If the driver gets stuck holding the kernel timeline, we cannot issue a
heartbeat and so fail to discover that the driver is indeed stuck and do
not issue a GPU reset (which would hopefully unstick the driver!).
Switch to using a trylock so that we can query if the heartbeat's
timeline mutex is locked elsewhere, and then use the timer to probe if it
remains stuck at the same spot for consecutive heartbeats, indicating
that the mutex has not been released and the engine has not progressed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200702095219.963-1-chris@chris-wilson.co.uk

intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before encoder_type is set. This caused GEN11+ to incorrectly strip
HBR3 from source rates for edp. Move intel_dp_set_source_rates() to
after encoder_type is set. Add comment to intel_dp_is_edp() describing
unsafe usages.

v2: Alter intel_dp_set_source_rates final position (Ville/Manasi).
    Remove outdated comment (Ville).
    Slight optimization of control flow in intel_dp_init_connector.
    Slight rewording in commit message.
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630233310.10191-1-matthew.s.atwood@intel.com

'level' here means the highest level we can't use, so when checking
the fbc watermarks we need a -1 to get at the last enabled level.

While at if refactor the code a bit to declutter
g4x_compute_pipe_wm().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-12-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

To simplify things, call the combo PHY/TBT PLL calculation functions
directly from the corresponding combo/TypeC PLL get functions, instead of
calling the same calculation functions after having to recheck if the
given PHY is combo or TypeC.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629185848.20550-2-imre.deak@intel.com

When the reference clock is 38.4MHz, using the current TBT PLL
fractional divider value results in a slightly off TBT link frequency.
This causes an endless loop of link training success followed by a bad
link signaling and retraining at least on a Dell WD19TB TBT dock.  The
workaround provided by the HW team is to divide the fractional divider
value by two. This fixed the link training problem on the ThinkPad dock.

The same workaround is needed on some EHL platforms and for combo PHY
PLLs, these will be addressed in a follow-up.

Bspec: 49204

References: HSDES#22010772725
References: HSDES#14011861142
Reported-and-tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200629185848.20550-1-imre.deak@intel.com

The obj->lut_list is traversed when the object is closed as the file
table is destroyed during process termination. As this occurs before we
kill any outstanding context if, due to some bug or another, the closure
is blocked, then we fail to shootdown any inflight operations
potentially leaving the GPU spinning forever. As we only need to guard
the list against concurrent closures and insertions, the hold is short
and merits being treated as a simple spinlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701084439.17025-1-chris@chris-wilson.co.uk

We don't need intel_dig_port and dig_port to refer to the same thing.
Prefer the latter.

v2: fix coding style
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626234834.26864-2-lucas.demarchi@intel.com

This registers will be used to implement PSR2 manual tracking/selective
fetch.

v2:
- Fixed typo in _PLANE_SEL_FETCH_BASE
- Renamed PSR2_MAN_TRK_CTL bits to better match spec names
- Renamed _PLANE_SEL_FETCH_* to better match spec names

BSpec: 55229
BSpec: 50424
BSpec: 50420
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626010151.221388-3-jose.souza@intel.com

Future patches will bring PSR2 selective fetch configuration
validation but most of the configuration checks will be used for HW
tracking and selective fetch so the reoder was necessary.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626010151.221388-2-jose.souza@intel.com

This property will be used by PSR2 software tracking, adding it to
GEN12+.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626010151.221388-1-jose.souza@intel.com

Rearrange the allocation of the mm_struct registration to avoid
allocating underneath the i915->mm_lock, so that we avoid tainting the
lock (and in turn many other locks that may be held as i915->mm_lock is
taken, and those locks we may want on the free [shrinker] paths). In
doing so, we convert the lookup to be RCU protected by courtesy of
converting the free-worker to be an rcu_work.

v2: Remember to use hash_rcu variants to protect the list iteration from
concurrent add/del.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200619194038.5088-1-chris@chris-wilson.co.uk

Often we seem to detect an underrun right after modeset on gen2.
It seems to be a spurious detection (potentially the pipe is still
in a wonky state when we enable the planes). An extra vblank wait
seems to cure it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-13-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

The default fbc1 compression interval we use is 500 frames. That
translates to over 8 seconds typically. That's rather excessive
so let's drop it to 1 second.

The hardware will not attempt recompression unless at least one
line has been modified, so a shorter compression interval should
not cause extra bandwidth use in the purely idle scenario. Of
course in the mostly idle case we are possibly going to recompress
a bit more.

