- 07 Jan, 2009 40 commits
-
-
Alan Stern authored
This patch (as1192) rearranges the USB PCI host controller suspend and resume and resume routines: Use pci_wake_from_d3() for enabling and disabling wakeup, instead of pci_enable_wake(). Carry out the actual state change while interrupts are disabled. Change the order of the preparations to agree with the general recommendation for PCI devices, instead of messing around with the wakeup settings while the device is in D3. In .suspend: Call the underlying driver to disable IRQ generation; pci_wake_from_d3(device_may_wakeup()); pci_disable_device(); In .suspend_late: pci_save_state(); pci_set_power_state(D3hot); (for PPC_PMAC) Disable ASIC clocks In .resume_early: (for PPC_PMAC) Enable ASIC clocks pci_set_power_state(D0); pci_restore_state(); In .resume: pci_enable_device(); pci_set_master(); pci_wake_from_d3(0); Call the underlying driver to reenable IRQ generation Add the necessary .suspend_late and .resume_early method pointers to the PCI host controller drivers. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
This patch (as1194) makes usb-storage set the CAPACITY_HEURISTICS flag for all devices made by Nokia, Nikon, or Motorola. These companies seem to include the READ CAPACITY bug in all of their devices. Since cell phones and digital cameras rely on flash storage, which always has an even number of sectors, setting CAPACITY_HEURISTICS shouldn't cause any problems. Not even if the companies wise up and start making devices without the bug. A large number of unusual_devs entries are now unnecessary, so the patch removes them. Signed-off-by:
-
Alan Stern authored
This patch (as1190) makes usb-storage's "quirks=" module parameter writable, so that users can add entries for their devices at runtime with no need to reboot or reload usb-storage. New codes are added for the SANE_SENSE, CAPACITY_HEURISTICS, and CAPACITY_OK flags. Signed-off-by:
-
Alan Stern authored
This patch (as1189b) adds some hacks to usb-storage for dealing with the growing problems involving bad capacity values and last-sector accesses: A new flag, US_FL_CAPACITY_OK, is created to indicate that the device is known to report its capacity correctly. An unusual_devs entry for Linux's own File-backed Storage Gadget is added with this flag set, since g_file_storage always reports the correct capacity and since the capacity need not be even (it is determined by the size of the backing file). An entry in unusual_devs.h which has only the CAPACITY_OK flag set shouldn't prejudice libusual, since the device will work perfectly well with either usb-storage or ub. So a new macro, COMPLIANT_DEV, is added to let libusual know about these entries. When a last-sector access succeeds and the total number of sectors is odd (the unexpected case, in which guessing that the number is even might cause trouble), a WARN is triggered. The kerneloops.org project will collect these warnings, allowing us to add CAPACITY_OK flags for the devices in question before implementing the default-to-even heuristic. If users want to prevent the stack dump produced by the WARN, they can disable the hack by adding an unusual_devs entry for their device with the CAPACITY_OK flag. When a last-sector access fails three times in a row and neither the FIX_CAPACITY nor the CAPACITY_OK flag is set, we assume the last-sector bug is present. We replace the existing status and sense data with values that will cause the SCSI core to fail the access immediately rather than retry indefinitely. This should fix the difficulties people have been having with Nokia phones. Signed-off-by:
-
David Brownell authored
Add driver for the high speed USB-OTG transceiver in TI's TWL4030 family of chips. Given this and various other pending patches, OMAP3 hardware like that from beagleboard.org, gumstix.com (Overo), and openpandora.org should now have basic USB host and peripheral connectivity with mainline kernels. Ditto for less widely-available boards. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Darius Augulis authored
Implementation of USB device driver integrated in Freescale's i.MXL processor. Adds USB device driver for i.MXL. Signed-off-by:
Darius Augulis <augulis.darius@gmail.com> Signed-off-by:
-
Oliver Neukum authored
This extension allows unpoisoning an anchor allowing drivers that resubmit URBs to reuse an anchor for methods like resume() Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Thomas Hommel authored
There is no need to disable port 1 on ISP1761. That port could be used as an OTG port which would require a different init sequence. However we don't have OTG support (yet) so we can use it as a normal USB port. This patch allows port 1 to be used a normal Port on the ISP1761. Signed-off-by:
Thomas Hommel <Thomas.Hommel@gefanuc.com> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Dan Williams authored
