- 20 Jul, 2013 2 commits
-
-
Chris Wilson authored
In theory, the different register blocks were meant to be only ever touched when holding either the struct_mutex, mode_config.lock or even a specific localised lock. This does not seem to be the case, and the hardware reacts extremely badly if we attempt to concurrently access two registers within the same cacheline. The HSD suggests that we only need to do this workaround for display range registers. However, upon review we need to serialize the multiple stages in our register write functions - if only for preemption protection. Irrespective of the hardware requirements, the current io functions are a little too loose with respect to the combination of pre- and post-condition testing that we do in conjunction with the actual io. As a result, we may be pre-empted and generate both false-postive and false-negative errors. Note well that this is a "90%" solution, there remains a few direct users of ioread/iowrite which will be fixed up in the next few patches. Since they are more invasive and that this simple change will prevent almost all lockups on Haswell, we kept this patch simple to facilitate backporting to stable. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63914Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Kamal Mostafa authored
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=47941 BugLink: https://bugs.launchpad.net/bugs/1163720 BugLink: https://bugs.launchpad.net/bugs/1162026 Some machines suffer from non-functional backlight controls if BLM_PCH_PWM_ENABLE is set, so provide a quirk to avoid doing so. Apply this quirk to Dell XPS 13 models. Tested-by:
Eric Griffith <EGriffith92@gmail.com> Tested-by:
Kent Baxley <kent.baxley@canonical.com> Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
-
- 18 Jul, 2013 2 commits
-
-
Daniel Vetter authored
To avoid stalls we delay tiling changes and especially hold of committing the new fence state for as long as possible. Synchronization points are in the execbuf code and in our gtt fault handler. Unfortunately we've missed that tricky detail when adding proper fence restore code in commit 19b2dbde Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Jun 12 10:15:12 2013 +0100 drm/i915: Restore fences after resume and GPU resets The result was that we've restored fences for objects with no tiling, since the object<->fence link still existed after resume. Now that wouldn't have been too bad since any subsequent access would have fixed things up, but if we've changed from tiled to untiled real havoc happened: The tiling stride is stored -1 in the fence register, so a stride of 0 resulted in all 1s in the top 32bits, and so a completely bogus fence spanning everything from the start of the object to the top of the GTT. The tell-tale in the register dumps looks like: FENCE START 2: 0x0214d001 FENCE END 2: 0xfffff3ff Bit 11 isn't set since the hw doesn't store it, even when writing all 1s (at least on my snb here). To prevent such a gaffle in the future add a sanity check for fences with an untiled object attached in i915_gem_write_fence. v2: Fix the WARN, spotted by Chris. v3: Trying to reuse get_fences looked ugly and obfuscated the code. Instead reuse update_fence and to make it really dtrt also move the fence dirty state clearing into update_fence. Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Stéphane Marchesin <marcheu@chromium.org> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60530 Cc: stable@vger.kernel.org (for 3.10 only) Reviewed-by:
Matthew Garrett <matthew.garrett@nebula.com> Tested-by:
Björn Bidar <theodorstormgrade@gmail.com> Signed-off-by:
-
Daniel Vetter authored
Backmerge Linux 3.10 to get at commit 19b2dbde Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed Jun 12 10:15:12 2013 +0100 drm/i915: Restore fences after resume and GPU resets That commit is not in my current -fixes pile since that's based on my -next queue for 3.11. And the above mentioned fix was merged really late into 3.10 (and blew up, bad me) so was on a diverging branch. Option B would have been to rebase my current pile of fixes onto Dave's drm-fixes branch. But since some of the patches here are a bit tricky I've decided not to void all the testing by moving over the entire merge window. Signed-off-by:
-
- 17 Jul, 2013 3 commits
-
-
Chris Wilson authored
