- 09 Aug, 2010 6 commits
-
-
John W. Linville authored
CC [M] drivers/net/wireless/libertas/cfg.o /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_scan_worker’: /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: ‘TASK_NORMAL’ undeclared (first use in this function) /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.) /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c: In function ‘lbs_cfg_connect’: /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function) /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘signal_pending’ /home/greearb/git/wireless-testing/drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function ‘schedule_timeout’ Reported-by:
Ben Greear <greearb@candelatech.com> Reported-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
John W. Linville authored
This reverts commit 5f7aebd8. Apparently, that PCI ID data was incorrectly taken from the subsystem information. The actual ID matches another already known ID. Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Jeff Kirsher authored
Adds documentation for the igbvf (igb virtual function driver). v2: - Removed trailing white space - Removed Ethtool version info Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jeff Kirsher authored
Add documentation for the igb networking driver. v2: - Removed trailing white space - Removed Ethtool version info - Removed LRO kernel version info Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jeff Kirsher authored
Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
John Fastabend authored
Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause a build error. This resolves the build error by wrapping the fcoe.up in CONFIG_IXGBE_DCB ifdefs. Also frames were being priority VLAN tagged even without DCB enabled. This fixes this so that 8021Q priority tags are only added with DCB actually enabled. Reported-by:
divya <dipraksh@linux.vnet.ibm.com> Reported-by:
Jon Mason <jon.mason@exar.com> Signed-off-by:
John Fastabend <john.r.fastabend@intel.com> Tested-by:
Stephen Ko <stephen.s.ko@intel.com> Tested-by:
Ross Brattain <ross.b.brattain@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 08 Aug, 2010 7 commits
-
-
Amit Kumar Salecha authored
Signed-off-by:
Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
I moved the kfree(cb) below the dereferences. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
We should unlock here. This is the only place where we return from the function with the lock held. The caller isn't expecting it. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Woodhouse authored
We were seeing faults in the solos-pci receive tasklet when packets arrived for a VCC which was currently being closed: [18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14 [18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1 [18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684] [18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci] [18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci] [18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48 [18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57 [18845.274437] [<c1025720>] tasklet_action+0x42/0x69 [18845.303247] [<c102643f>] __do_softirq+0x8e/0x129 [18845.331540] [<c10264ff>] do_softirq+0x25/0x2a [18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a [18845.389677] [<c102666d>] local_bh_enable+0xb/0xe [18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic] [18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox] This patch uses an RCU-inspired approach to fix it. In the RX tasklet's find_vcc() function we first refuse to use a VCC which already has the ATM_VF_READY bit cleared. And in the VCC close function, we synchronise with the tasklet to ensure that it can't still be using the VCC before we continue and allow the VCC to be destroyed. Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Tested-by:
Nathan Williams <nathan@traverse.com.au> Cc: stable@kernel.org Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jarek Poplawski authored
Since there was added ->tcf_chain() method without ->bind_tcf() to sch_sfq class options, there is oops when a filter is added with the classid parameter. Fixes commit 7d2681a6 netdev thread: null pointer at cls_api.c Signed-off-by:
Jarek Poplawski <jarkao2@gmail.com> Reported-by:
Franchoze Eric <franchoze@yandex.ru> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
Although netif_rx() isn't expected to be called in process context with preemption enabled, it'd better handle this case. And this is why get_cpu() is used in the non-RPS #ifdef branch. If tree RCU is selected, rcu_read_lock() won't disable preemption, so preempt_disable() should be called explictly. Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dmitry Popov authored
tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG) length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16 bytes long. Signed-off-by:
Dmitry Popov <dp@highloadlab.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 06 Aug, 2010 3 commits
-
-
Johannes Berg authored
spin_is_locked() can return zero on some (UP?) configurations because locks don't exist, and that causes an endless amount of warnings. Use lockdep_assert_held() instead, which has two advantages: 1) it verifies the current task is holding the lock or mutex 2) it compiles away completely when lockdep is not enabled Cc: stable@kernel.org [2.6.34+, maybe only parts of patch] Reported-by:
Thomas Meyer <thomas@m3y3r.de> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Johannes Berg authored
The TX tracing code copies with the wrong length, which will typically copy too little data. Fix this by using the correct length variable. Cc: stable@kernel.org [2.6.32+] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
