"make dtbs_check":

    arch/arm/boot/dts/r9a06g032-rzn1d400-db.dt.yaml: timer: compatible: 'oneOf' conditional failed, one must be fixed:
	    ['arm,cortex-a7-timer', 'arm,armv7-timer'] is too long
	    'arm,cortex-a7-timer' is not one of ['arm,cortex-a15-timer']
	    'arm,cortex-a7-timer' is not one of ['arm,armv7-timer']
	    'arm,cortex-a7-timer' is not one of ['arm,armv8-timer']
	    From schema: Documentation/devicetree/bindings/timer/arm,arch_timer.yaml

The Cortex-A7 timer should just declare compatibility with
"arm,armv7-timer".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a8e0cf00a983b4c539cdb1cfad5cc6b10b423c5b.1649680220.git.geert+renesas@glider.be

Add device nodes for the General Purpose Input/Output (GPIO) blocks on
the Renesas R-Car S4-8 (R8A779F0) SoC.

Note that GPIO blocks 4-7 are not added, as they can only be accessed
from the Control Domain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7fb68561026fa8bb5d9baf0596560c5c719a38cc.1649086225.git.geert+renesas@glider.be

Enable Ethernet{0,1} interfaces on RZ/G2UL SMARC EVK.

Ethernet0 pins are muxed with CAN0, CAN1, SSI1 and RSPI1 pins and Ethernet0
device selection is based on the SW1[3] switch position.

Set SW1[3] to position OFF for selecting CAN0, CAN1, SSI1 and RSPI1.
Set SW1[3] to position ON for selecting Ethernet0.

This patch disables Ethernet0 on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-8-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

RZ/G2UL SoM has both 64GB eMMC and microSD connected to SDHI0.

Both these interfaces are mutually exclusive and the SD0 device
selection is based on SW1[2] on SoM module.

Set SW1[2] to position OFF for selecting eMMC
Set SW1[2] to position ON for selecting microSD

This patch enables eMMC on RZ/G2UL SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-7-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable the microSD card slot connected to SDHI1 on the RZ/G2UL SMARC
platform by removing the sdhi1 override which disabled it, and by adding
the necessary pinmux required for SDHI1.

This patch also adds gpios property to vccq_sdhi1 regulator.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-6-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add Gigabit Ethernet{0,1} nodes to SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-5-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add SDHI{0, 1} nodes to RZ/G2UL SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-4-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add scif0 and audio clk pins to soc pinctrl dtsi and drop deleting
the pinctrl-0 and pinctrl-names properties for scif0 node so that
we now actually make use of these properties for scif0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-3-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Fillup the pinctrl(GPIO) stub node in RZ/G2UL SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220402081328.26292-2-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add basic support for RZ/G2UL SMARC EVK (based on R9A07G043U11):
- memory
- External input clock
- CPG
- DMA
- SCIF

It shares the same carrier board with RZ/G2L, but the pin mapping is
different. Disable the device nodes which are not tested and delete the
corresponding pinctrl definitions.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-4-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add initial DTSI for RZ/G2UL SoC.

Both RZ/G2L and RZ/G2UL uses the same SMARC EVK. Therefore they share
the common dtsi (rz-smarc.dtsi) file. Place holders are added in
device nodes to avoid compilation errors for the devices which have
not been enabled yet on RZ/G2UL SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220412161314.13800-3-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Renesas RZ/G2UL DT Binding Definitions

Clock and reset definitions for the Renesas RZ/G2UL (R9A07G043) SoC,
shared by driver and DT source files.

On RZ/G2{L,LC} SoM module, gpio for power selection is connected to
P39_1 whereas on RZ/G2UL it is connected to P6_1. So move gpios property
of vccq_sdhi1 regulator from common dtsi to soc specific dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401175427.19078-1-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

RSPI1 (SPI1) interface is available on PMOD0 connector (J1) on the
carrier board.  This patch adds pinmux and spi1 nodes to the carrier
board dtsi file and drops deleting pinctl* properties from DTS file.

RSPI1 interface is tested by setting the macro SW_RSPI_CAN to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220401145702.17954-1-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add the RPC HyperFlash device node along with its partitions to the
common ULCB board DTS file.

Based on a patch in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/61a63e819d4296760ca7ae83ef5226a2c4d7bd93.1648548339.git.geert+renesas@glider.be

Add the RPC HyperFlash device node along with its partitions to the
common Salvator-X(S) board DTS file.

