Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.

While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.

Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.

This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.

Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used.  Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.)  This
is important for sleep/suspend so there is a valid counter during
sleep.  Note that the suspend/sleep code needs fixing to check for
overflows of this counter.

In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics.  A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.

This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc.  Remove this
duplication and use generic hooks based on IRQ type.

Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run.  Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Convert OSK board to use new tps65010 gpiolib support.  This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Make the tps65010 driver use gpiolib to expose its GPIOs.

Note: This patch will get merged via omap tree instead of I2C
as it will cause some board updates. This has been discussed
at on the I2C list:

http://lists.lm-sensors.org/pipermail/i2c/2008-March/003031.htmlSigned-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

Start cleaning up GPIO handling for OMAP5912 OSK board:

 - Initialize GPIOs using the cross-platform calls, not the old
   OMAP-private ones.

 - Move touchscreen setup out of ads7846 code into board-specfic
   setup code, where it belongs.

This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update OMAP to use the new GPIO implementation framework.  This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* 'docs' of git://git.lwn.net/linux-2.6:
  Add additional examples in Documentation/spinlocks.txt
  Move sched-rt-group.txt to scheduler/
  Documentation: move rpc-cache.txt to filesystems/
  Documentation: move nfsroot.txt to filesystems/
  Spell out behavior of atomic_dec_and_lock() in kerneldoc
  Fix a typo in highres.txt
  Fixes to the seq_file document
  Fill out information on patch tags in SubmittingPatches
  Add the seq_file documentation

Checkpatch will throw an error if code doesn't use the correct initializers
for static spinlocks:

ERROR: Use of SPIN_LOCK_UNLOCKED is deprecated: see Documentation/spinlocks.txt

This is fine, but Documentation/spinlocks.txt isn't very clear on how to
_use_ the new initializers for static variables. To save people time in the
future, I added two small examples of how to fix old-style static
initializers to be more lockdep friendly.
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

This file is nfs-related.  (Maybe Documentation/filesystems/ would
benefit from a separate nfs/ directory at some point.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Documentation/ is a little large, and filesystems/ seems an obvious
place for this file.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

A little more detail here wouldn't hurt.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

git commit 54a01510 ("asmlinkage_protect
replaces prevent_tail_call") causes this build failure on s390:

    AS      arch/s390/kernel/entry64.o
  In file included from arch/s390/kernel/entry64.S:14:
  include/linux/linkage.h:34: error: syntax error in macro parameter list
  make[1]: *** [arch/s390/kernel/entry64.o] Error 1
  make: *** [arch/s390/kernel] Error 2

and some other architectures.  The reason is that some architectures add
the "-traditional" flag to the invocation of $(AS), which disables
variadic macro argument support.

So just surround the new define with an #ifndef __ASSEMBLY__ to prevent
any side effects on asm code.

Cc: Roland McGrath <roland@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c-tiny-usb: New VID/PID pair
  i2c-davinci: Fix lost interrupt
  i2c-ibm_iic: Fast mode parm desc fixup

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [NETNS][IPV6] tcp - assign the netns for timewait sockets
  [IPV4]: Fix byte value boundary check in do_ip_getsockopt().
  BNX2X: Correct bringing chip out of reset
  [NETFILTER]: nf_nat: autoload IPv4 connection tracking
  [NETFILTER]: xt_hashlimit: fix mask calculation
  [XFRM]: xfrm_user: fix selector family initialization
  rt61pci: rt61pci_beacon_update do not free skb twice
  ssb-mipscore: Fix interrupt vectors
  ssb-pcicore: Fix IRQ TPS flag handling
  mac80211: use short_preamble mode from capability if ERP IE not present
  [NET]: Undo code bloat in hot paths due to print_mac().
  [TCP]: Don't allow FRTO to take place while MTU is being probed
  [TCP]: tcp_simple_retransmit can cause S+L
  [TCP]: Fix NewReno's fast rexmit/recovery problems with GSOed skb
  [TCP]: Restore 2.6.24 mark_head_lost behavior for newreno/fack
  nl80211: fix STA AID bug
  b43legacy: fix bcm4303 crash
  iwlwifi: fix n-band association problem
  ipw2200: set MAC address on radiotap interface
  libertas: fix mode initialization problem

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC]: Fix several regset and ptrace bugs.

Michael Kerrisk found out that signalfd was not reporting back user data
pushed using sigqueue:

  http://groups.google.com/group/linux.kernel/msg/9397cab8551e3123

The following patch makes signalfd report back the ssi_ptr and ssi_int members
of the signalfd_siginfo structure.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Acked-by: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Increase the PNP "number of devices" limit.  We currently use an unsigned
char, which limits us to 256 devices per protocol.  This patch changes that to
an unsigned int.

Not all backends can take advantage of this: we limit ISAPNP to 10 devices in
isapnp_cfg_begin(), and PNPBIOS is limited to 256 devices because the BIOS
interfaces use a one-byte device node number.

