Make sure to disable and deregister the switch on late probe errors to
avoid use-after-free when the device-resource-managed switch is freed.

Fixes: 14fceff4 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org>	# 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The X2 family of NICs (based on the SFC9250) have additional
MTD partitions for firmware and configuration. This includes
partitions that are read-only.

The NICs also have extended versions of the NVRAM interface,
allowing more detailed status information to be returned.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLS test cases recv_partial & recv_peek_large_buf_mult_recs expect to
receive a certain amount of data and then compare it against known
strings using memcmp. To prevent recvmsg() from returning lesser than
expected number of bytes (compared in memcmp), MSG_WAITALL needs to be
passed in recvmsg().
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When requesting the PHY driver module fails we'll bind the genphy
driver later. This isn't obvious to the user and may cause, depending
on the PHY, different types of issues. Therefore check the return code
of request_module(). Note that we only check for failures in loading
the module, not whether a module exists for the respective PHY ID.

v2:
- add comment explaining what is checked and what is not
- return error from phy_device_create() if loading module fails
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

 net/tls/tls_sw.c:1023:5: warning:
 symbol 'tls_sw_do_sendpage' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function sk_msg_clone has been modified to merge the data from source sg
entry to destination sg entry if the cloned data resides in same page
and is contiguous to the end entry of destination sk_msg. This improves
kernel tls throughput to the tune of 10%.

When the user space tls application calls sendmsg() with MSG_MORE, it leads
to calling sk_msg_clone() with new data being cloned placed continuous to
previously cloned data. Without this optimization, a new SG entry in
the destination sk_msg i.e. rec->msg_plaintext in tls_clone_plaintext_msg()
gets used. This leads to exhaustion of sg entries in rec->msg_plaintext
even before a full 16K of allowable record data is accumulated. Hence we
lose oppurtunity to encrypt and send a full 16K record.

With this patch, the kernel tls can accumulate full 16K of record data
irrespective of the size of data passed in sendmsg() with MSG_MORE.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = devm_kzalloc(dev, sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are already checking in phy_detach() that the PHY driver is of
generic kind (1G or 10G) and we are going to make use of that in the SFP
layer as well for 1000BaseT SFP modules, so expose helper functions to
return that information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: Split platform data to header file

This patch series decouples the DSA platform data structures from
net/dsa.h which was getting used for all sorts of DSA related
structures.

It would probably make sense for this series to go via David's net-next
tree to avoid conflicts on the ARM part, since we cannot obviously
include a header that does not yet exist.

No functional changes intended.
====================
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

b53 and mv88e6xxx support passing platform_data, and now that we have
split the platform_data portion from the main net/dsa.h header file,
include only the relevant parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have split the DSA platform data structures from the main
net/dsa.h header file, include only the relevant header file.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having net/dsa.h contain both the internal switch tree/driver
structures, split the relevant platform_data parts into
include/linux/platform_data/dsa.h and make that header be included by
net/dsa.h in order not to break any setup. A subsequent set of patches
will update code including net/dsa.h to include only the platform_data
header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to avoid frequent system interrupts when sending and
receiving packets. we replace disable_irq_nosync/enable_irq
with hinic_set_msix_state(), hinic_set_msix_state is used to
access memory mapped hinic devices.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 83c0afae ("net: dsa: Add new binding implementation"), DSA is
no longer a platform device exclusively and can support registering DSA
switches from other bus drivers (PCI, USB, I2C, etc.).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = kvzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:

instance = kvzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no need to and one shouldn't include asm/irq.h directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some time ago phydev_info() and friends have been added. They allow to
improve and simplify logging.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This workaround attempt helped for some but not all affected users.
With commit 11287b69 ("r8169: load Realtek PHY driver module
before r8169") we have a better workaround now, so we an remove
the first attempt.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: flower: improve flower resilience

This series contains mostly changes which improve nfp flower
offload's resilience, but are too large or risky to push into net.

Fred makes the driver waits for flower FW responses uninterruptible,
and a little longer (~40ms).

Pieter adds support for cards with multiple rule memories.

