- 20 Dec, 2018 3 commits
-
-
Yafang Shao authored
This patch adds two sysctl knobs for GRE: net.netfilter.nf_conntrack_gre_timeout = 30 net.netfilter.nf_conntrack_gre_timeout_stream = 180 Update the Documentation as well. Signed-off-by:
Yafang Shao <laoar.shao@gmail.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org>
-
Florian Westphal authored
We have no explicit signal when a UDP stream has terminated, peers just stop sending. For suspected stream connections a timeout of two minutes is sane to keep NAT mapping alive a while longer. It matches tcp conntracks 'timewait' default timeout value. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Florian Westphal authored
Currently DNS resolvers that send both A and AAAA queries from same source port can trigger stream mode prematurely, which results in non-early-evictable conntrack entry for three minutes, even though DNS requests are done in a few milliseconds. Add a two second grace period where we continue to use the ordinary 30-second default timeout. Its enough for DNS request/response traffic, even if two request/reply packets are involved. ASSURED is still set, else conntrack (and thus a possible NAT mapping ...) gets zapped too in case conntrack table runs full. Signed-off-by:
-
- 18 Dec, 2018 4 commits
-
-
Taehee Yoo authored
If same destination IP address config is already existing, that config is just used. MAC address also should be same. However, there is no MAC address checking routine. So that MAC address checking routine is added. test commands: %iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \ -j CLUSTERIP --new --hashmode sourceip \ --clustermac 01:00:5e:00:00:20 --total-nodes 2 --local-node 1 %iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \ -j CLUSTERIP --new --hashmode sourceip \ --clustermac 01:00:5e:00:00:21 --total-nodes 2 --local-node 1 After this patch, above commands are disallowed. Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Taehee Yoo authored
A proc_remove() can sleep. so that it can't be inside of spin_lock. Hence proc_remove() is moved to outside of spin_lock. and it also adds mutex to sync create and remove of proc entry(config->pde). test commands: SHELL#1 %while :; do iptables -A INPUT -p udp -i enp2s0 -d 192.168.1.100 \ --dport 9000 -j CLUSTERIP --new --hashmode sourceip \ --clustermac 01:00:5e:00:00:21 --total-nodes 3 --local-node 3; \ iptables -F; done SHELL#2 %while :; do echo +1 > /proc/net/ipt_CLUSTERIP/192.168.1.100; \ echo -1 > /proc/net/ipt_CLUSTERIP/192.168.1.100; done [ 2949.569864] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99 [ 2949.579944] in_atomic(): 1, irqs_disabled(): 0, pid: 5472, name: iptables [ 2949.587920] 1 lock held by iptables/5472: [ 2949.592711] #0: 000000008f0ebcf2 (&(&cn->lock)->rlock){+...}, at: refcount_dec_and_lock+0x24/0x50 [ 2949.603307] CPU: 1 PID: 5472 Comm: iptables Tainted: G W 4.19.0-rc5+ #16 [ 2949.604212] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015 [ 2949.604212] Call Trace: [ 2949.604212] dump_stack+0xc9/0x16b [ 2949.604212] ? show_regs_print_info+0x5/0x5 [ 2949.604212] ___might_sleep+0x2eb/0x420 [ 2949.604212] ? set_rq_offline.part.87+0x140/0x140 [ 2949.604212] ? _rcu_barrier_trace+0x400/0x400 [ 2949.604212] wait_for_completion+0x94/0x710 [ 2949.604212] ? wait_for_completion_interruptible+0x780/0x780 [ 2949.604212] ? __kernel_text_address+0xe/0x30 [ 2949.604212] ? __lockdep_init_map+0x10e/0x5c0 [ 2949.604212] ? __lockdep_init_map+0x10e/0x5c0 [ 2949.604212] ? __init_waitqueue_head+0x86/0x130 [ 2949.604212] ? init_wait_entry+0x1a0/0x1a0 [ 2949.604212] proc_entry_rundown+0x208/0x270 [ 2949.604212] ? proc_reg_get_unmapped_area+0x370/0x370 [ 2949.604212] ? __lock_acquire+0x4500/0x4500 [ 2949.604212] ? complete+0x18/0x70 [ 2949.604212] remove_proc_subtree+0x143/0x2a0 [ 2949.708655] ? remove_proc_entry+0x390/0x390 [ 2949.708655] clusterip_tg_destroy+0x27a/0x630 [ipt_CLUSTERIP] [ ... ] Fixes: b3e456fc ("netfilter: ipt_CLUSTERIP: fix a race condition of proc file creation") Signed-off-by: -
Taehee Yoo authored
