- 19 Mar, 2019 10 commits
-
-
Masaru Nagai authored
[ Upstream commit ae9819e3 ] Hardware has the CBS (Credit Based Shaper) which affects only Q3 and Q2. When updating the CBS settings, even if the driver does so after waiting for Tx DMA finished, there is a possibility that frame data still remains in TxFIFO. To avoid this, decrease TxFIFO depth of Q3 and Q2 to one. This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM and UDP_STREAM tests run on an Ebisu board. No performance change was detected, outside of noise in the tests, both in terms of throughput and CPU utilisation. Fixes: c156633f ("Renesas Ethernet AVB driver proper") Signed-off-by:
Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by:
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> [simon: updated changelog] Signed-off-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Xin Long authored
[ Upstream commit 9417d81f ] sk_setup_caps() is called to set sk->sk_dst_cache in pptp_connect, so we have to dst_release(sk->sk_dst_cache) in pptp_sock_destruct, otherwise, the dst refcnt will leak. It can be reproduced by this syz log: r1 = socket$pptp(0x18, 0x1, 0x2) bind$pptp(r1, &(0x7f0000000100)={0x18, 0x2, {0x0, @local}}, 0x1e) connect$pptp(r1, &(0x7f0000000000)={0x18, 0x2, {0x3, @remote}}, 0x1e) Consecutive dmesg warnings will occur: unregister_netdevice: waiting for lo to become free. Usage count = 1 v1->v2: - use rcu_dereference_protected() instead of rcu_dereference_check(), as suggested by Eric. Fixes: 00959ade ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)") Reported-by:
Xiumei Mu <xmu@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit ee74d0bd ] In case x25_connect() fails and frees the socket neighbour, we also need to undo the change done to x25->state. Before my last bug fix, we had use-after-free so this patch fixes a latent bug. syzbot report : kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] PREEMPT SMP KASAN CPU: 1 PID: 16137 Comm: syz-executor.1 Not tainted 5.0.0+ #117 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:x25_write_internal+0x1e8/0xdf0 net/x25/x25_subr.c:173 Code: 00 40 88 b5 e0 fe ff ff 0f 85 01 0b 00 00 48 8b 8b 80 04 00 00 48 ba 00 00 00 00 00 fc ff df 48 8d 79 1c 48 89 fe 48 c1 ee 03 <0f> b6 34 16 48 89 fa 83 e2 07 83 c2 03 40 38 f2 7c 09 40 84 f6 0f RSP: 0018:ffff888076717a08 EFLAGS: 00010207 RAX: ffff88805f2f2292 RBX: ffff8880a0ae6000 RCX: 0000000000000000 kobject: 'loop5' (0000000018d0d0ee): kobject_uevent_env RDX: dffffc0000000000 RSI: 0000000000000003 RDI: 000000000000001c RBP: ffff888076717b40 R08: ffff8880950e0580 R09: ffffed100be5e46d R10: ffffed100be5e46c R11: ffff88805f2f2363 R12: ffff888065579840 kobject: 'loop5' (0000000018d0d0ee): fill_kobj_path: path = '/devices/virtual/block/loop5' R13: 1ffff1100ece2f47 R14: 0000000000000013 R15: 0000000000000013 FS: 00007fb88cf43700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f9a42a41028 CR3: 0000000087a67000 CR4: 00000000001406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: x25_release+0xd0/0x340 net/x25/af_x25.c:658 __sock_release+0xd3/0x2b0 net/socket.c:579 sock_close+0x1b/0x30 net/socket.c:1162 __fput+0x2df/0x8d0 fs/file_table.c:278 ____fput+0x16/0x20 fs/file_table.c:309 task_work_run+0x14a/0x1c0 kernel/task_work.c:113 get_signal+0x1961/0x1d50 kernel/signal.c:2388 do_signal+0x87/0x1940 arch/x86/kernel/signal.c:816 exit_to_usermode_loop+0x244/0x2c0 arch/x86/entry/common.c:162 prepare_exit_to_usermode arch/x86/entry/common.c:197 [inline] syscall_return_slowpath arch/x86/entry/common.c:268 [inline] do_syscall_64+0x52d/0x610 arch/x86/entry/common.c:293 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x457f29 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fb88cf42c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: fffffffffffffe00 RBX: 0000000000000003 RCX: 0000000000457f29 RDX: 0000000000000012 RSI: 0000000020000080 RDI: 0000000000000004 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fb88cf436d4 R13: 00000000004be462 R14: 00000000004cec98 R15: 00000000ffffffff Modules linked in: Fixes: 95d6ebd5 ("net/x25: fix use-after-free in x25_device_event()") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 95d6ebd5 ] In case of failure x25_connect() does a x25_neigh_put(x25->neighbour) but forgets to clear x25->neighbour pointer, thus triggering use-after-free. Since the socket is visible in x25_list, we need to hold x25_list_lock to protect the operation. syzbot report : BUG: KASAN: use-after-free in x25_kill_by_device net/x25/af_x25.c:217 [inline] BUG: KASAN: use-after-free in x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252 Read of size 8 at addr ffff8880a030edd0 by task syz-executor003/7854 CPU: 0 PID: 7854 Comm: syz-executor003 Not tainted 5.0.0+ #97 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 __asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135 x25_kill_by_device net/x25/af_x25.c:217 [inline] x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93 __raw_notifier_call_chain kernel/notifier.c:394 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739 