Merge remote-tracking branches 'regulator/topic/qcom-spmi', 'regulator/topic/rn5t618', 'regulator/topic/tps65218' and 'regulator/topic/twl' into regulator-next

Merge remote-tracking branches 'regulator/topic/mt6397', 'regulator/topic/of', 'regulator/topic/pfuze100', 'regulator/topic/pwm' and 'regulator/topic/qcom-smd' into regulator-next

Merge remote-tracking branches 'regulator/topic/fixed', 'regulator/topic/headers', 'regulator/topic/lp837x', 'regulator/topic/max8973' and 'regulator/topic/mt6323' into regulator-next

Merge remote-tracking branches 'regulator/topic/act8865', 'regulator/topic/can-change-voltage', 'regulator/topic/da9210' and 'regulator/topic/da9211' into regulator-next

Merge remote-tracking branches 'regulator/fix/da9053' and 'regulator/fix/s2mps11' into regulator-linus

This fix alters the minimum and maximum BUCK voltage limits for DA9052 and
DA9053. It does so for the following cases:

DA9052
- BUCK3 (MEM)
   min: 0.925V -> 0.950V
   max: 2.500V -> 2.525V

DA9053
- BUCK3 (MEM)
   min: 0.925V -> 0.950V
   max: 2.500V -> 2.525V
- BUCK4 (PERI)
   min: 0.925V -> 0.950V
   max: 2.500V -> 2.525V

The voltage range remains the same, but the limits are shifted by +0.025V.

This change is provided on DA9052:MEM, DA9053:MEM and DA9053:PERI
and is a voltage difference of 0.025V, compared to those measured before
this fix is applied. The patch has the effect of decreasing *all* measured
voltages on those BUCKs when compared against the previously measured
values for the same software voltage request.

For example, with this fix applied for DA9052:MEM, DA9053:MEM and
DA9053:PERI, the following is true.

Because the previous software defined slot 0 as being 0.925V, if a request
for 0.950V was previously sent, the slot 1 voltage would have been used.
This would have corresponded to an actual measured voltage of 0.975V. But,
with this patch fix, and with slot 0 properly aligned to 0.950V, if a
voltage of 0.950V is requested by software, a measured value of 0.950V will
be provided.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The MT6323 is a regulator found on boards based on MediaTek MT7623 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: John Crispin <john@phrozen.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

Addition of device tree support for DA9210.
Two files are modified, the driver source file and the binding document.

Updates for the regulator source file include an .of_match_table entry and
node match checking in the probe() function for a compatible da9210 string.

Minor binding documentation changes have been made to the title and the
example.
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This node pointer is returned by of_get_child_by_name() with
refcount incremented in this function. of_node_put() is missing
when exitting this function while invalid device type. Fix it
by move of_get_child_by_name() code after device type check.

Found by Coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>

The pm8x41_hfsmps ranges overlap. The first range is from 375000
to 1562500:

 375000 + (95 * 12500) == 1562500

and the second range starts at 1550000. Interestingly, the second
range ends at the correct value when it's set to be the
appropriate start value, 1575000:

 1575000 + ((158 - 96) * 25000) == 3125000
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).

Fixes: 51af2067 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>

The well-spotted fallocate undo fix is good in most cases, but not when
fallocate failed on the very first page.  index 0 then passes lend -1
to shmem_undo_range(), and that has two bad effects: (a) that it will
undo every fallocation throughout the file, unrestricted by the current
range; but more importantly (b) it can cause the undo to hang, because
lend -1 is treated as truncation, which makes it keep on retrying until
every page has gone, but those already fully instantiated will never go
away.  Big thank you to xfstests generic/269 which demonstrates this.

Fixes: b9b4bb26 ("tmpfs: don't undo fallocate past its last page")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull MIPS fix from Ralf Baechle:
 "Another week with just a single 4.7 fix.