John reworks the MAC offloads.  He says:
> When potential tunnel end-point MACs are offloaded, they are assigned an
> index. This index may be associated with a port number meaning that if a
> packet matches an offloaded MAC address on the card, then the ingress
> port for that MAC can also be verified. In the case of shared MACs (e.g.
> on a linux bond) there may be situations where this index maps to only
> one of the ports that share the MAC.
>
> The idea of 'global' MAC indexes are supported that bypass the check on
> ingress port on the NFP. The patchset tracks shared MACs and assigns
> global indexes to these. It also ensures that port based indexes are
> re-applied if a single port becomes the only user of an offloaded MAC.
>
> Other patches in the set aim to tidy code without changing functionality.
> There is also a delete offload message introduced to ensure that MACs no
> longer in use in kernel space are removed from the firmware lookup tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A MAC address is not necessarily a unique identifier for a netdev. Drivers
such as Linux bonds, for example, can apply the same MAC address to the
upper layer device and all lower layer devices.

NFP MAC offload for tunnel decap includes port verification for reprs but
also supports the offload of non-repr MAC addresses by assigning 'global'
indexes to these. This means that the FW will not verify the incoming port
of a packet matching this destination MAC.

Modify the MAC offload logic to assign global indexes based on MAC address
instead of net device (as it currently does). Use this to allow multiple
devices to share the same MAC. In other words, if a repr shares its MAC
address with another device then give the offloaded MAC a global index
rather than associate it with an ingress port. Track this so that changes
can be reverted as MACs stop being shared.

Implement this by removing the current list based assignment of global
indexes and replacing it with an rhashtable that maps an offloaded MAC
address to the number of devices sharing it, distributing global indexes
based on this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is possible to receive a MAC address change notification without the
net device being down (e.g. when an OvS bridge is assigned the same MAC as
a port added to it). This means that an offloaded MAC address may not be
removed if its device gets a new address.

Maintain a record of the offloaded MAC addresses for each repr and netdev
assigned a MAC offload index. Use this to delete the (now expired) MAC if
a change of address event occurs. Only handle change address events if the
device is already up - if not then the netdev up event will handle it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFP repr netdevs contain private data that can store per port information.
In certain cases, the NFP driver offloads information from non-repr ports
(e.g. tunnel ports). As the driver does not have control over non-repr
netdevs, it cannot add/track private data directly to the netdev struct.

Add infastructure to store private information on any non-repr netdev that
is offloaded at a given time. This is used in a following patch to track
offloaded MAC addresses for non-reprs and enable correct house keeping on
address changes.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a potential tunnel end point goes down then its MAC address should
not be matchable on the NFP.

Implement a delete message for offloaded MACs and call this on net device
down. While at it, remove the actions on register and unregister netdev
events. A MAC should only be offloaded if the device is up. Note that the
netdev notifier will replay any notifications for UP devices on
registration so NFP can still offload ports that exist before the driver
is loaded. Similarly, devices need to go down before they can be
unregistered so removal of offloaded MACs is only required on down events.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Potential MAC destination addresses for tunnel end-points are offloaded to
firmware. This was done by building a list of such MACs and writing to
firmware as blocks of addresses.

Simplify this code by removing the list format and sending a new message
for each offloaded MAC.

This is in preparation for delete MAC messages. There will be one delete
flag per message so we cannot assume that this applies to all addresses
in a list.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently MAC addresses of all repr netdevs, along with selected non-NFP
controlled netdevs, are offloaded to FW as potential tunnel end-points.
However, the addresses of VF and PF reprs are meaningless outside of
internal communication and it is only those of physical port reprs
required.

Modify the MAC address offload selection code to ignore VF/PF repr devs.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent additions to the flower app private data have grouped the variables
of a given feature into a struct and added that struct to the main private
data struct.

In keeping with this, move all tunnel related private data to their own
struct. This has no affect on functionality but improves readability and
maintenance of the code.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.

Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The declaration of variable 'found' is one level too deep, fix this by
removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are various lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix over 100 documentation warnings in snmp_counter.rst by
extending the underline string lengths and inserting a blank line
after bullet items.

Examples:

Documentation/networking/snmp_counter.rst:1: WARNING: Title overline too short.
Documentation/networking/snmp_counter.rst:14: WARNING: Bullet list ends without a blank line; unexpected unindent.

Fixes: 2b965472 ("add document for TCP OFO, PAWS and skip ACK counters")
Fixes: 8e2ea53a ("add snmp counters document")
Fixes: 712ee16c ("add documents for snmp counters")
Fixes: 80cc4950 ("net: Add part of TCP counts explanations in snmp_counters.rst")
Fixes: b08794a9 ("documentation of some IP/ICMP snmp counters")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: yupeng <yupeng0921@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch bindings for spi managed mode are using spaces instead of tabs.
Fix them to get a file with a proper kernel indentation style.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Found by scripts/checkpatch.pl
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>