When network namespace is destroyed, both clusterip_tg_destroy() and clusterip_net_exit() are called. and clusterip_net_exit() is called before clusterip_tg_destroy(). Hence cleanup check code in clusterip_net_exit() doesn't make sense. test commands: %ip netns add vm1 %ip netns exec vm1 bash %ip link set lo up %iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \ -j CLUSTERIP --new --hashmode sourceip \ --clustermac 01:00:5e:00:00:20 --total-nodes 2 --local-node 1 %exit %ip netns del vm1 splat looks like: [ 341.184508] WARNING: CPU: 1 PID: 87 at net/ipv4/netfilter/ipt_CLUSTERIP.c:840 clusterip_net_exit+0x319/0x380 [ipt_CLUSTERIP] [ 341.184850] Modules linked in: ipt_CLUSTERIP nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xt_tcpudp iptable_filter bpfilter ip_tables x_tables [ 341.184850] CPU: 1 PID: 87 Comm: kworker/u4:2 Not tainted 4.19.0-rc5+ #16 [ 341.227509] Workqueue: netns cleanup_net [ 341.227509] RIP: 0010:clusterip_net_exit+0x319/0x380 [ipt_CLUSTERIP] [ 341.227509] Code: 0f 85 7f fe ff ff 48 c7 c2 80 64 2c c0 be a8 02 00 00 48 c7 c7 a0 63 2c c0 c6 05 18 6e 00 00 01 e8 bc 38 ff f5 e9 5b fe ff ff <0f> 0b e9 33 ff ff ff e8 4b 90 50 f6 e9 2d fe ff ff 48 89 df e8 de [ 341.227509] RSP: 0018:ffff88011086f408 EFLAGS: 00010202 [ 341.227509] RAX: dffffc0000000000 RBX: 1ffff1002210de85 RCX: 0000000000000000 [ 341.227509] RDX: 1ffff1002210de85 RSI: ffff880110813be8 RDI: ffffed002210de58 [ 341.227509] RBP: ffff88011086f4d0 R08: 0000000000000000 R09: 0000000000000000 [ 341.227509] R10: 0000000000000000 R11: 0000000000000000 R12: 1ffff1002210de81 [ 341.227509] R13: ffff880110625a48 R14: ffff880114cec8c8 R15: 0000000000000014 [ 341.227509] FS: 0000000000000000(0000) GS:ffff880116600000(0000) knlGS:0000000000000000 [ 341.227509] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 341.227509] CR2: 00007f11fd38e000 CR3: 000000013ca16000 CR4: 00000000001006e0 [ 341.227509] Call Trace: [ 341.227509] ? __clusterip_config_find+0x460/0x460 [ipt_CLUSTERIP] [ 341.227509] ? default_device_exit+0x1ca/0x270 [ 341.227509] ? remove_proc_entry+0x1cd/0x390 [ 341.227509] ? dev_change_net_namespace+0xd00/0xd00 [ 341.227509] ? __init_waitqueue_head+0x130/0x130 [ 341.227509] ops_exit_list.isra.10+0x94/0x140 [ 341.227509] cleanup_net+0x45b/0x900 [ ... ] Fixes: 613d0776 ("netfilter: exit_net cleanup check added") Signed-off-by:
-
Taehee Yoo authored
When network namespace is destroyed, cleanup_net() is called. cleanup_net() holds pernet_ops_rwsem then calls each ->exit callback. So that clusterip_tg_destroy() is called by cleanup_net(). And clusterip_tg_destroy() calls unregister_netdevice_notifier(). But both cleanup_net() and clusterip_tg_destroy() hold same lock(pernet_ops_rwsem). hence deadlock occurrs. After this patch, only 1 notifier is registered when module is inserted. And all of configs are added to per-net list. test commands: %ip netns add vm1 %ip netns exec vm1 bash %ip link set lo up %iptables -A INPUT -p tcp -i lo -d 192.168.0.5 --dport 80 \ -j CLUSTERIP --new --hashmode sourceip \ --clustermac 01:00:5e:00:00:20 --total-nodes 2 --local-node 1 %exit %ip netns del vm1 splat looks like: [ 341.809674] ============================================ [ 341.809674] WARNING: possible recursive locking detected [ 341.809674] 4.19.0-rc5+ #16 Tainted: G W [ 341.809674] -------------------------------------------- [ 341.809674] kworker/u4:2/87 is trying to acquire lock: [ 341.809674] 000000005da2d519 (pernet_ops_rwsem){++++}, at: unregister_netdevice_notifier+0x8c/0x460 [ 341.809674] [ 341.809674] but task is already holding lock: [ 341.809674] 000000005da2d519 (pernet_ops_rwsem){++++}, at: cleanup_net+0x119/0x900 [ 341.809674] [ 341.809674] other info that might help us debug this: [ 341.809674] Possible unsafe locking scenario: [ 341.809674] [ 341.809674] CPU0 [ 341.809674] ---- [ 341.809674] lock(pernet_ops_rwsem); [ 341.809674] lock(pernet_ops_rwsem); [ 341.809674] [ 341.809674] *** DEADLOCK *** [ 341.809674] [ 341.809674] May be due to missing lock nesting notation [ 341.809674] [ 341.809674] 3 locks held by kworker/u4:2/87: [ 341.809674] #0: 00000000d9df6c92 ((wq_completion)"%s""netns"){+.