- 19 Apr, 2023 3 commits
-
-
Ondrej Kozina authored
Locking range start and locking range length attributes may be require to satisfy restrictions exposed by OPAL2 geometry feature reporting. Geometry reporting feature is described in TCG OPAL SSC, section 3.1.1.4 (ALIGN, LogicalBlockSize, AlignmentGranularity and LowestAlignedLBA). 4.3.5.2.1.1 RangeStart Behavior: [ StartAlignment = (RangeStart modulo AlignmentGranularity) - LowestAlignedLBA ] When processing a Set method or CreateRow method on the Locking table for a non-Global Range row, if: a) the AlignmentRequired (ALIGN above) column in the LockingInfo table is TRUE; b) RangeStart is non-zero; and c) StartAlignment is non-zero, then the method SHALL fail and return an error status code INVALID_PARAMETER. 4.3.5.2.1.2 RangeLength Behavior: If RangeStart is zero, then [ LengthAlignment = (RangeLength modulo AlignmentGranularity) - LowestAlignedLBA ] If RangeStart is non-zero, then [ LengthAlignment = (RangeLength modulo AlignmentGranularity) ] When processing a Set method or CreateRow method on the Locking table for a non-Global Range row, if: a) the AlignmentRequired (ALIGN above) column in the LockingInfo table is TRUE; b) RangeLength is non-zero; and c) LengthAlignment is non-zero, then the method SHALL fail and return an error status code INVALID_PARAMETER In userspace we stuck to logical block size reported by general block device (via sysfs or ioctl), but we can not read 'AlignmentGranularity' or 'LowestAlignedLBA' anywhere else and we need to get those values from sed-opal interface otherwise we will not be able to report or avoid locking range setup INVALID_PARAMETER errors above. Signed-off-by:
Ondrej Kozina <okozina@redhat.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Christian Brauner <brauner@kernel.org> Tested-by:
Milan Broz <gmazyland@gmail.com> Link: https://lore.kernel.org/r/20230411090931.9193-2-okozina@redhat.comSigned-off-by:
Jens Axboe <axboe@kernel.dk>
-
Chaitanya Kulkarni authored
Make sure to check device queue mode in the null_validate_conf() and return error for NULL_Q_RQ as we don't allow legacy I/O path, without this patch we get OOPs when queue mode is set to 1 from configfs, following are repro steps :- modprobe null_blk nr_devices=0 mkdir config/nullb/nullb0 echo 1 > config/nullb/nullb0/memory_backed echo 4096 > config/nullb/nullb0/blocksize echo 20480 > config/nullb/nullb0/size echo 1 > config/nullb/nullb0/queue_mode echo 1 > config/nullb/nullb0/power Entering kdb (current=0xffff88810acdd080, pid 2372) on processor 42 Oops: (null) due to oops @ 0xffffffffc041c329 CPU: 42 PID: 2372 Comm: sh Tainted: G O N 6.3.0-rc5lblk+ #5 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014 RIP: 0010:null_add_dev.part.0+0xd9/0x720 [null_blk] Code: 01 00 00 85 d2 0f 85 a1 03 00 00 48 83 bb 08 01 00 00 00 0f 85 f7 03 00 00 80 bb 62 01 00 00 00 48 8b 75 20 0f 85 6d 02 00 00 <48> 89 6e 60 48 8b 75 20 bf 06 00 00 00 e8 f5 37 2c c1 48 8b 75 20 RSP: 0018:ffffc900052cbde0 EFLAGS: 00010246 RAX: 0000000000000001 RBX: ffff88811084d800 RCX: 0000000000000001 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888100042e00 RBP: ffff8881053d8200 R08: ffffc900052cbd68 R09: ffff888105db2000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000002 R13: ffff888104765200 R14: ffff88810eec1748 R15: ffff88810eec1740 FS: 00007fd445fd1740(0000) GS:ffff8897dfc80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000060 CR3: 0000000166a00000 CR4: 0000000000350ee0 DR0: ffffffff8437a488 DR1: ffffffff8437a489 DR2: ffffffff8437a48a DR3: ffffffff8437a48b DR6: 00000000ffff0ff0 DR7: 0000000000000400 Call Trace: <TASK> nullb_device_power_store+0xd1/0x120 [null_blk] configfs_write_iter+0xb4/0x120 vfs_write+0x2ba/0x3c0 ksys_write+0x5f/0xe0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x7fd4460c57a7 Code: 0d 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 RSP: 002b:00007ffd3792a4a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007fd4460c57a7 RDX: 0000000000000002 RSI: 000055b43c02e4c0 RDI: 0000000000000001 RBP: 000055b43c02e4c0 R08: 000000000000000a R09: 00007fd44615b4e0 R10: 00007fd44615b3e0 R11: 0000000000000246 R12: 0000000000000002 R13: 00007fd446198520 R14: 0000000000000002 R15: 00007fd446198700 </TASK> Signed-off-by:
Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by:
Damien Le Moal <dlemoal@kernel.org> Reviewed-by:
Ming Lei <ming.lei@redhat.com> Reviewed-by:
Nitesh Shetty <nj.shetty@samsung.com> Link: https://lore.kernel.org/r/20230416220339.43845-1-kch@nvidia.comSigned-off-by:
-
Ming Lei authored
All ublk commands(control, IO) should have taken ioctl command encoding from the beginning, because ioctl command encoding defines each code uniquely, so driver can figure out wrong command sent from userspace easily; 2) it might help security subsystem for audit uring cmd[1]. Unfortunately we didn't do that way, and it could be one lesson for ublk driver. So switch to ioctl command encoding now, we still support commands encoded in old way, but they become legacy definition. Any new command should take ioctl encoding. See ublksrv code for switching to ioctl command encoding in [2]. [1] https://lore.kernel.org/io-uring/CAHC9VhSVzujW9LOj5Km80AjU0EfAuukoLrxO6BEfnXeK_s6bAg@mail.gmail.com/ [2] https://github.com/ming1/ubdsrv/commits/ioctl_cmd_encoding Cc: Christoph Hellwig <hch@infradead.org> Cc: Ken Kurematsu <k.kurematsu@nskint.co.jp> Signed-off-by:
-
- 16 Apr, 2023 5 commits
-
-
Christoph Hellwig authored
Commit b12e5c6c accidentally changes blk_kick_flush to do a head insert into the requeue list, fix this up. Fixes: b12e5c6c ("blk-mq: pass a flags argument to blk_mq_add_to_requeue_list") Signed-off-by:
-
Colin Ian King authored
When the weighted sum is zero the calculation of limit causes a division by zero error. Fix this by continuing to the next level. This was discovered by running as root: stress-ng --ioprio 0 Fixes divison by error oops: [ 521.450556] divide error: 0000 [#1] SMP NOPTI [ 521.450766] CPU: 2 PID: 2684464 Comm: stress-ng-iopri Not tainted 6.2.1-1280.native #1 [ 521.451117] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014 [ 521.451627] RIP: 0010:bfqq_request_over_limit+0x207/0x400 [ 521.451875] Code: 01 48 8d 0c c8 74 0b 48 8b 82 98 00 00 00 48 8d 0c c8 8b 85 34 ff ff ff 48 89 ca 41 0f af 41 50 48 d1 ea 48 98 48 01 d0 31 d2 <48> f7 f1 41 39 41 48 89 85 34 ff ff ff 0f 8c 7b 01 00 00 49 8b 44 [ 521.452699] RSP: 0018:ffffb1af84eb3948 EFLAGS: 00010046 [ 521.452938] RAX: 000000000000003c RBX: 0000000000000000 RCX: 0000000000000000 [ 521.453262] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffb1af84eb3978 [ 521.453584] RBP: ffffb1af84eb3a30 R08: 0000000000000001 R09: ffff8f88ab8a4ba0 [ 521.453905] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8f88ab8a4b18 [ 521.454224] R13: ffff8f8699093000 R14: 0000000000000001 R15: ffffb1af84eb3970 [ 521.454549] FS: 00005640b6b0b580(0000) GS:ffff8f88b3880000(0000) knlGS:0000000000000000 [ 521.454912] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 521.455170] CR2: 00007ffcbcae4e38 CR3: 00000002e46de001 CR4: 0000000000770ee0 [ 521.455491] PKRU: 55555554 [ 521.455619] Call Trace: [ 521.455736] <TASK> [ 521.455837] ? bfq_request_merge+0x3a/0xc0 [ 521.456027] ? elv_merge+0x115/0x140 [ 521.456191] bfq_limit_depth+0xc8/0x240 [ 521.456366] __blk_mq_alloc_requests+0x21a/0x2c0 [ 521.456577] blk_mq_submit_bio+0x23c/0x6c0 [ 521.456766] __submit_bio+0xb8/0x140 [ 