We need to RCU protect the chanctx_conf access, so
do that.

Fixes: 585625c9 ("mac80211_hwsim: check TX and STA bandwidth")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220505230421.fb8055c081a2.Ic6da3307c77a909bd61a0ea25dc2a4b08fe1b03f@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

I switched to use my kernel.org address, the old kvalo@codeaurora.org address
doesn't work anymore.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Tested-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506084212.8952-1-kvalo@kernel.org

Currently MBSSID parameters in struct ieee80211_bss_conf
are not reset upon connection. This could be problematic
with some drivers in a scenario where the device first
connects to a non-transmit BSS and then connects to a
transmit BSS of a Multi BSS AP. The MBSSID parameters
which are set after connecting to a non-transmit BSS will
not be reset and the same parameters will be passed on to
the driver during the subsequent connection to a transmit
BSS of a Multi BSS AP.

For example, firmware running on the ath11k device uses the
Multi BSS data for tracking the beacon of a non-transmit BSS
and reports the driver when there is a beacon miss. If we do
not reset the MBSSID parameters during the subsequent
connection to a transmit BSS, then the driver would have
wrong MBSSID data and FW would be looking for an incorrect
BSSID in the MBSSID beacon of a Multi BSS AP and reports
beacon loss leading to an unstable connection.

Reset the MBSSID parameters upon every connection to solve this
problem.

Fixes: 78ac51f8 ("mac80211: support multi-bssid")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

When retrieving the S1G channel number from IEs, we should retrieve
the operating channel instead of the primary channel. The S1G operation
element specifies the main channel of operation as the oper channel,
unlike for HT and HE which specify their main channel of operation as
the primary channel.
Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com>
Signed-off-by: Bassem Dawood <bassem@morsemicro.com>
Link: https://lore.kernel.org/r/20220420041321.3788789-1-kieran.frewen@morsemicro.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Validate the S1G channel width input by user to ensure it matches
that of the requested channel
Signed-off-by: Kieran Frewen <kieran.frewen@morsemicro.com>
Signed-off-by: Bassem Dawood <bassem@morsemicro.com>
Link: https://lore.kernel.org/r/20220420041321.3788789-2-kieran.frewen@morsemicro.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220420105038.36443-1-nbd@nbd.nameSigned-off-by: Johannes Berg <johannes.berg@intel.com>

(cherry picked from commit 1f682dc9 in wireless-next)

Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.

While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.

Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.

The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3

Fixes: 9dcf6808 ("ath11k: add 11d scan offload support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215777
Cc: <stable@vger.kernel.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.comSigned-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220427111619.9758-1-kvalo@kernel.org

Set myself as a maintainer of iwlwifi driver as Luca is
moving to a new role.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220412190141.4543-1-gregory.greenman@intel.com

In Chrome OS, a large number of crashes is observed due to corrupted timer
lists. Steven Rostedt pointed out that this usually happens when a timer
is freed while still active, and that the problem is often triggered
by code calling del_timer() instead of del_timer_sync() just before
freeing.

Steven also identified the iwlwifi driver as one of the possible culprits
since it does exactly that.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Gregory Greenman <gregory.greenman@intel.com>
Fixes: 60e8abd9 ("iwlwifi: dbg_ini: add periodic trigger new API support")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # Linux v5.17.3-rc1 and Debian LLVM-14
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220411154210.1870008-1-linux@roeck-us.net

Our detector found a concurrent use-after-free bug when detaching an
NCI device. The main reason for this bug is the unexpected scheduling
between the used delayed mechanism (timer and workqueue).

