The ct entry object is accessed by the ct add, del, stats and restore
methods. In addition, it is referenced from several hash tables.

The lifetime of the ct entry object was not managed which triggered race
conditions as in the following kasan dump:
[ 3374.973945] ==================================================================
[ 3374.988552] BUG: KASAN: use-after-free in memcmp+0x4c/0x98
[ 3374.999590] Read of size 1 at addr ffff00036129ea55 by task ksoftirqd/1/15
[ 3375.016415] CPU: 1 PID: 15 Comm: ksoftirqd/1 Tainted: G           O      5.4.31+ #1
[ 3375.055301] Call trace:
[ 3375.060214]  dump_backtrace+0x0/0x238
[ 3375.067580]  show_stack+0x24/0x30
[ 3375.074244]  dump_stack+0xe0/0x118
[ 3375.081085]  print_address_description.isra.9+0x74/0x3d0
[ 3375.091771]  __kasan_report+0x198/0x1e8
[ 3375.099486]  kasan_report+0xc/0x18
[ 3375.106324]  __asan_load1+0x60/0x68
[ 3375.113338]  memcmp+0x4c/0x98
[ 3375.119409]  mlx5e_tc_ct_restore_flow+0x3a4/0x6f8 [mlx5_core]
[ 3375.131073]  mlx5e_rep_tc_update_skb+0x1d4/0x2f0 [mlx5_core]
[ 3375.142553]  mlx5e_handle_rx_cqe_rep+0x198/0x308 [mlx5_core]
[ 3375.154034]  mlx5e_poll_rx_cq+0x2a0/0x1060 [mlx5_core]
[ 3375.164459]  mlx5e_napi_poll+0x1d4/0xa78 [mlx5_core]
[ 3375.174453]  net_rx_action+0x28c/0x7a8
[ 3375.182004]  __do_softirq+0x1b4/0x5d0

Manage the lifetime of the ct entry object by using synchornization
mechanisms for concurrent access.

Fixes: ac991b48 ("net/mlx5e: CT: Offload established flows")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Devlink reload can't be allowed on lag devices since reloading one lag
device will cause traffic on the bond to get stucked.
Users who wish to reload a lag device, need to remove the device from
the bond, and only then reload it.

Fixes: 4383cfcc ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In lag mode, setting roce enabled/disable of lag device have no effect.
e.g.: bond device (roce/vf_lag) roce status remain unchanged.
Therefore disable it and add an error message.

Fixes: cc9defcb ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In dual port mode, setting roce enabled/disable for the slave device
have no effect. e.g.: the slave device roce status remain unchanged.
Therefore disable it and add an error message.
Enable or disable roce of the master device affect both master and slave
devices.

Fixes: cc9defcb ("net/mlx5: Handle "enable_roce" devlink param")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Devlink reload can't be allowed on a multi port slave device, because
reload of slave device doesn't take effect.

The right flow is to disable devlink reload for multi port slave
device. Hence, disabling it in mlx5_core probing.

Fixes: 4383cfcc ("net/mlx5: Add devlink reload")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

wait_for_resync is unreliable - if it timeouts, priv_rx will be freed
anyway. However, mlx5e_ktls_handle_get_psv_completion will be called
sooner or later, leading to use-after-free. For example, it can happen
if a CQ error happened, and ICOSQ stopped, but later on the queues are
destroyed, and ICOSQ is flushed with mlx5e_free_icosq_descs.

This patch converts the lifecycle of priv_rx to fully refcount-based, so
that the struct won't be freed before the refcount goes to zero.

Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The commit mentioned below has split the parameters of ICOSQ and async
ICOSQ, but it contained a typo: the CQ parameters were swapped for ICOSQ
and async ICOSQ. Async ICOSQ is longer than the normal ICOSQ, and the CQ
size must be the same as the size of the corresponding SQ, but due to
this bug, the CQ of async ICOSQ was much shorter than async ICOSQ
itself. It led to overflows of the CQ with such messages in dmesg, in
particular, when running multiple kTLS-offloaded streams:

mlx5_core 0000:08:00.0: cq_err_event_notifier:529:(pid 9422): CQ error
on CQN 0x406, syndrome 0x1
mlx5_core 0000:08:00.0 eth2: mlx5e_cq_error_event: cqn=0x000406
event=0x04

This commit fixes the issue by using the corresponding parameters for
ICOSQ and async ICOSQ.