- 05 Aug, 2010 17 commits
-
-
Dan Carpenter authored
The main motivation of this patch changing strcpy() to strlcpy(). We strcpy() to copy a 48 byte buffers into a 49 byte buffers. So at best the last byte has leaked information, or maybe there is an overflow? Anyway, this patch closes the information leaks by zeroing the memory and the calls to strlcpy() prevent overflows. Signed-off-by:
Dan Carpenter <error27@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jarek Poplawski authored
The netpoll_rx_on() check in __napi_gro_receive() skips part of the "common" GRO_NORMAL path, especially "pull:" in dev_gro_receive(), where at least eth header should be copied for entirely paged skbs. Signed-off-by:
Jarek Poplawski <jarkao2@gmail.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Christian Samsel authored
With turned on hspa modem (Dell 5530 internal card) and activated usb auto suspend, my system gets up 100 "usbnet_resume has delayed data" per minute. I didnt noticed any pathological behaviour, so just drop this message. if any objections, please at least change it to _DEBUG. Signed-off-by:
Christian Samsel <christian.samsel@rwth-aachen.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
John W. Linville authored
ieee80211_beacon_get can return NULL... Signed-off-by:
John W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org
-
Sujith authored
So long. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Dan Williams authored
Fix this leftover TODO from the cfg80211 conversion by doing a scan if cfg80211 didn't pass in the BSSID for us. Since the scan code uses so much of the cfg80211_scan_request structure to build up the firmware command, we just fake one when the scan request is triggered internally. But we need to make sure that internal 'fake' cfg82011 scan request does not get back to cfg82011 via cfg80211_scan_done(). Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Dan Williams authored
Some APs get pissy if you don't send the firmware the extended rates in the association request's rates TLV. Found this on a Linksys WRT54G v2; it denies association with status code 18 unless you add the extended rates too. The old driver did this, but it got lost in the cfg80211 conversion. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Dan Williams authored
Let's actually check the right field in the command response; and if there aren't any reported BSSes, exit early with success. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Rusty Russell authored
I often use "ethtool -i" command to check what driver controls the ehternet device. But because current virtio_net driver doesn't support "ethtool -i", it becomes the following: # ethtool -i eth3 Cannot get driver information: Operation not supported This patch simply adds the "ethtool -i" support. The following is the result when using the virtio_net driver with my patch applied to. # ethtool -i eth3 driver: virtio_net version: N/A firmware-version: N/A bus-info: virtio0 Personally, "-i" is one of the most frequently-used option, and most network drivers support "ethtool -i", so I think virtio_net also should do. Signed-off-by:
Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use ARRAY_SIZE) Signed-off-by:
David S. Miller <davem@davemloft.net>
-
stephen hemminger authored
The PPP channel ops structure should be const. Cleanup the declarations to use standard C99 format. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Howells authored
RxRPC can potentially deadlock as rxrpc_resend_time_expired() wants to get call->state_lock so that it can alter the state of an RxRPC call. However, its caller (call_timer_fn()) has an apparent lock on the timer struct. The problem is that rxrpc_resend_time_expired() isn't permitted to lock call->state_lock as this could cause a deadlock against rxrpc_send_abort() as that takes state_lock and then attempts to delete the resend timer by calling del_timer_sync(). The deadlock can occur because del_timer_sync() will sit there forever waiting for rxrpc_resend_time_expired() to return, but the latter may then wait for call->state_lock, which rxrpc_send_abort() holds around del_timer_sync()... This leads to a warning appearing in the kernel log that looks something like the attached. It should be sufficient to simply dispense with the locks. It doesn't matter if we set the resend timer expired event bit and queue the event processor whilst we're changing state to one where the resend timer is irrelevant as the event can just be ignored by the processor thereafter. ======================================================= [ INFO: possible circular locking dependency detected ] 2.6.35-rc3-cachefs+ #115 ------------------------------------------------------- swapper/0 is trying to acquire lock: (&call->state_lock){++--..}, at: [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc] but task is already holding lock: (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&call->resend_timer){+.-...}: [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa [<ffffffff81056184>] lock_acquire+0x57/0x6d [<ffffffff8103bb9c>] del_timer_sync+0x3c/0x86 [<ffffffffa002bb7a>] rxrpc_send_abort+0x50/0x97 [af_rxrpc] [<ffffffffa002bdd9>] rxrpc_kernel_abort_call+0xa1/0xdd [af_rxrpc] [<ffffffffa0061588>] afs_deliver_to_call+0x129/0x368 [kafs] [<ffffffffa006181b>] afs_process_async_call+0x54/0xff [kafs] [<ffffffff8104261d>] worker_thread+0x1ef/0x2e2 [<ffffffff81045f47>] kthread+0x7a/0x82 [<ffffffff81002cd4>] kernel_thread_helper+0x4/0x10 -> #0 (&call->state_lock){++--..