- 11 Aug, 2015 4 commits
-
-
Frederic Danis authored
Parse platform_device's ACPI to retrieve UART init speed. When BCM device is open, check if its TTY has same parent as one of the platform devices saved. If yes, use platform_device's init speed. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Frederic Danis authored
Power management support for BCM2E39 is now performed in Bluetooth BCM UART driver. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Frederic Danis authored
Retrieve "shutdown" and "device_wakeup" GPIOs from ACPI. Set device off during platform device enumeration. Set device on only when attached. As driver can be unbound we need to check if the bcm_device still exists before calling GPIO's functions, this is protected using device_list_lock. Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Yong Li authored
When the device tree support is disabled, the fifo_pin is uninitialized, this patch will set the fifo_pin value based on platform data Signed-off-by: Yong Li <sdliyong@gmail.com> Acked-by: Varka Bhadram <varkabhadram@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 10 Aug, 2015 36 commits
-
-
Ben Young Tae Kim authored
QCA61x4 chips have supported sleep feature using In-Band-Sleep commands to enable sleep feature based on H4 protocol. After sending patch/nvm configuration is done, IBS mode will be up and running Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Ben Young Tae Kim authored
This is for supporting BT for QCA ROME with vendor specific HCI commands and initialization on the chip. This will have USB/UART implementation both, but for now, adding UART vendor specific commands to patch downloading and set Bluetooth device address using vendor specific command. Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
Currently, when trying to connect to already paired device that just rotated its RPA MAC address, old address would be used and connection would fail. In order to fix that, kernel must scan and receive advertisement with fresh RPA before connecting. This patch enables new connection establishment procedure. Instead of just sending HCI_OP_LE_CREATE_CONN to controller, "connect" will add device to kernel whitelist and start scan. If advertisement is received, it'll be compared against whitelist and then trigger connection if it matches. That fixes mentioned reconnect issue for already paired devices. It also make whole connection procedure more robust. We can try to connect to multiple devices at same time now, even though controller allow only one. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
Currently, when trying to connect to already paired device that just rotated its RPA MAC address, old address would be used and connection would fail. In order to fix that, kernel must scan and receive advertisement with fresh RPA before connecting. This patch makes sure that when new procedure is in use, and we're stuck in scan phase because no advertisement was received and timeout happened, or app decided to close socket, scan whitelist gets properly cleaned up. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
Currently, when trying to connect to already paired device that just rotated its RPA MAC address, old address would be used and connection would fail. In order to fix that, kernel must scan and receive advertisement with fresh RPA before connecting. This path makes sure that after advertisement is received from device that we try to connect to, it is properly handled in check_pending_le_conn and trigger connect attempt. It also modifies hci_le_connect to make sure that connect attempt will be properly continued. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
Currently, when trying to connect to already paired device that just rotated its RPA MAC address, old address would be used and connection would fail. In order to fix that, kernel must scan and receive advertisement with fresh RPA before connecting. This patch adds hci_connect_le_scan with dependencies, new method that will be used to connect to remote LE devices. Instead of just sending connect request, it adds a device to whitelist. Later patches will make use of this whitelist to send conenct request when advertisement is received, and properly handle timeouts. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
This patch adds hci_lookup_le_connect method, that will be used to check wether outgoing le connection attempt is in progress. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Jakub Pawlowski authored
Currently, when trying to connect to already paired device that just rotated its RPA MAC address, old address would be used and connection would fail. In order to fix that, kernel must scan and receive advertisement with fresh RPA before connecting. This patch adds some fields to hci_conn_params, in preparation to new connect procedure. explicit_connect will be used to override any current auto_connect action, and connect to device when ad is received. HCI_AUTO_CONN_EXPLICIT was added to auto_connect enum. When this value will be used, explicit connect is the only action, and params can be removed after successful connection. HCI_CONN_SCANNING is added to hci_conn flags. When it's set, connect is scan phase. It gets cleared when advertisement is received, and HCI_OP_LE_CREATE_CONN is sent. Signed-off-by: Jakub Pawlowski <jpawlowski@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch fixes the error handling for lowpan_xmit_fragment by replace "-PTR_ERR" to "PTR_ERR". PTR_ERR returns already a negative errno code. Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch introduce a new mib entry which isn't part of 802.15.4 but useful as default behaviour to set the ack request bit or not if we don't know if the ack request bit should set. This is currently used for stacks like IEEE 802.15.4 6LoWPAN. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch changes the state change behaviour of at86rf230 to always TX_ARET mode. According the at86rf2xx datasheets TX_ARET mode doesn't mean to be always waiting for ack frames after transmit. The transceiver will automatically wait for ack frames or not if the acknowledge request bit is set. See section "TX_ARET_ON – Transmit with Automatic Frame Retransmission and CSMA-CA Retry". Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch changes the default minimum value of frame_retries to 0 and changes the frame_retries default value to 3 which is also 802.15.4 default. We don't use the frame_retries "-1" value as indicator for no-aret mode anymore, instead we checking on the ack request bit inside the 802.15.4 frame control field. This allows a acknowledge handling per frame. This checking is done by transceiver or inside xmit callback of driver layer. If a transceiver doesn't support ARET handling the transmit functionality ignores ack frames then, which isn't well but should not effect anything of current functionality. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
This patch removes several checks if a value is really changed. This makes only sense if we have another layer call e.g. calling the driver_ops which is done by callbacks like "set_channel". For MAC settings which need to be set by phy registers (if the phy supports that handling) this is set by doing an interface up currently and are not direct driver_ops calls, so we remove the checks from these configuration callbacks. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Suggested-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
If we currently change the mac address inside the wpan interface while we have a lowpan interface on top of the wpan interface, the mac address setting doesn't reach the lowpan interface. The effect would be that the IPv6 lowpan interface has the old SLAAC address and isn't working anymore because the lowpan interface use in internal mechanism sometimes dev->addr which is the old mac address of the wpan interface. This patch checks if a wpan interface belongs to lowpan interface, if yes then we need to check if the lowpan interface is down and change the mac address also at the lowpan interface. When the lowpan interface will be set up afterwards, it will use the correct SLAAC address which based on the updated mac address setting. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Tested-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Alexander Aring authored
We currently supports multiple lowpan interfaces per wpan interface. I never saw any use case into such functionality. We drop this feature now because it's much easier do deal with address changes inside the under laying wpan interface. This patch removes the multiple lowpan interface and adds a lowpan_dev netdev pointer into the wpan_dev, if this pointer isn't null the wpan interface belongs to the assigned lowpan interface. Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Tested-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Lukasz Duda authored
The lowpan_fetch_skb function is used to fetch the first byte, which also increments the data pointer in skb structure, making subsequent array lookup of byte 0 actually being byte 1. To decompress the first byte of the Flow Label when the TF flag is set to 0x01, the second half of the first byte is needed. The patch fixes the extraction of the Flow Label field. Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Lukasz Duda <lukasz.duda@nordicsemi.no> Signed-off-by: Glenn Ruben Bakke <glenn.ruben.bakke@nordicsemi.no> Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Aniket Nagarnaik authored
We will not release sdio bus until firmware is completely downloaded and becomes ready. Our 8887 A2 chip can have separate firmware images for WLAN and bluetooth. This patch fixes an issue observed when both drivers simultaneously try to download respective firmwares. Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Dan Carpenter authored
We should be passing the pointer itself instead of the address of the pointer. This was a copy and paste bug when we replaced the calls to hci_send_cmd(). Originally, the arguments were "len, cp" but we overwrote them with "sizeof(cp), &cp" by mistake. Fixes: b3d39140 ('Bluetooth: Move amp assoc read/write completed callback to amp.c') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Couple of fixes/adjustments Ido Schimmel (5): mlxsw: Call free_netdev when removing port mlxsw: Make system port to local port mapping explicit mlxsw: Simplify mlxsw_sx_port_xmit function mlxsw: Use correct skb length when dumping payload mlxsw: Fix use-after-free bug in mlxsw_sx_port_xmit Jiri Pirko (2): mlxsw: Make pci module dependent on HAS_DMA and HAS_IOMEM mlxsw: Strip FCS from incoming packets ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Store the length of the skb before transmitting it and use it for stats instead of skb->len, since skb might have been freed already. This issue was discovered using the Kernel Address sanitizer (KASan). Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Do not use the length of the transmitted skb (which was freed), but that of the response skb. This issue was discovered using the Kernel Address sanitizer (KASan). Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Previously we only checked if the transmission queue is not full in the middle of the xmit function. This lead to complex logic due to the fact that sometimes we need to reallocate the headroom for our Tx header. Allow the switch driver to know if the transmission queue is not full before sending the packet and remove this complex logic. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
FCS of incoming packets is already checked by HW. Just strip it out. Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
This resolves compile errors on um-allyesconfig. Note that there are many other drivers which have the same issue. Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
System ports are unique identifiers in a multi-ASIC environment that represent all the available ports in the system. Local ports on the other hand, are unique only within the local ASIC. Since system port to local port mapping is not part of the HW-SW contract and since only single-ASIC configurations are currently supported, set an explicit 1:1 mapping by configuring the Switch System Port Record (SSPR) register. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
When removing a port's netdevice we should also free the memory allocated by alloc_etherdev(). Do this by calling free_netdev() at the end of the teardown sequence. Reported-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Masanari Iida authored
This patch fix double word "the the" in Documentation/DocBook/networking/API-eth-get-headlen.html Documentation/DocBook/networking/netdev.html Documentation/DocBook/networking.xml These files are generated from comment in source, so I have to fix comment in net/ethernet/eth.c. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shaohui Xie authored
RTL8211DN is compatible with RTL8211E. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Robert Shearman authored
RFC 4182 s2 states that if an IPv4 Explicit NULL label is the only label on the stack, then after popping the resulting packet must be treated as a IPv4 packet and forwarded based on the IPv4 header. The same is true for IPv6 Explicit NULL with an IPv6 packet following. Therefore, when installing the IPv4/IPv6 Explicit NULL label routes, add an attribute that specifies the expected payload type for use at forwarding time for determining the type of the encapsulated packet instead of inspecting the first nibble of the packet. Signed-off-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Kaixu Xia says: ==================== bpf: Introduce the new ability of eBPF programs to access hardware PMU counter This patchset is base on the net-next: git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git commit 9dc20a64. Previous patch v6 url: https://lkml.org/lkml/2015/8/4/188 changes in V7: - rebase the whole patch set to net-next tree(9dc20a64); - split out the core perf APIs into Patch 1/5; - change the return value of function perf_event_attrs() from struct perf_event * to const struct perf_event * in Patch 1/5; - rename the function perf_event_read_internal() to perf_event_ read_local() and rewrite it in Patch 1/5; - rename the function check_func_limit() to check_map_func _compatibility() and remove the unnecessary pass pointer to a pointer in Patch 4/5; changes in V6: - make the Patch 1/4 commit message more meaning and readable; - remove the unnecessary comment in Patch 2/4 and make it clean; - declare the function perf_event_release_kernel() in include/ linux/perf_event.h to fix the build error when CONFIG_PERF_EVENTS isn't configured in Patch 2/4; - add function perf_event_attrs() to get the struct perf_event_attr in Patch 2/4. - move the related code from kernel/trace/bpf_trace.c to kernel/ events/core.c and add function perf_event_read_internal() to avoid poking inside of the event outside of perf code in Patch 3/4; - generial the func & map match-pair with an array in Patch 3/4; changes in V5: - move struct fd_array_map_ops* fd_ops to bpf_map; - move array perf event decrement refcnt function to map_free; - fix the NULL ptr of perf_event_get(); - move bpf_perf_event_read() to kernel/bpf/bpf_trace.c; - get rid of the remaining struct bpf_prog; - move the unnecessay cast on void *; changes in V4: - make the bpf_prog_array_map more generic; - fix the bug of event refcnt leak; - use more useful errno in bpf_perf_event_read(); changes in V3: - collapse V2 patches 1-3 into one; - drop the function map->ops->map_traverse_elem() and release the struct perf_event in map_free; - only allow to access bpf_perf_event_read() from programs; - update the perf_event_array_map elem via xchg(); - pass index directly to bpf_perf_event_read() instead of MAP_KEY; changes in V2: - put atomic_long_inc_not_zero() between fdget() and fdput(); - limit the event type to PERF_TYPE_RAW and PERF_TYPE_HARDWARE; - Only read the event counter on current CPU or on current process; - add new map type BPF_MAP_TYPE_PERF_EVENT_ARRAY to store the pointer to the struct perf_event; - according to the perf_event_map_fd and key, the function bpf_perf_event_read() can get the Hardware PMU counter value; Patch 5/5 is a simple example and shows how to use this new eBPF programs ability. The PMU counter data can be found in /sys/kernel/debug/tracing/trace(trace_pipe).