- 30 Mar, 2021 2 commits
-
-
Caleb Connolly authored
Add the first and third qupv3 nodes used to hook up peripherals on some devices, as well as the iommus properties for all of them. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Link: https://lore.kernel.org/r/20210321174522.123036-2-caleb@connolly.techSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Jonathan Marek authored
Apply these fixes to the newly added sm8250 display ndoes - Remove "notused" interconnect (which apparently was blindly copied from my old patches) - Use dispcc node example from dt-bindings, removing clocks which aren't documented or used by the driver and fixing the region size. Fixes: 7c1dffd4 ("arm64: dts: qcom: sm8250.dtsi: add display system nodes") Signed-off-by:
Jonathan Marek <jonathan@marek.ca> [DB: compatibility changes split into separate patch] Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210329120051.3401567-2-dmitry.baryshkov@linaro.orgSigned-off-by:
-
- 18 Mar, 2021 4 commits
-
-
Dmitry Baryshkov authored
On the GENI SPI controller is is not very efficient if the chip select line is controlled by the QUP itself (see 37dd4b77 ("arm64: dts: qcom: sc7180: Provide pinconf for SPI to use GPIO for CS") for the details). Configure SPI0 CS pin as a GPIO. Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210210133458.1201066-5-dmitry.baryshkov@linaro.orgSigned-off-by:
-
Dmitry Baryshkov authored
GENI SPI controller shows several issues if it manages the CS on its own (see 37dd4b77 ("arm64: dts: qcom: sc7180: Provide pinconf for SPI to use GPIO for CS")) for the details. Provide pinctrl entries for SPI controllers using the same CS pin but in GPIO mode. Signed-off-by:
-
Dmitry Baryshkov authored
Split "default" device tree nodes into common "data-clk" nodes and "cs" nodes which might differ from board to board depending on how the slave chips are wired. Reviewed-by:
-
Dmitry Baryshkov authored
As discussed on linux-arm-msm list, start splitting sm8250 pinctrl settings into generic and board-specific parts. The first part to receive such treatment is the spi, so split spi pinconf to the board device tree. Reviewed-by:
-
- 16 Mar, 2021 3 commits
-
-
Robert Foss authored
Enable camss & ov8856 DT nodes. Signed-off-by:
Robert Foss <robert.foss@linaro.org> Reviewed-by:
Andrey Konovalov <andrey.konovalov@linaro.org> Link: https://lore.kernel.org/r/20210316171931.812748-23-robert.foss@linaro.orgSigned-off-by:
-
Robert Foss authored
Add regulator to camss device tree node. Signed-off-by:
-
Robert Foss authored
Add the camss dt node for sdm845. Signed-off-by:
-
- 12 Mar, 2021 31 commits
-
-
Bjorn Andersson authored
The PM8150 comes with everything the RTC needs, so let's just leave it enabled instead of having to explicitly enable it for all boards. In effect this patch enables the RTC on the SM8150 MTP and the SM8250 HDK. Acked-by:
-
Vinod Koul authored
SM8350-MTP features PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B. PMICs Add the dtsi for these PMICs to MTP. Signed-off-by:
Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20210312052737.3558801-9-vkoul@kernel.orgSigned-off-by:
-
Vinod Koul authored
Add base DTS file for PMR735B along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add base DTS file for PMR735A along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add base DTS file for PM8350C along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add base DTS file for PM8350B along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add base DTS file for PM8350 along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add base DTS file for PMK8350 along with GPIO node Signed-off-by:
-
Vinod Koul authored
Add SPMI node found in SM8350 SoC Signed-off-by:
-
Srinivas Kandagatla authored
WSA881x powerdown pin is connected to GPIO1 not gpio2, so correct this. This was working so far due to a shift bug in gpio driver, however once that is fixed this will stop working, so fix this! Fixes: 89a32a4e ("arm64: dts: qcom: db845c: add analog audio support") Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20210309102025.28405-1-srinivas.kandagatla@linaro.orgSigned-off-by:
-
Bjorn Andersson authored
Document the SM8350 Hardware Development Kit (HDK). Reviewed-by:
-
Stephen Boyd authored
This moved from being trogdor specific to being part of the general sc7180.dtsi SoC file in commit 681a607a ("arm64: dts: qcom: sc7180: Add DisplayPort HPD pin dt node"). Then we dropped the pinconf from the general sc7180.dtsi file in commit 8d079bf2 ("arm64: dts: qcom: sc7180: Drop pinconf on dp_hot_plug_det") and added it back to the trogdor dts file in commit f772081f ("arm64: dts: qcom: sc7180: Add "dp_hot_plug_det" pinconf for trogdor"). As part of this we managed to forget to drop the old copy in the trogdor dts. Let's do it now. Signed-off-by:
Stephen Boyd <swboyd@chromium.org> [dianders: updated desc] Signed-off-by:
-
Shawn Guo authored
