In rt2800_init_rfcsr_5592(), there's no need to write RF register 3 twice.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When routine rtl_is_special_data() is called with false as its last argument,
and the returned value is not tested, the call is essentially an extended
no-op. Accordingly, these calls may be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The wcn36xx_err macro should not end in a semicolon as
there are 2 consecutive semicolons in the preprocessed
output.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Eugene Krasnikov <k.eugene.e@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable the beacon changed using BSS_CHANGED_BEACON. This is
especially useful for mesh mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under heavy load, the relatively small number of RX queue entries are
completely filled. With an increase from 16 to 32 entries, this condition
rarely happens.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Arend van Spriel <arend@broadcom.com>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The cw1200_irq_handler() function expects the hwbus lock to be held when
it is called.  On the SDIO platform, this lock is implemented in terms
of sdio_claim_host/sdio_release_host.

This trivial patch makes it explicit that we are performing the hwbus
lock rather than something SDIO-specific.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The reason that a scan failed for some reason (typically bad
parameters) should be logged even when debugging is turned off.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We can mess logs if user space try to open device again and again if
RFKILL switch is on. Do not print message and return ERFKILL error
instead to indicate where the problem is.

Note that iwl4965 handle this problem differently, it allows to open
device when radio is disabled.
Reported-by: Dietmar Rudolph <dietmar@crlf.de>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

the original code used goto out if kzalloc fails,but the out include kfree,
so return -ENOMEM if kzalloc fails.
Signed-off-by: Jing Wang <windsdaemon@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since firmware loading became async it is possible that if_sdio_finish_power_of
is called with only one remaining runtime_pm reference, so it isn't safe
to call pm_runtime_put_noidle.  We must call pm_runtime_put().
Diagnosed-by: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mirror the latest MediaTek/Ralink driver with respect to RT5390 RF register
programming.  The PCI and USB devices use different init values.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1) Move common code out of switch case handling
2) Return from the function if number of bytes left in response buffer
are less than tlv size
3) Pass pg_tlv_hdr directly instead of txp_cfg to mwifiex_get_power_level()
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Update bbp register initialization for RT53xx chips to match with the
latest MediaTek/Ralink driver.

Based on: NICInitRT5390BbpRegisters()
From: DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5390.c

Signed-off-by: Kevin Lo <kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adding the debugfs file <debugfs_mnt>/brcmfmac/<devid>/chipinfo
which contains the chip number and revision.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The dhd.h file contained a number of definitions that are
related to events received from the firmware. Those are
processed and dispatched in the driver by fweh. Hence the
definitions are moved to its include file.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Removing WLC_PHY_TYPE and some BRCMF_E_.* definitions as these
are not used in the driver sources.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The BCDC protocol layer is using a mix of naming of CDC, BDC and
BCDC. Use the name BCDC consistenly over all functions, defines
and variables. This patch does not change code functionality.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Move the command codes to the firmware interface module as
that makes a bit more sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware control interface is provided by fwil source file, but
a number of structures used to communicate with the firmware still
resided in dhd.h. The patch moves them to fwil_types.h.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In bcmsdh.c the functions brcmf_sdio_probe() and brcmf_sdio_remove()
were exported, but that is not needed. The functions are linked into
the driver module, which is the only one needing to call these.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Knowing the firmware version is pretty useful information when
looking at issues. It is retrieved during initialization so
store it in driver data structure to fill the ethtool driver
info when requested.
Reviewed-by: Hante Meuleman <meuleman@brodcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

BCDC is the default protocol layer and being called directly. This
patch installs the functions for this layer dynamically. This allows
new protocols to be added and selected dynamically depending on the
hw capabilties. As currently only BCDC is supported this is always
the installed protocol.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The ioctl() entry points were empty except for handling SIOC_ETHTOOL
but that has been obsoleted in favor of struct ethtool_ops. Cleaning
up removing the ioctl() handlers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The SDIO part of the brcmfmac driver uses a static define BRCMF_SDALIGN
to align buffers used for SDIO transfers. This patch replaces it by
using alignment derived from the platform specific data.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The alignment values were being determined for each transmit
and receive depending on platform data. Instead determine
these once during the probe.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

dhd_proto.h was cleaned up and prototypes were moved to dhd.h.
dhd_proto.h was removed. This is a step in cleaning and
restucturing protocol layer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

dhd_cdc is renamed to bcdc. This is a step in cleaning and
restructuring protocol layer. This is done so new protocols can
be added in the future. This step only renames the source files.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
[arend@broadcom.com: use 'git mv' to do the rename]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

New WiFi full dongle supports receiving chained packets in one command
through the SDIO bus. This patch adds the support on the host side to
send chained packets.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add firmware/nvram file name for bcm4339 so fmac can actually be functional with
the chip.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When CONFIG_BRCMDBG is not set we get the following build issue:
  CC [M]  drivers/net/wireless/brcm80211/brcmfmac/fwsignal.o
drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:
    In function ‘brcmf_fws_hdrpush’:
	drivers/net/wireless/brcm80211/brcmfmac/fwsignal.c:852:18:
	error: ‘BRCMF_FWS_TYPE_SEQ_LEN’ undeclared

The define BRCMF_FWS_TYPE_SEQ_LEN was introduced by:

    commit 6918f38e4ed4e0493a90a4331e0033bdfc806e00
    Author: Hante Meuleman <meuleman@broadcom.com>
    Date:   Wed Oct 23 14:58:51 2013 +0200

        brcmfmac: Update fwsignal to fix out of order tx.

Unfortunately, it was put in conditional part of the source
file under #ifdef DEBUG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "eb9c174 brcmfmac: determine host controller related
variables during probe" was not implemented correctly as the
information is already needed in brcmf_sdbrcm_probe(). This patch
moves it to brcmf_sdioh_attach() instead.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The SDPCM header can be traced, but it used a fixed header size. With
txglom feature the SDPCM header will have additional 8 bytes of hardware
extension header so SDIO core can properly handle the txglom packet.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The brcmsmac relies BCMA functionality to access the device. This
patch selects CONFIG_BCMA when CONFIG_BCMA_POSSIBLE is set. This
way the user does not need to be select BCMA to make the brcmsmac
driver show up in his menuconfig.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The SleepCSR register is accessed to wakeup the device from the
host side. Depending on the state of the device this may take
multiple attempts. The failed attempt are not real failures so
reduce the log level specifically for this register. The calling
function will scream when the multiple attempts all failed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

remove empty brcmf_proto_stop from protocol layer
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Moving the call to netif_start_queue() after brcmf_cfg80211_up() is
completed successful. If not return -EIO instead of -1 as that results
in 'Operation not permitted' which can put user on wrong track.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The bus-specific interface allowed a list of dongle commands to be
provided to the common driver part. However, upcoming functionality
requires a more dynamic behaviour. Hence the list is replaced
by a new callback function so the bus-specific driver part can
implement this behaviour.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>