In commit e3de42b6 Author: Imre Deak <imre.deak@intel.com> Date: Fri May 3 19:44:07 2013 +0200 drm/i915: force full modeset if the connector is in DPMS OFF mode a new function was added that walked over the set of connectors to see if any of the currently associated CRTC was switched off. This function walked an array of connectors, rather than the array of pointers to connectors contained in the drm_mode_set - i.e. it was dereferencing far past the end of the first connector. This only becomes an issue if we attempt to use a clone mode (i.e. more than one connector per CRTC) such that set->num_connectors > 1. Reported-by:
Timo Aaltonen <tjaalton@ubuntu.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65927Signed-off-by:
-
Daniel Vetter authored
There seems to be no limit to the amount of gunk the firmware can leave behind. Some platforms leave pch dplls on which are not in active use at all. The example in the bug report is a Apple Macbook Pro. Note that this escape scrunity of the hw state checker until we've tried to use this enabled, but unused pll since we did only check for the inverse case of a in-used, but disabled pll. v2: Add a WARN in the pll state checker which would have caught this case. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66952Reported-and-tested-by:
shui yangwei <yangweix.shui@intel.com> Reviewed-by:
-
Konstantin Khlebnikov authored
This patch fixes regression in power consumtion of sandy bridge gpu, which exists since v3.6 Sometimes after resuming from s2ram gpu starts thinking that it's extremely busy. After that it never reaches rc6 state. Bug exists since kernel v3.6: commit b4ae3f22 Author: Jesse Barnes <jbarnes@virtuousgeek.org> Date: Thu Jun 14 11:04:48 2012 -0700 drm/i915: load boot context at driver init time For some reason RC6 is already enabled at the beginning of resuming process. Following initliaztion breaks some internal state and confuses RPS engine. This patch disables RC6 at the beginnig of resume and initialization. I've rearranged initialization sequence, because intel_disable_gt_powersave() needs initialized force_wake_get/put and some locks from the dev_priv. Note: The culprit in the initialization sequence seems to be the write to MBCTL added in the above mentioned commit. The first version of this patch just held a forcewake reference across the clock gating init functions, which seems to have been enought to gather quite a few positive test reports. But since that smelled a bit like ad-hoc duct-tape v2 now just disables rps/rc6 across the entire hw setup. References: https://bugs.freedesktop.org/show_bug.cgi?id=54089 References: https://bugzilla.kernel.org/show_bug.cgi?id=58971 References: https://patchwork.kernel.org/patch/2827634/ (patch v1) Signed-off-by:
Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> [danvet: Add note about v1 vs. v2 of this patch and use standard layout for the commit citation. Also add the tested-bys from v1 and a cc: stable.] Cc: stable@vger.kernel.org (Note: tiny conflict due to the addition of the backlight lock in 3.11) Tested-by: Alexander Kaltsas <alexkaltsas@gmail.com> (v1) Tested-by: rocko <rockorequin@hotmail.com> (v1) Tested-by: JohnMB <johnmbryant@sky.com> (v1) Signed-off-by:
-
- 13 Jul, 2013 1 commit
-
-
Stéphane Marchesin authored
Otherwise the DDI_A_4_LANES bit gets lost and we can't use > 2 lanes on eDP. This fixes eDP on hsw with > 2 lanes. Also s/port_reversal/saved_port_bits/ since the current name is confusing. Signed-off-by:
Stéphane Marchesin <marcheu@chromium.org> Reviewed-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
-
- 12 Jul, 2013 1 commit
-
-
Daniel Vetter authored
I.e. for letter/pillarboxing. For those cases we need to adjust the mode a bit, but Jesse gmch pfit refactoring in commit 2dd24552 Author: Jesse Barnes <jbarnes@virtuousgeek.org> Date: Thu Apr 25 12:55:01 2013 -0700 drm/i915: factor out GMCH panel fitting code and use for eDP v3 broke that by reordering the computation of the gmch pfit state with the block of code that prepared the adjusted mode for it and told the modeset core not to overwrite the adjusted mode with default settings. We might want to switch around the core code to just fill in defaults, but this code predates the pipe_config modeset rework. And in the old crtc helpers we did not have a suitable spot to do this. Cc: Mika Kuoppala <mika.kuoppala@intel.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Hans de Bruin <jmdebruin@xmsnet.nl> Reported-and-tested-by:
Hans de Bruin <jmdebruin@xmsnet.nl> Reviewed-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
- 11 Jul, 2013 1 commit
-
-
Daniel Vetter authored