521.457236] submit_bio_noacct_nocheck+0x212/0x300 [ 521.457748] submit_bio_noacct+0x1a6/0x580 [ 521.458220] submit_bio+0x43/0x80 [ 521.458660] ext4_io_submit+0x23/0x80 [ 521.459116] ext4_do_writepages+0x40a/0xd00 [ 521.459596] ext4_writepages+0x65/0x100 [ 521.460050] do_writepages+0xb7/0x1c0 [ 521.460492] __filemap_fdatawrite_range+0xa6/0x100 [ 521.460979] file_write_and_wait_range+0xbf/0x140 [ 521.461452] ext4_sync_file+0x105/0x340 [ 521.461882] __x64_sys_fsync+0x67/0x100 [ 521.462305] ? syscall_exit_to_user_mode+0x2c/0x1c0 [ 521.462768] do_syscall_64+0x3b/0xc0 [ 521.463165] entry_SYSCALL_64_after_hwframe+0x5a/0xc4 [ 521.463621] RIP: 0033:0x5640b6c56590 [ 521.464006] Code: 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 80 3d 71 70 0e 00 00 74 17 b8 4a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 48 c3 0f 1f 80 00 00 00 00 48 83 ec 18 89 7c Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20230413133009.1605335-1-colin.i.king@gmail.comSigned-off-by:
-
Akinobu Mita authored
This fixes a build error when CONFIG_FAULT_INJECTION_CONFIGFS=y and CONFIG_CONFIGFS_FS=m. Since the fault-injection library cannot built as a module, avoid building configfs as a module. Fixes: 4668c7a2 ("fault-inject: allow configuration via configfs") Reported-by:
kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/oe-kbuild-all/202304150025.K0hczLR4-lkp@intel.com/Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Jens Axboe authored
We have a long chain of memory dereferencing just to whether or not this disk has a special submit_bio helper. As that's not necessarily the common case, add a bd_has_submit_bio state in the bdev to avoid traversing this memory dependency chain if we don't need to. Signed-off-by: -
Jens Axboe authored
This moves struct device out-of-line as it's just used at open/close time, so we can keep some of the commonly used fields closer together. On a standard setup, it also reduces the size from 864 bytes to 848 bytes. Yes, struct device is a pig... Reviewed-by:
-
- 14 Apr, 2023 17 commits
-
-
Jens Axboe authored
Merge branch 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-6.4/block Pull MD updates from Song: "- md/bitmap: Optimal last page size, by Jon Derrick - Various raid10 fixes, by Yu Kuai and Li Nan - md: add error_handlers for raid0 and linear, by Mariusz Tkaczyk" * 'md-next' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md: md/raid5: remove unused working_disks variable md/raid10: don't call bio_start_io_acct twice for bio which experienced read error md/raid10: fix memleak of md thread md/raid10: fix memleak for 'conf->bio_split' md/raid10: fix leak of 'r10bio->remaining' for recovery md/raid10: don't BUG_ON() in raise_barrier() md: fix soft lockup in status_resync md: add error_handlers for raid0 and linear md: Use optimal I/O size for last bitmap page md: Fix types in sb writer md: Move sb writer loop to its own function md/raid10: Fix typo in comment (replacment -> replacement) md: make kobj_type structures constant md/raid10: fix null-ptr-deref in raid10_sync_request md/raid10: fix task hung in raid10d
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "nvme updates for Linux 6.4 - drop redundant pci_enable_pcie_error_reporting (Bjorn Helgaas) - validate nvmet module parameters (Chaitanya Kulkarni) - fence TCP socket on receive error (Chris Leech) - fix async event trace event (Keith Busch) - minor cleanups (Chaitanya Kulkarni, zhenwei pi) - fix and cleanup nvmet Identify handling (Damien Le Moal, Christoph Hellwig) - fix double blk_mq_complete_request race in the timeout handler (Lei Yin) - fix irq locking in nvme-fcloop (Ming Lei) - remove queue mapping helper for rdma devices (Sagi Grimberg)" * tag 