Should really try to find some kind of sweet spot to minimize
the energy usage...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-11-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

Avoid the FBC_CONTROL rmw and just store the fbc compression
interval in the params/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-10-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

Parametrize the FBC_CONTROL bits for neater code.

Also add the one missing bit: "stop compression on modification".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-9-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

The hardware host tracking won't nuke the entire cfb (unless the
entire fb is written through the gtt) so don't clear the busy_bits
for gtt tracking.

Not that it really matters anymore since we've lost ORIGIN_GTT usage
everywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-7-ville.syrjala@linux.intel.comReviewed-by: José Roberto de Souza <jose.souza@intel.com>

The current fence_y_offset calculation is broken. I think it more or
less used to do the right thing, but then I changed the plane code
to put the final x/y source offsets back into the src rectangle so
now it's just subtraacting the same value from itself. The code would
never have worked if we allowed the framebuffer to have a non-zero
offset.

Let's do this in a better way by just calculating the fence_y_offset
from the final plane surface offset. Note that we don't align the
plane surface address to fence rows so with horizontal panning there's
often a horizontal offset from the fence start to the surface address
as well. We have no way to tell the hardware about that so we just
ignore it. Based on some quick tests the invlidation still happens
correctly. I presume due to the invalidation nuking at least the full
line (or a segment of multiple lines).

Fixes: 54d4d719 ("drm/i915: Overcome display engine stride limits via GTT remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429101034.8208-4-ville.syrjala@linux.intel.comReviewed-by: Matt Roper <matthew.d.roper@intel.com>

As we close a handle GEM object, we update the drm_file's idr with an
error^W NULL pointer to indicate the in-progress closure, and finally
removing it. If we read the idr directly, we may then see an invalid
object pointer, and in our debugfs per_file_stats() we therefore need
to protect against the entry being invalid.

[ 1016.651637] RIP: 0010:per_file_stats+0xe/0x16e
[ 1016.651646] Code: d2 41 0f b6 8e 69 8c 00 00 48 89 df 48 c7 c6 7b 74 8c be 31 c0 e8 0c 89 cf ff eb d2 0f 1f 44 00 00 55 48 89 e5 41
57 41 56 53 <8b> 06 85 c0 0f 84 4d 01 00 00 49 89 d6 48 89 f3 3d ff ff ff 7f 73
[ 1016.651651] RSP: 0018:ffffad3a01337ba0 EFLAGS: 00010293
[ 1016.651656] RAX: 0000000000000018 RBX: ffff96fe040d65e0 RCX: 0000000000000002
[ 1016.651660] RDX: ffffad3a01337c50 RSI: 0000000000000000 RDI: 00000000000001e8
[ 1016.651663] RBP: ffffad3a01337bb8 R08: 0000000000000000 R09: 00000000000001c0
[ 1016.651667] R10: 0000000000000000 R11: ffffffffbdbe5fce R12: 0000000000000000
[ 1016.651671] R13: ffffffffbdbe5fce R14: ffffad3a01337c50 R15: 0000000000000001
[ 1016.651676] FS:  00007a597e2d7480(0000) GS:ffff96ff3bb00000(0000) knlGS:0000000000000000
[ 1016.651680] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1016.651683] CR2: 0000000000000000 CR3: 0000000171fc2001 CR4: 00000000003606e0
[ 1016.651687] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1016.651690] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1016.651693] Call Trace:
[ 1016.651693] Call Trace:
[ 1016.651703]  idr_for_each+0x8a/0xe8
[ 1016.651711]  i915_gem_object_info+0x2a3/0x3eb
[ 1016.651720]  seq_read+0x162/0x3ca
[ 1016.651727]  full_proxy_read+0x5b/0x8d
[ 1016.651733]  __vfs_read+0x45/0x1bb
[ 1016.651741]  vfs_read+0xc9/0x15e
[ 1016.651746]  ksys_read+0x7e/0xde
[ 1016.651752]  do_syscall_64+0x54/0x68
[ 1016.651758]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: a8c15954 ("drm/i915: Protect debugfs per_file_stats with RCU lock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630152724.3734-1-chris@chris-wilson.co.uk

Currently there is no null check for a failed memory allocation
on the dsb object and without this a null pointer dereference
error can occur. Fix this by adding a null check.

Note: added a drm_err message in keeping with the error message style
in the function.