Based on a patch in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cfc6af8a4c42febcc405b7356c38448eec8e29b0.1648548339.git.geert+renesas@glider.be

Add the RPC HyperFlash device node along with its partitions to the
common Ebisu board DTS file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b14c769f62211b67d90dbd2f127357756e6cb4fa.1648548339.git.geert+renesas@glider.be

Add the RPC HyperFlash device node along with its partitions to the
common Draak board DTS file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0f3d3018ecfcdce1bce67708708a6d3a98368b10.1648548339.git.geert+renesas@glider.be

Add device nodes for the SPI Multi I/O Bus Controllers (RPC-IF) on the
various R-Car Gen3 SoCs that do not have support for them yet in their
device trees (R-Car H3, M3-W, M3-W+, M3-N, E3, and D3).

Based on patches in the BSP by Valentine Barshak.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/3231749c7b63df1a2134daabe66446a3e0e5515b.1648548339.git.geert+renesas@glider.be

Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-6-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-5-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-4-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-3-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Driver doesn't use it yet, but let's describe the HW properly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220322095512.4707-2-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Define RZ/G2UL (R9A07G043U) Clock Pulse Generator Core Clock and module
clock outputs, as listed in Table 7.1.4.2 ("Clock List r0.51") and also
add Reset definitions referring to registers CPG_RST_* in Section 7.2.3
("Register configuration") of the RZ/G2UL Hardware User's Manual (Rev.
0.51, Nov. 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220402073037.23947-3-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add a DTS file for the Spider Ether TSN sub-board (RTP8A779F0ASKB0ST0S),
and include it from the main r8a779f0-spider.dts.

For now its contents are limited to the Board ID EEPROM.

Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5aa58816182b34d9e5795bc1e22784f4e4879d13.1643898884.git.geert+renesas@glider.be

Enable the I2C4 bus on the Falcon CPU board, and describe the I2C EEPROMs
present on the Spider CPU and BreakOut boards.

Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/6d8917e49f83b6a932970ca169100eb086d11f16.1643898884.git.geert+renesas@glider.be

Add device nodes for the I2C Bus Interfaces on the Renesas R-Car S4-8
(R8A779F0) SoC.

Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e1c7fb17801bc82a74aa5364212d02ba51535dd2.1643898884.git.geert+renesas@glider.be

Add the device node for the CAN-FD device on R-Car M3-W+.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220319223306.60782-2-wsa+renesas@sang-engineering.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enables confirmed-working CAN interfaces 0 and 1 on the Falcon board.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20220309162609.3726306-4-uli+renesas@fpond.euSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

This patch adds a CANFD device node for r8a779a0.

Based on patch by Kazuya Mizuguchi.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20220309162609.3726306-3-uli+renesas@fpond.euSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

The INTC block is a better choice for handling the interrupts on the V3U
as the INTC will always be powered, while the GPIO block may be
de-clocked if not in use. Further more, it may be likely to have a lower
power consumption as it does not need to drive the pins.

Switch the interrupt parent and interrupts definition from gpio1 to
irq0 on intc_ex, and configure the PFC accordingly.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20220309190631.1576372-1-kieran.bingham+renesas@ideasonboard.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add TSU and thermal-zones nodes to RZ/V2L (R9A07G054) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220308223324.7456-4-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add OPP table for RZ/V2L SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220308223324.7456-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Renesas RZ/V2L SoC has Mali-G31 GPU, this patch fills up the GPU node and
adds opp table to RZ/V2L (R9A07G054) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220308223324.7456-2-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add vdd core regulator (1.1 V) for GPU.

This patch add regulator support for GPU.

The H/W manual mentions nothing about a GPU regulator. So using vdd
core regulator for GPU.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220307192436.13237-4-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable OSTM{1, 2} interfaces on RZ/G2LC SMARC EVK.
OSTM0 is reserved for TF-A.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220307192436.13237-3-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable mt25qu512a flash connected to QSPI0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220307192436.13237-2-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable Audio on RZ/G2LC SMARC EVK by deleting ssi0 entries from
board DT and adding pincontrol entries to the soc-pinctrl dtsi,
so that entries from common dtsi kick in and make audio functionality
operational.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220303164155.7706-5-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Enable i2c{0,1} on RZ/G2LC SMARC EVK by deleting respective
entries from board dts and adding pincontrol entries to the
soc-pinctrl dtsi. Also enable i2c2 by adding to soc dtsi.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220303164155.7706-4-biju.das.jz@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>