Changing CQ-Doorbell(DB) logic to prevent DB floods, it is supposed to be
pressed only if any hw CQE is polled. If cq-arm was requested
previously then don't bother about number of hw CQEs polled and
arm the CQ.
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Some versions of the FW sends wrong QP or CQ IDs in the
Async CQE. Adding a check to see whether qp or cq structures
associated with the CQE is valid.
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

debugfs_remove should be called before freeing the driver
stats resources to avoid any crash during ocrdma_remove.
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

ocrdma_dev_list is not used by the driver. So removing
the references of this variable. dev->rcu was introduced
for the ipv6 notifier for GID management. This is no longer
required as the GID management is outside the HW driver.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The ESTABLISHED event should have the peer's ord/ird so
swap the values in the event before the upcall.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When calculating the minimum ird in c4iw_accept_cr(), we need to always
have a value of at least 1 if the RTR message is a 0B read.  The code
was
incorrectly using ep->ord for this logic which was incorrectly adjusting
the ird and causing incorrect ord/ird negotiation when using MPAv2 to
negotiate these values.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

This allows client ULPs to get the negotiated ord/ird which is useful
to avoid stalling the SQ due to exceeding the ORD.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

In c4iw_create_listen(), if we're using listen filters, then bail out
of the busy loop if the device becomes fatally dead
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The INIT_UDATA() macro requires a pointer or unsigned long argument for
both input and output buffer, and all callers had a cast from when
the code was merged until a recent restructuring, so now we get

core/uverbs_cmd.c: In function 'ib_uverbs_create_cq':
core/uverbs_cmd.c:1481:66: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

This makes the code behave as before by adding back the cast to
unsigned long.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 565197dd ("IB/core: Extend ib_uverbs_create_cq")
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Casting a pointer to __be64 produces a warning on 32-bit architectures:

drivers/infiniband/hw/cxgb4/mem.c:147:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
    req->wr.wr_lo = (__force __be64)&wr_wait;

This was fixed at least twice for this driver in different places,
and accidentally reverted once more. This puts the correct version
back in place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6198dd8d ("iw_cxgb4: 32b platform fixes")
Signed-off-by: Doug Ledford <dledford@redhat.com>

IBA spec is now 1.3 not 3.1 and vol 1 should be mentioned
as there is also vol 2.
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Just fix a typo in the code comment.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Since kzalloc returns memory address, not error code,
it should be checked whether it is null or not.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Upinder hasn't worked for Cisco for a little while now, updating to more
active maintainers.
Signed-off-by: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Since ib_alloc_device returns allocated memory address, not error,
it should be checked as IS_NULL, not IS_ERR_OR_NULL.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Dave Goodell <dgoodell@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pick up the late fixes from the 4.3 cycle so we have them in our
next branch.

ib_send_cm_sidr_rep could sometimes erase the node from the sidr
(depending on errors in the process). Since ib_send_cm_sidr_rep is
called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv
could be either erased from the rb_tree twice or not erased at all.
Fixing that by making sure it's erased only once before freeing
cm_id_priv.

Fixes: a977049d ('[PATCH] IB: Add the kernel CM implementation')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When discussing the patches to demux ids in rdma_cm instead of ib_cm, it
was decided that it is best to use the P_Key value in the packet headers.
However, the mlx5 and ipath drivers are currently unable to send correct
P_Key values in GMP headers. They always send using a single P_Key that is
set during the GSI QP initialization.

Change the rdma_cm code to look at the P_Key value that is part of the
packet payload as a workaround. Once the drivers are fixed this patch can
be reverted.

Fixes: 4c21b5bc ("IB/cma: Add net_dev and private data checks to
RDMA CM")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Allocating a workqueue might fail, which wasn't checked so far and would
lead to NULL ptr derefs when an attempt to use it was made.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

If the lookup of a listening ID failed for an AF_IB request, the code
would try to call dev_put() on a NULL net_dev.

Fixes: be688195 ("IB/cma: Fix net_dev reference leak with failed
requests")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When using ifup/ifdown while executing enum_netdev_ipv4_ips,
ifa could become invalid and cause use after free error.
Fixing it by protecting with RCU lock.

Fixes: 03db3a2d ('IB/core: Add RoCE GID table management')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When ib_cache_gid_set_default_gid is called from several threads,
updating the table could make find_gid fail, therefore a negative
index will be retruned and an invalid table entry will be used.
Locking find_gid as well fixes this problem.

Fixes: 03db3a2d ('IB/core: Add RoCE GID table management')
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

When we leave the multicast group on expiration of a neighbor we
do not free the mcast structure. This results in a memory leak
that causes ib_dealloc_pd to fail and print a WARN_ON message
and backtrace.