Fixes: c293ac92 ("net/mlx5e: Refactor build channel params")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The commit cited below switched from using napi_synchronize to
synchronize_rcu to have a guarantee that it will finish in finite time.
However, on average, synchronize_rcu takes more time than
napi_synchronize. Given that it's called multiple times per channel on
deactivation, it accumulates to a significant amount, which causes
timeouts in some applications (for example, when using bonding with
NetworkManager).

This commit replaces synchronize_rcu with synchronize_net, which is
faster when called under rtnl_lock, allowing to speed up the described
flow.

Fixes: 9c25a22d ("net/mlx5e: Use synchronize_rcu to sync with NAPI")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, when we discover a fatal error, we are queueing a work that
will wait for a lock in order to enter the device to error state.
Meanwhile, FW commands are still being processed, and gets timeouts.
This can block the driver for few minutes before the work will manage
to get the lock and enter to error state.

Setting the device to error state before queueing health work, in order
to avoid FW commands being processed while the work is waiting for the
lock.

Fixes: c1d4d2e9 ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

struct mlx5e_params contains fields ({rx,tx}_cq_moderation) that depend
on two things: whether DIM is enabled and the state of a private flag
(MLX5E_PFLAG_{RX,TX}_CQE_BASED_MODER). Whenever the DIM state changes,
mlx5e_reset_{rx,tx}_moderation is called to update the fields, however,
only if the channels are open. The flow where the channels are closed
misses the required update of the fields. This commit moves the calls of
mlx5e_reset_{rx,tx}_moderation, so that they run in both flows.

Fixes: ebeaf084 ("net/mlx5e: Properly set default values when disabling adaptive moderation")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When mlx5e_ethtool_set_coalesce doesn't change DIM state
(enabled/disabled), it calls mlx5e_set_priv_channels_coalesce
unconditionally, which in turn invokes a firmware command to set
interrupt moderation parameters. It shouldn't happen while DIM manages
those parameters dynamically (it might even be happening at the same
time).

This patch fixes it by splitting mlx5e_set_priv_channels_coalesce into
two functions (for RX and TX) and calling them only when DIM is disabled
(for RX and TX respectively).

Fixes: cb3c7fd4 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which
does not support XDP, for Connect-X this is no longer true.

Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks XDP for all
future Connect-X devices for all flows even if IPsec offload is not
used.

Fixes: 2d64663c ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

This limitation was inherited by previous Innova (FPGA) IPsec
implementation, it uses its private set of RQ handlers which does
not support striding rq, for Connect-X this is no longer true.

Fix by keeping this limitation only for Innova IPsec supporting devices,
as otherwise this limitation effectively wrongly blocks striding RQs for
all future Connect-X devices for all flows even if IPsec offload is not
used.

Fixes: 2d64663c ("net/mlx5: IPsec: Add HW crypto offload support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

rate_bytes_ps is a 64-bit field. It passed as 32-bit field to
apply_police_params(). Due to this when police rate is higher
than 4Gbps, 32-bit calculation ignores the carry. This results
in incorrect rate configurationn the device.

Fix it by performing 64-bit calculation.

Fixes: fcb64c0f ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Mat Martineau says:

====================
mptcp: Miscellaneous fixes

Here are some MPTCP fixes for the -net tree, addressing various issues
we have seen thanks to syzkaller and other testing:

Patch 1 correctly propagates errors at connection time and for TCP
fallback connections.

Patch 2 sets the expected poll() events on SEND_SHUTDOWN.

Patch 3 fixes a retranmit crash and unneeded retransmissions.

Patch 4 fixes possible uninitialized data on the error path during
socket creation.

Patch 5 addresses a problem with MPTCP window updates.

Patch 6 fixes a case where MPTCP retransmission can get stuck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we do not schedule the MPTCP retransmission
timer after pushing the data when such action happens
in the subflow context.

This may cause hang-up on active-backup scenarios, or
even when only single subflow msks are involved, if we lost
some peer's ack.

Fixes: 6e628cd3 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move mptcp_cleanup_rbuf() related checks inside the mentioned
helper and extend them to mirror TCP checks more closely.

Additionally drop the 'rmem_pending' hack, since commit 87952603
("mptcp: protect the rx path with the msk socket spinlock") we
can use instead 'rmem_released'.