Addresses-Coverity: ("Dereference null return")
Fixes: afeda4f3 ("drm/i915/dsb: Pre allocate and late cleanup of cmd buffer")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616114221.73971-1-colin.king@canonical.com

There are a couple of spelling mistakes in kernel parameter help text,
namely "helpfull" and "paramters".  Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616082129.65517-1-colin.king@canonical.com

A single Ri mismatch doesn't automatically mean that the link integrity
is broken. Update and check of Ri and Ri' are done asynchronously. In
case an update happens just between the read of Ri' and the check against
Ri there will be a mismatch even if the link integrity is fine otherwise.
Signed-off-by: Oliver Barta <oliver.barta@aptiv.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504123524.7731-1-oliver.barta@aptiv.com

The linetime watermark is a 9 bit value, which gives us
a maximum linetime of just below 64 usec. If the linetime
exceeds that value we currently just discard the high bits
and program the rest into the register, which angers the
state checker.

To avoid that let's just clamp the value to the max. I believe
it should be perfectly fine to program a smaller linetime wm
than strictly required, just means the hardware may fetch data
sooner than strictly needed. We are further reassured by the
fact that with DRRS the spec tells us to program the smaller
of the two linetimes corresponding to the two refresh rates.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200625200003.12436-1-ville.syrjala@linux.intel.comReviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>

Update code to reflect recent bspec changes

Bspec: 52890
Bspec: 53508
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200624215723.2316-1-matthew.s.atwood@intel.com

This workaround now also applies to TGL and RKL, so extend the PCH test
to just capture everthing ICP and beyond.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200617180006.4130501-1-matthew.d.roper@intel.comReviewed-by: Matt Atwood <matthew.s.atwood@intel.com>

The DP spec says:
"The transmitter shall support at least three levels of voltage
 swing (Levels 0, 1, and 2).

 If only three levels of voltage swing are supported (VOLTAGE
 SWING SET field (bits 1:0) are programmed to 10 (Level 2)),
 this bit shall be set to 1, and cleared in all other cases.

 If all four levels of voltage swing are supported (VOLTAGE
 SWING SET field (bits 1:0) are programmed to 11 (Level 3)),
 this bit shall be set to 1,and cleared in all other cases."

Let's follow that exactly instead of the current apporach
where we can set those also for vswing/preemph levels 0 or 1
(or 2 when the platform max is 3).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200512174145.3186-7-ville.syrjala@linux.intel.comReviewed-by: Imre Deak <imre.deak@intel.com>

Catch up with upstream, in particular to get c1e8d7c6 ("mmap locking
API: convert mmap_sem comments").
Signed-off-by: Jani Nikula <jani.nikula@intel.com>

The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com

drm-misc-next for v5.9:

UAPI Changes:
- Add DRM_MODE_TYPE_USERDEF for video modes specified in cmdline.

Cross-subsystem Changes:
- Assorted devicetree binding updates.
- Add might_sleep() to dma_fence_wait().
- Fix fbdev's get_user_pages_fast() handling, and use pin_user_pages.
- Small cleanup with IS_BUILTIN in video/fbdev drivers.
- Fix video/hdmi coding style for infoframe size.

Core Changes:
- Silence vblank output during init.
- Fix DP-MST corruption during send msg timeout.
- Clear leak in drm_gem_objecs_lookup().
- Make newlines work with force connector attribute.
- Fix module refcounting error in drm_encoder_slave, and use new i2c api.
- Header fix for drm_managed.c
- More struct_mutex removal for !legacy drivers:
  - Remove gem_free_object()
  - Removal of drm_gem_object_put_unlocked().
- Show current->comm alongside pid in debug printfs.
- Add drm_client_modeset_check() + drm_client_framebuffer_flush().
- Replace drm_fb_swab16 with drm_fb_swap that also supports 32-bits.
- Remove mode->vrefresh, and compactify drm_display_mode.
- Use drm_* macros for logging and warnings.
- Add WARN when drm_gem_get_pages is used on a private obj.
- Handle importing and imported dmabuf better in shmem helpers.
- Small fix for drm/mm hole size comparison, and remove invalid entry optimization.
- Add a drm/mm selftest.
- Set DSI connector type for DSI panels.
- Assorted small fixes and documentation updates.
- Fix DDI I2C device registration for MST ports, and flushing on destroy.
- Fix master_set return type, used by vmwgfx.
- Make the drm_set/drop_master ioctl symmetrical.

