* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] pata_it821x: fix warning
  libata: Fix a large collection of DMA mode mismatches
  ahci: sis controllers actually can do PMP
  pata_via: clean up recent tf_load changes
  libata: restore SControl on detach
  libata: use ata_link_printk() when printing SError
  libata: always do follow-up SRST if hardreset returned -EAGAIN
  libata: fix EH action overwriting in ata_eh_reset()
  sata_mv: add the Gen IIE flag to the SoC devices.
  ata_piix: IDE Mode SATA patch for Intel Ibex Peak DeviceIDs
  ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
  sata_mv: don't issue two DMA commands concurrently
  libata: implement no[hs]rst force params

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Fix deadlock on RTNL in ipoib_stop()
  IB/ipath: Fix incorrect check for max physical address in TID
  IB/ipath: Fix lost UD send work request

Reported by Andrew Morton:
drivers/ata/pata_it821x.c: In function 'it821x_port_start':
drivers/ata/pata_it821x.c:609: warning: 'mtype' may be used uninitialized in
this function

Pretty horrid fix, but so's a warning..
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.

This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.

Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)

Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
 <dave.mueller@gmx.ch>  -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

SIS controllers were blacklisted for PMP as enabling it made device
detection fail whether the device was PMP or not - the natural
conclusion was the controller chokes on SRST w/ pmp==15.  However, it
turned out that the controller just didn't like issuing SRST after
hardreset w/o clearing SError first.  Interestingly, the SRST itself
succeeds but the following commands fail.

If SError is cleared between hardreset and SRST, which is the default
behavior now, everything works fine and SIS controllers work with PMPs
happily.

Remove PMP blacklisting for SIS AHCIs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Piter PUNK <piterpunk@slackware.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit bfce5e01 implemented custom
tf_load for pata_via.  This patch cleans it up a bit.

* Instead of duplicating whole body, copy tf and set ATA_TFLAG_DEVICE
  when necessary.

* Rename via_ata_tf_load() to via_tf_load().

* No need to set .tf_load in via_port_ops_noirq as it inherits from
  via_port_ops.

* Clean up indentation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Save SControl during probing and restore it on detach.  This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).

It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill.  For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

SError belongs to link not port.  Use ata_link_printk() to print it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

As an optimization, follow-up SRST used to be skipped if
classification wasn't requested even when hardreset requested it via
-EAGAIN.  However, some hardresets can't wait for device readiness and
skipping SRST can cause timeout or other failures during revalidation.
Always perform follow-up SRST if hardreset returns -EAGAIN.  This
makes reset paths more predictable and thus less error-prone.

While at it, move hardreset error checking such that it's done right
after hardreset is finished.  This simplifies followup SRST condition
check a bit and makes the reset path easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ehc->i.action got accidentally overwritten to ATA_EH_HARD/SOFTRESET in
ata_eh_reset().  The original intention was to clear reset action
which wasn't selected.  This can cause unexpected behavior when other
EH actions are scheduled together with reset.  Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

The SoC sata port is based on the 7042/6042 devices (Gen IIE). This patch
will fix various issues when working with PMP and/or NCQ.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

This patch adds the Intel Ibex Peak (PCH) IDE mode SATA Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Resend with proper whitespace.

This patch adds the Intel Ibex Peak (PCH) SATA RAID Controller DeviceIDs.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sata_mv allowed issuing two DMA commands concurrently which the
hardware allows.  Unfortunately, libata core layer isn't ready for
this yet and spews ugly warning message and malfunctions on this.
Don't allow concurrent DMA commands for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Implement force params nohrst, nosrst and norst.  This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5212/1: pxa: fix build error when CPU_PXA310 is not defined
  [ARM] 5208/1: fsg-setup.c fixes
  [ARM] fix impd1.c build warning
  [ARM] e400 config use MFP
  [ARM] e740 config use MFP
  [ARM] Fix eseries IRQ limit
  [ARM] clocklib: Update users of aliases to new API
  [ARM] clocklib: Allow dynamic alias creation
  [ARM] eseries: whitespace fixes and cleanup

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  pnp: fix "add acpi:* modalias entries"
  UIO: generic irq handling for some uio platform devices
  UIO: uio_pdrv: fix license specification
  UIO: uio_pdrv: fix memory leak
  block: drop references taken by class_find_device()
  block: fix partial read() of /proc/{partitions,diskstats}
  PM: Remove WARN_ON from device_pm_add
  driver core: add init_name to struct device
  PM: don't skip device PM init when CONFIG_PM_SLEEP isn't set and CONFIG_PM is set
  driver model: anti-oopsing medicine
  dev_printk(): constify the `dev' argument
  drivers/base/driver.c: remove unused to_dev() macro
  Documentation: HOWTO-ja_JP-sync patch
  Japanese translation of Documentation/SubmitChecklist
  kobject: Replace ALL occurrences of '/' with '!' instead of only the first one.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
  USB: automatically enable RHSC interrupts
  USB: Don't rebind before "complete" callback
  USB: Add new PM callback methods for USB
  USB: Defer Set-Interface for suspended devices
  USB: Add udev argument to interface suspend/resume functions
  USB: cdc-acm: don't unlock acm->mutex on error path
  MUSB: Fix index register corruption seen with g_ether and Windows host
  usb: musb: get rid of MUSB_LOGLEVEL and use parameter
  usb: musb: get rid of procfs entry
  USB: Fix pxa27x_udc usb speed handling.
  USB: cdc-acm: quirk for Conexant CX93010 USB modem
  USB: fix bug in usb_unlink_anchored_urbs()
  usb-serial: option support HSDPA modem A2502
  USB: ISP1760: fixed trivial math in comment

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Concurrently adding the same segment may lead to duplicate device_register()
calls, which will trigger an error in kobject code:
"... don't try to register things with the same name in the same directory".
This patch adds a check to avoid this.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Calling a ccw driver's notify function without the ccw device lock
held opens up a race window between discovery and handling of a change
in the device operational state. As a result, the device driver may
encounter unexpected device malfunction, leading to out-of-retry
situations or similar.