Fixes: ea4ca586 ("mptcp: refine MPTCP-level ack scheduling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mptcp subflow route_req() callback performs the subflow
req initialization after the route_req() check. If the latter
fails, mptcp-specific bits of the current request sockets
are left uninitialized.

The above causes bad things at req socket disposal time, when
the mptcp resources are cleared.

This change addresses the issue by splitting subflow_init_req()
into the actual initialization and the mptcp-specific checks.
The initialization is moved before any possibly failing check.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 7ea851d1 ("tcp: merge 'init_req' and 'route_req' functions")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller was able to trigger the following splat again:

WARNING: CPU: 1 PID: 12512 at net/mptcp/protocol.c:761 mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Modules linked in:
CPU: 1 PID: 12512 Comm: kworker/1:6 Not tainted 5.10.0-rc6 #52
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: events mptcp_worker
RIP: 0010:mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Code: e8 4b 0c ad ff e8 56 21 88 fe 48 b8 00 00 00 00 00 fc ff df 48 c7 04 03 00 00 00 00 48 83 c4 40 5b 5d 41 5c c3 e8 36 21 88 fe <0f> 0b 41 bc c8 00 00 00 eb 98 e8 e7 b1 af fe e9 30 ff ff ff 48 c7
RSP: 0018:ffffc900018c7c68 EFLAGS: 00010293
RAX: ffff888108cb1c80 RBX: 1ffff92000318f8d RCX: ffffffff82ad0307
RDX: 0000000000000000 RSI: ffffffff82ad036a RDI: 0000000000000007
RBP: ffff888113e2d000 R08: ffff888108cb1c80 R09: ffffed10227c5ab7
R10: ffff888113e2d5b7 R11: ffffed10227c5ab6 R12: 0000000000000000
R13: ffff88801f100000 R14: ffff888113e2d5b0 R15: 0000000000000001
FS:  0000000000000000(0000) GS:ffff88811b500000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd76a874ef8 CR3: 000000001689c005 CR4: 0000000000170ee0
Call Trace:
 mptcp_worker+0xaa4/0x1560 net/mptcp/protocol.c:2334
 process_one_work+0x8d3/0x1200 kernel/workqueue.c:2272
 worker_thread+0x9c/0x1090 kernel/workqueue.c:2418
 kthread+0x303/0x410 kernel/kthread.c:292
 ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:296

The mptcp_worker tries to update the MPTCP retransmission timer
even if such timer is not currently scheduled.

The mptcp_rtx_head() return value is bogus: we can have enqueued
data not yet transmitted. The above may additionally cause spurious,
unneeded MPTCP-level retransmissions.

Fix the issue adding an explicit clearing of the rtx queue before
trying to retransmit and checking for unacked data.
Additionally drop an unneeded timer stop call and the unused
mptcp_rtx_tail() helper.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 6e628cd3 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current mptcp_poll() implementation gives unexpected
results after shutdown(SEND_SHUTDOWN) and when the msk
status is TCP_CLOSE.

Set the correct mask.

Fixes: 8edf0864 ("mptcp: rework poll+nospace handling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently all errors received on msk subflows are ignored.
We need to catch at least the errors on connect() and
on fallback sockets.

Use a custom sk_error_report callback at subflow level,
and do the real action under the msk socket lock - via
the usual sock_owned_by_user()/release_callback() schema.

Fixes: 6e628cd3 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu reported that on his system S2R cuts off power to the PHY and
after resuming certain PHY settings are lost. The PM folks confirmed
that cutting off power to selected components in S2R is a valid case.
Therefore resuming from S2R, same as from hibernation, has to assume
that the PHY has power-on defaults. As a consequence use the restore
callback also as resume callback.
In addition make sure that the interrupt configuration is restored.
Let's do this in phy_init_hw() and ensure that after this call
actual interrupt configuration is in sync with phydev->interrupts.
Currently, if interrupt was enabled before hibernation, we would
resume with interrupt disabled because that's the power-on default.

This fix applies cleanly only after the commit marked as fixed.

I don't have an affected system, therefore change is compile-tested
only.

[0] https://lore.kernel.org/netdev/1610120754-14331-1-git-send-email-claudiu.beznea@microchip.com/

Fixes: 611d779a ("net: phy: fix MDIO bus PM PHY resuming")
Reported-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If xdp_do_redirect() fails, the calling driver should handle recycling
or freeing of the page associated with the frame. The dpaa2-eth driver
didn't do either of them and just incremented a counter.
Fix this by trying to DMA map back the page and recycle it or, if the
mapping fails, just free it.

