When chasing a performance issue on ppc64, I noticed tasks
communicating via a pipe would often end up on different nodes.

It turns out SD_WAKE_AFFINE is not set in our node defition. Commit
9fcd18c9 (sched: re-tune balancing) enabled SD_WAKE_AFFINE
in the node definition for x86 and we need a similar change for
ppc64.

I used lmbench lat_ctx and perf bench pipe to verify this fix. Each
benchmark was run 10 times and the average taken.

lmbench lat_ctx:

before:  66565 ops/sec
after:  204700 ops/sec

3.1x faster

perf bench pipe:

before: 5.6570 usecs
after:  1.3470 usecs

4.2x faster
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

(Merge in order to get the PCIe mps/mrss code fixes)

* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
  x86, iommu: Mark DMAR IRQ as non-threaded
  genirq: Make irq_shutdown() symmetric vs. irq_startup again

* 'for-linus' of git://github.com/chrismason/linux:
  Btrfs: only clear the need lookup flag after the dentry is setup
  BTRFS: Fix lseek return value for error
  Btrfs: don't change inode flag of the dest clone file
  Btrfs: don't make a file partly checksummed through file clone
  Btrfs: fix pages truncation in btrfs_ioctl_clone()
  btrfs: fix d_off in the first dirent

When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.

Currently xhci driver handles MSE event in the following ways:

1. When encounter a MSE event, set ep->skip flag, update event ring
   dequeue pointer and return.

2. When encounter the next event on this ep, the driver will run the
   do-while loop, fetch td from ep's td_list to find the td
   corresponding to this event.  All tds missed are marked as short
   transfer(-EXDEV).

The do-while loop will end in two ways:

1. If the td pointed by the event trb is found;

2. If the ep ring's td_list is empty.

However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.

Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop.  During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list.  This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.

To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds.  This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive".  This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.

When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd.  However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.

After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits.  (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted.  Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.

A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up.  That more
complicated fix will be merged next window, and this fix will be
backported to stable.

This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496eb ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.

Fixes these build errors:

  drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
  drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
  drivers/staging/comedi/drivers/ni_labpc.c: At top level:
  drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
  drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats.  So round it down to
something less intrusive.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more.  But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.

Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
Reported-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add a new udbg driver for the PS3 gelic Ehthernet device.

This driver shares only a few stucture and constant definitions with the
gelic Ethernet device driver, so is implemented as a stand-alone driver
with no dependencies on the gelic Ethernet device driver.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Since commit 188917e1, /proc/ppc64 is a
symlink to /proc/powerpc/. That means that creating /proc/ppc64/eeh will
end up with a unaccessible file, that is not listed under /proc/powerpc/
and, then, not listed under /proc/ppc64/.

Creating /proc/powerpc/eeh fixes that problem and maintain the
compatibility intended with the ppc64 symlink.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>	[3.x]

This should fix the following warning:

 LD      arch/powerpc/sysdev/xics/built-in.o
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1310): Section mismatch in
reference from the function .icp_native_init() to the function
.init.text:.icp_native_init_one_node()
The function .icp_native_init() references
the function __init .icp_native_init_one_node().
This is often because .icp_native_init lacks a __init
annotation or the annotation of .icp_native_init_one_node is wrong.

icp_native_init() is only referenced in `arch/powerpc/sysdev/xics/xics-common.c'
by xics_init() which is itself marked with __init.

= not built-tested =
Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

During hotplug CPU add we get the following error:

Unexpected Error (0) returned from configure-connector

ibm,configure-connector returns 0 for configuration complete, so
catch this and avoid the error.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@kernel.org>

	In SMP mode, the kernel would produce call trace when resumed
	from hibernation. The reason is when the function destroy_context
	is called to drop the resuming mm context, the mm->context.active
	is 1 which is wrong and should be zero.
	We pass the current->active_mm as previous mm context to function
	switch_mmu_context to decrease the context.active by 1.