+.}, at: process_one_work+0xafe/0x1de0 [ 341.809674] #1: 00000000c2cbcee2 (net_cleanup_work){+.+.}, at: process_one_work+0xb60/0x1de0 [ 341.809674] #2: 000000005da2d519 (pernet_ops_rwsem){++++}, at: cleanup_net+0x119/0x900 [ 341.809674] [ 341.809674] stack backtrace: [ 341.809674] CPU: 1 PID: 87 Comm: kworker/u4:2 Tainted: G W 4.19.0-rc5+ #16 [ 341.809674] Workqueue: netns cleanup_net [ 341.809674] Call Trace: [ ... ] [ 342.070196] down_write+0x93/0x160 [ 342.070196] ? unregister_netdevice_notifier+0x8c/0x460 [ 342.070196] ? down_read+0x1e0/0x1e0 [ 342.070196] ? sched_clock_cpu+0x126/0x170 [ 342.070196] ? find_held_lock+0x39/0x1c0 [ 342.070196] unregister_netdevice_notifier+0x8c/0x460 [ 342.070196] ? register_netdevice_notifier+0x790/0x790 [ 342.070196] ? __local_bh_enable_ip+0xe9/0x1b0 [ 342.070196] ? __local_bh_enable_ip+0xe9/0x1b0 [ 342.070196] ? clusterip_tg_destroy+0x372/0x650 [ipt_CLUSTERIP] [ 342.070196] ? trace_hardirqs_on+0x93/0x210 [ 342.070196] ? __bpf_trace_preemptirq_template+0x10/0x10 [ 342.070196] ? clusterip_tg_destroy+0x372/0x650 [ipt_CLUSTERIP] [ 342.123094] clusterip_tg_destroy+0x3ad/0x650 [ipt_CLUSTERIP] [ 342.123094] ? clusterip_net_init+0x3d0/0x3d0 [ipt_CLUSTERIP] [ 342.123094] ? cleanup_match+0x17d/0x200 [ip_tables] [ 342.123094] ? xt_unregister_table+0x215/0x300 [x_tables] [ 342.123094] ? kfree+0xe2/0x2a0 [ 342.123094] cleanup_entry+0x1d5/0x2f0 [ip_tables] [ 342.123094] ? cleanup_match+0x200/0x200 [ip_tables] [ 342.123094] __ipt_unregister_table+0x9b/0x1a0 [ip_tables] [ 342.123094] iptable_filter_net_exit+0x43/0x80 [iptable_filter] [ 342.123094] ops_exit_list.isra.10+0x94/0x140 [ 342.123094] cleanup_net+0x45b/0x900 [ ... ] Fixes: 202f59af ("netfilter: ipt_CLUSTERIP: do not hold dev") Signed-off-by:
-
- 17 Dec, 2018 13 commits
-
-
Phil Sutter authored
If just a table name was given, nf_tables_dump_rules() continued over the list of tables even after a match was found. The simple fix is to exit the loop if it reached the bottom and ctx->table was not NULL. When iterating over the table's chains, the same problem as above existed. But worse than that, if a chain name was given the hash table wasn't used to find the corresponding chain. Fix this by introducing a helper function iterating over a chain's rules (and taking care of the cb->args handling), then introduce a shortcut to it if a chain name was given. Signed-off-by:
Phil Sutter <phil@nwl.cc> Signed-off-by:
-
Alin Nastac authored
Each media stream negotiation between 2 SIP peers will trigger creation of 4 different expectations (2 RTP and 2 RTCP): - INVITE will create expectations for the media packets sent by the called peer - reply to the INVITE will create expectations for media packets sent by the caller The dport used by these expectations usually match the ones selected by the SIP peers, but they might get translated due to conflicts with another expectation. When such event occur, it is important to do this translation in both directions, dport translation on the receiving path and sport translation on the sending path. This commit fixes the sport translation when the peer requiring it is also the one that starts the media stream. In this scenario, first media stream packet is forwarded from LAN to WAN and will rely on nf_nat_sip_expected() to do the necessary sport translation. However, the expectation matched by this packet does not contain the necessary information for doing SNAT, this data being stored in the paired expectation created by the sender's SIP message (INVITE or reply to it). Signed-off-by:
Alin Nastac <alin.nastac@gmail.com> Signed-off-by:
-
Florian Westphal authored
This removes the (now empty) nf_nat_l4proto struct, all its instances and all the no longer needed runtime (un)register functionality. nf_nat_need_gre() can be axed as well: the module that calls it (to load the no-longer-existing nat_gre module) also calls other nat core functions. GRE nat is now always available if kernel is built with it. Signed-off-by:
-
Florian Westphal authored
