This is a pure documentation, to try to explain why the cache flushing code
for the SH4 is implemented the way it is.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Optimise memcpy_to/fromio. This is used extensivly by MTD, so is a
worthwhile performance gain. The main savings come from not repeatedly
calling readl/writel, and doing word instead of byte at a time
transfers. Also using "movca.l" on SH4 gives a small performance win.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

After performing the port2addr conversion, and checking that the data is
correctly aligned, simply call __raw_readsX/writesX. These have already been
optimised.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Reading from the ROM is not a good idea as it could disturb some
flash operation that it is in progress.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The SH instruction set has several instructions which accept an 8 bit
immediate operand. For logical instructions this operand is zero extended,
for arithmetic instructions the operand is sign extended. After adding an
option to the assembler to check this, it was found that several pieces
of assembly code were assuming this behaviour, and in one case
getting it wrong.

So this patch explicitly sign extends any immediate operands, which makes
it obvious what is happening, and fixes the one case which got it wrong.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

So far kernel command line arguments could be passed in by a bootloader
or defined as CONFIG_CMDLINE, which completely overwriting the first one.

This change allows a developer to declare selected kernel parameters in
a kernel configuration (eg. project-specific defconfig), retaining
possibility of passing others by a bootloader.

The obvious examples of the first type are MTD partition or
bigphysarea-like region definitions, while "debug" option or network
configuration should be given by a bootloader or a JTAG boot script.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patches will trigger a reboot using the watchdog
timer instead of double fault.  Unlike the previous
method, this one actually works in 32 bit mode.

Reset should also be cleaner.
Signed-off-by: Jon Frosdick <jon.frosdick@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Save the VBR allowing GDB to dump full registers set but do not reload it
as soon as the kgdb_handle_exception is invoked.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.

This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

GCC does not issue unwind information for function epilogues.
Unfortunately we can catch a signal during an epilogue.  The signal
handler writes the current context and signal return code onto the stack
overwriting previous contents.  During unwinding, libgcc can try to
restore registers from the stack and restores corrupted ones. This can
lead to segmentation, misaligned access and sigbus faults.

For example, consider the following code:

    mov.l   r12,@-r15
    mov.l   r14,@-r15
    sts.l   pr,@-r15
    mov     r15,r14

    <do stuff>

    mov r14, r15
    lds.l @r15+, pr
	<<< SIGNAL HERE
    mov.l @r15+, r14
    mov.l @r15+, r12
    rts

Unwind is aware that pr was pushed to stack in prolog, so tries to
restore it.  Unfortunately it restores the last word of the signal
handler code placed on the stack by the kernel.

This patch tries to avoid the problem by adding a guard region on the
stack between where the function pushes data and where the signal handler
pushes its return code.  We probably don't see this problem often because
exception handling unwinding in an epilogue only occurs due to a pthread
cancel signal.  Also the kernel signal stack handler alignment of 8 bytes
could hide the occurance of this problem sometimes as the stack may not
be trampled at a particular required word.

This is not guaranteed to always work.  It relies on a frame pointer
existing for the function (so it can get the correct sp value) which is
not always the case for the SH4.

Modifications will also be made to libgcc for the case where there is no
fp.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch fixes a few problems with the existing code in do_address_error().

a) the variable used to printk()d the offending instruction wasn't
   initialized correctly. This is a fix to bug 5727

b) behaviour for CONFIG_CPU_SH2A wasn't correct

c) the 'ignore address error' behaviour didn't update the PC, causing an
   infinite loop.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch brings the SH4 misaligned trap handler in line with what
happens on ARM:
Add a /proc/cpu/alignment which can be read from to get alignment
trap statistics and written to to influence the behaviour of the
alignment trap handling. The value to write is a bitfield, which
has the following meaning: 1 warn, 2 fixup, 4 signal
In addition, we add a /proc/cpu/kernel_alignment, to enable or
disable warnings in case of kernel code causing alignment errors.

Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch makes sure we see messages about unaligned access fixups
every now and then. Else especially userspace apps suffering from
bad programming won't ever be noticed...

Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The Runtime PM patch for UIO driver implements coarse grained
dynamic power management for UIO devices. With that patch in
place we can get rid of the static clock configuration. Which
in turn makes it possible for cpuidle to enter deeper sleep.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

With the Runtime PM driver changes in place, we must have
Runtime PM support in place. Otherwise there is no way to
enable clocks to the Runtime PM enabled hardware blocks.
This patch makes Runtime PM mandatory on SuperH Mobile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The runtime PM for SH-Mobile code had platform_bus_notify() as __devinit,
which is rather bogus. Kill off the annotation, which subsequently
silences the section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modifies the uio_pdrv_genirq driver to support
Runtime PM. The power management implementation simply
runtime resumes the device at open() time and runtime
suspends it at release() time. The user space driver is
responsible for re-initializing the hardware after open().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modifies the SuperH Mobile CEU driver to support
Runtime PM. Driver callbacks for Runtime PM are empty because
the device registers are always re-initialized after
pm_runtime_get_sync(). The Runtime PM functions replaces the
clock framework module stop bit handling in this driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modifies the SuperH Mobile LCDC framebuffer driver
to support Runtime PM. The driver is using the functions

 - pm_runtime_get_sync()
 - pm_runtime_put_sync()

to inform the bus code if the hardware is idle or not. If the
hardware is idle then the bus code may call the runtime dev_pm_ops
callbacks to save and restore state. pm_runtime_resume() is used
to allow the driver to access the hardware from probe().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch is V3 of the SuperH Mobile Runtime PM platform bus
implentation matching Rafael's Runtime PM v16.

The code gets invoked from the SuperH specific Runtime PM
platform bus functions that override the weak symbols for:
 - platform_pm_runtime_suspend()
 - platform_pm_runtime_resume()
 - platform_pm_runtime_idle()

This Runtime PM implementation performs two levels of power
management. At the time of platform bus runtime suspend the
clock to the device is stopped instantly. Later on if all
devices within the power domain has their clocks stopped
then the device driver ->runtime_suspend() callbacks are
used to save hardware register state for each device.

Device driver ->runtime_suspend() calls are scheduled from
cpuidle context using platform_pm_runtime_suspend_idle().
When all devices have been fully suspended the processor
is allowed to enter deep sleep from cpuidle.

The runtime resume operation turns on clocks and also
restores registers if needed. It is worth noting that the
devices start in a suspended state and the device driver
is responsible for calling runtime resume before accessing
the actual hardware.

In this particular platform bus implementation runtime
resume is not allowed from interrupt context. Runtime
suspend is however allowed from interrupt context as
long as the synchronous functions are avoided.

[ updated for v17 -- PFM. ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This patch adds default Runtime PM callbacks to the dev_pm_ops
belonging to the platform bus. The callbacks are weak symbols
that architecture specific code can override.

Allows Runtime PM even though CONFIG_PM_SLEEP=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>

Introduce a core framework for run-time power management of I/O
devices.  Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'.  Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level.  Document all these things.

Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: check saved state before restore

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt2sas: fix config request and diag reset deadlock
  [SCSI] mpt2sas: Bump driver version 01.100.04.00
  [SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
  [SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
  [SCSI] mpt2sas: fix infinite loop inside config request
  [SCSI] mpt2sas: Excessive log info causes sas iounit page time out
  [SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
  [SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
  [SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash

The CIE and FDE structs are big enough and accessed regularly enough in
certain configurations to make cacheline alignment useful.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

In commit a8e7d49a ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.

That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable.  And
indeed, nothing bad seemed to happen.

Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:

	http://bugzilla.kernel.org/show_bug.cgi?id=13556
	http://bugzilla.kernel.org/show_bug.cgi?id=13756
	http://bugzilla.kernel.org/show_bug.cgi?id=13876

and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).

I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.
Pattern-pointed-out-by: Roland Kletzing <devzero@web.de>
Cc: stable@kernel.org (2.6.29 and 2.6.30)
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Conflicts:
	arch/sh/kernel/cpu/sh3/entry.S

sh64 does not yet support GENERIC_BUG, but still wants unwinder support.
Alias UNWINDER_BUG and UNWINDER_BUG_ON to their BUG counterparts until
the conversion to GENERIC_BUG is completed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This simplifies the unwinder trap handling, dropping the use of the
special trapa vector and simply piggybacking on top of the BUG support. A
new BUGFLAG_UNWINDER is added for flagging the unwinder fault, before
continuing on with regular BUG dispatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

If the oprofile code is built as a module, unwind_stack() as used by the
oprofile backtrace code is not available, causing build breakage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon: add GET_PARAM/INFO support for Z pipes
  drm/radeon/kms: add r100/r200 OQ support.
  drm: Fix sysfs device confusion.
  drm/radeon/kms: implement the bo busy ioctl properly.

* 'btrfs' of git://git.kernel.dk/linux-2.6-block:
  btrfs: fix inode rbtree corruption

As noted in 83d349f3 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask.  That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.

This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.

The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f962 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.

Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty.  But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.

See

	http://bugzilla.kernel.org/show_bug.cgi?id=13933

for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not.  In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.

So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.

Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>