Fixes: d678be1d ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FSL_ENETC_MDIO use symbols from PHYLIB (MDIO_BUS) and MDIO_DEVRES,
however there are no dependency specified in Kconfig

ERROR: modpost: "__mdiobus_register" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "mdiobus_unregister" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!
ERROR: modpost: "devm_mdiobus_alloc_size" [drivers/net/ethernet/freescale/enetc/fsl-enetc-mdio.ko] undefined!

add depends on MDIO_DEVRES && MDIO_BUS
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.

An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.

In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 2 bug fixes.

Two unrelated fixes.  The first one fixes intermittent false TX timeouts
during ring reconfigurations.  The second one fixes a formatting
discrepancy between the stored and the running FW versions.

Please also queue these for -stable.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The running fw.psid version is in decimal format but the stored
fw.psid is in hex format.  This can mislead the user to reset the
NIC to activate the stored version to become the running version.

Fix it to display the stored fw.psid in decimal format.

Fixes: 1388875b ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up.  Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If set_link_state() fails for any reason, we still cleanup the adapter
state and cannot recover from a partial close anyway. So set the adapter
to CLOSED state. That way if a new soft/hard reset is processed, the
adapter will remain in the CLOSED state until the next ibmvnic_open().

Fixes: 01d9bd79 ("ibmvnic: Reorganize device close")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_rmem[1] has been changed to 131072, we should update the documentation
to reflect this.

Fixes: a337531b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Zhibin Liu <zhibinliu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Point out where patchwork bot's code lives, and that we don't want
people posting stuff that doesn't build.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reject the unsupported and invalid ct_state flags of cls flower rules.

Fixes: e0ace68a ("net/sched: cls_flower: Add matching on conntrack info")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull power management fixes from Rafael Wysocki:
 "Address a performance regression related to scale-invariance on x86
  that may prevent turbo CPU frequencies from being used in certain
  workloads on systems using acpi-cpufreq as the CPU performance scaling
  driver and schedutil as the scaling governor"

* tag 'pm-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: ACPI: Update arch scale-invariance max perf ratio if CPPC is not there
  cpufreq: ACPI: Extend frequency tables to cover boost frequencies

Pull ACPI fix from Rafael Wysocki:
 "Revert a problematic ACPICA commit that changed the code to attempt to
  update memory regions which may be read-only on some systems (Ard
  Biesheuvel)"

* tag 'acpi-5.11-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPICA: Interpreter: fix memory leak by using existing buffer"

Pull dmaengine fixes from Vinod Koul:
 "Some late fixes for dmaengine:

  Core:
   - fix channel device_node deletion

  Driver fixes:
   - dw: revert of runtime pm enabling
   - idxd: device state fix, interrupt completion and list corruption
   - ti: resource leak

* tag 'dmaengine-fix2-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
  dmaengine dw: Revert "dmaengine: dw: Enable runtime PM"
  dmaengine: idxd: check device state before issue command
  dmaengine: ti: k3-udma: Fix a resource leak in an error handling path
  dmaengine: move channel device_node deletion to driver
  dmaengine: idxd: fix misc interrupt completion
  dmaengine: idxd: Fix list corruption in description completion

Pull networking fixes from David Miller:
 "Another pile of networing fixes:

   1) ath9k build error fix from Arnd Bergmann

   2) dma memory leak fix in mediatec driver from Lorenzo Bianconi.

   3) bpf int3 kprobe fix from Alexei Starovoitov.

   4) bpf stackmap integer overflow fix from Bui Quang Minh.

   5) Add usb device ids for Cinterion MV31 to qmi_qwwan driver, from
      Christoph Schemmel.

   6) Don't update deleted entry in xt_recent netfilter module, from
      Jazsef Kadlecsik.

   7) Use after free in nftables, fix from Pablo Neira Ayuso.

   8) Header checksum fix in flowtable from Sven Auhagen.

   9) Validate user controlled length in qrtr code, from Sabyrzhan
      Tasbolatov.

  10) Fix race in xen/netback, from Juergen Gross,

  11) New device ID in cxgb4, from Raju Rangoju.

  12) Fix ring locking in rxrpc release call, from David Howells.

  13) Don't return LAPB error codes from x25_open(), from Xie He.

  14) Missing error returns in gsi_channel_setup() from Alex Elder.