This removes the last l4proto indirection, the two callers, the l3proto packet mangling helpers for ipv4 and ipv6, now call the nf_nat_l4proto_manip_pkt() helper. nf_nat_proto_{dccp,tcp,sctp,gre,icmp,icmpv6} are left behind, even though they contain no functionality anymore to not clutter this patch. Next patch will remove the empty files and the nf_nat_l4proto struct. nf_nat_proto_udp.c is renamed to nf_nat_proto.c, as it now contains the other nat manip functionality as well, not just udp and udplite. Signed-off-by: -
Florian Westphal authored
all protocols did set this to nf_nat_l4proto_nlattr_to_range, so just call it directly. The important difference is that we'll now also call it for protocols that we don't support (i.e., nf_nat_proto_unknown did not provide .nlattr_to_range). However, there should be no harm, even icmp provided this callback. If we don't implement a specific l4nat for this, nothing would make use of this information, so adding a big switch/case construct listing all supported l4protocols seems a bit pointless. This change leaves a single function pointer in the l4proto struct. Signed-off-by:
-
Florian Westphal authored
With exception of icmp, all of the l4 nat protocols set this to nf_nat_l4proto_in_range. Get rid of this and just check the l4proto in the caller. Signed-off-by:
-
Florian Westphal authored
No need for indirections here, we only support ipv4 and ipv6 and the called functions are very small. Signed-off-by:
-
Florian Westphal authored
fold remaining users (icmp, icmpv6, gre) into nf_nat_l4proto_unique_tuple. The static-save of old incarnation of resolved key in gre and icmp is removed as well, just use the prandom based offset like the others. Signed-off-by:
-
Florian Westphal authored
almost all l4proto->unique_tuple implementations just call this helper, so make ->unique_tuple() optional and call its helper directly if the l4proto doesn't override it. This is an intermediate step to get rid of ->unique_tuple completely. Signed-off-by:
-
Florian Westphal authored
Historically this was net_random() based, and was then converted to a hash based algorithm (private boot seed + hash of endpoint addresses) due to concerns of leaking net_random() bits. RANDOM_FULLY mode was added later to avoid problems with hash based mode (see commit 34ce3240, "netfilter: nf_nat: add full port randomization support" for details). Just make prandom_u32() the default search starting point and get rid of ->secure_port() altogether. Signed-off-by:
-
Yafang Shao authored
These parameters aren't used now. So remove them. Signed-off-by:
-
Florian Westphal authored
In case almost or all available ports are taken, clash resolution can take a very long time, resulting in soft lockup. This can happen when many to-be-natted hosts connect to same destination:port (e.g. a proxy) and all connections pass the same SNAT. Pick a random offset in the acceptable range, then try ever smaller number of adjacent port numbers, until either the limit is reached or a useable port was found. This results in at most 248 attempts (128 + 64 + 32 + 16 + 8, i.e. 4 restarts with new search offset) instead of 64000+, Signed-off-by:
-
Xiaozhou Liu authored
Since a pseudo-random starting point is used in finding a port in the default case, that 'else if' branch above is no longer a necessity. So remove it to simplify code. Signed-off-by:
Xiaozhou Liu <liuxiaozhou@bytedance.com> Signed-off-by:
-
- 13 Dec, 2018 2 commits
-
-
Qian Cai authored
To make overflows as obvious as possible and to prevent code from blithely proceeding with a truncated string. This also has a side-effect to fix a compilation warning when using GCC 8.2.1. net/netfilter/ipset/ip_set_core.c: In function 'ip_set_sockfn_get': net/netfilter/ipset/ip_set_core.c:2027:3: warning: 'strncpy' writing 32 bytes into a region of size 2 overflows the destination [-Wstringop-overflow=] Signed-off-by:
Qian Cai <cai@gmx.us> Signed-off-by:
Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by:
-
Florent Fourcot authored
New function added by "Introduction of new commands and protocol version 7" is not working, since we return skb2 to user Signed-off-by:
Victorien Molle <victorien.molle@wifirst.fr> Signed-off-by:
Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by:
-
- 01 Dec, 2018 3 commits
-
-
Florian Westphal authored
This is a leftover from days where single-cpu systems were common: Store last port used to resolve a clash to use it as a starting point when the next conflict needs to be resolved. When we have parallel attempt to connect to same address:port pair, its likely that both cores end up computing the same "available" port, as both use same starting port, and newly used ports won't become visible to other cores until the conntrack gets confirmed later. One of the cores then has to drop the packet at insertion time because the chosen new tuple turns out to be in use after all. Lets simplify this: remove port rover and use a pseudo-random starting point. Note that this doesn't make netfilter default to 'fully random' mode; the 'rover' was only used if NAT could not reuse source port as-is. Signed-off-by:
-
Pablo Neira Ayuso authored
These are very very (for long time unused) caching infrastructure definition, remove then. They have nothing to do with the NFC subsystem. Signed-off-by: -
Paul E. McKenney authored
Now that call_rcu()'s callback is not invoked until after bh-disable regions of code have completed (in addition to explicitly marked RCU read-side critical sections), call_rcu() can be used in place of call_rcu_bh(). Similarly, rcu_barrier() can be used in place of rcu_barrier_bh() and synchronize_rcu() in place of synchronize_rcu_bh(). This commit therefore makes these changes. Signed-off-by:
Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by:
-
- 12 Nov, 2018 6 commits
-
-
Taehee Yoo authored
nf_flow_offload_gc_step() and nf_flow_table_iterate() are very similar. so that many duplicate code can be removed. After this patch, nf_flow_offload_gc_step() is simple callback function of nf_flow_table_iterate() like nf_flow_table_do_cleanup(). Signed-off-by:
-
Taehee Yoo authored
nf_flow_table_iterate() is local function, make it static. Signed-off-by:
-
Andreas Jaggi authored
Useful to only set a particular range of the conntrack mark while leaving existing parts of the value alone, e.g. when updating conntrack marks via netlink from userspace. For NFQUEUE it was already implemented in commit 534473c6 ("netfilter: ctnetlink: honor CTA_MARK_MASK when setting ctmark"). This now adds the same functionality also for the other netlink conntrack mark changes. Signed-off-by:
Andreas Jaggi <andreas.jaggi@waterwave.ch> Signed-off-by:
-
git://blackhole.kfki.hu/nf-nextPablo Neira Ayuso authored
Jozsef Kadlecsik says: ==================== - Introduction of new commands and thus protocol version 7. The new commands makes possible to eliminate the getsockopt interface of ipset and use solely netlink to communicate with the kernel. Due to the strict attribute checking both in user/kernel space, a new protocol number was introduced. Both the kernel/userspace is fully backward compatible. - Make invalid MAC address checks consisten, from Stefano Brivio. The patch depends on the next one. - Allow matching on destination MAC address for mac and ipmac sets, also from Stefano Brivio. ==================== Signed-off-by: -
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/phy/marvell.c: In function 'm88e1510_config_init': drivers/net/phy/marvell.c:850:7: warning: variable 'pause' set but not used [-Wunused-but-set-variable] It not used any more after commit 3c1bcc86 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
-