  This fixes a possible 'loss' of the huge page bit from pmd on
  permission change"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix page table corruption on THP permission changes.

Pull SCSI fixes from James Bottomley:
 "Three fixes.  One is the qla24xx MSI regression, one is a theoretical
  problem over blacklist matching, which would bite USB badly if it ever
  triggered and one is a system hang with a particular type of IPR
  device"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  qla2xxx: Fix NULL pointer deref in QLA interrupt
  SCSI: fix new bug in scsi_dev_info_list string matching
  ipr: Clear interrupt on croc/crocodile when running with LSI

Merge tag 'ecryptfs-4.7-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Provide a more concise fix for CVE-2016-1583:
   - Additionally fixes linux-stable regressions caused by the
     cherry-picking of the original fix

  Some very minor changes that have queued up:
   - Fix typos in code comments
   - Remove unnecessary check for NULL before destroying kmem_cache"

* tag 'ecryptfs-4.7-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  ecryptfs: don't allow mmap when the lower fs doesn't support it
  Revert "ecryptfs: forbid opening files without mmap handler"
  ecryptfs: fix spelling mistakes
  eCryptfs: fix typos in comment
  ecryptfs: drop null test before destroy functions

Pull IOMMU fixes from Joerg Roedel:
 "Two Fixes:

   - Intel VT-d fix for a suspend/resume issue, introduced with the
     scalability improvements in this cycle.

   - AMD IOMMU fix for systems that have unity mappings defined.  There
     was a race where translation got enabled before the unity mappings
     were in place.  This issue was seen on some HP servers"

* tag 'iommu-fixes-v4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix unity mapping initialization race
  iommu/vt-d: Fix infinite loop in free_all_cpu_cached_iovas

Pull xen bug fixes from David Vrabel:

 - Fix two bugs in the handling of xenbus transactions.

 - Make the xen acpi driver compatible with Xen 4.7.

* tag 'for-linus-4.7b-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/acpi: allow xen-acpi-processor driver to load on Xen 4.7
  xenbus: simplify xenbus_dev_request_and_reply()
  xenbus: don't bail early from xenbus_dev_request_and_reply()
  xenbus: don't BUG() on user mode induced condition

Pull arm64 fixes from Will Deacon:
 "A couple of late fixes here, but one that we've been sitting on for a
  few weeks while the details were worked out.  Specifically, we now
  enforce USER_DS on taking exceptions whilst in the kernel, which
  avoids leaking kernel data to userspace through things like perf.  The
  other patch is an update to a workaround for a hardware erratum on
  some Cavium SoCs.

  Summary:

   - Enforce USER_DS on exception entry from EL1

   - Apply workaround for Cavium errata #27456 on Thunderx-81xx parts"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Enable workaround for Cavium erratum 27456 on thunderx-81xx
  arm64: kernel: Save and restore UAO and addr_limit on exception entry

Pull x86 fixes from Ingo Molnar:
 "Three fixes:

   - A boot crash fix with certain configs
   - a MAINTAINERS entry update
   - Documentation typo fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/Documentation: Fix various typos in Documentation/x86/ files
  x86/amd_nb: Fix boot crash on non-AMD systems
  MAINTAINERS: Update the Calgary IOMMU entry

Pull scheduler fixes from Ingo Molnar:
 "Two load-balancing fixes for cgroups-intense workloads"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix calc_cfs_shares() fixed point arithmetics width confusion
  sched/fair: Fix effective_load() to consistently use smoothed load

Pull perf fixes from Ingo Molnar:
 "Various fixes:

   - 32-bit callgraph bug fix
   - suboptimal event group scheduling bug fix
   - event constraint fixes for Broadwell/Skylake
   - RAPL module name collision fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix pmu::filter_match for SW-led groups
  x86/perf/intel/rapl: Fix module name collision with powercap intel-rapl
  perf/x86: Fix 32-bit perf user callgraph collection
  perf/x86/intel: Update event constraints when HT is off

Pull irq fixes from Ingo Molnar:
 "Two MIPS-GIC irqchip driver fixes to unbreak certain MIPS boards"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips-gic: Match IPI IRQ domain by bus token only
  irqchip/mips-gic: Map to VPs using HW VPNum

Pull GPIO fixes from Linus Walleij:
 "I don't like to toss in last minute patches, but these are all for
  things that are broken, and have bitten people for real.  Two of them
  go into stable.  Maybe all of them if the compile test problem is a
  pain in the ass also for stable folks.