The race can be demonstrated below:

Thread-1                           Thread-2
                                 | nci_dev_up()
                                 |   nci_open_device()
                                 |     __nci_request(nci_reset_req)
                                 |       nci_send_cmd
                                 |         queue_work(cmd_work)
nci_unregister_device()          |
  nci_close_device()             | ...
    del_timer_sync(cmd_timer)[1] |
...                              | Worker
nci_free_device()                | nci_cmd_work()
  kfree(ndev)[3]                 |   mod_timer(cmd_timer)[2]

In short, the cleanup routine thought that the cmd_timer has already
been detached by [1] but the mod_timer can re-attach the timer [2], even
it is already released [3], resulting in UAF.

This UAF is easy to trigger, crash trace by POC is like below

[   66.703713] ==================================================================
[   66.703974] BUG: KASAN: use-after-free in enqueue_timer+0x448/0x490
[   66.703974] Write of size 8 at addr ffff888009fb7058 by task kworker/u4:1/33
[   66.703974]
[   66.703974] CPU: 1 PID: 33 Comm: kworker/u4:1 Not tainted 5.18.0-rc2 #5
[   66.703974] Workqueue: nfc2_nci_cmd_wq nci_cmd_work
[   66.703974] Call Trace:
[   66.703974]  <TASK>
[   66.703974]  dump_stack_lvl+0x57/0x7d
[   66.703974]  print_report.cold+0x5e/0x5db
[   66.703974]  ? enqueue_timer+0x448/0x490
[   66.703974]  kasan_report+0xbe/0x1c0
[   66.703974]  ? enqueue_timer+0x448/0x490
[   66.703974]  enqueue_timer+0x448/0x490
[   66.703974]  __mod_timer+0x5e6/0xb80
[   66.703974]  ? mark_held_locks+0x9e/0xe0
[   66.703974]  ? try_to_del_timer_sync+0xf0/0xf0
[   66.703974]  ? lockdep_hardirqs_on_prepare+0x17b/0x410
[   66.703974]  ? queue_work_on+0x61/0x80
[   66.703974]  ? lockdep_hardirqs_on+0xbf/0x130
[   66.703974]  process_one_work+0x8bb/0x1510
[   66.703974]  ? lockdep_hardirqs_on_prepare+0x410/0x410
[   66.703974]  ? pwq_dec_nr_in_flight+0x230/0x230
[   66.703974]  ? rwlock_bug.part.0+0x90/0x90
[   66.703974]  ? _raw_spin_lock_irq+0x41/0x50
[   66.703974]  worker_thread+0x575/0x1190
[   66.703974]  ? process_one_work+0x1510/0x1510
[   66.703974]  kthread+0x2a0/0x340
[   66.703974]  ? kthread_complete_and_exit+0x20/0x20
[   66.703974]  ret_from_fork+0x22/0x30
[   66.703974]  </TASK>
[   66.703974]
[   66.703974] Allocated by task 267:
[   66.703974]  kasan_save_stack+0x1e/0x40
[   66.703974]  __kasan_kmalloc+0x81/0xa0
[   66.703974]  nci_allocate_device+0xd3/0x390
[   66.703974]  nfcmrvl_nci_register_dev+0x183/0x2c0
[   66.703974]  nfcmrvl_nci_uart_open+0xf2/0x1dd
[   66.703974]  nci_uart_tty_ioctl+0x2c3/0x4a0
[   66.703974]  tty_ioctl+0x764/0x1310
[   66.703974]  __x64_sys_ioctl+0x122/0x190
[   66.703974]  do_syscall_64+0x3b/0x90
[   66.703974]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   66.703974]
[   66.703974] Freed by task 406:
[   66.703974]  kasan_save_stack+0x1e/0x40
[   66.703974]  kasan_set_track+0x21/0x30
[   66.703974]  kasan_set_free_info+0x20/0x30
[   66.703974]  __kasan_slab_free+0x108/0x170
[   66.703974]  kfree+0xb0/0x330
[   66.703974]  nfcmrvl_nci_unregister_dev+0x90/0xd0
[   66.703974]  nci_uart_tty_close+0xdf/0x180
[   66.703974]  tty_ldisc_kill+0x73/0x110
[   66.703974]  tty_ldisc_hangup+0x281/0x5b0
[   66.703974]  __tty_hangup.part.0+0x431/0x890
[   66.703974]  tty_release+0x3a8/0xc80
[   66.703974]  __fput+0x1f0/0x8c0
[   66.703974]  task_work_run+0xc9/0x170
[   66.703974]  exit_to_user_mode_prepare+0x194/0x1a0
[   66.703974]  syscall_exit_to_user_mode+0x19/0x50
[   66.703974]  do_syscall_64+0x48/0x90
[   66.703974]  entry_SYSCALL_64_after_hwframe+0x44/0xae