Driver Changes:
 Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4, i915, omap, fbdev/sm712fb, fbdev/pxafb, console/newport_con, msm, virtio, udl, malidp, hdlcd, bridge/ti-sn65dsi86, panfrost.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE  Allow iommu in the sun4i driver and use it for sun8i.
- Simplify backlight lookup for omap, amba-clcd and tilcdc.
- Hold reg_lock for rockchip.
- Add support for bridge gpio and lane reordering + polarity to ti-sn65dsi86, and fix clock choice.
- Small assorted fixes to tilcdc, vc4 (multiple), i915.
- Remove hw cursor support for mgag200, and use simple kms helper + shmem helpers.
- Add support for KOE TX26D202VM0BWA panel.
- Use GEM CMA functions in arc, arm, atmel-hlcdc, fsi-dcu, hisilicon, imx, ingenic, komeda, malidp, mcde, meson, msxfb, rcar-du, shmobile, stm, sti, tilcdc, tve200, zte.
- Remove gem_print_info.
- Improve gem_create_object_helper so udl can use shmem helpers.
- Convert vc4 dt bindings to schemas, and add clock properties.
- Device initialization cleanups for mgag200.
- Add a workaround to fix DP-MST short pulses handling on broken hardware in i915.
- Allow build test compiling arm drivers.
- Use managed pci functions in mgag200 and ast.
- Use dev_groups in malidp.
- Add per pixel alpha support for PX30 VOP in rockchip.
- Silence deferred probe logs in panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/001cd9a6-405d-4e29-43d8-354f53ae4e8b@linux.intel.com

During encoder enabling we clear the flag before starting the ACT
sequence and wait for the flag, but the clearing is missing during
encoder disabling, add it there too. Since nothing cleared the flag
automatically we could've run subsequent disabling steps too early.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-5-imre.deak@intel.com

It's not clear if the DP_TP_STATUS flags other than the ACT sent flag
have some side-effect, so don't clear those; we don't depend on the
state of these flags anyway.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-4-imre.deak@intel.com

During transcoder enabling we'll configure the transcoder in MST mode
and enable the VC payload allocation, which will start the ACT sequence.
Before waiting for the ACT sequence completion, we need to clear the ACT
sent flag, but based on the above we can do this right before enabling
the transcoder.

For clarity, move the flag clearing closer to where we wait for it.

While at it also factor out some common code.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616141855.746-3-imre.deak@intel.com

During the initial probing of an MST sink, MST core will determine the
sink's link bandwidth based on its own version of the sink link
rate/lane count caps it reads from the DPCD. At a later point (after
probing and 1 or more modesets) i915 may limit the link parameters wrt.
the original source/sink common caps above due to link training failures
during a modeset and the resulting link training fallback logic.

Based on the above a modeset following another modeset with a link
training error will compute the i915 HW specific and DP protocol timing
parameters (data/link M/N and MST TU values) taking into account only
the unlimited source/sink common caps, but not taking into account the
fallback limits. This will also let DRM core oversubscribe the actual
link bandwidth during the MST payload allocation.

Prevent the above problem by disabling the link training fallback on MST
links for now, until the MST probe time initialization and the MST
compute config logic can deal with changing link parameters.

The misconfigured timings lead at least to a
'Timed out waiting for DP idle patterns'
error.

v2: (Ville)
- Print link training error message on the MST path too.
- Clarify the problem in the commit log.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-2-imre.deak@intel.com

MST encoders must use the master MST transcoder's DP_TP_STATUS and
DP_TP_CONTROL registers. Atm, during the HW readout of an MST encoder
connected to a slave transcoder we reset these register addresses in
intel_dp::regs.dp_tp_* to the slave transcoder's DP_TP_* register
addresses incorrectly; fix this.

One example where the above overwite happens is the encoder HW state
validation after enabling multiple streams; see
intel_dp_mst_enc_get_config(). After that during disabling any stream
we'll get a

'Timed out waiting for ACT sent when disabling'

error, due to reading from the incorrect DP_TP_STATUS register.

This change replaces
https://patchwork.freedesktop.org/patch/369577/?series=78193&rev=1
which just papered over the problem.

v2:
- Correct the failure scenario in the commit log. (José)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200616211146.23027-1-imre.deak@intel.com

Start using device specific parameters instead of module parameters for
most things. The module parameters become the immutable initial values
for i915 parameters. The device specific parameters in i915->params
start life as a copy of i915_modparams. Any later changes are only
reflected in the debugfs.

The stragglers are:

* i915.force_probe and i915.modeset. Needed before dev_priv is
  available. This is fine because the parameters are read-only and never
  modified.

* i915.verbose_state_checks. Passing dev_priv to I915_STATE_WARN and
  I915_STATE_WARN_ON would result in massive and ugly churn. This is
  handled by not exposing the parameter via debugfs, and leaving the
  parameter writable in sysfs. This may be fixed up in follow-up work.