It's in the PFIT_CONTROL register, but very much associated with the lvds encoder. So move the readout for it (in the case of an otherwise disabled pfit) from the pipe to the lvds encoder's get_config function. Otherwise we get a pipe state mismatch if we use pipe B for a non-lvds output and we've left the dither bit enabled behind us. This can happen if the BIOS has set the bit (some seem to unconditionally do that, even in the complete absence of an lvds port), but not enabled pipe B at boot-up. Then we won't clear the pfit control register since we can only touch that if the pfit is associated with our pipe in the crtc configuration - we could trample over the pfit state of the other pipe otherwise since it's shared. Once pipe B is enabled we notice that the 6to8 dither bit is set and complain about the mismatch. Note that testing indicates that we don't actually need to set this bit when the pfit is disabled, dithering on 18bpp panels seems to work regardless. But ripping that code out is not something for a bugfix meant for -rc kernels. v2: While at it clarify the logic in i9xx_get_pfit_config, spurred by comments from Chris on irc. v3: Use Chris suggestion to make the control flow in i9xx_get_pfit_config easier to understand. v4: Kill the extra line, spotted by Chris. Reported-by:
Knut Petersen <Knut_Petersen@t-online.de> Cc: Knut Petersen <Knut_Petersen@t-online.de> Cc: Chris Wilson <chris@chris-wilson.co.uk> References: http://lists.freedesktop.org/archives/intel-gfx/2013-July/030092.htmlTested-by:
-
- 10 Jul, 2013 4 commits
-
-
Chris Wilson authored
This reverts commit 25ff1195 and the follow on for Valleyview commit 2dc8aae0. commit 25ff1195 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Apr 4 21:31:03 2013 +0100 drm/i915: Workaround incoherence between fences and LLC across multiple CPUs commit 2dc8aae0 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Wed May 22 17:08:06 2013 +0100 drm/i915: Workaround incoherence with fence updates on Valleyview Jon Bloomfield came up with a plausible explanation and cheap fix (drm/i915: Fix incoherence with fence updates on Sandybridge+) for the race condition, so lets run with it. This is a candidate for stable as the old workaround incurs a significant cost (calling wbinvd on all CPUs before performing the register write) for some workloads as noted by Carsten Emde. Link: http://lists.freedesktop.org/archives/intel-gfx/2013-June/028819.html References: https://www.osadl.org/?id=1543#c7602 References: https://bugs.freedesktop.org/show_bug.cgi?id=63825Signed-off-by:
-
Chris Wilson authored
This hopefully fixes the root cause behind the workaround added in commit 25ff1195 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Apr 4 21:31:03 2013 +0100 drm/i915: Workaround incoherence between fences and LLC across multiple CPUs Thanks to further investigation by Jon Bloomfield, he realised that the 64-bit register might be broken up by the hardware into two 32-bit writes (a problem we have encountered elsewhere). This non-atomicity would then cause an issue where a second thread would see an intermediate register state (new high dword, old low dword), and this register would randomly be used in preference to its own thread register. This would cause the second thread to read from and write into a fairly random tiled location. Breaking the operation into 3 explicit 32-bit updates (first disable the fence, poke the upper bits, then poke the lower bits and enable) ensures that, given proper serialisation between the 32-bit register write and the memory transfer, that the fence value is always consistent. Armed with this knowledge, we can explain how the previous workaround work. The key to the corruption is that a second thread sees an erroneous fence register that conflicts and overrides its own. By serialising the fence update across all CPUs, we have a small window where no GTT access is occurring and so hide the potential corruption. This also leads to the conclusion that the earlier workaround was incomplete. v2: Be overly paranoid about the order in which fence updates become visible to the GPU to make really sure that we turn the fence off before doing the update, and then only switch the fence on afterwards. Signed-off-by:
Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by:
-
Chris Wilson authored