The last cell of 'gpio-ranges' should be number of GPIO pins, and in case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather than msm_pinctrl_soc_data.ngpio - 1. This fixes the problem that when the last GPIO pin in the range is configured with the following call sequence, it always fails with -EPROBE_DEFER. pinctrl_gpio_set_config() pinctrl_get_device_gpio_range() pinctrl_match_gpio_range() Fixes: b7e8f433 ("arm64: dts: qcom: Add basic devicetree support for SM8350 SoC") Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by:Shawn Guo <shawn.guo@linaro.org> Link: https://lore.kernel.org/r/20210303033106.549-5-shawn.guo@linaro.orgSigned-off-by:
-
Shawn Guo authored
The last cell of 'gpio-ranges' should be number of GPIO pins, and in case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather than msm_pinctrl_soc_data.ngpio - 1. This fixes the problem that when the last GPIO pin in the range is configured with the following call sequence, it always fails with -EPROBE_DEFER. pinctrl_gpio_set_config() pinctrl_get_device_gpio_range() pinctrl_match_gpio_range() Fixes: 16951b49 ("arm64: dts: qcom: sm8250: Add TLMM pinctrl node") Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: -
Shawn Guo authored
The last cell of 'gpio-ranges' should be number of GPIO pins, and in case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather than msm_pinctrl_soc_data.ngpio - 1. This fixes the problem that when the last GPIO pin in the range is configured with the following call sequence, it always fails with -EPROBE_DEFER. pinctrl_gpio_set_config() pinctrl_get_device_gpio_range() pinctrl_match_gpio_range() Fixes: e13c6d14 ("arm64: dts: qcom: sm8150: Add base dts file") Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: -
Shawn Guo authored
The last cell of 'gpio-ranges' should be number of GPIO pins, and in case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather than msm_pinctrl_soc_data.ngpio - 1. This fixes the problem that when the last GPIO pin in the range is configured with the following call sequence, it always fails with -EPROBE_DEFER. pinctrl_gpio_set_config() pinctrl_get_device_gpio_range() pinctrl_match_gpio_range() Fixes: bc2c8062 ("arm64: dts: qcom: sdm845: Add gpio-ranges to TLMM node") Cc: Evan Green <evgreen@chromium.org> Signed-off-by: -
Rajendra Nayak authored
Add the DT node for the rpmhpd power controller on SC7280 SoCs. Signed-off-by:
Rajendra Nayak <rnayak@codeaurora.org> Reviewed-by:
-
Maulik Shah authored
Add cpuidle states for little and big cpus. The latency values are preliminary placeholders and will be updated once testing provides the real numbers. Signed-off-by:
Maulik Shah <mkshah@codeaurora.org> Signed-off-by:
-
satya priya authored
Add SPMI PMIC arbiter device to communicate with PMICs attached to SPMI bus. Signed-off-by:
satya priya <skakit@codeaurora.org> Signed-off-by:
-
Sai Prakash Ranjan authored
Add APSS (Application Processor Subsystem) watchdog DT node for SC7280 SoC. Signed-off-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Signed-off-by:
-
Maulik Shah authored
Add fw reserved memory area for CPUCP (CPUSS control processor) and AOP (Always ON processor) Signed-off-by:
-
Sai Prakash Ranjan authored
Adding device node for APPS SMMU available on SC7280 chipset. This is shared among the multiple client devices such as display, video, usb, mmc and others. Signed-off-by:
-
Rajendra Nayak authored
Add rpmhcc clock controller node for SC7280. Also add references to rpmhcc clocks in gcc. Signed-off-by:
Taniya Das <tdas@codeaurora.org> Signed-off-by:
-
Maulik Shah authored
Add PDC interrupt controller along with apps RSC device. Also add reserved memory for command_db. Signed-off-by:
-
Rajendra Nayak authored
Add initial device tree support for the sc7280 SoC and the IDP boards based on this SoC Signed-off-by:
-
Rajendra Nayak authored
Document the sc7280 SoC and the IDP board bindings Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/1615461961-17716-2-git-send-email-rnayak@codeaurora.orgSigned-off-by:
-
Bjorn Andersson authored
Add initial DTS for the Snapdragon 888 Mobile Hardware Development Kit, aka SM8350 HDK. This initial version describes debug UART, UFS storage, the three USB connectors and remoteprocs. Reviewed-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by:
-
Vinod Koul authored
Document the various sony boards for apq8094. These are used in various sony dts files but not documented Signed-off-by:
-
Vinod Koul authored
We expect bootloader to full memory details but passing empty values gives warning, so add a default value arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 0, 0, 0]]} Signed-off-by: -
Vinod Koul authored
Document the ipq6018-cp01 board. It was missing leading to warning: arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dt.yaml: /: compatible: 'oneOf' conditional failed, one must be fixed: ['qcom,ipq6018-cp01', 'qcom,ipq6018'] is too short ['qcom,ipq6018-cp01', 'qcom,ipq6018'] is too long Additional items are not allowed ('qcom,ipq6018' was unexpected) Signed-off-by: -
Vinod Koul authored
We expect bootloader to full memory details but passing empty values gives warning, so add a default value arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 0, 0, 0]]} Signed-off-by:
-
