- 02 Aug, 2013 40 commits
-
-
Dan Williams authored
commit 4cf76df0 upstream. Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other interface protocols are unknown. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Enrico Mioso authored
commit 3d1a69e7 upstream. Prevent the option driver from binding itself to the QMI/WWAN interface, making it unusable by the proper driver. Signed-off-by:
enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by:
-
Oleksij Rempel authored
commit d66eaf9f upstream. in some cases where device is attched to xhci port and do not responding, for example ath9k_htc with stalled firmware, kernel will crash on ring_doorbell_for_active_rings. This patch check if pointer exist before it is used. This patch should be backported to kernels as old as 2.6.35, that contain the commit e9df17eb "USB: xhci: Correct assumptions about number of rings per endpoint" Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
George Cherian authored
commit 07f3cb7c upstream. Xhci controllers with hci_version > 0.96 gives spurious success events on short packet completion. During webcam capture the "ERROR Transfer event TRB DMA ptr not part of current TD" was observed. The same application works fine with synopsis controllers hci_version 0.96. The same issue is seen with Intel Pantherpoint xhci controller. So enabling this quirk in xhci_gen_setup if controller verion is greater than 0.96. For xhci-pci move the quirk to much generic place xhci_gen_setup. Note from Sarah: The xHCI 1.0 spec changed how hardware handles short packets. The HW will notify SW of the TRB where the short packet occurred, and it will also give a successful status for the last TRB in a TD (the one with the IOC flag set). On the second successful status, that warning will be triggered in the driver. Software is now supposed to not assume the TD is not completed until it gets that last successful status. That means we have a slight race condition, although it should have little practical impact. This patch papers over that issue. It's on my long-term to-do list to fix this race condition, but it is a much more involved patch that will probably be too big for stable. This patch is needed for stable to avoid serious log spam. This patch should be backported to kernels as old as 3.0, that contain the commit ad808333 "Intel xhci: Ignore spurious successful event." The patch will have to be modified for kernels older than 3.2, since that kernel added the xhci_gen_setup function for xhci platform devices. The correct conflict resolution for kernels older than 3.2 is to set XHCI_SPURIOUS_SUCCESS in xhci_pci_quirks for all xHCI 1.0 hosts. Signed-off-by:
George Cherian <george.cherian@ti.com> Signed-off-by:
-
Sarah Sharp authored
commit 203a8661 upstream. When the host controller fails to respond to an Enable Slot command, and the host fails to respond to the register write to abort the command ring, the xHCI driver will assume the host is dead, and call usb_hc_died(). The USB device's slot_id is still set to zero, and the pointer stored at xhci->devs[0] will always be NULL. The call to xhci_check_args in xhci_free_dev should have caught the NULL virt_dev pointer. However, xhci_free_dev is designed to free the xhci_virt_device structures, even if the host is dead, so that we don't leak kernel memory. xhci_free_dev checks the return value from the generic xhci_check_args function. If the return value is -ENODEV, it carries on trying to free the virtual device. The issue is that xhci_check_args looks at the host controller state before it looks at the xhci_virt_device pointer. It will return -ENIVAL because the host is dead, and xhci_free_dev will ignore the return value, and happily dereference the NULL xhci_virt_device pointer. The fix is to make sure that xhci_check_args checks the xhci_virt_device pointer before it checks the host state. See https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1203453 for further details. This patch doesn't solve the underlying issue, but will ensure we don't see any more NULL pointer dereferences because of the issue. This patch should be backported to kernels as old as 3.1, that contain the commit 7bd89b40 "xhci: Don't submit commands or URBs to halted hosts." Signed-off-by:
Vincent Thiele <vincentthiele@gmail.com> Signed-off-by:
-
Enrico Mioso authored
commit 63b5df96 upstream. This patch adds support for the ONYX 3G device (version 1) from ALFA NETWORK. Signed-off-by:
-
Johan Hovold authored
commit 1fad5642 upstream. The driver failed to take the dynamic ids into account when determining the device type and therefore all devices were detected as 2-port devices when using the dynamic-id interface. Match on the usb-serial-driver field instead of doing redundant id-table searches. Reported-by:
Anders Hammarquist <iko@iko.pp.se> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Anton Blanchard authored
commit 0e0ed640 upstream. Module CRCs are implemented as absolute symbols that get resolved by a linker script. We build an intermediate .o that contains an unresolved symbol for each CRC. genksysms parses this .o, calculates the CRCs and writes a linker script that "resolves" the symbols to the calculated CRC. Unfortunately the ppc64 relocatable kernel sees these CRCs as symbols that need relocating and relocates them at boot. Commit d4703aef (module: handle ppc64 relocating kcrctabs when CONFIG_RELOCATABLE=y) added a hook to reverse the bogus relocations. Part of this patch created a symbol at 0x0: # head -2 /proc/kallsyms 0000000000000000 T reloc_start c000000000000000 T .__start This reloc_start symbol is causing lots of confusion to perf. It thinks reloc_start is a massive function that stretches from 0x0 to 0xc000000000000000 and we get various cryptic errors out of perf, including: problem incrementing symbol count, skipping event This patch removes the reloc_start linker script label and instead defines it as PHYSICAL_START. We also need to wrap it with CONFIG_PPC64 because the ppc32 kernel can set a non zero PHYSICAL_START at compile time and we wouldn't want to subtract it from the CRCs in that case. Signed-off-by:
Anton Blanchard <anton@samba.org> Acked-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Bjørn Mork authored
commit 94190301 upstream. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Ian Abbott authored
commit 4b18f08b upstream. `do_cmd_ioctl()` is called with the comedi device's mutex locked to process the `COMEDI_CMD` ioctl to set up comedi's asynchronous command handling on a comedi subdevice. `comedi_read()` and `comedi_write()` are the `read` and `write` handlers for the comedi device, but do not lock the mutex (for performance reasons, as some things can hold the mutex for quite a long time). There is a race condition if `comedi_read()` or `comedi_write()` is running at the same time and for the same file object and comedi subdevice as `do_cmd_ioctl()`. `do_cmd_ioctl()` sets the subdevice's `busy` pointer to the file object way before it sets the `SRF_RUNNING` flag in the subdevice's `runflags` member. `comedi_read() and `comedi_write()` check the subdevice's `busy` pointer is pointing to the current file object, then if the `SRF_RUNNING` flag is not set, will call `do_become_nonbusy()` to shut down the asyncronous command. Bad things can happen if the asynchronous command is being shutdown and set up at the same time. To prevent the race, don't set the `busy` pointer until after the `SRF_RUNNING` flag has been set. Also, make sure the mutex is held in `comedi_read()` and `comedi_write()` while calling `do_become_nonbusy()` in order to avoid moving the race condition to a point within that function. Change some error handling `goto cleanup` statements in `do_cmd_ioctl()` to simple `return -ERRFOO` statements as a result of changing when the `busy` pointer is set. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Ian Abbott authored
commit 69acbaac upstream. Comedi devices can do blocking read() or write() (or poll()) if an asynchronous command has been set up, blocking for data (for read()) or buffer space (for write()). Various events associated with the asynchronous command will wake up the blocked reader or writer (or poller). It is also possible to force the asynchronous command to terminate by issuing a `COMEDI_CANCEL` ioctl. That shuts down the asynchronous command, but does not currently wake up the blocked reader or writer (or poller). If the blocked task could be woken up, it would see that the command is no longer active and return. The caller of the `COMEDI_CANCEL` ioctl could attempt to wake up the blocked task by sending a signal, but that's a nasty workaround. Change `do_cancel_ioctl()` to wake up the wait queue after it returns from `do_cancel()`. `do_cancel()` can propagate an error return value from the low-level comedi driver's cancel routine, but it always shuts the command down regardless, so `do_cancel_ioctl()` can wake up he wait queue regardless of the return value from `do_cancel()`. Signed-off-by:
-
Alexandr \\\"Sky\\\" Ivanov authored
commit ca247635 upstream. Adding support for D-Link DWM-152/C1 and DWM-156/C1 devices. DWM-152/C1: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=07d1 ProdID=3e01 Rev= 0.00 S: Product=USB Configuration S: SerialNumber=1234567890ABCDEF C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms DWM-156/C1: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=07d1 ProdID=3e02 Rev= 0.00 S: Product=DataCard Device S: SerialNumber=1234567890ABCDEF C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms I:* If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Alexandr Ivanov <alexandr.sky@gmail.com> Signed-off-by:
-
Harshula Jayasuriya authored
commit e4daf1ff upstream. The following call chain: ------------------------------------------------------------ nfs4_get_vfs_file - nfsd_open - dentry_open - do_dentry_open - __get_file_write_access - get_write_access - return atomic_inc_unless_negative(&inode->i_writecount) ? 0 : -ETXTBSY; ------------------------------------------------------------ can result in the following state: ------------------------------------------------------------ struct nfs4_file { ... fi_fds = {0xffff880c1fa65c80, 0xffffffffffffffe6, 0x0}, fi_access = {{ counter = 0x1 }, { counter = 0x0 }}, ... ------------------------------------------------------------ 1) First time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NULL, hence nfsd_open() is called where we get status set to an error and fp->fi_fds[O_WRONLY] to -ETXTBSY. Thus we do not reach nfs4_file_get_access() and fi_access[O_WRONLY] is not incremented. 2) Second time around, in nfs4_get_vfs_file() fp->fi_fds[O_WRONLY] is NOT NULL (-ETXTBSY), so nfsd_open() is NOT called, but nfs4_file_get_access() IS called and fi_access[O_WRONLY] is incremented. Thus we leave a landmine in the form of the nfs4_file data structure in an incorrect state. 3) Eventually, when __nfs4_file_put_access() is called it finds fi_access[O_WRONLY] being non-zero, it decrements it and calls nfs4_file_put_fd() which tries to fput -ETXTBSY. ------------------------------------------------------------ ... [exception RIP: fput+0x9] RIP: ffffffff81177fa9 RSP: ffff88062e365c90 RFLAGS: 00010282 RAX: ffff880c2b3d99cc RBX: ffff880c2b3d9978 RCX: 0000000000000002 RDX: dead000000100101 RSI: 0000000000000001 RDI: ffffffffffffffe6 RBP: ffff88062e365c90 R8: ffff88041fe797d8 R9: ffff88062e365d58 R10: 0000000000000008 R11: 0000000000000000 R12: 0000000000000001 R13: 0000000000000007 R14: 0000000000000000 R15: 0000000000000000 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #9 [ffff88062e365c98] __nfs4_file_put_access at ffffffffa0562334 [nfsd] #10 [ffff88062e365cc8] nfs4_file_put_access at ffffffffa05623ab [nfsd] #11 [ffff88062e365ce8] free_generic_stateid at ffffffffa056634d [nfsd] #12 [ffff88062e365d18] release_open_stateid at ffffffffa0566e4b [nfsd] #13 [ffff88062e365d38] nfsd4_close at ffffffffa0567401 [nfsd] #14 [ffff88062e365d88] nfsd4_proc_compound at ffffffffa0557f28 [nfsd] #15 [ffff88062e365dd8] nfsd_dispatch at ffffffffa054543e [nfsd] #16 [ffff88062e365e18] svc_process_common at ffffffffa04ba5a4 [sunrpc] #17 [ffff88062e365e98] svc_process at ffffffffa04babe0 [sunrpc] #18 [ffff88062e365eb8] nfsd at ffffffffa0545b62 [nfsd] #19 [ffff88062e365ee8] kthread at ffffffff81090886 #20 [ffff88062e365f48] kernel_thread at ffffffff8100c14a ------------------------------------------------------------ Signed-off-by:
Harshula Jayasuriya <harshula@redhat.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Ewan D. Milne authored
commit 085b513f upstream. sd_prep_fn will allocate a larger CDB for the command via mempool_alloc for devices using DIF type 2 protection. This CDB was being freed in sd_done, which results in a kernel crash if the command is retried due to a UNIT ATTENTION. This change moves the code to free the larger CDB into sd_unprep_fn instead, which is invoked after the request is complete. It is no longer necessary to call scsi_print_command separately for this case as the ->cmnd will no longer be NULL in the normal code path. Also removed conditional test for DIF type 2 when freeing the larger CDB because the protection_type could have been changed via sysfs while the command was executing. Signed-off-by:
Ewan D. Milne <emilne@redhat.com> Acked-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Saurav Kashyap authored
commit c3ccb1d7 upstream. This fixes a regression where Xyratex controllers and disks were lost by the driver: https://bugzilla.kernel.org/show_bug.cgi?id=59601Reported-by:
Jack Hill <jackhill@jackhill.us> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Jeff Skirvin authored
commit 96f15f29 upstream. This commit fixes a race condition in the isci driver abort task and SSP device task management path. The race is caused when an I/O termination in the SCU hardware is necessary because of an SSP target timeout condition, and the check of the I/O end state races against the HW-termination-driven end state. The failure of the race meant that no TMF was sent to the device to clean-up the pending I/O. Signed-off-by:
Jeff Skirvin <jeffrey.d.skirvin@intel.com> Reviewed-by:
Lukasz Dorau <lukasz.dorau@intel.com> Signed-off-by:
-
Mark Kettenis authored
commit cef1d00c upstream. Noticed that my old Radeon 7500 hung after printing drm: GPU not posted. posting now... when it wasn't selected as the primary card the BIOS. Some digging revealed that it was hanging in combios_parse_mmio_table() while parsing the ASIC INIT 3 table. Looking at the BIOS ROM for the card, it becomes obvious that there is no ASIC INIT 3 table in the BIOS. The code is just processing random garbage. No surprise it hangs! Why do I say that there is no ASIC INIT 3 table is the BIOS? This table is found through the MISC INFO table. The MISC INFO table can be found at offset 0x5e in the COMBIOS header. But the header is smaller than that. The COMBIOS header starts at offset 0x126. The standard PCI Data Structure (the bit that starts with 'PCIR') lives at offset 0x180. That means that the COMBIOS header can not be larger than 0x5a bytes and therefore cannot contain a MISC INFO table. I looked at a dozen or so BIOS images, some my own, some downloaded from: <http://www.techpowerup.com/vgabios/index.php?manufacturer=ATI&page=1> It is fairly obvious that the size of the COMBIOS header can be found at offset 0x6 of the header. Not sure if it is a 16-bit number or just an 8-bit number, but that doesn't really matter since the tables seems to be always smaller than 256 bytes. So I think combios_get_table_offset() should check if the requested table is present. This can be done by checking the offset against the size of the header. See the diff below. The diff is against the WIP OpenBSD codebase that roughly corresponds to Linux 3.8.13 at this point. But I don't think this bit of the code changed much since then. For what it is worth: Signed-off-by:
Mark Kettenis <kettenis@openbsd.org> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Alex Deucher authored
commit 03ed8cf9 upstream. Hopefully avoid more quirks in the future due to bogus vbios dac data. Signed-off-by:
-
Ondrej Zary authored
commit f7929f34 upstream. Hello, got another card with "too bright" problem: Sapphire Radeon VE 7000 DDR (VGA+S-Video) lspci -vnn: 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] [1002:5159] (prog-if 00 [VGA controller]) Subsystem: PC Partner Limited Sapphire Radeon VE 7000 DDR [174b:7c28] The patch below fixes the problem for this card. But I don't like the blacklist, couldn't some heuristic be used instead? The interesting thing is that the manufacturer is the same as the other card needing the same quirk. I wonder how many different types are broken this way. The "wrong" ps2_pdac_adj value that comes from BIOS on this card is 0x300. ==================== drm/radeon: Add primary dac adj quirk for Sapphire Radeon VE 7000 DDR Values from BIOS are wrong, causing too bright colors. Use default values instead. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Sami Rahman authored
commit 76811569 upstream. Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB devices using customized Silicon Labs' CP210x.c USB to UART bridge drivers with PIDs: 88A4, 88A5. Signed-off-by:
Sami Rahman <sami.rahman@mmbresearch.com> Tested-by:
-
Barry Grussling authored
commit b579fa52 upstream. This patch adds support for the Schweitzer Engineering Laboratories C662 USB cable based off the CP210x driver. Signed-off-by:
Barry Grussling <barry@grussling.com> Signed-off-by:
-
Daniil Bolsun authored