  Final (hopefully) GPIO fixes for v4.7:

   - Fix an oops on the Asus Eee PC 1201

   - Revert a patch trying to split GPIO parsing and GPIO configuration

   - Revert a too liberal compile testing thing"

* tag 'gpio-v4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  Revert "gpio: gpiolib-of: Allow compile testing"
  Revert "gpiolib: Split GPIO flags parsing and GPIO configuration"
  gpio: sch: Fix Oops on module load on Asus Eee PC 1201

Pull drm fixes from Dave Airlie:
 "One nouveau fix, and a few AMD Polaris fixes and some Allwinner fixes.

  I've got some vmware fixes that I might send separate over the
  weekend, they fix some black screens, but I'm still debating them"

* tag 'drm-fixes-for-v4.7-rc7' of git://people.freedesktop.org/~airlied/linux:
  drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation.
  drm/amd/powerplay: fix bug that get wrong polaris evv voltage.
  drm/amd/powerplay: incorrectly use of the function return value
  drm/amd/powerplay: fix incorrect voltage table value for tonga
  drm/amd/powerplay: fix incorrect voltage table value for polaris10
  drm/nouveau/disp/sor/gf119: select correct sor when poking training pattern
  gpu: drm: sun4i_drv: add missing of_node_put after calling of_parse_phandle
  drm/sun4i: Send vblank event when the CRTC is disabled
  drm/sun4i: Report proper vblank

There are legitimate reasons to disallow mmap on certain files, notably
in sysfs or procfs.  We shouldn't emulate mmap support on file systems
that don't offer support natively.

CVE-2016-1583
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: stable@vger.kernel.org
[tyhicks: clean up f_op check by using ecryptfs_file_to_lower()]
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>

As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and
CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on
both Intel and AMD systems. Doing any kind of hardware capability
checks in the driver as a prerequisite was wrong anyway: With the
hypervisor being in charge, all such checking should be done by it. If
ACPI data gets uploaded despite some missing capability, the hypervisor
is free to ignore part or all of that data.

Ditch the entire check_prereq() function, and do the only valid check
(xen_initial_domain()) in the caller in its place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

No need to retain a local copy of the full request message, only the
type is really needed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

xenbus_dev_request_and_reply() needs to track whether a transaction is
open.  For XS_TRANSACTION_START messages it calls transaction_start()
and for XS_TRANSACTION_END messages it calls transaction_end().

If sending an XS_TRANSACTION_START message fails or responds with an
an error, the transaction is not open and transaction_end() must be
called.

If sending an XS_TRANSACTION_END message fails, the transaction is
still open, but if an error response is returned the transaction is
closed.

Commit 027bd7e8 ("xen/xenbus: Avoid synchronous wait on XenBus
stalling shutdown/restart") introduced a regression where failed
XS_TRANSACTION_START messages were leaving the transaction open.  This
can cause problems with suspend (and migration) as all transactions
must be closed before suspending.

It appears that the problematic change was added accidentally, so just
remove it.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>

Pull apparmor fix from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  apparmor: fix oops, validate buffer size in apparmor_setprocattr()

Pull ACPI fixes from Rafael Wysocki:
 "All of these fix recent regressions in ACPICA, in the ACPI PCI IRQ
  management code and in the ACPI AML debugger.