Fixes: bd99b2e0 (IB/ipoib: Expire sendonly multicast joins)
Signed-off-by: Christoph Lameter <cl@linux.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The netdev checks recently added to RDMA CM expect a valid netdev to be
found for both InfiniBand and RoCE, but the code that find a netdev is
only implemented for InfiniBand.

Currently RoCE doesn't provide an API to find the netdev matching a
given set of parameters, so this patch just disables the netdev enforcement
for each incoming connections when the link layer is RoCE.

Fixes: 4c21b5bc ("IB/cma: Add net_dev and private data checks to RDMA CM")
Reported-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

There is no need to require LOCAL_DMA_LKEY support as the
PD allocation makes sure that there is a local_dma_lkey. Also
correctly set a return value in error path.

This caused a NULL pointer dereference in mlx5 which removed
the support for LOCAL_DMA_LKEY.

Fixes: bb6c96d7 ("xprtrdma: Replace global lkey with lkey local to PD")
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

The usnic_verbs kernel module was clearly marked with the following in
its code:

  MODULE_LICENSE("Dual BSD/GPL");

However, we accidentally left a few clauses of the BSD text out of the
license header in all the source files.  This commit fixes that: all
the files are properly dual BSD/GPL-licensed.  Contributors that might
have been confused by this have been contacted to get their permission
and are Cc:ed here.

Cc: Benoit Taine <benoit.taine@lip6.fr>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Michael Wang <yun.wang@profitbricks.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jeff Squyres <jsquyres@cisco.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Two enum members IB_DEVICE_RC_IP_CSUM and IB_DEVICE_RAW_IP_CSUM are
added to ib_device_cap_flags. Device should set these two flags if they support
insertion of UDP and TCP checksum on outgoing IPv4 messages and can verify the
validity of checksum for incoming IPv4 messages, for RC IPoIB and RAW over
Ethernet respectively. They are similar to IB_DEVICE_UD_IP_CSUM.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>

Pull x86 fixes from Thomas Gleixner:
 "Two bugfixes from Andy addressing at least some of the subtle NMI
  related wreckage which has been reported by Sasha Levin"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/nmi/64: Fix a paravirt stack-clobbering bug in the NMI code
  x86/paravirt: Replace the paravirt nop with a bona fide empty function

Pull irq fix from Thomass Gleixner:
 "A bugfix for the atmel aic5 irq chip driver which caches the wrong
  data and thereby breaking resume"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/atmel-aic5: Use per chip mask caches in mask/unmask()

Pull ARM fixes from Russell King:
 "Just two fixes: wire up the new system calls added during the last
  merge window, and fix another user access site"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: alignment: fix alignment handling for uaccess changes
  ARM: wire up new syscalls

Pull ARM SoC fixes from Olof Johansson:
 "Our first real batch of fixes this release cycle.  Nothing really
  concerning, and diffstat is a bit inflated due to some DT contents
  moving around on STi platforms.

  There's a collection of them here:

   - A fixup for a build breakage that hits on arm64 allmodconfig in
     QCOM SCM firmware drivers
   - MMC fixes for OMAP that had quite a bit of breakage this merge
     window.
   - Misc build/warning fixes on PXA and OMAP
   - A couple of minor fixes for Beagleboard X15 which is now starting
     to see a few more users in the wild"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
  ARM: sti: dt: adapt DT to fix probe/bind issues in DRM driver
  ARM: dts: fix omap2+ address translation for pbias
  firmware: qcom: scm: Add function stubs for ARM64
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  ARM: pxa: balloon3: Fix build error
  ARM: dts: Fixup model name for HP t410 dts
  ARM: dts: DRA7: fix a typo in ethernet
  ARM: omap2plus_defconfig: make PCF857x built-in
  ARM: dts: Use ti,pbias compatible string for pbias
  ARM: OMAP5: Cleanup options for SoC only build
  ARM: DRA7: Select missing options for SoC only build
  ARM: OMAP2+: board-generic: Remove stale of_irq macros
  ARM: OMAP4+: PM: erratum is used by OMAP5 and DRA7 as well
  ARM: dts: omap3-igep: Move eth IRQ pinmux to IGEPv2 common dtsi
  ARM: dts: am57xx-beagle-x15: Add wakeup irq for mcp79410
  ARM: dts: am335x-phycore-som: Fix mpu voltage
  ...

Pull CIFS fixes from Steve French:
 "Four fixes from testing at the recent SMB3 Plugfest including two
  important authentication ones (one fixes authentication problems to
  some popular servers when clock times differ more than two hours
  between systems, the other fixes Kerberos authentication for SMB3)"

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  fix encryption error checks on mount
  [SMB3] Fix sec=krb5 on smb3 mounts
  cifs: use server timestamp for ntlmv2 authentication
  disabling oplocks/leases via module parm enable_oplocks broken for SMB3

ARM: pxa: fixes for v4.3

These fixes are mainly regression fixes triggered by irq changes,
common clock framework introduction and sound side-effect of
other platforms.