	In UP mode, there is no effect.
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The various port_init_hw methods of ppc4xx_pciex_hwops should have been
marked __init and when I added ppc4xx_pciex_port_reset_sdr(), which is
__init.  This added many section mismatch warnings like:

WARNING: arch/powerpc/sysdev/built-in.o(.text+0x5c68): Section mismatch in reference from the function ppc440spe_pciex_init_port_hw() to the function .init.text:ppc4xx_pciex_port_reset_sdr()
The function ppc440spe_pciex_init_port_hw() references
the function __init ppc4xx_pciex_port_reset_sdr().
This is often because ppc440spe_pciex_init_port_hw lacks a __init
annotation or the annotation of ppc4xx_pciex_port_reset_sdr is wrong.

Trivial patch to silence those warnings.
Reported-By: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>

Yours Tony
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Based on a patch by Michael Ellerman <michael@ellerman.id.au>

Patch was simply forward ported upstream.

Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Based on a patch by Benjamin Herrenschmidt <benh@kernel.crashing.org>

Modernized and slightly modified to not record erros into the nvram
log since we do not have that device driver just yet.

Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Some config selections were applied to the platform (reference board)
when they actuall apply to the chip.
Signed-off-by: Jimi Xenidis <jimix@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

At this point, window has not been stored anywhere, so it has to be freed
before leaving the function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@

x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
     when != if (...) { <+...kfree(x)...+> }
     when any
     when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
               when forall
(
 return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

u64 is used rather than phys_addr_t to keep things simple, as
this is called from assembly code.

Update callers to pass a 64-bit address in r3/r4.  Other unused
register assignments that were once parameters to machine_init
are dropped.

For FSL BookE, look up the physical address of the device tree from the
effective address passed in r3 by the loader.  This is required for
situations where memory does not start at zero (due to AMP or IOMMU-less
virtualization), and thus the IMA doesn't start at zero, and thus the
device tree effective address does not equal the physical address.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Capture more than twice as much text from the printk buffer, and
compress it to fit it in the lnx,oops-log NVRAM partition.  You
can view the compressed text using the new (as of July 20) --unzip
option of the nvram command in the powerpc-utils package.

[BenH: Added select of ZLIB_DEFLATE]
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

There is one place in the MPIC driver that assumes that the cores are numbered
from 0 to n-1.  However, this is not true if the CPUs are not numbered
sequentially.  This can happen on a eight-core SOC where cores two and three
are removed in the device tree.  So instead of blindly looping, we iterate
over the discovered CPUs and use the SMP ID as the index.

This means that we no longer ask the MPIC how many CPUs there are, so
we also delete mpic->num_cpus.

We also catch if the number of CPUs in the SOC exceeds the number that the
MPIC supports.  This should never happen, of course, but it's good to be
sure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Enable hugepages on Freescale BookE processors.  This allows the kernel to
use huge TLB entries to map pages, which can greatly reduce the number of
TLB misses and the amount of TLB thrashing experienced by applications with
large memory footprints.  Care should be taken when using this on FSL
processors, as the number of large TLB entries supported by the core is low
(16-64) on current processors.

The supported set of hugepage sizes include 4m, 16m, 64m, 256m, and 1g.
Page sizes larger than the max zone size are called "gigantic" pages and
must be allocated on the command line (and cannot be deallocated).

This is currently only fully implemented for Freescale 32-bit BookE
processors, but there is some infrastructure in the code for
64-bit BooKE.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This iotype is only used by the legacy_serial code in powerpc, so the
code should live there, rather than be compiled in for every 8250
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-serial@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The new get_required_mask hook name is longer than many of but not all
of the prior ops.  Tidy the struct initializers to align the equal signs
using the local whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Now that the generic code has dma_map_ops set, instead of having a
messy ifdef & if block in the base dma_get_required_mask hook push
the computation into the dma ops.