  Specifics:

   - Fix a lock ordering issue in ACPICA introduced by a recent commit
     that attempted to fix a deadlock in the dynamic table loading code
     which in turn appeared after changes related to the handling of
     module-level AML also made in this cycle (Lv Zheng).

   - Fix a recent regression in the ACPI IRQ management code that may
     cause PCI drivers to be unable to register an IRQ if that IRQ
     happens to be shared with a device on the ISA bus, like the
     parallel port, by reverting one commit entirely and restoring the
     previous behavior in two other places (Sinan Kaya).

   - Fix a recent regression in the ACPI AML debugger introduced by the
     commit that removed incorrect usage of IS_ERR_VALUE() from multiple
     places (Lv Zheng)"

* tag 'acpi-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
  ACPICA: Namespace: Fix namespace/interpreter lock ordering
  ACPI,PCI,IRQ: separate ISA penalty calculation
  Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
  ACPI,PCI,IRQ: factor in PCI possible

Pull power management fixes from Rafael Wysocki:
 "One fix for a recent cpuidle core change that, against all odds,
  introduced a functional regression on Power systems and the fix for
  the crash during resume from hibernation on x86-64 that has been in
  the works for the last few weeks (it actually was ready last week, but
  I wanted to allow the reporters to test if for some more time).

  Specifics:

   - Fix a recent performance regression on Power systems (powernv and
     pseries) introduced by a core cpuidle commit that decreased the
     precision of the last_residency conversion from nano- to
     microseconds, which should not matter in theory, but turned out to
     play not-so-well with the special "snooze" idle state on Power
     (Shreyas B Prabhu).

   - Fix a crash during resume from hibernation on x86-64 caused by
     possible corruption of the kernel text part of page tables in the
     last phase of image restoration exposed by a security-related
     change during the 4.3 development cycle (Rafael Wysocki)"

* tag 'pm-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: Fix last_residency division
  x86/power/64: Fix kernel text mapping corruption during image restoration

Merge tag 'sunxi-drm-fixes-for-4.7-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-fixes

Allwinner DRM driver fixes for 4.7, take 2

A new set of fixes for the sun4i driver, mostly related to vblank handling,
and a minor fix to release a reference on the device tree nodes we're
parsing in the probe logic.

* tag 'sunxi-drm-fixes-for-4.7-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  gpu: drm: sun4i_drv: add missing of_node_put after calling of_parse_phandle
  drm/sun4i: Send vblank event when the CRTC is disabled
  drm/sun4i: Report proper vblank

When proc_pid_attr_write() was changed to use memdup_user apparmor's
(interface violating) assumption that the setprocattr buffer was always
a single page was violated.

The size test is not strictly speaking needed as proc_pid_attr_write()
will reject anything larger, but for the sake of robustness we can keep
it in.

SMACK and SELinux look safe to me, but somebody else should probably
have a look just in case.

Based on original patch from Vegard Nossum <vegard.nossum@oracle.com>
modified for the case that apparmor provides null termination.

Fixes: bb646cdbReported-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: stable@kernel.org
Signed-off-by: John Johansen <john.johansen@canonical.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>

This reverts commit 2f36db71.

It fixed a local root exploit but also introduced a dependency on
the lower file system implementing an mmap operation just to open a file,
which is a bit of a heavy hammer.  The right fix is to have mmap depend
on the existence of the mmap handler instead.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>

Pull block IO fixes from Jens Axboe:
 "Three small fixes that have been queued up and tested for this series:

   - A bug fix for xen-blkfront from Bob Liu, fixing an issue with
     incomplete requests during migration.

   - A fix for an ancient issue in retrieving the IO priority of a
     different PID than self, preventing that task from going away while
     we access it.  From Omar.

   - A writeback fix from Tahsin, fixing a case where we'd call ihold()
     with a zero ref count inode"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix use-after-free in sys_ioprio_get()
  writeback: inode cgroup wb switch should not call ihold()
  xen-blkfront: save uncompleted reqs in blkfront_resume()