Many newer Option mobile broadband devices initially provide a usb-storage "driver CD" device that's pretty useless on Linux since any software on it most likely wouldn't be compatible with your kernel or distro anyway. Thus, by default just kill the driver CD device by sending the SCSI 'rezero' command, but allow override of the default behavior via usb-storage module parameter so users can keep the ZeroCD device if they really want to. Inspired by the Sierra TruInstall patch. Signed-off-by:
Dan Williams <dcbw@redhat.com> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Cc: Peter Henn <p.henn@option.com Cc: Denis Joseph Barrow <D.Barow@option.com> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Ming Lei authored
It is enough to protect accesses to reject field of urb by marking it as atomic_t,also it is the only reason of existence of usb_reject_lock,so remove the lock to make code more clean. Signed-off-by:
Ming Lei <tom.leiming@gmail.com> Acked-off-by:
-
Alan Stern authored
This patch (as1185) makes usbcore take advantage of the bus notifications sent out by the driver core. Now we can create all our device and interface attribute files before the device or interface uevent is broadcast. A side effect is that we no longer create the endpoint "pseudo" devices at the same time as a device or interface is registered -- it seems like a bad idea to try registering an endpoint before the registration of its parent is complete. So the routines for creating and removing endpoint devices have been split out and renamed, and they are called explicitly when needed. A new bitflag is used for keeping track of whether or not the interface's endpoint devices have been created, since (just as with the interface attributes) they vary with the altsetting and hence can be changed at random times. Signed-off-by:
-
Wu Fengguang authored
USB: make printk messages more searchable Make USB printk messages long and straightforward. One of these decorated USB error messages cost me non-trivial efforts to locate. Signed-off-by:
Wu Fengguang <fengguang.wu@intel.com> Signed-off-by:
-
Bryan Wu authored
Signed-off-by:
Bryan Wu <cooloney@kernel.org> Signed-off-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Bryan Wu authored
Don't redefine the functions in musb driver Signed-off-by:
-
Bryan Wu authored
Signed-off-by:
-
Bryan Wu authored
Some config registers are not avaiable in Blackfin, we have to comment them out. v1-v2: - remove Blackfin specific header file - add Blackfin register version to musb_regs.h header file Signed-off-by:
-
Bryan Wu authored
- DMA registers in Blackfin have different layout - DMA interrupt flags need to be cleared by software Signed-off-by:
-
Bryan Wu authored
add Blackfin version low level register accessing helper functions Signed-off-by:
-
Robin Getz authored
Make sure we program the correct values in only when necessary. Signed-off-by:
Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by:
-
Bryan Wu authored
- replace MUSB_FIFOSIZE register to MUSB_TXCOUNT, cause no MUSB_FIFOSIZE register on Blackfin - use #ifdef to replace #if defined() Signed-off-by:
-
Bryan Wu authored
Signed-off-by:
-
Alan Stern authored
The DPCM subdriver is a little peculiar, in that it's meant to support devices where LUN 0 is Compact Flash and uses the CB transport whereas LUN 1 is SmartMedia and uses the SDDR09 transport. Thus DPCM isn't really a transport in itself; it's more like a demultiplexer. Much of the DPCM code is part of the SDDR09 subdriver already, and the remaining part is fairly small. This patch (as1182) moves that extra piece into sddr09.c, thereby eliminating dpcm.c. Also eliminated is the Kconfig entry for DPCM support; it is now listed as part of the SDDR09 entry. In order to make sure that the semantics are the same as before, each unusual_devs entry for DPCM is now present twice: once with DPCM support if SDDR09 is configured (as before), and once with the SINGLE_LUN flag and CB support otherwise. Signed-off-by:
-
Greg Kroah-Hartman authored
This should speed up the option driver's upload speed quite a bit. It has been tested by a number of different people on different devices with success. Cc: Roland Wolters <roland.wolters@credativ.de> Signed-off-by: -
Greg Kroah-Hartman authored
Some of the usb-serial drivers are starting to use urb->status in ways they should not be doing. This fixes up some of them to prevent that. Signed-off-by: -
Karl Bongers authored
Contains fixes so probe on x86 PCI runs, apparently I'm first to try this. Several fixes to memory access to probe host scratch register. Previously would bug check on chip_addr var used uninitialized. Scratch reg write failed in one instance due to 16-bit initial access mode, so added "& 0x0000ffff" to the readl as fix. Includes some general cleanup - remove global vars, organize memory map resource use. Signed-off-by:
Karl Bongers <kbongers@jged.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
this driver can't handle (of course) any brdige class devices. So we now are just active on one specific bridge which should be only the isp1761 chip behind a PLX bridge. Signed-off-by:
Karl Bongers <kblists08@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by:
-
Felipe Balbi authored
In some obscure scenarios e.g. passing a 0-byte backing file storage, wait_for_completion() would wait forever in fsg_cleanup(). Prevent it by completing the thread in fsg_bind() error path. Signed-off-by:
-
Roel Kluin authored
Sparse asked whether these could be static. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Alan Stern authored
This patch (as1177) modifies the USB core suspend and resume routines. The resume functions now will take a pm_message_t argument, so they will know what sort of resume is occurring. The new argument is also passed to the port suspend/resume and bus suspend/resume routines (although they don't use it for anything but debugging). In addition, special pm_message_t values are used for user-initiated, device-initiated (i.e., remote wakeup), and automatic suspend/resume. By testing these values, drivers can tell whether or not a particular suspend was an autosuspend. Unfortunately, they can't do the same for resumes -- not until the pm_message_t argument is also passed to the drivers' resume methods. That will require a bigger change. IMO, the whole Power Management framework should have been set up this way in the first place. Signed-off-by:
-
Alan Stern authored
This patch (as1178) uses the new round_jiffies_up_relative() routine for setting the autosuspend delayed_work timer. It's appropriate since we don't care too much about the exact length of the delay, but we don't want it to be too short (rounded down). Signed-off-by:
-
Tony Lindgren authored
Move otg_get/set/put_transceiver() from omap specific code to common otg.c so other upcoming drivers can share them. [ dbrownell@users.sourceforge.net: move to drivers/usb/otg, dox ] Signed-off-by:
Felipe Balbi <me@felipebalbi.com> Signed-off-by:
Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by:
-
Philipp Zabel authored
As Russell King points out, calling put_device(otg_transceiver->dev) directly in driver cleanup paths makes assumptions about otg_transceiver internals. Signed-off-by:
-
Philipp Zabel authored
gpio_vbus provides simple GPIO VBUS sensing for peripheral controllers with an internal transceiver. Optionally, a second GPIO can be used to control D+ pullup. It also interfaces with the regulator framework to limit charging currents when powered via USB. gpio_vbus requests the regulator supplying "vbus_draw" and can enable/disable it or limit its current depending on USB state. [dbrownell@users.sourceforge.net: use drivers/otg, cleanups ] Signed-off-by:
-
David Brownell authored
This moves the isp1301-omap driver from the drivers/i2c/chips directory (which will be shrinking) into a new drivers/usb/otg directory (which will grow, with more drivers and utilities). Note that OTG infrastructure needs to be initialized before either host or peripheral side USB support, and may be needed before for pure host or pure peripheral configurations. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Ben Dooks authored
Change the gpio code in the s3c2410_udc to use the generic gpio calls instead of the s3c24xx specific gpio functions. Signed-off-by:
Ben Dooks <ben-linux@fluff.org> Signed-off-by:
-
David Brownell authored
Some code in the pxa25x_udc driver wrongly expects the value of is_vbus_present() to be 0/1, not zero/nonzero ... cope. Issue noted by Jaya Kumar <jayakumar.lkml@gmail.com> This bug has been around since July 2007, and has a simple workaround: unplug the Linux gadget, then re-plug it. Signed-off-by:
-
Felipe Balbi authored
Without it, in platforms that don't provide irq_chip.set_wake(), like omap, musb will WARN() on driver removal. Signed-off-by:
-
Felipe Balbi authored
Trivial patch adding musb's git tree to MAINTAINERS file. Signed-off-by:
-
David Brownell authored
Random host-side MUSB updates, mostly relating to better diagnostics: + Improve diagnostics on host side: - tx flush fifo: * Avoid hundreds of duplicate TX FIFONOTEMPTY messages * make "Can't flush TX fifo" a warning, and say which endpoint - giveback: * use correct status code * show completion function name not just URB pointer - Fix annoying "1 bytes" (should be "1 byte") + Be more consistent about failing init of unusable fifo_mode It's not clear why that "can't flush TX fifo" message appears, though it might relate to disconnection; I see it not infrequently Signed-off-by: -
David Brownell authored
Minor locking fix for musb_hdrc on OMAP3 and OMAP2430: don't read DEVCTL without holding the spinlock, since an IRQ could come in and corrupt things. Signed-off-by:
-