- 11 Nov, 2018 9 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "One last pull request before heading to Vancouver for LPC, here we have: 1) Don't forget to free VSI contexts during ice driver unload, from Victor Raj. 2) Don't forget napi delete calls during device remove in ice driver, from Dave Ertman. 3) Don't request VLAN tag insertion of ibmvnic device when SKB doesn't have VLAN tags at all. 4) IPV4 frag handling code has to accomodate the situation where two threads try to insert the same fragment into the hash table at the same time. From Eric Dumazet. 5) Relatedly, don't flow separate on protocol ports for fragmented frames, also from Eric Dumazet. 6) Memory leaks in qed driver, from Denis Bolotin. 7) Correct valid MTU range in smsc95xx driver, from Stefan Wahren. 8) Validate cls_flower nested policies properly, from Jakub Kicinski. 9) Clearing of stats counters in mc88e6xxx driver doesn't retain important bits in the G1_STATS_OP register causing the chip to hang. Fix from Andrew Lunn" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits) act_mirred: clear skb->tstamp on redirect net: dsa: mv88e6xxx: Fix clearing of stats counters tipc: fix link re-establish failure net: sched: cls_flower: validate nested enc_opts_policy to avoid warning net: mvneta: correct typo flow_dissector: do not dissect l4 ports for fragments net: qualcomm: rmnet: Fix incorrect assignment of real_dev net: aquantia: allow rx checksum offload configuration net: aquantia: invalid checksumm offload implementation net: aquantia: fixed enable unicast on 32 macvlan net: aquantia: fix potential IOMMU fault after driver unbind net: aquantia: synchronized flow control between mac/phy net: smsc95xx: Fix MTU range net: stmmac: Fix RX packet size > 8191 qed: Fix potential memory corruption qed: Fix SPQ entries not returned to pool in error flows qed: Fix blocking/unlimited SPQ entries leak qed: Fix memory/entry leak in qed_init_sp_request() inet: frags: better deal with smp races net: hns3: bugfix for not checking return value ... -
Linus Torvalds authored
Merge tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - fix build errors in binrpm-pkg and bindeb-pkg targets - fix false positive matches in merge_config.sh - fix build version mismatch in deb-pkg target - fix dtbs_install handling in (bin)deb-pkg target - revert a commit that allows setlocalversion to write to source tree * tag 'kbuild-fixes-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: builddeb: Fix inclusion of dtbs in debian package Revert "scripts/setlocalversion: git: Make -dirty check more robust" kbuild: deb-pkg: fix too low build version number kconfig: merge_config: avoid false positive matches from comment lines kbuild: deb-pkg: fix bindeb-pkg breakage when O= is used kbuild: rpm-pkg: fix binrpm-pkg breakage when O= is used
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linuxLinus Torvalds authored
Pull btrfs fixes from David Sterba: "Several fixes to recent release (4.19, fixes tagged for stable) and other fixes" * tag 'for-4.20-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: Btrfs: fix missing delayed iputs on unmount Btrfs: fix data corruption due to cloning of eof block Btrfs: fix infinite loop on inode eviction after deduplication of eof block Btrfs: fix deadlock on tree root leaf when finding free extent btrfs: avoid link error with CONFIG_NO_AUTO_INLINE btrfs: tree-checker: Fix misleading group system information Btrfs: fix missing data checksums after a ranged fsync (msync) btrfs: fix pinned underflow after transaction aborted Btrfs: fix cur_offset in the error case for nocow
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "A large number of ext4 bug fixes, mostly buffer and memory leaks on error return cleanup paths" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: missing !bh check in ext4_xattr_inode_write() ext4: fix buffer leak in __ext4_read_dirblock() on error path ext4: fix buffer leak in ext4_expand_extra_isize_ea() on error path ext4: fix buffer leak in ext4_xattr_move_to_block() on error path ext4: release bs.bh before re-using in ext4_xattr_block_find() ext4: fix buffer leak in ext4_xattr_get_block() on error path ext4: fix possible leak of s_journal_flag_rwsem in error path ext4: fix possible leak of sbi->s_group_desc_leak in error path ext4: remove unneeded brelse call in ext4_xattr_inode_update_ref() ext4: avoid possible double brelse() in add_new_gdb() on error path ext4: avoid buffer leak in ext4_orphan_add() after prior errors ext4: avoid buffer leak on shutdown in ext4_mark_iloc_dirty() ext4: fix possible inode leak in