* tag 'pxa-fixes-v4.3' of https://github.com/rjarzmik/linux:
  ARM: pxa: balloon3: Fix build error
  ARM: pxa: ssp: Fix build error by removing originally incorrect DT binding
  ARM: pxa: fix DFI bus lockups on startup
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.3-rc cycle:

- Two more patches to fix most of the MMC regressions with the
  PBIAS regulator changes. At least two MMC driver related issues
  still seems to remain for omap3 legacy booting and omap4 duovero.
  Note that the dts changes depend on a recent regulator fix, and
  are based on the regulator commit now in mainline kernel

- Enable autoidle for am43xx clocks to prevent clocks from staying
  always on

- Fix i2c5 pinctrl offsets for omap5-uevm

- Enable PCA953X as that's needed for HDMI to work on omap5

- Update phy supplies for beagle x15 beta board

- Use palmas-usb for on beagle x15 to start using the related
  driver that recently got merged

* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: fix omap2+ address translation for pbias
  ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
  ARM: omap2plus_defconfig: enable GPIO_PCA953X
  ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
  ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
  ARM: dts: am57xx-beagle-x15: Update Phy supplies
  regulator: pbias: program pbias register offset in pbias driver
  ARM: omap2plus_defconfig: Enable MUSB DMA support
  ARM: DRA752: Add ID detect for ES2.0
  ARM: OMAP3: vc: fix 'or' always true warning
  ARM: OMAP2+: Fix booting if no timer parent clock is available
  ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - check the return value of platform_get_irq as signed int in xgene.

   - skip adf_dev_restore on virtual functions in qat.

   - fix double-free with backlogged requests in marvell_cesa"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  hwrng: xgene - fix handling platform_get_irq
  crypto: qat - VF should never trigger SBR on PH
  crypto: marvell - properly handle CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes a iser-target series from Jenny + Sagi @ Mellanox that
  addresses the few remaining active I/O shutdown bugs, along with a
  patch to support zero-copy for immediate data payloads that gives a
  nice performance improvement for small block WRITEs.

  Also included are some recent >= v4.2 regression bug-fixes.  The most
  notable is a RCU conversion regression for SPC-3 PR registrations, and
  recent removal of obsolete RFC-3720 markers that introduced a login
  regression bug with MSFT iSCSI initiators.

  Thanks to everyone who has been testing + reporting bugs for v4.x"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target: Avoid OFMarker + IFMarker negotiation
  target: Make TCM_WRITE_PROTECT failure honor D_SENSE bit
  target: Fix target_sense_desc_format NULL pointer dereference
  target: Propigate backend read-only to core_tpg_add_lun
  target: Fix PR registration + APTPL RCU conversion regression
  iser-target: Skip data copy if all the command data comes as immediate
  iser-target: Change the recv buffers posting logic
  iser-target: Fix pending connections handling in target stack shutdown sequnce
  iser-target: Remove np_ prefix from isert_np members
  iser-target: Remove unused variables
  iser-target: Put the reference on commands waiting for unsol data
  iser-target: remove command with state ISTATE_REMOVE

Pull USB fixes from Greg KH:
 "Here are some USB driver fixes for 4.3-rc3.

  There's the usual assortment of new device ids, combined with xhci and
  gadget driver fixes.  Full details in the shortlog.  All of these have
  been in linux-next with no reported problems"

* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
  MAINTAINERS: remove amd5536udc USB gadget driver maintainer
  USB: whiteheat: fix potential null-deref at probe
  xhci: init command timeout timer earlier to avoid deleting it uninitialized
  xhci: change xhci 1.0 only restrictions to support xhci 1.1
  usb: xhci: exit early in xhci_setup_device() if we're halted or dying
  usb: xhci: stop everything on the first call to xhci_stop
  usb: xhci: Clear XHCI_STATE_DYING on start
  usb: xhci: lock mutex on xhci_stop
  xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
  xhci: give command abortion one more chance before killing xhci
  usb: Use the USB_SS_MULT() macro to get the burst multiplier.
  usb: dwc3: gadget: Fix BUG in RT config
  usb: musb: fix cppi channel teardown for isoch transfer
  usb: phy: isp1301: Export I2C module alias information
  usb: gadget: drop null test before destroy functions
  usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
  usb: gadget: dummy_hcd: fix rescan logic for transfer
  usb: gadget: dummy_hcd: fix unneeded else-if condition
  usb: gadget: dummy_hcd: emulate sending zlp in packet logic
  usb: musb: dsps: fix polling in device-only mode
  ...

Pull serial driver fix from Greg KH:
 "Here is one serial driver fix for 4.3-rc3 that resolves a module
  loading issue due to splitting up of the 8250 driver into smaller
  pieces.  It's been in linux-next with no reported problems"

* tag 'tty-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: Add missing module license for 8250_base.ko