}: [<ffffffff81055237>] validate_chain+0x727/0xd23 [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa [<ffffffff81056184>] lock_acquire+0x57/0x6d [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43 [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc] [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5 [<ffffffff81036828>] __do_softirq+0xa2/0x13e [<ffffffff81002dcc>] call_softirq+0x1c/0x28 [<ffffffff810049f0>] do_softirq+0x38/0x80 [<ffffffff810361a2>] irq_exit+0x45/0x47 [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96 [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20 [<ffffffff810011ac>] cpu_idle+0x4d/0x83 [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1 other info that might help us debug this: 1 lock held by swapper/0: #0: (&call->resend_timer){+.-...}, at: [<ffffffff8103b675>] run_timer_softirq+0x182/0x2a5 stack backtrace: Pid: 0, comm: swapper Not tainted 2.6.35-rc3-cachefs+ #115 Call Trace: <IRQ> [<ffffffff81054414>] print_circular_bug+0xae/0xbd [<ffffffff81055237>] validate_chain+0x727/0xd23 [<ffffffff810560bc>] __lock_acquire+0x889/0x8fa [<ffffffff810539a7>] ? mark_lock+0x42f/0x51f [<ffffffff81056184>] lock_acquire+0x57/0x6d [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc] [<ffffffff813e6b69>] _raw_read_lock_bh+0x34/0x43 [<ffffffffa00200d4>] ? rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc] [<ffffffffa00200d4>] rxrpc_resend_time_expired+0x56/0x96 [af_rxrpc] [<ffffffff8103b6e6>] run_timer_softirq+0x1f3/0x2a5 [<ffffffff8103b675>] ? run_timer_softirq+0x182/0x2a5 [<ffffffffa002007e>] ? rxrpc_resend_time_expired+0x0/0x96 [af_rxrpc] [<ffffffff810367ef>] ? __do_softirq+0x69/0x13e [<ffffffff81036828>] __do_softirq+0xa2/0x13e [<ffffffff81002dcc>] call_softirq+0x1c/0x28 [<ffffffff810049f0>] do_softirq+0x38/0x80 [<ffffffff810361a2>] irq_exit+0x45/0x47 [<ffffffff81018fb3>] smp_apic_timer_interrupt+0x88/0x96 [<ffffffff81002893>] apic_timer_interrupt+0x13/0x20 <EOI> [<ffffffff81049de1>] ? __atomic_notifier_call_chain+0x0/0x86 [<ffffffff8100955b>] ? mwait_idle+0x6e/0x78 [<ffffffff81009552>] ? mwait_idle+0x65/0x78 [<ffffffff810011ac>] cpu_idle+0x4d/0x83 [<ffffffff813e06f3>] start_secondary+0x1bd/0x1c1 Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
The packet length should be checked before the packet data is dereferenced. Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
The packet length should be checked before the packet data is dereferenced. Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
The packet length should be checked before the packet data is dereferenced. Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Acked-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Changli Gao authored
On the TX path, skb->data points to the ethernet header, not the network header. So when validating the packet length for accessing we should take the ethernet header into account. Signed-off-by:
Changli Gao <xiaosuo@gmail.com> Acked-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 04 Aug, 2010 7 commits
-
-
Joe Perches authored
Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Stefan Weil authored
free_netdev finally calls kfree which makes the contents of ndev and priv (private data contained in ndev) invalid. So iounmap should be called before free_netdev. Cc: David S. Miller <davem@davemloft.net> Cc: Chaithrika U S <chaithrika@ti.com> Cc: Sriramakrishnan <srk@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Stefan Weil <weil@mail.berlios.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kulikov Vasiliy authored
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by:
Kulikov Vasiliy <segooon@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kulikov Vasiliy authored
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by:
Kulikov Vasiliy <segooon@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kulikov Vasiliy authored
IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by:
Kulikov Vasiliy <segooon@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivialLinus Torvalds authored
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits) Documentation: update broken web addresses. fix comment typo "choosed" -> "chosen" hostap:hostap_hw.c Fix typo in comment Fix spelling contorller -> controller in comments Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault fs/Kconfig: Fix typo Userpace -> Userspace Removing dead MACH_U300_BS26 drivers/infiniband: Remove unnecessary casts of private_data fs/ocfs2: Remove unnecessary casts of private_data libfc: use ARRAY_SIZE scsi: bfa: use ARRAY_SIZE drm: i915: use ARRAY_SIZE drm: drm_edid: use ARRAY_SIZE synclink: use ARRAY_SIZE block: cciss: use ARRAY_SIZE comment typo fixes: charater => character fix comment typos concerning "challenge" arm: plat-spear: fix typo in kerneldoc reiserfs: typo comment fix update email address ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hidLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (30 commits) Revert "HID: add support for the Wacom Intuos 4 wireless" HID: fix up Kconfig entry for ACRUX driver HID: add ACRUX game controller force feedback support HID: Force input registration for "VEC footpedal" HID: add HID_QUIRK_HIDINPUT_FORCE HID: hid-input.c: indentation fixes HID: hiddev: use usb_find_interface, get rid of BKL HID: ignore digitizer usage Undefined (0x00) HID: Add support for Conceptronic CLLRCMCE HID: hid-ids.h: Whitespace fixup, align using TABs HID: picolcd: implement refcounting of framebuffer HID: picolcd: do not reallocate memory on depth change HID: picolcd: Add minimal palette required by fbcon on 8bpp HID: magicmouse: Correct parsing of large X and Y motions. HID: magicmouse: report last touch up HID: picolcd: fix deferred_io init/cleanup to fb ordering HID: hid-ids.h: keep vendor ids in alphabetical order HID: add proper support for Elecom BM084 bluetooth mouse HID: magicmouse: enable horizontal scrolling HID: magicmouse: add param for scroll speed ...
-