(the cycles PMU value when 'kprobe/sys_write' sampling) $ cat /sys/kernel/debug/tracing/trace_pipe $ ./tracex6 ... syslog-ng-548 [000] d..1 76.905673: : CPU-0 681765271 syslog-ng-548 [000] d..1 76.905690: : CPU-0 681787855 syslog-ng-548 [000] d..1 76.905707: : CPU-0 681810504 syslog-ng-548 [000] d..1 76.905725: : CPU-0 681834771 syslog-ng-548 [000] d..1 76.905745: : CPU-0 681859519 syslog-ng-548 [000] d..1 76.905766: : CPU-0 681890419 syslog-ng-548 [000] d..1 76.905783: : CPU-0 681914045 syslog-ng-548 [000] d..1 76.905800: : CPU-0 681935950 syslog-ng-548 [000] d..1 76.905816: : CPU-0 681958299 ls-690 [005] d..1 82.241308: : CPU-5 3138451 sh-691 [004] d..1 82.244570: : CPU-4 7324988 <...>-699 [007] d..1 99.961387: : CPU-7 3194027 <...>-695 [003] d..1 99.961474: : CPU-3 288901 <...>-695 [003] d..1 99.961541: : CPU-3 383145 <...>-695 [003] d..1 99.961591: : CPU-3 450365 <...>-695 [003] d..1 99.961639: : CPU-3 515751 <...>-695 [003] d..1 99.961686: : CPU-3 579047 ... The detail of patches is as follow: Patch 1/5 add the necessary core perf APIs perf_event_attrs(), perf_event_get(),perf_event_read_local() when accessing events counters in eBPF programs Patch 2/5 rewrites part of the bpf_prog_array map code and make it more generic; Patch 3/5 introduces a new bpf map type. This map only stores the pointer to struct perf_event; Patch 4/5 implements function bpf_perf_event_read() that get the selected hardware PMU conuter; Patch 5/5 gives a simple example. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kaixu Xia authored
This is a simple example and shows how to use the new ability to get the selected Hardware PMU counter value. Signed-off-by: Kaixu Xia <xiakaixu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kaixu Xia authored
According to the perf_event_map_fd and index, the function bpf_perf_event_read() can convert the corresponding map value to the pointer to struct perf_event and return the Hardware PMU counter value. Signed-off-by: Kaixu Xia <xiakaixu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kaixu Xia authored
Introduce a new bpf map type 'BPF_MAP_TYPE_PERF_EVENT_ARRAY'. This map only stores the pointer to struct perf_event. The user space event FDs from perf_event_open() syscall are converted to the pointer to struct perf_event and stored in map. Signed-off-by: Kaixu Xia <xiakaixu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wang Nan authored
All the map backends are of generic nature. In order to avoid adding much special code into the eBPF core, rewrite part of the bpf_prog_array map code and make it more generic. So the new perf_event_array map type can reuse most of code with bpf_prog_array map and add fewer lines of special code. Signed-off-by: Wang Nan <wangnan0@huawei.com> Signed-off-by: Kaixu Xia <xiakaixu@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kaixu Xia authored
This patch add three core perf APIs: - perf_event_attrs(): export the struct perf_event_attr from struct perf_event; - perf_event_get(): get the struct perf_event from the given fd; - perf_event_read_local(): read the events counters active on the current CPU; These APIs are needed when accessing events counters in eBPF programs. The API perf_event_read_local() comes from Peter and I add the corresponding SOB. Signed-off-by: Kaixu Xia <xiakaixu@huawei.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Vivien Didelot says: ==================== net: dsa: mv88e6xxx: support switchdev FDB objects This patchset refactors the DSA and mv88e6xxx code to use the switchdev FDB objects. The first two patches add minor but necessary changes to switchdev, the third one implements the switchdev glue in DSA for FDB routines, and the remaining ones refactor the FDB access functions in the mv88e6xxx code. Below is an usage example (ports 0-2 belongs to br0, ports 3-4 belongs to br1): # bridge fdb add 3c:97:0e:11:30:6e dev swp2 # bridge fdb add 3c:97:0e:11:40:78 dev swp3 # bridge fdb add 3c:97:0e:11:50:86 dev swp4 # bridge fdb del 3c:97:0e:11:40:78 dev swp3 # bridge fdb 01:00:5e:00:00:01 dev eth0 self permanent 01:00:5e:00:00:01 dev eth1 self permanent 00:50:d2:10:78:15 dev swp0 master br0 permanent 3c:97:0e:11:30:6e dev swp2 self static 00:50:d2:10:78:15 dev swp3 master br1 permanent 3c:97:0e:11:50:86 dev swp4 self static # cat /sys/kernel/debug/dsa0/atu # DB T/P Vec State Addr # 001 Port 004 e 3c:97:0e:11:30:6e # 004 Port 010 e 3c:97:0e:11:50:86 For the 88E6xxx switches, FIDs 1 to num_ports will be reserved for non-bridged ports and bridge groups, and the remaining will be later used by VLANs. This change is necessary to welcome the support for hardware VLANs (which will follow soon). Changes in v2: - remove ndo_bridge_{get,set,del}link from switchdev/DSA glue code - use ether_addr_copy instead of memcpy for MAC addresses - constify MAC address in port_fdb_{add,del} - split the mv88e6xxx code refactoring into several patches ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-