To fix the UAF, this patch adds flush_workqueue() to ensure the
nci_cmd_work is finished before the following del_timer_sync.
This combination will promise the timer is actually detached.

Fixes: 6a2968aa ("NFC: basic NCI protocol implementation")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This switch is not even supported, but if someone were to actually put
this compatible string "realtek,rtl8366s" in their device tree, they
would be greeted with a kernel panic because the probe function would
dereference NULL. So let's just remove it.

Link: https://lore.kernel.org/all/CACRpkdYdKZs0WExXc3=0yPNOwP+oOV60HRz7SRoGjZvYHaT=1g@mail.gmail.com/Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The kernel test robot reported a build failure:

or1k-linux-ld: drivers/net/dsa/realtek/realtek-smi.o:(.rodata+0x16c): undefined reference to `rtl8366rb_variant'

... with the following build configuration:

CONFIG_NET_DSA_REALTEK=y
CONFIG_NET_DSA_REALTEK_SMI=y
CONFIG_NET_DSA_REALTEK_RTL8365MB=y
CONFIG_NET_DSA_REALTEK_RTL8366RB=m

The problem here is that the realtek-smi interface driver gets built-in,
while the rtl8366rb switch subdriver gets built as a module, hence the
symbol rtl8366rb_variant is not reachable when defining the OF device
table in the interface driver.

The Kconfig dependencies don't help in this scenario because they just
say that the subdriver(s) depend on at least one interface driver. In
fact, the subdrivers don't depend on the interface drivers at all, and
can even be built even in their absence. Somewhat strangely, the
interface drivers can also be built in the absence of any subdriver,
BUT, if a subdriver IS enabled, then it must be reachable according to
the linkage of the interface driver: effectively what the IS_REACHABLE()
macro achieves. If it is not reachable, the above kind of linker error
will be observed.

Rather than papering over the above build error by simply using
IS_REACHABLE(), we can do a little better and admit that it is actually
the interface drivers that have a dependency on the subdrivers. So this
patch does exactly that. Specifically, we ensure that:

1. The interface drivers' Kconfig symbols must have a value no greater
   than the value of any subdriver Kconfig symbols.

2. The subdrivers should by default enable both interface drivers, since
   most users probably want at least one of them; those interface
   drivers can be explicitly disabled however.

What this doesn't do is prevent a user from building only a subdriver,
without any interface driver. To that end, add an additional line of
help in the menu to guide users in the right direction.

Link: https://lore.kernel.org/all/202204110757.XIafvVnj-lkp@intel.com/Reported-by: kernel test robot <lkp@intel.com>
Fixes: aac94001 ("net: dsa: realtek: add new mdio interface for drivers")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kalle Valo says:

====================
wireless fixes for v5.18

First set of fixes for v5.18. Maintainers file updates, two
compilation warning fixes, one revert for ath11k and smaller fixes to
drivers and stack. All the usual stuff.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

AST2600 MAC register 0x58 is writable only when the MAC clock is
enabled.  Usually, the MAC clock is enabled by the bootloader so
register 0x58 is set normally when the bootloader is involved.  To make
ast2600 ftgmac100 work without the bootloader, postpone the register
write until the clock is ready.