  15) Get skb_copy_and_csum_datagram working properly with odd segment
      sizes, from Willem de Bruijn.

  16) Missing RFS/RSS table init in enetc driver, from Vladimir Oltean.

  17) Do teardown on probe failure in DSA, from Vladimir Oltean.

  18) Fix compilation failures of txtimestamp selftest, from Vadim
      Fedorenko.

  19) Limit rx per-napi gro queue size to fix latency regression, from
      Eric Dumazet.

  20) dpaa_eth xdp fixes from Camelia Groza.

  21) Missing txq mode update when switching CBS off, in stmmac driver,
      from Mohammad Athari Bin Ismail.

  22) Failover pending logic fix in ibmvnic driver, from Sukadev
      Bhattiprolu.

  23) Null deref fix in vmw_vsock, from Norbert Slusarek.

  24) Missing verdict update in xdp paths of ena driver, from Shay
      Agroskin.

  25) seq_file iteration fix in sctp from Neil Brown.

  26) bpf 32-bit src register truncation fix on div/mod, from Daniel
      Borkmann.

  27) Fix jmp32 pruning in bpf verifier, from Daniel Borkmann.

  28) Fix locking in vsock_shutdown(), from Stefano Garzarella.

  29) Various missing index bound checks in hns3 driver, from Yufeng Mo.

  30) Flush ports on .phylink_mac_link_down() in dsa felix driver, from
      Vladimir Oltean.

  31) Don't mix up stp and mrp port states in bridge layer, from Horatiu
      Vultur.

  32) Fix locking during netif_tx_disable(), from Edwin Peer"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
  bpf: Fix 32 bit src register truncation on div/mod
  bpf: Fix verifier jmp32 pruning decision logic
  bpf: Fix verifier jsgt branch analysis on max bound
  vsock: fix locking in vsock_shutdown()
  net: hns3: add a check for index in hclge_get_rss_key()
  net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
  net: hns3: add a check for queue_id in hclge_reset_vf_queue()
  net: dsa: felix: implement port flushing on .phylink_mac_link_down
  switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
  bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
  net: watchdog: hold device global xmit lock during tx disable
  netfilter: nftables: relax check for stateful expressions in set definition
  netfilter: conntrack: skip identical origin tuple in same zone only
  vsock/virtio: update credit only if socket is not closed
  net: fix iteration for sctp transport seq_files
  net: ena: Update XDP verdict upon failure
  net/vmw_vsock: improve locking in vsock_connect_timeout()
  net/vmw_vsock: fix NULL pointer dereference
  ibmvnic: Clear failover_pending if unable to schedule
  net: stmmac: set TxQ mode back to DCB after disabling CBS
  ...

Merge misc fixes from Andrew Morton:
 "14 patches.

  Subsystems affected by this patch series: mm (kasan, mremap, tmpfs,
  selftests, memcg, and slub), MAINTAINERS, squashfs, nilfs2, and
  firmware"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  nilfs2: make splice write available again
  mm, slub: better heuristic for number of cpus when calculating slab order
  Revert "mm: memcontrol: avoid workload stalls when lowering memory.high"
  MAINTAINERS: update Andrey Ryabinin's email address
  selftests/vm: rename file run_vmtests to run_vmtests.sh
  tmpfs: disallow CONFIG_TMPFS_INODE64 on alpha
  tmpfs: disallow CONFIG_TMPFS_INODE64 on s390
  mm/mremap: fix BUILD_BUG_ON() error in get_extent
  firmware_loader: align .builtin_fw to 8
  kasan: fix stack traces dependency for HW_TAGS
  squashfs: add more sanity checks in xattr id lookup
  squashfs: add more sanity checks in inode lookup
  squashfs: add more sanity checks in id lookup
  squashfs: avoid out of bounds writes in decompressors

Since 5.10, splice() or sendfile() to NILFS2 return EINVAL.  This was
caused by commit 36e2c742 ("fs: don't allow splice read/write
without explicit ops").

This patch initializes the splice_write field in file_operations, like
most file systems do, to restore the functionality.

Link: https://lkml.kernel.org/r/1612784101-14353-1-git-send-email-konishi.ryusuke@gmail.comSigned-off-by: Joachim Henke <joachim.henke@t-systems.com>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>	[5.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When creating a new kmem cache, SLUB determines how large the slab pages
will based on number of inputs, including the number of CPUs in the
system.  Larger slab pages mean that more objects can be allocated/free
from per-cpu slabs before accessing shared structures, but also
potentially more memory can be wasted due to low slab usage and
fragmentation.  The rough idea of using number of CPUs is that larger
systems will be more likely to benefit from reduced contention, and also
should have enough memory to spare.