Remove race by extending the ccw device lock from state change
discovery to the calling of the notify function.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

The Perform Subsystem Function/Prepare for Read Subsystem Data
command requires 12 bytes of parameter data, but the respective data
structure dasd_psf_prssd_data has a length of 16 bytes.
Current storage servers ignore the obsolete bytes, but older models
fail to execute the command and report an incorrect length error.
This causes the device initilization for these devices to fail.
To fix this problem we need to correct the dasd_psf_prssd_data
structure and shorten it to the correct length.
Reported-by: Ivan Warren <ivan@vmfacility.fr>
Reviewed-by: Ivan Warren <ivan@vmfacility.fr>
Tested-by: Ivan Warren <ivan@vmfacility.fr>
CC: stable <stable@kernel.org>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>

ext4 does not work on s390 because ext2_find_next_bit is broken. Fortunately
this function is only used by ext4. The function uses ffs which does not work
analog to ffz. The result of ffs has an offset of 1 which is not taken into
account. To fix this use the low level __ffs_word function directly instead
of the ill defined ffs.

In addition the patch improves find_next_zero_bit and ext2_find_next_zero_bit
by passing the bit offset into __ffz_word instead of adding it after the
function call returned.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Fix ccw group device initialization: initialize device object before
using reference counting during cleanup.

Fixes the following message when group device initialization fails
(e.g. because too few devices where specified):

  kobject: '<NULL>' (..): is not initialized, yet kobject_put() is
           being called.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Increasing the qdio reference count for every used subchannel
is unnecessary since unloading qdio (if build as a module) is
only possible if other modules that use qdio are unloaded.
Unloading modules that use qdio in turn requires that these
modules shut down all qdio subchannels. Therefore the additional
module_get reference is not needed.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Improve s390 debug feature usage:
- log busy bit in dbf
- increase size of dbf views
- consistent logging of qdio api calls to setup view
- print subchannel number so one can associate the interface
  with the dbf data
- only log events to one view
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

If qdio_establish fails we call qdio_shutdown to cleanup the
qdio subchannel. The tiq_list entry may not be valid at that
time, therefore we must ignore queues with an invalid list entry
in tiqdio_remove_input_queues.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Remove the now unneeded s390_idle.lock spinlock initialization after
Josef Sipek did it the right way in arch/s390/kernel/process.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Ever since commit 43ca5c3a ([S390] Convert
monitor calls to function calls.), the kernel refused to IPL with spinlock
debugging enabled.

BUG: spinlock bad magic on CPU#0, swapper/0
 lock: 00000000003a4668, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 Not tainted 2.6.25 #1
Process swapper (pid: 0, task: 000000000034f958, ksp: 0000000000377d60)
0000000000377ab8 0000000000352628 0000000000377d60 0000000000377d60
       0000000000016af4 00000000fffff7b5 0000000000377d60 0000000000000000
       0000000000000000 0000000000377a18 0000000000000009 0000000000377a18
       0000000000377a78 000000000023c920 0000000000016af4 0000000000377a18
       0000000000000005 0000000000000000 0000000000377b58 0000000000377ab8
Call Trace:
([<0000000000016a60>] show_trace+0xdc/0x108)
 [<0000000000016b4e>] show_stack+0xc2/0xfc
 [<0000000000016c9a>] dump_stack+0xb2/0xc0
 [<0000000000172dd4>]
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

In case of error, functions dasd_kmalloc_request and idal_buffer_alloc
return an ERR pointer, but never return the NULL pointer. So after a
call to one of these functions, a NULL test should be replaced by an
IS_ERR test.

A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x =
(
  dasd_kmalloc_request(...)
|
  idal_buffer_alloc(...)
)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
 )
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.

usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: USB2VGA dongle found at address 4
usb 1-2: Allocated 8 output buffers
usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32
usb 1-2: New USB device found, idVendor=0711, idProduct=0918
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Signed-off-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled.  Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub.  This approach turns out to be subject to races, resulting
in unnecessary polling.

The patch does away with the method entirely.  Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present.  This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management.  We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support.  Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.

The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON.  Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.

This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.

A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure.  This way they will be invoked only for USB devices, not
for USB interfaces.  The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1128) fixes one of the problems related to the new PM
infrastructure.  We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.

The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed.  Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines.  Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.

It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

On Wed, Jul 23, 2008 at 03:52:36PM +0300, Andrei Popa wrote:
> I installed gnokii-0.6.22-r2 and gave the command "gnokii --identify"
> and the kernel oopsed:
>
> BUG: unable to handle kernel NULL pointer dereference at 00000458
> IP: [<c0444b52>] mutex_unlock+0x0/0xb
>  [<c03830ae>] acm_tty_open+0x4c/0x214
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Tested-by: Andrei Popa <andrei.popa@i-neo.ro>
Cc: stable <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If Indexed Mode register accesses are enabled, the ep0_rxstate()
function calls musb_g_ep0_giveback() before writing to the CSR
register. When control returns to this ep0_rxstate, the index
register contents are over-written. This causes the CSR register
write to fail.

Fixed by writing the correct value into the index register before
writing to the CSR.

This was observed only in ep0_rxstate() with g_ether loaded and
the device connected to a MS Windows host PC. Anticipatively fixed
ep0_txstate() as well.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.

We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.

Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.

Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>