If the ops fails to set the get_required_mask hook default to the
width of dma_addr_t.

This also corrects ibmbus ibmebus_dma_supported to require a 64
bit mask.  I doubt anything is checking or setting the dma mask on
that bus.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: benh@kernel.crashing.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

If an architecture sets ARCH_HAS_DMA_GET_REQUIRED_MASK and has settable
dma_map_ops, the required mask may change by the ops implementation.
For example, a system that always has an mmu inline may only require 32
bits while a swiotlb would desire bits to cover all of memory.

Therefore add the field if the architecture does not use the generic
definition of dma_get_required_mask. The first use will by by powerpc.
Note that this does add some dependency on the order in which files are
visible here.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>

* 'slab/urgent' of git://github.com/penberg/linux:
  slub: add slab with one free object to partial list tail

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
  drm/radeon/kms: fix typo in r100_blit_copy
  drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
  drm/radeon: Don't read from CP ring write pointer registers.
  drm/ttm: request zeroed system memory pages for new TT buffer objects

* git://github.com/davem330/net:
  tcp: fix validation of D-SACK
  tcp: fix build error if !CONFIG_SYN_COOKIES

D-SACK is allowed to reside below snd_una. But the corresponding check
in tcp_is_sackblock_valid() is the exact opposite. It looks like a typo.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 946cedcc (tcp: Change possible SYN flooding messages)
added a build error if CONFIG_SYN_COOKIES=n
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
  mfd: Fix omap-usb-host build failure
  mfd: Make omap-usb-host TLL mode work again
  mfd: Set MAX8997 irq pointer
  mfd: Fix initialisation of tps65910 interrupts
  mfd: Check for twl4030-madc NULL pointer
  mfd: Copy the device pointer to the twl4030-madc structure
  mfd: Rename wm8350 static gpio_set_debounce()
  mfd: Fix value of WM8994_CONFIGURE_GPIO

The BO blit code inconsistenly handled the page size.  This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well.  Switch the driver blit callbacks to take num pages in GPU
page units.

Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.

v2: incorporate suggestions from Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

cur_pages is the number of pages per loop iteration.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

* git://github.com/davem330/net: (62 commits)
  ipv6: don't use inetpeer to store metrics for routes.
  can: ti_hecc: include linux/io.h
  IRDA: Fix global type conflicts in net/irda/irsysctl.c v2
  net: Handle different key sizes between address families in flow cache
  net: Align AF-specific flowi structs to long
  ipv4: Fix fib_info->fib_metrics leak
  caif: fix a potential NULL dereference
  sctp: deal with multiple COOKIE_ECHO chunks
  ibmveth: Fix checksum offload failure handling
  ibmveth: Checksum offload is always disabled
  ibmveth: Fix issue with DMA mapping failure
  ibmveth: Fix DMA unmap error
  pch_gbe: support ML7831 IOH
  pch_gbe: added the process of FIFO over run error
  pch_gbe: fixed the issue which receives an unnecessary packet.
  sfc: Use 64-bit writes for TX push where possible
  Revert "sfc: Use write-combining to reduce TX latency" and follow-ups
  bnx2x: Fix ethtool advertisement
  bnx2x: Fix 578xx link LED
  bnx2x: Fix XMAC loopback test
  ...

We can race with readdir and the RCU path walking stuff.  This is because we
clear the need lookup flag before actually instantiating the inode.  This will
lead the RCU path walk stuff to find a dentry it thinks is valid without a
d_inode attached.  So instead unhash the dentry when we first start the lookup,
and then clear the flag after we've instantiated the dentry so we're garunteed
to either try the slow lookup, or have the d_inode set properly.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

The recent reworking of btrfs' lseek lead to incorrect
values being returned.  This adds checks for seeking
beyond EOF in SEEK_HOLE and makes sure the error
values come back correct.

Andi Kleen also sent in similar patches.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>