commit c38e83b6 upstream. This patch was tested on 3.10.1 kernel. Same models of Petatel NP10T modems have different device IDs. Unfortunately they have no additional revision information on a board which may treat them as different devices. Currently I've seen only two NP10T devices with various IDs. Possibly Petatel NP10T list will be appended upon devices with new IDs will appear. Signed-off-by:
Daniil Bolsun <dan.bolsun@gmail.com> Signed-off-by:
-
Jóhann B. Guðmundsson authored
commit 58fc90db upstream. Signed-off-by:
Jóhann B. Guðmundsson <johannbg@fedoraproject.org> Signed-off-by:
-
Ren Bigcren authored
commit e7a6121f upstream. The device report an error capacity when read_capacity_16(). Using read_capacity_10() can get the correct capacity. Signed-off-by:
Ren Bigcren <bigcren.ren@sonymobile.com> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by:
Oskar Andero <oskar.andero@sonymobile.com> Signed-off-by:
-
Luiz Angelo Daros de Luca authored
commit 90625070 upstream. This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series USB ID (0846:0110) to the cp210x driver. Without this, the serial adapter is not recognized in Linux. Description was obtained from an Netgear Eng. Signed-off-by:
Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by:
-
Eldad Zack authored
commit be2f93a4 upstream. Return SNDRV_PCM_POS_XRUN (snd_pcm_uframes_t) instead of SNDRV_PCM_STATE_XRUN (snd_pcm_state_t) from the pointer function of 6fire, as expected by snd_pcm_update_hw_ptr0(). Caught by sparse. Signed-off-by:
Eldad Zack <eldad@fogrefinery.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Josef Bacik authored
commit d29a9f62 upstream. If we stop dropping a root for whatever reason we need to add it back to the dead root list so that we will re-start the dropping next transaction commit. The other case this happens is if we recover a drop because we will add a root without adding it to the fs radix tree, so we can leak it's root and commit root extent buffer, adding this to the dead root list makes this cleanup happen. Thanks, Reported-by:
Alex Lyakas <alex.btrfs@zadarastorage.com> Signed-off-by:
Josef Bacik <jbacik@fusionio.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Josef Bacik authored
commit fec386ac upstream. We aren't setting path->locks[level] when we resume a snapshot deletion which means we won't unlock the buffer when we free the path. This causes deadlocks if we happen to re-allocate the block before we've evicted the extent buffer from cache. Thanks, Reported-by:
-
Youquan Song authored
commit eac27f04 upstream. There is a patch b55f84e2 "ata_piix: Fix DVD not dectected at some Haswell platforms" to fix an issue of DVD not recognized on Haswell Desktop platform with Lynx Point. Recently, it is also found the same issue at some platformas with Wellsburg PCH. So deliver a similar patch to fix it by disables 32bit PIO in IDE mode. Signed-off-by:
Youquan Song <youquan.song@intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Aaron Plattner authored
commit d52392b1 upstream. Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip. Reviewed-by:
Andy Ritger <aritger@nvidia.com> Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
-
Aaron Plattner authored
commit 7ae48b56 upstream. Vendor ID 0x10de0051 is used by a yet-to-be-named GPU chip. Signed-off-by:
Daniel Dadap <ddadap@nvidia.com> Signed-off-by:
-
Takashi Iwai authored
commit 86f0b5b8 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 61be2b9a upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Takashi Iwai authored
commit 46f6c1aa upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
-
Takashi Iwai authored
commit 5be1efb4 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 9538aa46 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Acked-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Chih-Chung Chang authored
commit cb6f66a2 upstream. The registers of max98088 are 8 bits, not 16 bits. This bug causes the contents of registers to be overwritten with bad values when the codec is suspended and then resumed. Signed-off-by:
Chih-Chung Chang <chihchung@chromium.org> Signed-off-by:
Dylan Reid <dgreid@chromium.org> Signed-off-by:
-
Takashi Iwai authored
commit 5b9ab3f7 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit cc7282b8 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
Takashi Iwai authored
commit 60478295 upstream. snd_pcm_stop() must be called in the PCM substream lock context. Signed-off-by:
-
![Alexandr \\\"Sky\\\" Ivanov's avatar](https://secure.gravatar.com/avatar/dabfd77a895665bf8b3c6da6e021895d?s=80&d=identicon "Alexandr \\\\"Sky\\\\" Ivanov")
