- 12 May, 2012 40 commits
-
-
Rafael J. Wysocki authored
* renesas-kzm9g: ARM: mach-shmobile: kzm9g: enable SMP boot ARM: mach-shmobile: kzm9g: defconfig update ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key ARM: mach-shmobile: kzm9g: add SDHI support ARM: mach-shmobile: kzm9g: add MMCIF support ARM: mach-shmobile: kzm9g: correct screen direction ARM: mach-shmobile: sh73a0.h: add GPIO_NR ARM: mach-shmobile: pfc-sh73a0: fixup MSEL2CR MSEL18 for I2C-3 ARM: mach-shmobile: kzm9g: add ST1232 Touchscreen support ARM: mach-shmobile: kzm9g: add LCDC support ARM: mach-shmobile: kzm9g: add external USB Host support ARM: mach-shmobile: kzm9g: add SMSC 9221 support ARM: mach-shmobile: kzm9g: add defconfig ARM: mach-shmobile: add KZM-A9-GT board support Conflicts: arch/arm/mach-shmobile/Makefile
-
Kuninori Morimoto authored
Update the KZM9G defconfig and the code in platsmp.c to support SMP on the sh73a0 based KZM9G board. Also fix up the earlyprintk setting that was previously incorrect. Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by:
Magnus Damm <damm@opensource.se> Signed-off-by:
Rafael J. Wysocki <rjw@sisk.pl>
-
Kuninori Morimoto authored
This patch enable GPIO-KEY/FSI, and remove debug settings, and be cleanuped by c2330e28 script Signed-off-by:
Simon Horman <horms@verge.net.au> Acked-by:
-
Kuninori Morimoto authored
This patch adds extra GPIO via PCF8757 chip, and use it as gpio-key. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
The correct screen direction of KZM9G board needs PORT226/SC settings. Signed-off-by:
-
Kuninori Morimoto authored
GPIO_NR is added in order to clarify end of GPIO array. We can add extra GPIO from it. Signed-off-by:
-
Kuninori Morimoto authored
MSEL2CR MSEL18 should be 1 if I2C-3 Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
AS3711 chip initalization is required for enabling LCDC backlight, but there is no driver for this chip. So, this patch sends its settings when boot. Signed-off-by:
-
Kuninori Morimoto authored
This patch uses r8a66597_hcd driver, since renesas_usbhs driver doesn't support external R8A66597 chip. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
This adds very basic KZM-A9-GT board (SH73a0) support Signed-off-by:
-
Kuninori Morimoto authored
This patch enable USBFunc/SHDI/MMCIF, remove debug settings, and cleanuped by c2330e28 script Signed-off-by:
-
Kuninori Morimoto authored
armadillo800eva board is using sh-eth, but clock-r8a7740 didn't care it. This clock was enabled by boot-loader. This patch fix it up. Signed-off-by:
-
Kuninori Morimoto authored
The default 2MB size of DMA coherent memory isn't enough for allocate frame buffer memory. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
We can switch CON8/CON14 by SW1.5 SDHI1 is CON8 (SW1.5 = ON) Signed-off-by:
-
Kuninori Morimoto authored
On armadillo800eva board, CD (= Card Detect) pin is not connected to SDHI0_CD. Then, we can use IRQ31 as card detect irq, but it needs chattering removal operation. We should use IRQ card detect in the future, but this patch use polling mode at this point. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
This adds very basic armadillo800eva board (R-Mobile A1) support Signed-off-by:
-
Kuninori Morimoto authored
If the clocks is always same value as the parent clock, we can use followparent_recalc() for .recalc Reported-by:
Paul Mundt <lethal@linux-sh.org> Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
R8A7740 USB needs many clocks for workaround, and it has confusing name "usb24s" and "usb24". This "usb24s" will be used by other clocks. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Current workaround of I2C on r8a7740 used mdelay(), but it was an overkill. This patch cleans up the workaround delay. Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Kuninori Morimoto authored
Signed-off-by:
-
Magnus Damm authored
Update the mach-shmobile shared delay calibration code for late timers. All existing in-tree non-DT socs are however using early timers today and they are unaffected by this change. The patch modifies shmobile_setup_delay() from using lpj_fine to preset_lpj. This change allows us to preset the worst case loops-per-jiffy value to all CPU cores on the system. The old code which made use of lpj_fine did not affect the secondary CPU cores which made it impossible to boot on SMP without early timers. Needed for SMP SoCs using late timers like EMEV2 or any other mach-shmobile SMP SoC that makes use of late timers via DT. Signed-off-by:
-
Rafael J. Wysocki authored
* renesas-dt: ARM: mach-shmobile: sh7372 generic board support via DT V2 ARM: mach-shmobile: Rework sh7372 INTCS demuxer V2 ARM: mach-shmobile: Use INTC_IRQ_PINS_16H on sh7372 ARM: mach-shmobile: Use 0x3400 as INTCS vector offset ARM: mach-shmobile: Introduce INTC_IRQ_PINS_16H ARM: mach-shmobile: Introduce shmobile_setup_delay()
-
Magnus Damm authored
Make sure L1 caches are invalidated when booting secondary cores. Needed to boot all mach-shmobile SMP systems that are using Cortex-A9 including sh73a0, r8a7779 and EMEV2. Thanks to imx and tegra guys for actual code. Signed-off-by:
-
Kuninori Morimoto authored
Fix SMP TWD boot regression on sh73a0 based platforms caused by: 4200b16d ARM: shmobile: convert to twd_local_timer_register() interface After the merge of the above commit it has been impossible to boot sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The kernel crashes at smp_init_cpus() timing which is before the console has been initialized, so to the user this looks like a kernel lock up without any particular error message. This patch fixes the regression on sh73a0 by moving the TWD registration code from smp_init_cpus() to sys_timer->init() time. This patch removed shmobile_twd_init() which is no longer needed Signed-off-by:
-