Fixes: 137d23ce ("net: ftgmac100: Fix Aspeed ast2600 TX hang issue")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 11fd667d.

dsa_slave_change_mtu() updates the MTU of the DSA master and of the
associated CPU port, but only if it detects a change to the master MTU.

The blamed commit in the Fixes: tag below addressed a regression where
dsa_slave_change_mtu() would return early and not do anything due to
ds->ops->port_change_mtu() not being implemented.

However, that commit also had the effect that the master MTU got set up
to the correct value by dsa_master_setup(), but the associated CPU port's
MTU did not get updated. This causes breakage for drivers that rely on
the ->port_change_mtu() DSA call to account for the tagging overhead on
the CPU port, and don't set up the initial MTU during the setup phase.

Things actually worked before because they were in a fragile equilibrium
where dsa_slave_change_mtu() was called before dsa_master_setup() was.
So dsa_slave_change_mtu() could actually detect a change and update the
CPU port MTU too.

Restore the code to the way things used to work by reverting the reorder
of dsa_tree_setup_master() and dsa_tree_setup_ports(). That change did
not have a concrete motivation going for it anyway, it just looked
better.

Fixes: 066dfc42 ("Revert "net: dsa: stop updating master MTU from master.c"")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MACVLAN receive handler clones skbs to all matching source MACVLAN
interfaces, before it passes the packet along to match on destination
based MACVLANs.

When using the MACVLAN nodst mode, passing the packet to destination based
MACVLANs is omitted and the handler returns with RX_HANDLER_CONSUMED.
However, the passed skb is not freed, leaking for any packet processed
with the nodst option.

Properly free the skb when consuming packets to fix that leak.

Fixes: 427f0c8c ("macvlan: Add nodst option to macvlan type source")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

1) Fix cgroupv2 from the input path, from Florian Westphal.

2) Fix incorrect return value of nft_parse_register(), from Antoine Tenart.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_tables: nft_parse_register can return a negative value
  netfilter: nft_socket: make cgroup match work in input too
====================

Link: https://lore.kernel.org/r/20220412094246.448055-1-pablo@netfilter.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since commit 6e1acfa3 ("netfilter: nf_tables: validate registers
coming from userspace.") nft_parse_register can return a negative value,
but the function prototype is still returning an unsigned int.

Fixes: 6e1acfa3 ("netfilter: nf_tables: validate registers coming from userspace.")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Horatiu Vultur says:

====================
net: lan966x: lan966x fixes

This contains different fixes for lan966x in different areas like PTP, MAC,
Switchdev and IGMP processing.
====================

Link: https://lore.kernel.org/r/20220409184143.1204786-1-horatiu.vultur@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently when getting a new MAC is learn, the HW generates an
interrupt. So then the SW will check the new entry and checks if it
arrived on a correct port. If it didn't just generate a warning.
But this could still crash the system. Therefore stop processing that
entry when an issue is seen.

Fixes: 5ccd66e0 ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On lan966x it is not allowed to have foreign interfaces under a bridge
which already contains lan966x ports. So when a port leaves the bridge
it would call switchdev_bridge_port_unoffload which eventually will
notify the other ports that bridge left the vlan group but that is not
true because the bridge is still part of the vlan group.

Therefore when a port leaves the bridge, stop generating replays because
already the HW cleared after itself and the other ports don't need to do
anything else.

Fixes: cf2f6089 ("net: lan966x: Add support to offload the forwarding.")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case an IGMP frame has a vlan tag, then the function
lan966x_hw_offload couldn't figure out that is a IGMP frame. Therefore
the SW thinks that the frame was already forward by the HW which is not
true.
Extend lan966x_hw_offload to pop the vlan tag if are any and then check
for IGMP frames.

Fixes: 47aeea0d ("net: lan966x: Implement the callback SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED ")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The clk_per_cfg register represents the value added to the system clock
for each clock cycle. The issue is that the default value is wrong,
meaning that in case the DUT was a grandmaster then everone in the
network was too slow. In case there was a grandmaster, then there is no
issue because the DUT will configure clk_per_cfg register based on the
master frequency.