Number of CPUs used to be determined as nr_cpu_ids, which is number of
possible cpus, but on some systems many will never be onlined, thus
commit 045ab8c9 ("mm/slub: let number of online CPUs determine the
slub page order") changed it to nr_online_cpus().  However, for kmem
caches created early before CPUs are onlined, this may lead to
permamently low slab page sizes.

Vincent reports a regression [1] of hackbench on arm64 systems:

  "I'm facing significant performances regression on a large arm64
   server system (224 CPUs). Regressions is also present on small arm64
   system (8 CPUs) but in a far smaller order of magnitude

   On 224 CPUs system : 9 iterations of hackbench -l 16000 -g 16
   v5.11-rc4 : 9.135sec (+/- 0.45%)
   v5.11-rc4 + revert this patch: 3.173sec (+/- 0.48%)
   v5.10: 3.136sec (+/- 0.40%)"

Mel reports a regression [2] of hackbench on x86_64, with lockstat suggesting
page allocator contention:

  "i.e. the patch incurs a 7% to 32% performance penalty. This bisected
   cleanly yesterday when I was looking for the regression and then
   found the thread.

   Numerous caches change size. For example, kmalloc-512 goes from
   order-0 (vanilla) to order-2 with the revert.

   So mostly this is down to the number of times SLUB calls into the
   page allocator which only caches order-0 pages on a per-cpu basis"

Clearly num_online_cpus() doesn't work too early in bootup.  We could
change the order dynamically in a memory hotplug callback, but runtime
order changing for existing kmem caches has been already shown as
dangerous, and removed in 32a6f409 ("mm, slub: remove runtime
allocation order changes").

It could be resurrected in a safe manner with some effort, but to fix
the regression we need something simpler.

We could use num_present_cpus() that should be the number of physically
present CPUs even before they are onlined.  That would work for PowerPC
[3], which triggered the original commit, but that still doesn't work on
arm64 [4] as explained in [5].

So this patch tries to determine the best available value without
specific arch knowledge.

 - num_present_cpus() if the number is larger than 1, as that means the
   arch is likely setting it properly

 - nr_cpu_ids otherwise

This should fix the reported regressions while also keeping the effect
of 045ab8c9 for PowerPC systems.  It's possible there are
configurations where num_present_cpus() is 1 during boot while
nr_cpu_ids is at the same time bloated, so these (if they exist) would
keep the large orders based on nr_cpu_ids as was before 045ab8c9.

[1] https://lore.kernel.org/linux-mm/CAKfTPtA_JgMf_+zdFbcb_V9rM7JBWNPjAz9irgwFj7Rou=xzZg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mm/20210128134512.GF3592@techsingularity.net/
[3] https://lore.kernel.org/linux-mm/20210123051607.GC2587010@in.ibm.com/
[4] https://lore.kernel.org/linux-mm/CAKfTPtAjyVmS5VYvU6DBxg4-JEo5bdmWbngf-03YsY18cmWv_g@mail.gmail.com/
[5] https://lore.kernel.org/linux-mm/20210126230305.GD30941@willie-the-truck/

Link: https://lkml.kernel.org/r/20210208134108.22286-1-vbabka@suse.cz
Fixes: 045ab8c9 ("mm/slub: let number of online CPUs determine the slub page order")
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Vincent Guittot <vincent.guittot@linaro.org>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Mel Gorman <mgorman@techsingularity.net>
Tested-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Jann Horn <jannh@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Daniel Borkmann says:

====================
pull-request: bpf 2021-02-10

The following pull-request contains BPF updates for your *net* tree.

We've added 5 non-merge commits during the last 8 day(s) which contain
a total of 3 files changed, 22 insertions(+), 21 deletions(-).

The main changes are:

1) Fix missed execution of kprobes BPF progs when kprobe is firing via
   int3, from Alexei Starovoitov.

2) Fix potential integer overflow in map max_entries for stackmap on
   32 bit archs, from Bui Quang Minh.

3) Fix a verifier pruning and a insn rewrite issue related to 32 bit ops,
   from Daniel Borkmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
c# Please enter a commit message to explain why this merge is necessary,