c a little more uniform and adjusts some out-of-date comments. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by:
"Poulain, Loic" <loic.poulain@intel.com> Signed-off-by:
-
Paul Gortmaker authored
commit f76a1cbe upstream. Commit 3e6c6f63 ("Delay creation of khcvd thread") moved the call of hvc_init from being a device_initcall into hvc_alloc, and used a non-null hvc_driver as indication of whether hvc_init had already been called. The problem with this is that hvc_driver is only assigned a value at the bottom of hvc_init, and so there is a window where multiple hvc_alloc calls can be in progress at the same time and hence try and call hvc_init multiple times. Previously the use of device_init guaranteed that hvc_init was only called once. This manifests itself as sporadic instances of two hvc_init calls racing each other, and with the loser of the race getting -EBUSY from tty_register_driver() and hence that virtual console fails: Couldn't register hvc console driver virtio-ports vport0p1: error -16 allocating hvc for port Here we add an atomic_t to guarantee we'll never run hvc_init twice. Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 3e6c6f63 ("Delay creation of khcvd thread") Reported-by:
Jim Somerville <Jim.Somerville@windriver.com> Tested-by:
Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by:
-
Huang Rui authored
commit 06f9b6e5 upstream. Around DWC USB3 2.30a release another bit has been added to the Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield. Because of that, what used to be 8 bits long, has become 9 bits long. Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits not 8 bits. And the following reserved field uses [31:25] bits not [31:24] bits, and it has 7 bits. So in dwc3_event_devt, the bit mask should be: event_info [24:16] 9 bits reserved31_25 [31:25] 7 bits This patch makes sure that newer core releases will work fine with Linux and that we will decode the event information properly on new core releases. [ balbi@ti.com : improve commit log a bit ] Signed-off-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
David Cohen authored
commit 01bb59eb upstream. When CONFIG_PCI and CONFIG_PM are not selected, xhci.c gets this warning: drivers/usb/host/xhci.c:409:13: warning: ‘xhci_msix_sync_irqs’ defined but not used [-Wunused-function] Instead of creating nested #ifdefs, this patch fixes it by defining the xHCI PCI stubs as inline. This warning has been in since 3.2 kernel and was caused by commit 421aa841 "usb/xhci: hide MSI code behind PCI bars", but wasn't noticed until 3.13 when a configuration with these options was tried Signed-off-by:
David Cohen <david.a.cohen@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Igor Gnatenko authored
commit 6db249eb upstream. After suspend another Renesas PCI-X USB 3.0 card doesn't work. [root@fedora-20 ~]# lspci -vmnnd 1912: Device: 03:00.0 Class: USB controller [0c03] Vendor: Renesas Technology Corp. [1912] Device: uPD720202 USB 3.0 Host Controller [0015] SVendor: Renesas Technology Corp. [1912] SDevice: uPD720202 USB 3.0 Host Controller [0015] Rev: 02 ProgIf: 30 This patch should be applied to stable kernel 3.14 that contain the commit 1aa9578c "xhci: Fix resume issues on Renesas chips in Samsung laptops" Reported-and-tested-by:
Anatoly Kharchenko <rfr-bugs@yandex.ru> Reference: http://redmine.russianfedora.pro/issues/1315Signed-off-by:
Igor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by:
-
supriya karanth authored
commit bb3a2ef2 upstream. The TXMAXP register is not set correctly for full speed bulk case when the can_bulk_split() is used. Without this PIO transfers will not take place correctly The "mult" factor needs to be updated correctly for the can_bulk_split() case The AUTOSET bit in the TXCSR is not being set if the "mult" factor is greater than 0 for the High Bandwidth ISO case. But the "mult" factor is also greater than 0 in case of Full speed bulk transfers with the packet splitting in TXMAXP register Without the AUTOSET the DMA transfers will not progress in mode1 [ balbi@ti.com : add braces to both branches ] Signed-off-by:
supriya karanth <supriya.karanth@stericsson.com> Signed-off-by:
Praveena NADAHALLY <praveen.nadahally@stericsson.com> Acked-by:
-
Jeff Mahoney authored
commit 01d88857 upstream. jdm-20004 reiserfs_delete_xattrs: Couldn't delete all xattrs (-2) The -ENOENT is due to readdir calling dir_emit on the same entry twice. If the dir_emit callback sleeps and the tree is changed underneath us, we won't be able to trust deh_offset(deh) anymore. We need to save next_pos before we might sleep so we can find the next entry. Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Andy Grover authored
commit 2c42be2d upstream. ft_del_tpg checks tpg->tport is set before unlinking the tpg from the tport when the tpg is being removed. Set this pointer in ft_tport_create, or the unlinking won't happen in ft_del_tpg and tport->tpg will reference a deleted object. This patch sets tpg->tport in ft_tport_create, because that's what ft_del_tpg checks, and is the only way to get back to the tport to clear tport->tpg. The bug was occuring when: - lport created, tport (our per-lport, per-provider context) is allocated. tport->tpg = NULL - tpg created - a PRLI is received. ft_tport_create is called, tpg is found and tport->tpg is set - tpg removed. ft_tpg is freed in ft_del_tpg. Since tpg->tport was not set, tport->tpg is not cleared and points at freed memory - Future calls to ft_tport_create return tport via first conditional, instead of searching for new tpg by calling ft_lport_find_tpg. tport->tpg is still invalid, and will access freed memory. see https://bugzilla.redhat.com/show_bug.cgi?id=1071340Signed-off-by:
Andy Grover <agrover@redhat.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit d444edc6 upstream. This patch fixes a long-standing bug in iscsit_build_conn_drop_async_message() where during ERL=2 connection recovery, a bogus conn_p pointer could end up being used to send the ISCSI_OP_ASYNC_EVENT + DROPPING_CONNECTION notifying the initiator that cmd->logout_cid has failed. The bug was manifesting itself as an OOPs in iscsit_allocate_cmd() with a bogus conn_p pointer in iscsit_build_conn_drop_async_message(). Reported-by:
Arshad Hussain <arshad.hussain@calsoftinc.com> Reported-by:
santosh kulkarni <santosh.kulkarni@calsoftinc.com> Signed-off-by:
-
Dan Carpenter authored
commit e2c70425 upstream. The original code always set the upper 32 bits to zero because it was doing a shift of the wrong variable. Fixes: 1a4f550a ('[SCSI] arcmsr: 1.20.00.15: add SATA RAID plus other fixes') Signed-off-by:
-
Mike Marciniszyn authored
commit b0768080 upstream. The code was incorrectly using sg_dma_address() and sg_dma_len() instead of ib_sg_dma_address() and ib_sg_dma_len(). This prevents srpt from functioning with the Intel HCA and indeed will corrupt memory badly. Cc: Bart Van Assche <bvanassche@acm.org> Reviewed-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Tested-by:
Vinod Kumar <vinod.kumar@intel.com> Signed-off-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
-
