usb drivers need to get the right value for otg clock so
calculate and return it
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

when CONFIG_USB_ULPI is not defined we actually get :
warning: 'otg_pdata' defined but not used
warning: 'usbh2_pdata' defined but not used
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: s.hauer@pengutronix.de
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

without this patch, ipu_clk's value is 0 thus preventing mx3fb from
calculating the right divisor for pixel clock generator.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Add device registration and setup IOMUX pins in the mx51_babbage
board feil.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch adds I2C functionality to the Freescale MX51 Babbage HW.
The patch adds device structures, i2c board slave device defines,
IOMUX pin defines, and clocks.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This patch fixes the clock refcounting when reparenting is used.

Boot-tested on imx51 babbage board.

Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.htmlSigned-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The keymap is taken from the Freescale supplied kernel.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Baruch Siach <baruch@tkos.co.il>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Based on work from Alberto Panizzo for MX3X
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

support copied from mach-pca100.c
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Like this one (if CONFIG_USB_ULPI is not set):

arch/arm/mach-mx3/mach-pcm043.c:312: warning: 'otg_pdata' defined but not used
arch/arm/mach-mx3/mach-pcm043.c:317: warning: 'usbh1_pdata' defined but not used
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

This makes the resistive touch interface work.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

CC      arch/arm/mach-mx3/mach-pcm037.o
  arch/arm/mach-mx3/mach-pcm037.c: In function 'mxc_board_init':
  arch/arm/mach-mx3/mach-pcm037.c:584: warning: unused variable 'tmp'
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (63 commits)
  drivers/net/usb/asix.c: Fix pointer cast.
  be2net: Bug fix to avoid disabling bottom half during firmware upgrade.
  proc_dointvec: write a single value
  hso: add support for new products
  Phonet: fix potential use-after-free in pep_sock_close()
  ath9k: remove VEOL support for ad-hoc
  ath9k: change beacon allocation to prefer the first beacon slot
  sock.h: fix kernel-doc warning
  cls_cgroup: Fix build error when built-in
  macvlan: do proper cleanup in macvlan_common_newlink() V2
  be2net: Bug fix in init code in probe
  net/dccp: expansion of error code size
  ath9k: Fix rx of mcast/bcast frames in PS mode with auto sleep
  wireless: fix sta_info.h kernel-doc warnings
  wireless: fix mac80211.h kernel-doc warnings
  iwlwifi: testing the wrong variable in iwl_add_bssid_station()
  ath9k_htc: rare leak in ath9k_hif_usb_alloc_tx_urbs()
  ath9k_htc: dereferencing before check in hif_usb_tx_cb()
  rt2x00: Fix rt2800usb TX descriptor writing.
  rt2x00: Fix failed SLEEP->AWAKE and AWAKE->SLEEP transitions.
  ...

* 'alpha-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
  alpha: simplify and optimize sched_find_first_bit
  alpha: invoke oom-killer from page fault
  Convert alpha to use clocksources instead of arch_gettimeoffset

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  driver core: add devname module aliases to allow module on-demand auto-loading

This reverts commit 480b02df, since
Rafael reports that it causes occasional kernel paging request faults in
load_module().

Dropping the module lock and re-taking it deep in the call-chain is
definitely not the right thing to do.  That just turns the mutex from a
lock into a "random non-locking data structure" that doesn't actually
protect what it's supposed to protect.
Requested-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Brandon Philips <brandon@ifup.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Stephen Rothwell reports the following new warning:

drivers/net/usb/asix.c: In function 'asix_rx_fixup':
drivers/net/usb/asix.c:325: warning: cast from pointer to integer of different size
drivers/net/usb/asix.c:354: warning: cast from pointer to integer of different size

The code just cares about the low alignment bits, so use
an "unsigned long" cast instead of one to "u32".
Signed-off-by: David S. Miller <davem@davemloft.net>

Certain firmware commands/operations to upgrade firmware could take several
seconds to complete. The code presently disables bottom half during these
operations which could lead to unpredictable behaviour in certain cases. This
patch now does all firmware upgrade operations asynchronously using a
completion variable.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 00b7c339
"sysctl: refactor integer handling proc code"
modified the behaviour of writing to /proc.
Before the commit, write("1\n") to /proc/sys/kernel/printk succeeded. But
now it returns EINVAL.

This commit supports writing a single value to a multi-valued entry.
Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp>
Reviewed-and-tested-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a few new product id's for the hso driver.
Signed-off-by: Filip Aben <f.aben@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_common_release() might destroy our last reference to the socket.
So an extra temporary reference is needed during cleanup.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Search only the first 100 bits instead of 140, saving a couple
instructions. The resulting code is about 1/3 faster (40K ticks/1000
iterations down to 30K ticks/1000 iterations).

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>