'nvme-6.4-2023-04-14' of git://git.infradead.org/nvme: nvme-fcloop: fix "inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage" blk-mq-rdma: remove queue mapping helper for rdma devices nvme-rdma: minor cleanup in nvme_rdma_create_cq() nvme: fix double blk_mq_complete_request for timeout request with low probability nvme: fix async event trace event nvme-apple: return directly instead of else nvme-apple: return directly instead of else nvmet-tcp: validate idle poll modparam value nvmet-tcp: validate so_priority modparam value nvme-tcp: fence TCP socket on receive error nvmet: remove nvmet_req_cns_error_complete nvmet: rename nvmet_execute_identify_cns_cs_ns nvmet: fix Identify Identification Descriptor List handling nvmet: cleanup nvmet_execute_identify() nvmet: fix I/O Command Set specific Identify Controller nvmet: fix Identify Active Namespace ID list handling nvmet: fix Identify Controller handling nvmet: fix Identify Namespace handling nvmet: fix error handling in nvmet_execute_identify_cns_cs_ns() nvme-pci: drop redundant pci_enable_pcie_error_reporting()
-
Tom Rix authored
clang with W=1 reports drivers/md/raid5.c:7719:6: error: variable 'working_disks' set but not used [-Werror,-Wunused-but-set-variable] int working_disks = 0; ^ This variable is not used so remove it. Signed-off-by:Tom Rix <trix@redhat.com> Signed-off-by:
Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230327132324.1769595-1-trix@redhat.com
-
Yu Kuai authored
handle_read_error() will resumit r10_bio by raid10_read_request(), which will call bio_start_io_acct() again, while bio_end_io_acct() will only be called once. Fix the problem by don't account io again from handle_read_error(). Fixes: 528bc2cf ("md/raid10: enable io accounting") Suggested-by:
Yu Kuai <yukuai3@huawei.com> Signed-off-by:
-
Yu Kuai authored
In raid10_run(), if setup_conf() succeed and raid10_run() failed before setting 'mddev->thread', then in the error path 'conf->thread' is not freed. Fix the problem by setting 'mddev->thread' right after setup_conf(). Fixes: 43a52123 ("md-cluster: choose correct label when clustered layout is not supported") Signed-off-by:
-
Yu Kuai authored
In the error path of raid10_run(), 'conf' need be freed, however, 'conf->bio_split' is missed and memory will be leaked. Since there are 3 places to free 'conf', factor out a helper to fix the problem. Fixes: fc9977dd ("md/raid10: simplify the splitting of requests.") Signed-off-by:
-
Yu Kuai authored
raid10_sync_request() will add 'r10bio->remaining' for both rdev and replacement rdev. However, if the read io fails, recovery_request_write() returns without issuing the write io, in this case, end_sync_request() is only called once and 'remaining' is leaked, cause an io hang. Fix the problem by decreasing 'remaining' according to if 'bio' and 'repl_bio' is valid. Fixes: 24afd80d ("md/raid10: handle recovery of replacement devices.") Signed-off-by:
-
Yu Kuai authored
If raise_barrier() is called the first time in raid10_sync_request(), which means the first non-normal io is handled, raise_barrier() should wait for all dispatched normal io to be done. This ensures that normal io won't starve. However, BUG_ON() if this is broken is too aggressive. This patch replace BUG_ON() with WARN and fall back to not force. Signed-off-by:
-
Yu Kuai authored
status_resync() will calculate 'curr_resync - recovery_active' to show user a progress bar like following: [============>........] resync = 61.4% 'curr_resync' and 'recovery_active' is updated in md_do_sync(), and status_resync() can read them concurrently, hence it's possible that 'curr_resync - recovery_active' can overflow to a huge number. In this case status_resync() will be stuck in the loop to print a large amount of '=', which will end up soft lockup. Fix the problem by setting 'resync' to MD_RESYNC_ACTIVE in this case, this way resync in progress will be reported to user. Signed-off-by:
-
Mariusz Tkaczyk authored
After the commit 9631abdb("md: Set MD_BROKEN for RAID1 and RAID10") MD_BROKEN must be set if array is failed because state_store() checks it. If it is set then -EBUSY is returned to userspace. For raid0 and linear MD_BROKEN is not set by error_handler(). As a result mdadm is unable to trigger clean-up actions. It is a regression. This patch adds appropriate error_handler for raid0 and linear. The error handler sets MD_BROKEN for this device. Reviewed-by:
Xiao Ni <xni@redhat.com> Signed-off-by:
Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com> Signed-off-by:
-
Jon Derrick authored
If the bitmap space has enough room, size the I/O for the last bitmap page write to the optimal I/O size for the storage device. The expanded write is checked that it won't overrun the data or metadata. The drive this was tested against has higher latencies when there are sub-4k writes due to device-side read-mod-writes of its atomic 4k write unit. This change helps increase performance by sizing the last bitmap page I/O for the device's preferred write unit, if it is given. Example Intel/Solidigm P5520 Raid10, Chunk-size 64M, bitmap-size 57228 bits $ mdadm --create /dev/md0 --level=10 --raid-devices=4 /dev/nvme{0,1,2,3}n1 --assume-clean --bitmap=internal --bitmap-chunk=64M $ fio --name=test --direct=1 --filename=/dev/md0 --rw=randwrite --bs=4k --runtime=60 Without patch: write: IOPS=1676, BW=6708KiB/s (6869kB/s)(393MiB/60001msec); 0 zone resets With patch: write: IOPS=15.7k, BW=61.4MiB/s (64.4MB/s)(3683MiB/60001msec); 0 zone resets Biosnoop: Without patch: Time Process PID Device LBA Size Lat 1.410377 md0_raid10 6900 nvme0n1 W 16 4096 0.02 1.410387 md0_raid10 6900 nvme2n1 W 16 4096 0.02 1.410374 md0_raid10 6900 nvme3n1 W 16 4096 0.01 1.410381 md0_raid10 6900 nvme1n1 W 16 4096 0.02 1.410411 md0_raid10 6900 nvme1n1 W 115346512 4096 0.01 1.410418 md0_raid10 6900 nvme0n1 W 115346512 4096 0.02 1.410915 md0_raid10 6900 nvme2n1 W 24 3584 0.43 <-- 1.410935 md0_raid10 6900 nvme3n1 W 24 3584 0.45 <-- 1.411124 md0_raid10 6900 nvme1n1 W 24 3584 0.64 <-- 1.411147 md0_raid10 6900 nvme0n1 W 24 3584 0.66 <-- 1.411176 md0_raid10 6900 nvme3n1 W 2019022184 4096 0.01 1.411189 md0_raid10 6900 nvme2n1 W 2019022184 4096 0.02 With patch: Time Process PID Device LBA Size Lat 5.747193 md0_raid10 727 nvme0n1 W 16 4096 0.01 5.747192 md0_raid10 727 nvme1n1 W 16 4096 0.02 5.747195 md0_raid10 727 nvme3n1 W 16 4096 0.01 5.747202 md0_raid10 727 nvme2n1 W 16 4096 0.02 5.747229 md0_raid10 727 nvme3n1 W 1196223704 4096 0.02 5.747224 md0_raid10 727 nvme0n1 W 1196223704 4096 0.01 5.747279 md0_raid10 727 nvme0n1 W 24 4096 0.01 <-- 5.747279 md0_raid10 727 nvme1n1 W 24 4096 0.02 <-- 5.747284 md0_raid10 727 nvme3n1 W 24 4096 0.02 <-- 5.747291 md0_raid10 727 nvme2n1 W 24 4096 0.02 <-- 5.747314 md0_raid10 727 nvme2n1 W 2234636712 4096 0.01 5.747317 md0_raid10 727 nvme1n1 W 2234636712 4096 0.02 Reviewed-by:Jon Derrick <jonathan.derrick@linux.dev> Signed-off-by:
-
Jon Derrick authored
Page->index is a pgoff_t and multiplying could cause overflows on a 32-bit architecture. In the sb writer, this is used to calculate and verify the sector being used, and is multiplied by a sector value. Using sector_t will cast it to a u64 type and is the more appropriate type for the unit. Additionally, the integer size unit is converted to a sector unit in later calculations, and is now corrected to be an unsigned type. Finally, clean up the calculations using variable aliases to improve readabiliy. Reviewed-by:
-
Jon Derrick authored
Preparatory patch for optimal I/O size calculation. Move the sb writer loop routine into its own function for clarity. Reviewed-by:
-
Jiangshan Yi authored
Replace replacment with replacement. Signed-off-by:
Jiangshan Yi <yijiangshan@kylinos.cn> Signed-off-by:
-
Thomas Weißschuh authored
Since commit ee6d3dd4 ("driver core: make kobj_type constant.") the driver core allows the usage of const struct kobj_type. Take advantage of this to constify the structure definitions to prevent modification at runtime. Signed-off-by:
Thomas Weißschuh <linux@weissschuh.net> Signed-off-by:
-
Li Nan authored
init_resync() inits mempool and sets conf->have_replacemnt at the beginning of sync, close_sync() frees the mempool when sync is completed. After [1] recovery might be skipped and init_resync() is called but close_sync() is not. null-ptr-deref occurs with r10bio->dev[i].repl_bio. The following is one way to reproduce the issue. 1) create a array, wait for resync to complete, mddev->recovery_cp is set to MaxSector. 2) recovery is woken and it is skipped. conf->have_replacement is set to 0 in init_resync(). close_sync() not called. 3) some io errors and rdev A is set to WantReplacement. 4) a new device is added and set to A's replacement. 5) recovery is woken, A have replacement, but conf->have_replacemnt is 0. r10bio->dev[i].repl_bio will not be alloced and null-ptr-deref occurs. Fix it by not calling init_resync() if recovery skipped. [1] commit 7e83ccbe ("md/raid10: Allow skipping recovery when clean arrays are assembled") Fixes: 7e83ccbe ("md/raid10: Allow skipping recovery when clean arrays are assembled") Cc: stable@vger.kernel.org Signed-off-by:Li Nan <linan122@huawei.com> Signed-off-by:
-
Li Nan authored
commit fe630de0 ("md/raid10: avoid deadlock on recovery.") allowed normal io and sync io to exist at the same time. Task hung will occur as below: T1 T2 T3 T4 raid10d handle_read_error allow_barrier conf->nr_pending-- -> 0 //submit sync io raid10_sync_request raise_barrier ->will not be blocked ... //submit to drivers raid10_read_request wait_barrier conf->nr_pending++ -> 1 //retry read fail raid10_end_read_request reschedule_retry add to retry_list conf->nr_queued++ -> 1 //sync io fail end_sync_read __end_sync_read reschedule_retry add to retry_list conf->nr_queued++ -> 2 ... handle_read_error get form retry_list conf->nr_queued-- freeze_array wait nr_pending == nr_queued+1 ->1 ->2 //task hung retry read and sync io will be added to retry_list(nr_queued->2) if they fails. raid10d() called handle_read_error() and hung in freeze_array(). nr_queued will not decrease because raid10d is blocked, nr_pending will not increase because conf->barrier is not released. Fix it by moving allow_barrier() after raid10_read_request(). raise_barrier() will wait for nr_waiting to become 0. Therefore, sync io and regular io will not be issued at the same time. Also remove the check of nr_queued in stop_waiting_barrier. It can be 0 but don't need to be blocking. Remove the check for MD_RECOVERY_RUNNING as the check is redundent. Fixes: fe630de0 ("md/raid10: avoid deadlock on recovery.") Signed-off-by:
-
- 13 Apr, 2023 15 commits
-
-
Akinobu Mita authored
The null_blk driver has multiple driver-specific fault injection mechanisms. Each fault injection configuration can only be specified by a module parameter and cannot be reconfigured without reloading the driver. Also, each configuration is common to all devices and is initialized every time a new device is added. This change adds the following subdirectories for each null_blk device. /sys/kernel/config/nullb/<disk>/timeout_inject /sys/kernel/config/nullb/<disk>/requeue_inject /sys/kernel/config/nullb/<disk>/init_hctx_fault_inject Each fault injection attribute can be dynamically set per device by a corresponding file in these directories. Signed-off-by:
-
Akinobu Mita authored
This provides a helper function to allow configuration of fault-injection for configfs-based drivers. The config items created by this function have the same interface as the one created under debugfs by fault_create_debugfs_attr(). Signed-off-by:
-
Christoph Hellwig authored
__blk_mq_run_hw_queue just contains a WARN_ON_ONCE for calls from interrupt context and a blk_mq_run_dispatch_ops-protected call to blk_mq_sched_dispatch_requests. Open code the call to blk_mq_sched_dispatch_requests in both callers, and move the WARN_ON_ONCE to blk_mq_run_hw_queue where it can be extended to all !async calls, while the other call is from workqueue context and thus obviously does not need the assert. Signed-off-by:
-
Christoph Hellwig authored
Only blk_mq_run_hw_queue can call __blk_mq_delay_run_hw_queue with async=false, so move the handling there. With this __blk_mq_delay_run_hw_queue can be merged into blk_mq_delay_run_hw_queue. Signed-off-by:
-
Christoph Hellwig authored
For the in-context dispatch, blk_mq_hctx_stopped is alredy checked in blk_mq_sched_dispatch_requests under blk_mq_run_dispatch_ops() protection. For the async dispatch case having a check before scheduling the work still makes sense to avoid needless workqueue scheduling, so just keep it for that case. Signed-off-by:
-
Christoph Hellwig authored
blk_mq_hctx_stopped is already checked in blk_mq_sched_dispatch_requests under blk_mq_run_dispatch_ops() protection, so remove the duplicate check. Signed-off-by:
-
Christoph Hellwig authored
__blk_mq_sched_dispatch_requests currently has duplicated logic for the cases where requests are on the hctx dispatch list or not. Merge the two with a new need_dispatch variable and remove a few pointless local variables. Signed-off-by:
-
Christoph Hellwig authored
Replace the boolean at_head argument with the same flags that are already passed to blk_mq_insert_request. Signed-off-by:
-
Christoph Hellwig authored
Instead of passing a bool at_head, pass down the full flags from the blk_mq_insert_request interface. Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Reviewed-by:
-
Christoph Hellwig authored
Replace the boolean at_head argument with the same flags that are already passed to blk_mq_insert_request. Signed-off-by:
-
Christoph Hellwig authored
Replace the at_head bool with a flags argument that so far only contains a single BLK_MQ_INSERT_AT_HEAD value. This makes it much easier to grep for head insertions into the blk-mq dispatch queues. Signed-off-by:
-
Christoph Hellwig authored
blk_mq_add_to_requeue_list takes a bool parameter to control how to kick the requeue list at the end of the function. Move the call to blk_mq_kick_requeue_list to the callers that want it instead. Signed-off-by:
-
Christoph Hellwig authored
blk_mq_request_bypass_insert takes a bool parameter to control how to run the queue at the end of the function. Move the blk_mq_run_hw_queue call to the callers that want it instead. Signed-off-by:
-
Christoph Hellwig authored
blk_mq_insert_request takes two bool parameters to control how to run the queue at the end of the function. Move the blk_mq_run_hw_queue call to the callers that want it instead. Signed-off-by:
-
Christoph Hellwig authored
Due to the wildly different behavior based on the bypass_insert argument, not a whole lot of code in __blk_mq_try_issue_directly is actually shared between blk_mq_try_issue_directly and blk_mq_request_issue_directly. Remove __blk_mq_try_issue_directly and fold the code into the two callers instead. Signed-off-by:
-