call_netdevice_notifiers_extack net/core/dev.c:1751 [inline] call_netdevice_notifiers net/core/dev.c:1765 [inline] __dev_notify_flags+0x1e9/0x2c0 net/core/dev.c:7607 dev_change_flags+0x10d/0x170 net/core/dev.c:7643 dev_ifsioc+0x2b0/0x940 net/core/dev_ioctl.c:237 dev_ioctl+0x1b8/0xc70 net/core/dev_ioctl.c:488 sock_do_ioctl+0x1bd/0x300 net/socket.c:995 sock_ioctl+0x32b/0x610 net/socket.c:1096 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xd6e/0x1390 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4467c9 Code: e8 0c e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 5b 07 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fdbea222d98 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00000000006dbc58 RCX: 00000000004467c9 RDX: 0000000020000340 RSI: 0000000000008914 RDI: 0000000000000003 RBP: 00000000006dbc50 R08: 00007fdbea223700 R09: 0000000000000000 R10: 00007fdbea223700 R11: 0000000000000246 R12: 00000000006dbc5c R13: 6000030030626669 R14: 0000000000000000 R15: 0000000030626669 Allocated by task 7843: save_stack+0x45/0xd0 mm/kasan/common.c:73 set_track mm/kasan/common.c:85 [inline] __kasan_kmalloc mm/kasan/common.c:495 [inline] __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:468 kasan_kmalloc+0x9/0x10 mm/kasan/common.c:509 kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3615 kmalloc include/linux/slab.h:545 [inline] x25_link_device_up+0x46/0x3f0 net/x25/x25_link.c:249 x25_device_event+0x116/0x2b0 net/x25/af_x25.c:242 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93 __raw_notifier_call_chain kernel/notifier.c:394 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739 call_netdevice_notifiers_extack net/core/dev.c:1751 [inline] call_netdevice_notifiers net/core/dev.c:1765 [inline] __dev_notify_flags+0x121/0x2c0 net/core/dev.c:7605 dev_change_flags+0x10d/0x170 net/core/dev.c:7643 dev_ifsioc+0x2b0/0x940 net/core/dev_ioctl.c:237 dev_ioctl+0x1b8/0xc70 net/core/dev_ioctl.c:488 sock_do_ioctl+0x1bd/0x300 net/socket.c:995 sock_ioctl+0x32b/0x610 net/socket.c:1096 vfs_ioctl fs/ioctl.c:46 [inline] file_ioctl fs/ioctl.c:509 [inline] do_vfs_ioctl+0xd6e/0x1390 fs/ioctl.c:696 ksys_ioctl+0xab/0xd0 fs/ioctl.c:713 __do_sys_ioctl fs/ioctl.c:720 [inline] __se_sys_ioctl fs/ioctl.c:718 [inline] __x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 7865: save_stack+0x45/0xd0 mm/kasan/common.c:73 set_track mm/kasan/common.c:85 [inline] __kasan_slab_free+0x102/0x150 mm/kasan/common.c:457 kasan_slab_free+0xe/0x10 mm/kasan/common.c:465 __cache_free mm/slab.c:3494 [inline] kfree+0xcf/0x230 mm/slab.c:3811 x25_neigh_put include/net/x25.h:253 [inline] x25_connect+0x8d8/0xde0 net/x25/af_x25.c:824 __sys_connect+0x266/0x330 net/socket.c:1685 __do_sys_connect net/socket.c:1696 [inline] __se_sys_connect net/socket.c:1693 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1693 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8880a030edc0 which belongs to the cache kmalloc-256 of size 256 The buggy address is located 16 bytes inside of 256-byte region [ffff8880a030edc0, ffff8880a030eec0) The buggy address belongs to the page: page:ffffea000280c380 count:1 mapcount:0 mapping:ffff88812c3f07c0 index:0x0 flags: 0x1fffc0000000200(slab) raw: 01fffc0000000200 ffffea0002806788 ffffea00027f0188 ffff88812c3f07c0 raw: 0000000000000000 ffff8880a030e000 000000010000000c 0000000000000000 page dumped because: kasan: bad access detected Signed-off-by:
-
Miaohe Lin authored
[ Upstream commit a843dc4e ] In func check_6rd,tunnel->ip6rd.relay_prefixlen may equal to 32,so UBSAN complain about it. UBSAN: Undefined behaviour in net/ipv6/sit.c:781:47 shift exponent 32 is too large for 32-bit type 'unsigned int' CPU: 6 PID: 20036 Comm: syz-executor.0 Not tainted 4.19.27 #2 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xca/0x13e lib/dump_stack.c:113 ubsan_epilogue+0xe/0x81 lib/ubsan.c:159 __ubsan_handle_shift_out_of_bounds+0x293/0x2e8 lib/ubsan.c:425 check_6rd.constprop.9+0x433/0x4e0 net/ipv6/sit.c:781 try_6rd net/ipv6/sit.c:806 [inline] ipip6_tunnel_xmit net/ipv6/sit.c:866 [inline] sit_tunnel_xmit+0x141c/0x2720 net/ipv6/sit.c:1033 __netdev_start_xmit include/linux/netdevice.h:4300 [inline] netdev_start_xmit include/linux/netdevice.h:4309 [inline] xmit_one net/core/dev.c:3243 [inline] dev_hard_start_xmit+0x17c/0x780 net/core/dev.c:3259 __dev_queue_xmit+0x1656/0x2500 net/core/dev.c:3829 neigh_output include/net/neighbour.h:501 [inline] ip6_finish_output2+0xa36/0x2290 net/ipv6/ip6_output.c:120 ip6_finish_output+0x3e7/0xa20 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x1e2/0x720 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0x99/0x170 net/ipv6/output_core.c:176 ip6_send_skb+0x9d/0x2f0 net/ipv6/ip6_output.c:1697 ip6_push_pending_frames+0xc0/0x100 net/ipv6/ip6_output.c:1717 rawv6_push_pending_frames net/ipv6/raw.c:616 [inline] rawv6_sendmsg+0x2435/0x3530 net/ipv6/raw.c:946 inet_sendmsg+0xf8/0x5c0 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg+0xc8/0x110 net/socket.c:631 ___sys_sendmsg+0x6cf/0x890 net/socket.c:2114 __sys_sendmsg+0xf0/0x1b0 net/socket.c:2152 do_syscall_64+0xc8/0x580 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Signed-off-by:
linmiaohe <linmiaohe@huawei.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 1e027960 ] syzbot found another add_timer() issue, this time in net/hsr [1] Let's use mod_timer() which is safe. [1] kernel BUG at kernel/time/timer.c:1136! invalid opcode: 0000 [#1] PREEMPT SMP KASAN CPU: 0 PID: 15909 Comm: syz-executor.3 Not tainted 5.0.0+ #97 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 kobject: 'loop2' (00000000f5629718): kobject_uevent_env RIP: 0010:add_timer kernel/time/timer.c:1136 [inline] RIP: 0010:add_timer+0x654/0xbe0 kernel/time/timer.c:1134 Code: 0f 94 c5 31 ff 44 89 ee e8 09 61 0f 00 45 84 ed 0f 84 77 fd ff ff e8 bb 5f 0f 00 e8 07 10 a0 ff e9 68 fd ff ff e8 ac 5f 0f 00 <0f> 0b e8 a5 5f 0f 00 0f 0b e8 9e 5f 0f 00 4c 89 b5 58 ff ff ff e9 RSP: 0018:ffff8880656eeca0 EFLAGS: 00010246 kobject: 'loop2' (00000000f5629718): fill_kobj_path: path = '/devices/virtual/block/loop2' RAX: 0000000000040000 RBX: 1ffff1100caddd9a RCX: ffffc9000c436000 RDX: 0000000000040000 RSI: ffffffff816056c4 RDI: ffff88806a2f6cc8 RBP: ffff8880656eed58 R08: ffff888067f4a300 R09: ffff888067f4abc8 R10: 0000000000000000 R11: 0000000000000000 R12: ffff88806a2f6cc0 R13: dffffc0000000000 R14: 0000000000000001 R15: ffff8880656eed30 FS: 00007fc2019bf700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000738000 CR3: 0000000067e8e000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: hsr_check_announce net/hsr/hsr_device.c:99 [inline] hsr_check_carrier_and_operstate+0x567/0x6f0 net/hsr/hsr_device.c:120 hsr_netdev_notify+0x297/0xa00 net/hsr/hsr_main.c:51 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93 __raw_notifier_call_chain kernel/notifier.c:394 [inline] raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739 call_netdevice_notifiers_extack net/core/dev.c:1751 [inline] call_netdevice_notifiers net/core/dev.c:1765 [inline] dev_open net/core/dev.c:1436 [inline] dev_open+0x143/0x160 net/core/dev.c:1424 team_port_add drivers/net/team/team.c:1203 [inline] team_add_slave+0xa07/0x15d0 drivers/net/team/team.c:1933 do_set_master net/core/rtnetlink.c:2358 [inline] do_set_master+0x1d4/0x230 net/core/rtnetlink.c:2332 do_setlink+0x966/0x3510 net/core/rtnetlink.c:2493 rtnl_setlink+0x271/0x3b0 net/core/rtnetlink.c:2747 rtnetlink_rcv_msg+0x465/0xb00 net/core/rtnetlink.c:5192 netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485 rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5210 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925 sock_sendmsg_nosec net/socket.c:622 [inline] sock_sendmsg+0xdd/0x130 net/socket.c:632 sock_write_iter+0x27c/0x3e0 net/socket.c:923 call_write_iter include/linux/fs.h:1869 [inline] do_iter_readv_writev+0x5e0/0x8e0 fs/read_write.c:680 do_iter_write fs/read_write.c:956 [inline] do_iter_write+0x184/0x610 fs/read_write.c:937 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1001 do_writev+0xf6/0x290 fs/read_write.c:1036 __do_sys_writev fs/read_write.c:1109 [inline] __se_sys_writev fs/read_write.c:1106 [inline] __x64_sys_writev+0x75/0xb0 fs/read_write.c:1106 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x457f29 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fc2019bec78 EFLAGS: 00000246 ORIG_RAX: 0000000000000014 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457f29 RDX: 0000000000000001 RSI: 00000000200000c0 RDI: 0000000000000003 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc2019bf6d4 R13: 00000000004c4a60 R14: 00000000004dd218 R15: 00000000ffffffff Fixes: f421436a ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by:
-
Mao Wenan authored
[ Upstream commit 6caabe7f ] If hsr_add_port(hsr, hsr_dev, HSR_PT_MASTER) failed to add port, it directly returns res and forgets to free the node that allocated in hsr_create_self_node(), and forgets to delete the node->mac_list linked in hsr->self_node_db. BUG: memory leak unreferenced object 0xffff8881cfa0c780 (size 64): comm "syz-executor.0", pid 2077, jiffies 4294717969 (age 2415.377s) hex dump (first 32 bytes): e0 c7 a0 cf 81 88 ff ff 00 02 00 00 00 00 ad de ................ 00 e6 49 cd 81 88 ff ff c0 9b 87 d0 81 88 ff ff ..I............. backtrace: [<00000000e2ff5070>] hsr_dev_finalize+0x736/0x960 [hsr] [<000000003ed2e597>] hsr_newlink+0x2b2/0x3e0 [hsr] [<000000003fa8c6b6>] __rtnl_newlink+0xf1f/0x1600 net/core/rtnetlink.c:3182 [<000000001247a7ad>] rtnl_newlink+0x66/0x90 net/core/rtnetlink.c:3240 [<00000000e7d1b61d>] rtnetlink_rcv_msg+0x54e/0xb90 net/core/rtnetlink.c:5130 [<000000005556bd3a>] netlink_rcv_skb+0x129/0x340 net/netlink/af_netlink.c:2477 [<00000000741d5ee6>] netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] [<00000000741d5ee6>] netlink_unicast+0x49a/0x650 net/netlink/af_netlink.c:1336 [<000000009d56f9b7>] netlink_sendmsg+0x88b/0xdf0 net/netlink/af_netlink.c:1917 [<0000000046b35c59>] sock_sendmsg_nosec net/socket.c:621 [inline] [<0000000046b35c59>] sock_sendmsg+0xc3/0x100 net/socket.c:631 [<00000000d208adc9>] __sys_sendto+0x33e/0x560 net/socket.c:1786 [<00000000b582837a>] __do_sys_sendto net/socket.c:1798 [inline] [<00000000b582837a>] __se_sys_sendto net/socket.c:1794 [inline] [<00000000b582837a>] __x64_sys_sendto+0xdd/0x1b0 net/socket.c:1794 [<00000000c866801d>] do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 [<00000000fea382d9>] entry_SYSCALL_64_after_hwframe+0x49/0xbe [<00000000e01dacb3>] 0xffffffffffffffff Fixes: c5a75911 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 163d1c3d ] Back in 2013 Hannes took care of most of such leaks in commit bceaa902 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") But the bug in l2tp_ip6_recvmsg() has not been fixed. syzbot report : BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 CPU: 1 PID: 10996 Comm: syz-executor362 Not tainted 5.0.0+ #11 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600 kmsan_internal_check_memory+0x9f4/0xb10 mm/kmsan/kmsan.c:694 kmsan_copy_to_user+0xab/0xc0 mm/kmsan/kmsan_hooks.c:601 _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32 copy_to_user include/linux/uaccess.h:174 [inline] move_addr_to_user+0x311/0x570 net/socket.c:227 ___sys_recvmsg+0xb65/0x1310 net/socket.c:2283 do_recvmmsg+0x646/0x10c0 net/socket.c:2390 __sys_recvmmsg net/socket.c:2469 [inline] __do_sys_recvmmsg net/socket.c:2492 [inline] __se_sys_recvmmsg+0x1d1/0x350 net/socket.c:2485 __x64_sys_recvmmsg+0x62/0x80 net/socket.c:2485 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x445819 Code: e8 6c b6 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 2b 12 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f64453eddb8 EFLAGS: 00000246 ORIG_RAX: 000000000000012b RAX: ffffffffffffffda RBX: 00000000006dac28 RCX: 0000000000445819 RDX: 0000000000000005 RSI: 0000000020002f80 RDI: 0000000000000003 RBP: 00000000006dac20 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006dac2c R13: 00007ffeba8f87af R14: 00007f64453ee9c0 R15: 20c49ba5e353f7cf Local variable description: ----addr@___sys_recvmsg Variable was created at: ___sys_recvmsg+0xf6/0x1310 net/socket.c:2244 do_recvmmsg+0x646/0x10c0 net/socket.c:2390 Bytes 0-31 of 32 are uninitialized Memory access of size 32 starts at ffff8880ae62fbb0 Data copied to user address 0000000020000000 Fixes: a32e0eec ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6") Signed-off-by:
-
Eric Biggers authored
commit 4aa68e07 upstream. When checking for permission to view keys whilst reading from /proc/keys, we should use the credentials with which the /proc/keys file was opened. This is because, in a classic type of exploit, it can be possible to bypass checks for the *current* credentials by passing the file descriptor to a suid program. Following commit 34dbbcdb ("Make file credentials available to the seqfile interfaces") we can finally fix it. So let's do it. Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Zubin Mithra <zsm@chromium.org> Signed-off-by:
-
Erik Schmauss authored
commit 8b23570a upstream. Increase the reference count limit to 0x4000 as the current one is not sufficient for some large server systems. Reviewed-by:
Dimitri Sivanich <dimitri.sivanich@hpe.com> Tested-by:
Russ Anderson <russ.anderson@hpe.com> Reported-by:
Mike Travis <mike.travis@hpe.com> Signed-off-by:
Erik Schmauss <erik.schmauss@intel.com> [ rjw: Changelog ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Frank van der Linden <fllinden@amazon.com> Signed-off-by:
-
- 13 Mar, 2019 30 commits
-
-
Greg Kroah-Hartman authored
-
Peter Zijlstra (Intel) authored
commit 52f64909 upstream Skylake systems will receive a microcode update to address a TSX errata. This microcode will (by default) clobber PMC3 when TSX instructions are (speculatively or not) executed. It also provides an MSR to cause all TSX transaction to abort and preserve PMC3. Add the CPUID enumeration and MSR definition. Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Peter Zijlstra (Intel) authored
commit 11f8b2d6 upstream Such that we can re-use it. Signed-off-by:
-
Peter Zijlstra (Intel) authored
commit d01b1f96 upstream The cpuc data structure allocation is different between fake and real cpuc's; use the same code to init/free both. Signed-off-by:
-
Krzysztof Kozlowski authored
commit 28928a3c upstream. In Odroid XU3 Lite board, the temperature levels reported for thermal zone 0 were weird. In warm room: /sys/class/thermal/thermal_zone0/temp:32000 /sys/class/thermal/thermal_zone1/temp:51000 /sys/class/thermal/thermal_zone2/temp:55000 /sys/class/thermal/thermal_zone3/temp:54000 /sys/class/thermal/thermal_zone4/temp:51000 Sometimes after booting the value was even equal to ambient temperature which is highly unlikely to be a real temperature of sensor in SoC. The thermal sensor's calibration (trimming) is based on fused values. In case of the board above, the fused values are: 35, 52, 43, 58 and 43 (corresponding to each TMU device). However driver defined a minimum value for fused data as 40 and for smaller values it was using a hard-coded 55 instead. This lead to mapping data from sensor to wrong temperatures for thermal zone 0. Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10) do not impose any limits on fused values. Since we do not have any knowledge about these limits, use 0 as a minimum accepted fused value. This should essentially allow accepting any reasonable fused value thus behaving like vendor driver. The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing exynos4412 with one change - the samsung,tmu_min_efuse_value. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Acked-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Acked-by:
Eduardo Valentin <edubezval@gmail.com> Reviewed-by:
Javier Martinez Canillas <javier@osg.samsung.com> Tested-by:
Anand Moon <linux.amoon@gmail.com> Tested-by:
-
Vincent Whitchurch authored
[ Upstream commit afc9f65e ] When building the kernel as Thumb-2 with binutils 2.29 or newer, if the assembler has seen the .type directive (via ENDPROC()) for a symbol, it automatically handles the setting of the lowest bit when the symbol is used with ADR. The badr macro on the other hand handles this lowest bit manually. This leads to a jump to a wrong address in the wrong state in the syscall return path: Internal error: Oops - undefined instruction: 0 [#2] SMP THUMB2 Modules linked in: CPU: 0 PID: 652 Comm: modprobe Tainted: G D 4.18.0-rc3+ #8 PC is at ret_fast_syscall+0x4/0x62 LR is at sys_brk+0x109/0x128 pc : [<80101004>] lr : [<801c8a35>] psr: 60000013 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 50c5387d Table: 9e82006a DAC: 00000051 Process modprobe (pid: 652, stack limit = 0x(ptrval)) 80101000 <ret_fast_syscall>: 80101000: b672 cpsid i 80101002: f8d9 2008 ldr.w r2, [r9, #8] 80101006: f1b2 4ffe cmp.w r2, #2130706432 ; 0x7f000000 80101184 <local_restart>: 80101184: f8d9 a000 ldr.w sl, [r9] 80101188: e92d 0030 stmdb sp!, {r4, r5} 8010118c: f01a 0ff0 tst.w sl, #240 ; 0xf0 80101190: d117 bne.n 801011c2 <__sys_trace> 80101192: 46ba mov sl, r7 80101194: f5ba 7fc8 cmp.w sl, #400 ; 0x190 80101198: bf28 it cs 8010119a: f04f 0a00 movcs.w sl, #0 8010119e: f3af 8014 nop.w {20} 801011a2: f2af 1ea2 subw lr, pc, #418 ; 0x1a2 To fix this, add a new symbol name which doesn't have ENDPROC used on it and use that with badr. We can't remove the badr usage since that would would cause breakage with older binutils. Signed-off-by:
Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Ard Biesheuvel authored
[ Upstream commit e02f5c1b ] The DRM driver stack is designed to work with cache coherent devices only, but permits an optimization to be enabled in some cases, where for some buffers, both the CPU and the GPU use uncached mappings, removing the need for DMA snooping and allocation in the CPU caches. The use of uncached GPU mappings relies on the correct implementation of the PCIe NoSnoop TLP attribute by the platform, otherwise the GPU will use cached mappings nonetheless. On x86 platforms, this does not seem to matter, as uncached CPU mappings will snoop the caches in any case. However, on ARM and arm64, enabling this optimization on a platform where NoSnoop is ignored results in loss of coherency, which breaks correct operation of the device. Since we have no way of detecting whether NoSnoop works or not, just disable this optimization entirely for ARM and arm64. Cc: Christian Koenig <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: David Zhou <David1.Zhou@amd.com> Cc: Huang Rui <ray.huang@amd.com> Cc: Junwei Zhang <Jerry.Zhang@amd.com> Cc: Michel Daenzer <michel.daenzer@amd.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: amd-gfx list <amd-gfx@lists.freedesktop.org> Cc: dri-devel <dri-devel@lists.freedesktop.org> Reported-by:
Carsten Haitzler <Carsten.Haitzler@arm.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.kernel.org/patch/10778815/Signed-off-by:
-
Marek Szyprowski authored
commit a66352e0 upstream. Add minimal parameters needed by the Exynos CLKOUT driver to Exynos3250 PMU node. This fixes the following warning on boot: exynos_clkout_init: failed to register clkout clock Fixes: d19bb397 ("ARM: dts: exynos: Update PMU node with CLKOUT related data") Cc: <stable@vger.kernel.org> Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Marek Szyprowski authored
commit ec33745b upstream. Commit 225da7e6 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common") added MMC power sequence for eMMC card of Odroid X2/U3. It reused generic sd1_cd pin control configuration node and only disabled pull-up. However that time the pinctrl configuration was not applied during MMC power sequence driver initialization. This has been changed later by commit d97a1e5d ("mmc: pwrseq: convert to proper platform device"). It turned out then, that the provided pinctrl configuration is not correct, because the eMMC_RTSN line is being re-configured as 'special function/card detect function for mmc1 controller' not the simple 'output', thus the power sequence driver doesn't really set the pin value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this by providing separate node with eMMC_RTSN pin configuration. Cc: <stable@vger.kernel.org> Reported-by:
Markus Reichl <m.reichl@fivetechno.de> Suggested-by:
Ulf Hansson <ulf.hansson@linaro.org> Fixes: 225da7e6 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common") Signed-off-by:
-
Peter Zijlstra authored
commit 38d589f2 upstream. With the ultimate goal of keeping rt_mutex wait_list and futex_q waiters consistent it's necessary to split 'rt_mutex_futex_lock()' into finer parts, such that only the actual blocking can be done without hb->lock held. Split split_mutex_finish_proxy_lock() into two parts, one that does the blocking and one that does remove_waiter() when the lock acquire failed. When the rtmutex was acquired successfully the waiter can be removed in the acquisiton path safely, since there is no concurrency on the lock owner. This means that, except for futex_lock_pi(), all wait_list modifications are done with both hb->lock and wait_lock held. [bigeasy@linutronix.de: fix for futex_requeue_pi_signal_restart] Signed-off-by:
-
Gustavo A. R. Silva authored
commit 5e420fe6 upstream. Add missing break statement and fix identation issue. This bug was found thanks to the ongoing efforts to enable -Wimplicit-fallthrough. Fixes: 9cb62fa2 ("aacraid: Log firmware AIF messages") Cc: stable@vger.kernel.org Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit df997abe upstream. Add missing break statement in order to prevent the code from falling through to case ISCSI_BOOT_TGT_NAME, which is unnecessary. This bug was found thanks to the ongoing efforts to enable -Wimplicit-fallthrough. Fixes: b33a84a3 ("ibft: convert iscsi_ibft module to iscsi boot lib") Cc: stable@vger.kernel.org Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Vincent Batts authored
commit e154ab69 upstream. Lenovo s21e-20 uses ELAN0601 in its ACPI tables for the Elan touchpad. Signed-off-by:
Vincent Batts <vbatts@hashbangbash.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Jason Gerecke authored
commit 44fc95e2 upstream. Tablet initially begins communicating at 9600 baud, so this command should be used to connect to the device: $ inputattach --daemon --baud 9600 --wacom_iv /dev/ttyS0 https://github.com/linuxwacom/xf86-input-wacom/issues/40Signed-off-by:
Jason Gerecke <jason.gerecke@wacom.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Tetsuo Handa authored
[ Upstream commit 43636c80 ] When something let __find_get_block_slow() hit all_mapped path, it calls printk() for 100+ times per a second. But there is no need to print same message with such high frequency; it is just asking for stall warning, or at least bloating log files. [ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.873324][T15342] b_state=0x00000029, b_size=512 [ 399.878403][T15342] device loop0 blocksize: 4096 [ 399.883296][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.890400][T15342] b_state=0x00000029, b_size=512 [ 399.895595][T15342] device loop0 blocksize: 4096 [ 399.900556][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8 [ 399.907471][T15342] b_state=0x00000029, b_size=512 [ 399.912506][T15342] device loop0 blocksize: 4096 This patch reduces frequency to up to once per a second, in addition to concatenating three lines into one. [ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8, b_state=0x00000029, b_size=512, device loop0 blocksize: 4096 Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Jun-Ru Chang authored
[ Upstream commit 2b424cfc ] Patch (b6c7a324 "MIPS: Fix get_frame_info() handling of microMIPS function size.") introduces additional function size check for microMIPS by only checking insn between ip and ip + func_size. However, func_size in get_frame_info() is always 0 if KALLSYMS is not enabled. This causes get_frame_info() to return immediately without calculating correct frame_size, which in turn causes "Can't analyze schedule() prologue" warning messages at boot time. This patch removes func_size check, and let the frame_size check run up to 128 insns for both MIPS and microMIPS. Signed-off-by:
Jun-Ru Chang <jrjang@realtek.com> Signed-off-by:
Tony Wu <tonywu@realtek.com> Signed-off-by:
Paul Burton <paul.burton@mips.com> Fixes: b6c7a324 ("MIPS: Fix get_frame_info() handling of microMIPS function size.") Cc: <ralf@linux-mips.org> Cc: <jhogan@kernel.org> Cc: <macro@mips.com> Cc: <yamada.masahiro@socionext.com> Cc: <peterz@infradead.org> Cc: <mingo@kernel.org> Cc: <linux-mips@vger.kernel.org> Cc: <linux-kernel@vger.kernel.org> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit 59a17706 ] When perf is built with the annobin plugin (RHEL8 build) extra symbols are added to its binary: # nm perf | grep annobin | head -10 0000000000241100 t .annobin_annotate.c 0000000000326490 t .annobin_annotate.c 0000000000249255 t .annobin_annotate.c_end 00000000003283a8 t .annobin_annotate.c_end 00000000001bce18 t .annobin_annotate.c_end.hot 00000000001bce18 t .annobin_annotate.c_end.hot 00000000001bc3e2 t .annobin_annotate.c_end.unlikely 00000000001bc400 t .annobin_annotate.c_end.unlikely 00000000001bce18 t .annobin_annotate.c.hot 00000000001bce18 t .annobin_annotate.c.hot ... Those symbols have no use for report or