Daniel noticed a problem where is we wrote to an object with ring A in the middle of a very long running batch, then executed a quick batch on ring B before a batch that reads from the same object, its obj->ring would now point to ring B, but its last_write_seqno would be still relative to ring A. This would allow for the user to read from the object before the GPU had completed the write, as set_domain would only check that ring B had passed the last_write_seqno. To fix this simply (and inelegantly), we bump the last_write_seqno when switching rings so that the last_write_seqno is always relative to the current obj->ring. This fixes igt/tests/gem_write_read_ring_switch. Signed-off-by:
-
Guenter Roeck authored
This patch partially reverts commit 36ec8f87 for IvyBridge CPUs. The original commit results in repeated 'Timed out waiting for forcewake old ack to clear' messages on a Supermicro C7H61 board (BIOS version 2.00 and 2.00b) with i7-3770K CPU. It ultimately results in a hangup if the system is highly loaded. Reverting the commit for IvyBridge CPUs fixes the issue. Issue a warning if the CPU is IvyBridge and mt forcewake is disabled, since this condition can result in secondary issues. v2: Only revert patch for Ivybridge CPUs Issue info message if mt forcewake is disabled on Ivybridge Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60541 Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66139Signed-off-by:
-
- 09 Jul, 2013 4 commits
-
-
Imre Deak authored
DP 1.2 compatible displays may report a 5.4Gbps maximum bandwidth which the driver will treat as an invalid value and use 1.62Gbps instead. Fix this by capping to 2.7Gbps for sinks reporting a 5.4Gbps max bw. Also add a warning for reserved values. v2: - allow only bw values explicitly listed in the DP standard (Daniel, Chris) Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
-
Daniel Vetter authored
It's not a good idea to also run the pipe_control cleanup. This regression has been introduced whith the original cs tlb w/a in commit b45305fc Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Mon Dec 17 16:21:27 2012 +0100 drm/i915: Implement workaround for broken CS tlb on i830/845 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64610 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@vger.kernel.org Reviewed-by:
-
Xiong Zhang authored
obj->mm_list link to dev_priv->mm.inactive_list/active_list obj->global_list link to dev_priv->mm.unbound_list/bound_list This regression has been introduced in commit 93927ca5 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Jan 10 18:03:00 2013 +0100 drm/i915: Revert shrinker changes from "Track unbound pages" Cc: stable@vger.kernel.org Signed-off-by:
Xiong Zhang <xiong.y.zhang@intel.com> [danvet: Add regression notice.] Signed-off-by:
-
Paulo Zanoni authored
Now that the audio driver is using our power well API, everything should be working correctly, so let's give it a try. Signed-off-by:
-
- 04 Jul, 2013 1 commit
-
-
Daniel Vetter authored
This fixes gpu reset on my gm45 - without this patch the bsd thing is forever stuck since the seqno updates never reach the status page. Tbh I have no idea how this ever worked without rewriting the hws registers after a gpu reset. To satisfy my OCD also give the functions a bit more consistent names: - Use status_page everywhere, also for the physical addressed one. - Use init for the allocation part and setup for the register setup part consistently. Long term I'd really like to share the hw init parts completely between gpu reset, resume and driver load, i.e. to call i915_gem_init_hw instead of the individual pieces we might need. v2: Add the missing paragraph to the commit message about what bug exactly this patch here fixes. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65495 Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
lu hua <huax.lu@intel.com> Signed-off-by:
-
- 02 Jul, 2013 1 commit
-
-
Daniel Vetter authored
Every other place properly checks whether we've managed to set up the stolen allocator at boot-up properly, with the exception of the cleanup code. Which results in an ugly *ERROR* Memory manager not clean. Delaying takedown at module unload time since the drm_mm isn't initialized at all. v2: While at it check whether the stolen drm_mm is initialized instead of the more obscure stolen_base == 0 check. v3: Fix up the logic. Also we need to keep the stolen_base check in i915_gem_object_create_stolen_for_preallocated since that can be called before stolen memory is fully set up. Spotted by Chris Wilson. v4: Readd the conversion in i915_gem_object_create_stolen_for_preallocated, the check is for the dev_priv->mm.gtt_space drm_mm, the stolen allocatot must already be initialized when calling that function (if we indeed have stolen memory). Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65953 Cc: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: lu hua <huax.lu@intel.com> (v3) Reviewed-by:
-
- 01 Jul, 2013 20 commits
-
-
Chris Wilson authored
So it appears that I have encountered some bogosity when trying to call i915_error_printf() with many arguments from print_error_buffers(). The symptom is that the vsnprintf parser tries to interpret an integer arg as a character string, the resulting OOPS indicating stack corruption. Replacing the single call with its 13 format specifiers and arguments with multiple calls to i915_error_printf() worked fine. This patch goes one step further and introduced i915_error_puts() to pass the strings simply. It may not fix the root cause, but it does prevent my box from dying and I think helps make print_error_buffers() more friendly. Signed-off-by:
-
Chris Wilson authored
Harmonise the completion logic between the non-blocking and normal wait_rendering paths, and move that logic into a common function. In the process, we note that the last_write_seqno is by definition the earlier of the two read/write seqnos and so all successful waits will have passed the last_write_seqno. Therefore we can unconditionally clear the write seqno and its domains in the completion logic. v2: Add the missing ring parameter, because sometimes it is good to have things compile. Signed-off-by:
-
Chris Wilson authored
In the introduction of the non-blocking wait, I cut'n'pasted the wait completion code from normal locked path. Unfortunately, this neglected that the normal path returned early if the wait returned early. The result is that read-only waits may return whilst the GPU is still writing to the bo. Fixes regression from commit 3236f57a [v3.7] Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Fri Aug 24 09:35:09 2012 +0100 drm/i915: Use a non-blocking wait for set-to-domain ioctl Signed-off-by:
-
Xiong Zhang authored
On DevCPT, the control register for Transcoder DP Sync Polarity is TRANS_DP_CTL, not DP_CTL. Without this patch, Many call trace occur on CPT machine with DP monitor. The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X) v2: use intel-crtc to simple patch, suggested by Daniel. Signed-off-by:
-
Daniel Vetter authored
Our interrupt handler (in hardirq context) could race with the timer (in softirq context), hence we need to hold the spinlock around the call to ->hdp_irq_setup in intel_hpd_irq_handler, too. But as an optimization (and more so to clarify things) we don't need to do the irqsave/restore dance in the hardirq context. Note also that on ilk+ the race isn't just against the hotplug reenable timer, but also against the fifo underrun reporting. That one also modifies the SDEIMR register (again protected by the same dev_priv->irq_lock). To lock things down again sprinkle a assert_spin_locked. But exclude the functions touching SDEIMR for now, I want to extract them all into a new helper function (like we do already for pipestate, display interrupts and all the various gt interrupts). v2: Add the missing 't' Egbert spotted in a comment. v3: Actually fix the right misspelled comment (Paulo). Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
The usual pattern for our sub-function irq_handlers is that they check for the no-irq case themselves. This results in more streamlined code in the upper irq handlers. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
Everywhere the same. Note that this patch leaves unnecessary braces behind, but the next patch will kill those all anyway (including the if itself) so I've figured I can keep the diff a bit smaller. v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
We already have a vfunc for this (and other parts of the hpd storm handling code already use it). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
The combination of Paulo's fifo underrun detection code and Egbert's hpd storm handling code unfortunately made the hpd storm handling code racy. To avoid duplicating tricky interrupt locking code over all platforms start with a bit of refactoring. This patch is the very first step since in the end the irq storm handling code will handle all hotplug logic (and so also encapsulate the locking nicely). v2: Rebase on top of the i965g/gm sdvo hpd fix. Cc: Egbert Eich <eich@suse.de> Reviewed-by:
-
Daniel Vetter authored