Fixes: d0964594 ("net: lan966x: Add support for ptp clocks")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Function sctp_do_peeloff() wrongly initializes daddr of the original
socket instead of the peeled off socket, which makes getpeername()
return zeroes instead of the primary address. Initialize the new socket
instead.

Fixes: d570ee49 ("[SCTP]: Correctly set daddr for IPv6 sockets during peeloff")
Signed-off-by: Petr Malat <oss@malat.biz>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/20220409063611.673193-1-oss@malat.bizSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-04-08

Alexander fixes a use after free issue with aRFS for ice driver.

Mateusz reverts a commit that introduced issues related to device
resets for iavf driver.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  Revert "iavf: Fix deadlock occurrence during resetting VF interface"
  ice: arfs: fix use-after-free when freeing @rx_cpu_rmap
====================

Link: https://lore.kernel.org/r/20220408163411.2415552-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Karsten Graul says:

====================
net/smc: fixes 2022-04-08

Patch 1 fixes two usages of snprintf() with non null-terminated
string which results into an out-of-bounds read.
Pach 2 fixes a syzbot finding where a pointer check was missed
before the call to dev_name().
Patch 3 fixes a crash when already released memory is used as
a function pointer.
====================

Link: https://lore.kernel.org/r/20220408151035.1044701-1-kgraul@linux.ibm.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Child sockets may inherit the af_ops from the parent listen socket.
When the listen socket is released then the af_ops of the child socket
points to released memory.
Solve that by restoring the original af_ops for child sockets which
inherited the parent af_ops. And clear any inherited user_data of the
parent socket.

Fixes: 8270d9c2 ("net/smc: Limit backlog connections")
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: D. Wythe <alibuda@linux.alibaba.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

dev_name() was called with dev.parent as argument but without to
NULL-check it before.
Solve this by checking the pointer before the call to dev_name().

Fixes: af5f60c7 ("net/smc: allow PCI IDs as ib device names in the pnet table")
Reported-by: syzbot+03e3e228510223dabd34@syzkaller.appspotmail.com
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using snprintf() to convert not null-terminated strings to null
terminated strings may cause out of bounds read in the source string.
Therefore use memcpy() and terminate the target string with a null
afterwards.

Fixes: fa086662 ("net/smc: add support for user defined EIDs")
Fixes: 3c572145 ("net/smc: add generic netlink support for system EID")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

commit 42983885 ("net: macb: restart tx after tx used bit read")
added support for restarting transmission. Restarting tx does not work
in case controller asserts TXUBR interrupt and TQBP is already at the end
of the tx queue. In that situation, restarting tx will immediately cause
assertion of another TXUBR interrupt. The driver will end up in an infinite
interrupt loop which it cannot break out of.

For cases where TQBP is at the end of the tx queue, instead
only clear TX_USED interrupt. As more data gets pushed to the queue,
transmission will resume.

This issue was observed on a Xilinx Zynq-7000 based board.
During stress test of the network interface,
driver would get stuck on interrupt loop within seconds or minutes
causing CPU to stall.
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220407161659.14532-1-tomas.melin@vaisala.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

kongweibin reported a kernel panic in ip6_forward() when input interface
has no in6 dev associated.

The following tc commands were used to reproduce this panic:
tc qdisc del dev vxlan100 root
tc qdisc add dev vxlan100 root netem corrupt 5%

CC: stable@vger.kernel.org
Fixes: ccd27f05 ("ipv6: fix 'disable_policy' for fwd packets")
Reported-by: kongweibin <kongweibin2@huawei.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both of of_get_parent() and of_parse_phandle() return node pointer with
refcount incremented, use of_node_put() on it to decrease refcount
when done.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

cgroupv2 helper function ignores the already-looked up sk
and uses skb->sk instead.