the retry loop of ext4_resize_fs() ext4: fix missing cleanup if ext4_alloc_flex_bg_array() fails while resizing ext4: add missing brelse() update_backups()'s error path ext4: add missing brelse() add_new_gdb_meta_bg()'s error path ext4: add missing brelse() in set_flexbg_block_bitmap()'s error path ext4: avoid potential extra brelse in setup_new_flex_group_blocks()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A set of x86 fixes: - Cure the LDT remapping to user space on 5 level paging which ended up in the KASLR space - Remove LDT mapping before freeing the LDT pages - Make NFIT MCE handling more robust - Unbreak the VSMP build by removing the dependency on paravirt ops - Support broken PIT emulation on Microsoft hyperV - Don't trace vmware_sched_clock() to avoid tracer recursion - Remove -pipe from KBUILD CFLAGS which breaks clang and is also slower on GCC - Trivial coding style and typo fixes" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/cpu/vmware: Do not trace vmware_sched_clock() x86/vsmp: Remove dependency on pv_irq_ops x86/ldt: Remove unused variable in map_ldt_struct() x86/ldt: Unmap PTEs for the slot before freeing LDT pages x86/mm: Move LDT remap out of KASLR region on 5-level paging acpi/nfit, x86/mce: Validate a MCE's address before using it acpi/nfit, x86/mce: Handle only uncorrectable machine checks x86/build: Remove -pipe from KBUILD_CFLAGS x86/hyper-v: Fix indentation in hv_do_fast_hypercall16() Documentation/x86: Fix typo in zero-page.txt x86/hyper-v: Enable PIT shutdown quirk clockevents/drivers/i8253: Add support for PIT shutdown quirk -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "A bunch of perf tooling fixes: - Make the Intel PT SQL viewer more robust - Make the Intel PT debug log more useful - Support weak groups in perf record so it's behaving the same way as perf stat - Display the LBR stats in callchain entries properly in perf top - Handle different PMu names with common prefix properlin in pert stat - Start syscall augmenting in perf trace. Preparation for architecture independent eBPF instrumentation of syscalls. - Fix build breakage in JVMTI perf lib - Fix arm64 tools build failure wrt smp_load_{acquire,release}" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf tools: Do not zero sample_id_all for group members perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so perf beauty: Use SRCARCH, ARCH=x86_64 must map to "x86" to find the headers perf intel-pt: Add MTC and CYC timestamps to debug log perf intel-pt: Add more event information to debug log perf scripts python: exported-sql-viewer.py: Fix table find when table re-ordered perf scripts python: exported-sql-viewer.py: Add help window perf scripts python: exported-sql-viewer.py: Add Selected branches report perf scripts python: exported-sql-viewer.py: Fall back to /usr/local/lib/libxed.so perf top: Display the LBR stats in callchain entry perf stat: Handle different PMU names with common prefix perf record: Support weak groups perf evlist: Move perf_evsel__reset_weak_group into evlist perf augmented_syscalls: Start collecting pathnames in the BPF program perf trace: Fix setting of augmented payload when using eBPF + raw_syscalls perf trace: When augmenting raw_syscalls plug raw_syscalls:sys_exit too perf examples bpf: Start augmenting raw_syscalls:sys_{start,exit} tools headers barrier: Fix arm64 tools build failure wrt smp_load_{acquire,release} -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fix from Thomas Gleixner: "Just the removal of a redundant call into the sched deadline overrun check" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: posix-cpu-timers: Remove useless call to check_dl_overrun()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Thomas Gleixner: "Two small scheduler fixes: - Take hotplug lock in sched_init_smp(). Technically not really required, but lockdep will complain other. - Trivial comment fix in sched/fair" * 'sched/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: Fix a comment in task_numa_fault() sched/core: Take the hotplug lock in sched_init_smp()
-