But there is no limit on the number of PNPACPI devices we may have.  Large HP
Integrity machines have more than 256, which causes the current "unsigned char
number" to wrap around.  This causes errors like this:

    pnp: PnP ACPI init
    kobject_add failed for 00:00 with -EEXIST, don't try to register things with the same name in the same directory.

    Call Trace:
     [<a000000100010720>] show_stack+0x40/0xa0
     [<a0000001000107b0>] dump_stack+0x30/0x60
     [<a0000001001dbdf0>] kobject_add+0x290/0x2c0
     [<a0000001002bfd40>] device_add+0x160/0x860
     [<a0000001002c0470>] device_register+0x30/0x60
     [<a00000010026ba70>] __pnp_add_device+0x130/0x180
     [<a00000010026bb70>] pnp_add_device+0xb0/0xe0
     [<a0000001007f2730>] pnpacpi_add_device+0x510/0x5a0
     [<a0000001007f2810>] pnpacpi_add_device_handler+0x50/0x80

This patch increases the limit to fix this PNPACPI problem.  It should not
have any adverse effect on ISAPNP or PNPBIOS because their limits are still
enforced in the backends.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If a failure is detected after a parity check operation has been initiated,
but before it completes handle_parity_checks5 will never quiesce operations on
the stripe.

Explicitly handle this case by "canceling" the parity check, i.e.  clear the
STRIPE_OP_CHECK flags and queue the stripe on the handle list again to refresh
any non-uptodate blocks.

Kernel versions >= 2.6.23 are susceptible.

Cc: <stable@kernel.org>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds the missing include directive <linux/scatterlist.h> to the
cciss.c source file.    This was discovered by our release team when building
the kernel for the Alpha architecture.

Errors were found as references to functions 'sg_init_table' and 'sg_page' do
not exist without the include for Alpha.
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable RTC
platform drivers, to re-enable module auto loading.

[dbrownell@users.sourceforge.net: more drivers, minor fix]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable watchdog
drivers, to re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable USB HCDs,
to allow re-enable auto loading.

[dbrownell@users.sourceforge.net: more drivers; registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable usb
peripheral drivers, to re-eable module auto loading.

[dbrownell@users.sourceforge.net: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable SPI
platform drivers, to allow module auto loading.

[dbrownell@users.sourceforge.net: more drivers: registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Jeff Roberson discovered a race when using kaio eventfd based notifications.
When it occurs it can lead tomissed wakeups and hung userspace.

This patch fixes the race by moving the notification inside the spinlocked
section of kaio.  The operation is safe since eventfd spinlock and kaio one
are unrelated.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Jeff Roberson <jroberson@chesapeake.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-s35390a uses BITREVERSE functions so it needs to select that config symbol
to ensure that the functions are built.

  drivers/built-in.o: In function `s35390a_set_datetime':
  linux-2.6.25-rc8-git7/drivers/rtc/rtc-s35390a.c:144: undefined reference to `byte_rev_table'
  drivers/built-in.o: In function `s35390a_get_datetime':
  linux-2.6.25-rc8-git7/drivers/rtc/rtc-s35390a.c:163: undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Extend the /proc/<pid>/cgroup file to include the appropriate hierarchy ID on
each line.

Currently this ID isn't really needed since a hierarchy can be completely
identified by the set of subsystems bound to it, but this is likely to change
in the near future in order to support stateless subsystems and
merging/rebinding of subsystems.  Getting this change into 2.6.25 reduces the
need for an API change later.
Signed-off-by: Paul Menage <menage@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I have recently bought some USB PIDs from EZPrototypes for my USB projects
and one will be for the i2c-tiny-usb. I have not yet started to use the new 
one in the official i2c-tiny-usb firmware since i think it makes sense to get 
the change into the kernel before releasing a modified firmware.

This patch adds support for the EZPrototypes USB vid/pid pair used in later
i2c-tiny-usb firmware versions (avrusb v1.06 and up, usbtiny v2.06 and up).
Signed-off-by: Till Harbaum <Till@Harbaum.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

DAVINCI_I2C_STR_REG is a write 1 to clear register,
so don't use a read/modify/write cycle.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Noticed this when grepping for fast mode module params, the i2c-ibm_iic
driver was using a non-existent variable for MODULE_PARM_DESC. Fix it up
to reflect what it's actually supposed to be describing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Copy the network namespace from the socket to the timewait socket.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's really a pretty ugly thing to need, and some day it will hopefully
be obviated by teaching gcc about the magic calling conventions for the
low-level system call code, but in the meantime we can at least add big
honking comments about why we need these insane and strange macros.

I took my comments from my version of the macro, but I ended up deciding
to just pick Roland's version of the actual code instead (with his
prettier syntax that uses vararg macros).  Thus the previous two commits
that actually implement it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use asmlinkage_protect in sys_io_getevents, because GCC for i386 with
CONFIG_FRAME_POINTER=n can decide to clobber an argument word on the
stack, i.e. the user struct pt_regs.  Here the problem is not a tail
call, but just the compiler's use of the stack when it inlines and
optimizes the body of the called function.  This seems to avoid it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>