Just pass sk from the calling function instead; this will
make cgroup matching work for udp and tcp in input even when
edemux did not set skb->sk already.

Fixes: e0bb96db ("netfilter: nft_socket: add support for cgroupsv2")
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Don't use sizeof(pointer) when calculating scnprintf offset.

Fixes: 01f84f0e ("mac80211: reduce stack usage in debugfs")
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20220406175659.20611-1-greearb@candelatech.com
[correct the Fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Synchronize additions to nontrans_list of transmitting BSS with
bss_lock to avoid races. Also when cfg80211_add_nontrans_list() fails
__cfg80211_unlink_bss() needs bss_lock to be held (has lockdep assert
on bss_lock). So protect the whole block with bss_lock to avoid
races and warnings. Found during code review.

Fixes: 0b8fb823 ("cfg80211: Parsing of Multiple BSSID information in scanning")
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649668071-9370-1-git-send-email-quic_ramess@quicinc.comSigned-off-by: Johannes Berg <johannes.berg@intel.com>

We need this to be at least two bytes, so we can access
alpha2[0] and alpha2[1]. It may be three in case some
userspace used NUL-termination since it was NLA_STRING
(and we also push it out with NUL-termination).

Cc: stable@vger.kernel.org
Reported-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220411114201.fd4a31f06541.Ie7ff4be2cf348d8cc28ed0d626fc54becf7ea799@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

A user may set the SO_TXTIME socket option to ensure a packet is send
at a given time. The taprio scheduler has to confirm, that it is allowed
to send a packet at that given time, by a check against the packet time
schedule. The scheduler drop the packet, if the gates are closed at the
given send time.

The check, if SO_TXTIME is set, may fail since sk_flags are part of an
union and the union is used otherwise. This happen, if a socket is not
a full socket, like a request socket for example.

Add a check to verify, if the union is used for sk_flags.

Fixes: 4cfd5779 ("taprio: Add support for txtime-assist mode")
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using a fixed-link, the altr_tse_pcs driver crashes
due to null-pointer dereference as no phy_device is provided to
tse_pcs_fix_mac_speed function. Fix this by adding a check for
phy_dev before calling the tse_pcs_fix_mac_speed() function.

Also clean up the tse_pcs_fix_mac_speed function a bit. There is
no need to check for splitter_base and sgmii_adapter_base
because the driver will fail if these 2 variables are not
derived from the device tree.

Fixes: fb3bbdb8 ("net: ethernet: Add TSE PCS support to dwmac-socfpga")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the T1 phy master/slave state is changed, at the end of config_aneg
function genphy_softreset is called. After the reset all the registers
configured during the config_init are restored to default value.
To avoid this, removed the genphy_softreset call.

v1->v2
------
Added the author in cc

Fixes: 8a1b415d ("net: phy: added ethtool master-slave configuration support")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ieee80211_tx_info_clear_status() helper also clears the rate counts and
the driver-private part of struct ieee80211_tx_info, so using it breaks
quite a few other things. So back out of using it, and instead define a
ath-internal helper that only clears the area between the
status_driver_data and the rates info. Combined with moving the
ath_frame_info struct to status_driver_data, this avoids clearing anything
we shouldn't be, and so we can keep the existing code for handling the rate
information.

While fixing this I also noticed that the setting of
tx_info->status.rates[tx_rateindex].count on hardware underrun errors was
always immediately overridden by the normal setting of the same fields, so
rearrange the code so that the underrun detection actually takes effect.

The new helper could be generalised to a 'memset_between()' helper, but
leave it as a driver-internal helper for now since this needs to go to
stable.

Cc: stable@vger.kernel.org
Reported-by: Peter Seiderer <ps.report@gmx.net>
Fixes: 037250f0 ("ath9k: Properly clear TX status area before reporting to mac80211")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Peter Seiderer <ps.report@gmx.net>
Tested-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220404204800.2681133-1-toke@toke.dk