* i915.inject_probe_failure. Only makes sense in terms of the module,
  not the device. This is handled by not exposing the parameter via
  debugfs.

v2: Fix uc i915 lookup code (Michał Winiarski)

Cc: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Cc: Venkata Sandeep Dhanalakota <venkata.s.dhanalakota@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200618150402.14022-1-jani.nikula@intel.com

Pull SELinux fixes from Paul Moore:
 "Three small patches to fix problems in the SELinux code, all found via
  clang.

  Two patches fix potential double-free conditions and one fixes an
  undefined return value"

* tag 'selinux-pr-20200621' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: fix undefined return of cond_evaluate_expr
  selinux: fix a double free in cond_read_node()/cond_read_list()
  selinux: fix double free

Pull pin control fixes from Linus Walleij:
 "Some early fixes collected during the first week after the merge
  window, all pretty self-evident, with the details below. The revert is
  the crucial thing.

   - Fix a warning on the Qualcomm SPMI GPIO chip being instatiated
     twice without a unique irqchip struct

   - Use the noirq variants of the suspend and resume callbacks in the
     Tegra driver

   - Clean up the errorpath on the MCP23s08 driver

   - Revert the use of devm_of_iomap() in the Freescale driver as it was
     regressing the platform

   - Add some missing pins in the Qualcomm IPQ6018 driver

   - Fix a simple documentation bug in the pinctrl-single driver"

* tag 'pinctrl-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: single: fix function name in documentation
  pinctrl: qcom: ipq6018 Add missing pins in qpic pin group
  Revert "pinctrl: freescale: imx: Use 'devm_of_iomap()' to avoid a resource leak in case of error in 'imx_pinctrl_probe()'"
  pinctrl: mcp23s08: Split to three parts: fix ptr_ret.cocci warnings
  pinctrl: tegra: Use noirq suspend/resume callbacks
  pinctrl: qcom: spmi-gpio: fix warning about irq chip reusage

Merge tag 'kbuild-fixes-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - fix -gz=zlib compiler option test for CONFIG_DEBUG_INFO_COMPRESSED

 - improve cc-option in scripts/Kbuild.include to clean up temp files

 - improve cc-option in scripts/Kconfig.include for more reliable
   compile option test

 - do not copy modules.builtin by 'make install' because it would break
   existing systems

 - use 'userprogs' syntax for watch_queue sample

* tag 'kbuild-fixes-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  samples: watch_queue: build sample program for target architecture
  Revert "Makefile: install modules.builtin even if CONFIG_MODULES=n"
  scripts: Fix typo in headers_install.sh
  kconfig: unify cc-option and as-option
  kbuild: improve cc-option to clean up all temporary files
  Makefile: Improve compressed debug info support detection

Pull powerpc fixes from Michael Ellerman:

 - One fix for the interrupt rework we did last release which broke
   KVM-PR

 - Three commits fixing some fallout from the READ_ONCE() changes
   interacting badly with our 8xx 16K pages support, which uses a pte_t
   that is a structure of 4 actual PTEs

 - A cleanup of the 8xx pte_update() to use the newly added pmd_off()

 - A fix for a crash when handling an oops if CONFIG_DEBUG_VIRTUAL is
   enabled

 - A minor fix for the SPU syscall generation

Thanks to Aneesh Kumar K.V, Christian Zigotzky, Christophe Leroy, Mike
Rapoport, Nicholas Piggin.

* tag 'powerpc-5.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/8xx: Provide ptep_get() with 16k pages
  mm: Allow arches to provide ptep_get()
  mm/gup: Use huge_ptep_get() in gup_hugepte()
  powerpc/syscalls: Use the number when building SPU syscall table
  powerpc/8xx: use pmd_off() to access a PMD entry in pte_update()
  powerpc/64s: Fix KVM interrupt using wrong save area
  powerpc: Fix kernel crash in show_instructions() w/DEBUG_VIRTUAL

Pull crypto fixes from Herbert Xu:

 - NULL dereference in octeontx

 - PM reference imbalance in ks-sa

 - deadlock in crypto manager

 - memory leak in drbg

 - missing socket limit check on receive SG list size in algif_skcipher

 - typos in caam

 - warnings in ccp and hisilicon

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: drbg - always try to free Jitter RNG instance
  crypto: marvell/octeontx - Fix a potential NULL dereference
  crypto: algboss - don't wait during notifier callback
  crypto: caam - fix typos
  crypto: ccp - Fix sparse warnings in sev-dev
  crypto: hisilicon - Cap block size at 2^31
  crypto: algif_skcipher - Cap recv SG list at ctx->used
  hwrng: ks-sa - Fix runtime PM imbalance on error