By the time we write DEIER in the postinstall hook the interrupt handler could run any time. And it does modify DEIER to handle interrupts. Hence the DEIER read-modify-write cycle for enabling the PCU event source is racy. Close this races the same way we handle vblank interrupts: Unconditionally enable the interrupt in the IER register, but conditionally mask it in IMR. The later poses no such race since the interrupt handler does not touch DEIMR. Also update the comment, the clearing has already happened unconditionally above. v2: Actually shove the updated comment into the right train^W commit, as spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
-
Daniel Vetter authored
The haswell unclaimed register handling code forgot to take the spinlock. Since this is in the context of the non-rentrant interupt handler and we only have one interrupt handler it is sufficient to just grab the spinlock - we do not need to exclude any other interrupts from running on the same cpu. To prevent such gaffles in the future sprinkle assert_spin_locked over these functions. Unfornately this requires us to hold the spinlock in the ironlake postinstall hook where it is not strictly required: Currently that is run in single-threaded context and with userspace exlcuded from running concurrent ioctls. Add a comment explaining this. v2: ivb_can_enable_err_int also needs to be protected by the spinlock. To ensure this won't happen in the future again also sprinkle a spinlock assert in there. v3: Kill the 2nd call to ivb_can_enable_err_int I've accidentally left behind, spotted by Paulo. Cc: Paulo Zanoni <przanoni@gmail.com> Reviewed-by:
Paulo Zanoni <przanoni@gmail.com> Signed-off-by:
-
Ben Widawsky authored
With updates to the spec, we can actually see the context layout, and how many dwords are allocated. That table suggests we need 70720 bytes per HW context. Rounded up, this is 18 pages. Looking at what lives after the current 4 pages we use, I can't see too much important (mostly it's d3d related), but there are a couple of things which look scary. I am hopeful this can explain some of our odd HSW failures. v2: Make the context only 17 pages. The power context space isn't used ever, and execlists aren't used in our driver, making the actual total 66944 bytes. v3: Add a comment to the code. (Jesse & Paulo) Reported-by:
"Azad, Vinit" <vinit.azad@intel.com> Cc: stable@vger.kernel.org Reviewed-by:
Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Ville Syrjälä authored
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which caused the sprites to not work at all. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
-
Ville Syrjälä authored
The PIPECONF color range bit doesn't appear to be effective, on HDMI outputs at least. The color range bit in the port register works though, so let's use it. I have not yet verified whether the PIPECONF bit works on DP outputs. This reverts commit 83a2af88. Signed-off-by:
-
Ville Syrjälä authored
LPF is short for "low pass filter". Signed-off-by:
-
Ville Syrjälä authored
The current PLL settings produce a rather unstable picture when I hook up a VLV to my HP ZR24w display via a VGA cable. According to VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9, we should use the the same LPF coefficients for DAC as we do for HDMI and RBR DP. And indeed that seems to cure the shivers. v2: Add the name of the relevant document to the commit message Signed-off-by:
-
Ville Syrjälä authored
If the current GPU frquency is below RPe, and we're asked to increase it, just go directly to RPe. This should provide better performance faster than letting the frequency trickle up in response to the up threshold interrupts. For now just do it for VLV, since that matches quite closely how VLV used to operate when the rps delayed timer kept things at RPe always. Signed-off-by:
-
Ville Syrjälä authored
There's little point in increasing the GPU frequency from the delayed rps work on VLV. Now when the GPU is idle, the GPU frequency actually keeps dropping gradually until it hits the minimum, whereas previously it just ping-ponged constantly between RPe and RPe-1. Signed-off-by:
-
Ville Syrjälä authored
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs. Reading it always returns zero from what I can tell, and eliminating it doesn't seem to make any difference to the behaviour of the system. Signed-off-by:
-
Ville Syrjälä authored
Eliminate the weird inverted logic from the rps new_delay comparison. Signed-off-by:
-