annotation and should be skipped. Moreover they interfere with the DWARF unwind test on the PPC arch, where they are mixed with checked symbols and then the test fails: # perf test dwarf -v 59: Test dwarf unwind : --- start --- test child forked, pid 8515 unwind: .annobin_dwarf_unwind.c:ip = 0x10dba40dc (0x2740dc) ... got: .annobin_dwarf_unwind.c 0x10dba40dc, expecting test__arch_unwind_sample unwind: failed with 'no error' The annobin symbols are defined as NOTYPE/LOCAL/HIDDEN: # readelf -s ./perf | grep annobin | head -1 40: 00000000001bce4f 0 NOTYPE LOCAL HIDDEN 13 .annobin_init.c They can still pass the check for the label symbol. Adding check for HIDDEN and INTERNAL (as suggested by Nick below) visibility and filter out such symbols. > Just to be awkward, if you are going to ignore STV_HIDDEN > symbols then you should probably also ignore STV_INTERNAL ones > as well... Annobin does not generate them, but you never know, > one day some other tool might create some. Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Nick Clifton <nickc@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20190128133526.GD15461@kravaSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Julian Wiedmann authored
[ Upstream commit afa0c590 ] The error path in qeth_alloc_qdio_buffers() that takes care of cleaning up the Output Queues is buggy. It first frees the queue, but then calls qeth_clear_outq_buffers() with that very queue struct. Make the call to qeth_clear_outq_buffers() part of the free action (in the correct order), and while at it fix the naming of the helper. Fixes: 0da9581d ("qeth: exploit asynchronous delivery of storage blocks") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by:
Alexandra Winter <wintera@linux.ibm.com> Signed-off-by:
-
Martynas Pumputis authored
[ Upstream commit 4e35c1cb ] It is possible that two concurrent packets originating from the same socket of a connection-less protocol (e.g. UDP) can end up having different IP_CT_DIR_REPLY tuples which results in one of the packets being dropped. To illustrate this, consider the following simplified scenario: 1. Packet A and B are sent at the same time from two different threads by same UDP socket. No matching conntrack entry exists yet. Both packets cause allocation of a new conntrack entry. 2. get_unique_tuple gets called for A. No clashing entry found. conntrack entry for A is added to main conntrack table. 3. get_unique_tuple is called for B and will find that the reply tuple of B is already taken by A. It will allocate a new UDP source port for B to resolve the clash. 4. conntrack entry for B cannot be added to main conntrack table because its ORIGINAL direction is clashing with A and the REPLY directions of A and B are not the same anymore due to UDP source port reallocation done in step 3. This patch modifies nf_conntrack_tuple_taken so it doesn't consider colliding reply tuples if the IP_CT_DIR_ORIGINAL tuples are equal. [ Florian: simplify patch to not use .allow_clash setting and always ignore identical flows ] Signed-off-by:
Martynas Pumputis <martynas@weave.works> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Westphal authored
[ Upstream commit 98bfc341 ] Check basic nat/redirect/masquerade for ipv4 and ipv6. Signed-off-by:
-
Naresh Kamboju authored
[ Upstream commit 952b72f8 ] In selftests the config fragment for netfilter was added as NF_TABLES_INET=y and this patch correct it as CONFIG_NF_TABLES_INET=y Signed-off-by:
Naresh Kamboju <naresh.kamboju@linaro.org> Acked-by:
-
Andy Shevchenko authored
[ Upstream commit 6454368a ] In case of mapping error the DMA addresses are invalid and continuing will screw system memory or potentially something else. [ 222.480310] dmatest: dma0chan7-copy0: summary 1 tests, 3 failures 6 iops 349 KB/s (0) ... [ 240.912725] check: Corrupted low memory at 00000000c7c75ac9 (2940 phys) = 5656000000000000 [ 240.921998] check: Corrupted low memory at 000000005715a1cd (2948 phys) = 279f2aca5595ab2b [ 240.931280] check: Corrupted low memory at 000000002f4024c0 (2950 phys) = 5e5624f349e793cf ... Abort any test if mapping failed. Fixes: 4076e755 ("dmatest: convert to dmaengine_unmap_data") Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Stefano Garzarella authored
[ Upstream commit 85965487 ] When the virtio transport device disappear, we should reset all connected sockets in order to inform the users. Signed-off-by:
Stefano Garzarella <sgarzare@redhat.com> Reviewed-by:
Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by:
-
Stefano Garzarella authored
[ Upstream commit 22b5c0b6 ] virtio_vsock_remove() invokes the vsock_core_exit() also if there are opened sockets for the AF_VSOCK protocol family. In this way the vsock "transport" pointer is set to NULL, triggering the kernel panic at the first socket activity. This patch move the vsock_core_init()/vsock_core_exit() in the virtio_vsock respectively in module_init and module_exit functions, that cannot be invoked until there are open sockets. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1609699Reported-by:
Yan Fu <yafu@redhat.com> Signed-off-by:
-
Codrin Ciubotariu authored
[ Upstream commit dc3f595b ] atchan->status variable is used to store two different information: - pass channel interrupts status from interrupt handler to tasklet; - channel information like whether it is cyclic or paused; This causes a bug when device_terminate_all() is called, (AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when a new descriptor for a cyclic transfer is created, the driver reports the channel as in use: if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) { dev_err(chan2dev(chan), "channel currently used\n"); return NULL; } This patch fixes the bug by adding a different struct member to keep the interrupts status separated from the channel status bits. Fixes: e1f7c9ee ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Signed-off-by:
Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Acked-by:
Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by:
-
Paul Kocialkowski authored
[ Upstream commit b14e945b ] When initializing clocks, a reference to the TCON channel 0 clock is obtained. However, the clock is never prepared and enabled later. Switching from simplefb to DRM actually disables the clock (that was usually configured by U-Boot) because of that. On the V3s, this results in a hang when writing to some mixer registers when switching over to DRM from simplefb. Fix this by preparing and enabling the clock when initializing other clocks. Waiting for sun4i_tcon_channel_enable to enable the clock is apparently too late and results in the same mixer register access hang. Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190131132550.26355-1-paul.kocialkowski@bootlin.comSigned-off-by:
-
Lubomir Rintel authored
[ Upstream commit 2380a22b ] Resetting bit 4 disables the interrupt delivery to the "secure processor" core. This breaks the keyboard on a OLPC XO 1.75 laptop, where the firmware running on the "secure processor" bit-bangs the PS/2 protocol over the GPIO lines. It is not clear what the rest of the bits are and Marvell was unhelpful when asked for documentation. Aside from the SP bit, there are probably priority bits. Leaving the unknown bits as the firmware set them up seems to be a wiser course of action compared to just turning them off. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Acked-by:
Pavel Machek <pavel@ucw.cz> [maz: fixed-up subject and commit message] Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Anders Roxell authored
[ Upstream commit f2105d42 ] Fix link errors when CONFIG_FSL_USB2_OTG is enabled and USB_OTG_FSM is set to module then the following link error occurs. aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_ioctl': drivers/usb/phy/phy-fsl-usb.c:1083: undefined reference to `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:1083:(.text+0x574): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_srp': drivers/usb/phy/phy-fsl-usb.c:674: undefined reference to `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:674:(.text+0x61c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_host': drivers/usb/phy/phy-fsl-usb.c:593: undefined reference to `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:593:(.text+0x7a4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_hnp': drivers/usb/phy/phy-fsl-usb.c:695: undefined reference to `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:695:(.text+0x858): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `a_wait_enum': drivers/usb/phy/phy-fsl-usb.c:274: undefined reference to `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:274:(.text+0x16f0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o:drivers/usb/phy/phy-fsl-usb.c:619: more undefined references to `otg_statemachine' follow aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_peripheral': drivers/usb/phy/phy-fsl-usb.c:619:(.text+0x1fa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine' make[1]: *** [Makefile:1020: vmlinux] Error 1 make[1]: Target 'Image' not remade because of errors. make: *** [Makefile:152: sub-make] Error 2 make: Target 'Image' not remade because of errors. Rework so that FSL_USB2_OTG depends on that the USB_OTG_FSM is builtin. Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Srinivas Kandagatla authored
[ Upstream commit 2a81efb0 ] Add compatible to gicv3 node to enable quirk required to restrict writing to GICR_WAKER register which is restricted on msm8996 SoC in Hypervisor. With this quirk MSM8996 can at least boot out of mainline, which can help community to work with boards based on MSM8996. Without this patch Qualcomm DB820c board reboots on mainline. Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
Andy Gross <andy.gross@linaro.org> Signed-off-by:
-
Peng Hao authored
[ Upstream commit ba16adeb ] devm_ allocated data will be automatically freed. The free of devm_ allocated data is invalid. Fixes: 1c459de1 ("ARM: pxa: ssp: use devm_ functions") Signed-off-by:
Peng Hao <peng.hao2@zte.com.cn> [title's prefix changed] Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
