- 12 Jun, 2013 40 commits
-
-
Hante Meuleman authored
When credit borrowing is active the BE credits have been depleted, however the worker should still be scheduled. In case of credit borrowing correct credit map to make sure worker remains active. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Hante Meuleman authored
Store gen bit on suppressed packet per entry and use latest stored version for each packet which gets transmitted to fw. Reviewed-by:
-
Hante Meuleman authored
Currently on a bus flow control both fws is informed and netif queue gets closed. In case of fw signalling enabled, let the flow control be handled by fw signalling only. Reviewed-by:
-
Arend van Spriel authored
The debug logging in firmware-signalling code was rather extensive and for a large part in the data path. This patch removes large part or the level is changed to DATA level. Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Firmware can request the driver for transmit packets using two different signals. Only for one signal a flag was set in the sk_buff control buffer. This patch adds explicit flag for the other signal as well. Reviewed-by:
-
Arend van Spriel authored
Reworked brcmf_skb_pick_up_credit() so it can be used for both fcmode flavours in the same way. Reviewed-by:
-
Hante Meuleman authored
On bus flow control (no more host bus resources to send packets to device) the netif flow control was toggled, however credit management should also take this status into account. Since there are multiple sources handling this flow control necessary spinlocks were added to protect flow control related data/states. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
The brcmf_skbuff_cb structure contain if_flags and htod fields. Both have a bitfield defined to hold the fifo number. With a small code change we get rid of the fifo bitfield in if_flags. Reviewed-by:
-
Arend van Spriel authored
The firmware-signal API specification defines length for the different tlv. During testing on different devices it turned out not all firmware used the tlv length according specification. Therefore the length check is made less strict with this patch. Reviewed-by:
-
Gabor Juhos authored
It is exactly the same like the generic rt2800usb_ops. Remove the duplicate and use the generic ops for all devices. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Gabor Juhos authored
The extra_tx_headroom field of struct rt2x00_ops indicates the extra TX headroom size required for a given device. This data is redundant, the value can be computed from the desc_size and winfo_size fields of the TX queues. Move the extra_tx_headroom field to struct rt2x00_dev, compute its value in the probe routine and use the cached value in the rest of the code. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
-
Luis R. Rodriguez authored
This adds VHT80 support for the QCA world regulatory domains. Cc: kvalo@qca.qualcomm.com Signed-off-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by:
-
Wei Yongjun authored
Fix to return a negative error code in the il3945_hw_set_hw_params() error handling case instead of 0, as done elsewhere in this function. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by:
-
Avinash Patil authored
This patch disables tx_amsdu support in mwifiex by default. tx_amdsu support can be enabled via module parameter at load time. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
PATCH "mwifiex: scan delay timer cleanup in unload path" adds code to cancel scan delay timer in unload path. It causes a regression for USB interface. USB8797 card gets enumerated twice. First enumeration is for firmware download and second enumeration expects firmware initialization. It was observed that we are trying del_timer_sync() without setting up the timer when remove handler is called after first enumeration. This patch moves setup_timer() call to appropriate place so that timer is setup for both the enumerations. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Gabor Juhos authored
If the queue_init callback is implemented by a driver it gets used instead of the data_queue_desc based initialization. The queue_init callback is implemented for each drivers now, so the old initialization method is not used anymore. Remove the unused data_queue_desc structure and all of the related code. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Compile tested only. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Signed-off-by:
Jakub Kicinski <kubakici@wp.pl> Acked-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Compile tested only. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Compile tested only. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. Signed-off-by:
-
Gabor Juhos authored
The generic rt2x00 code has been changed to allow the drivers toimplement dynamic data_queue initialization. Remove the static data queue descriptor structures and implement the queue_init callback instead. The actual chipset is already known when the callback is used. This allows us to use a single callback for all supported devices. Signed-off-by:
-
Gabor Juhos authored
The driver uses static data structures for initializing specific fields of a given data queue. These static queue data descriptor structures are containing values which related to a given chipset. Even though the values are chip specific, the actual selection of the used structure is based on device specific vendor/product identifiers. This approach works, but it is not always reliable. Sometimes the vendor and/or device IDs of the PCI and USB devices contains improper values which makes it impossible to select the correct structure for such devices. The patch adds a new callback to tr2x00_ops which is called after the chipset detection is finished. This allows the drivers to do dynamic initialization of the data_queue structure for a given queue based on the actual chipset. After each driver implements the queue_init callback, the data_queue_desc structure will be removed. Signed-off-by:
-
Gabor Juhos authored
Use the queue->limit value instead of the qdesc->entry_num to compute the threshold. The two source values are the same and the data queue descriptor structure will be removed by a later patch. Also separate the computation from the rest of the init code to make further changes easier. Signed-off-by:
-
Gabor Juhos authored
The beacon data queue is initialized already, so fetch the number of the queue entries from that instead of using the entry_num field of the data queue descriptor. The two values are the same, and the use of the rt2x00dev->bcn->limit value allows us to get rid of a superfluous pointer dereference. Signed-off-by:
-
Gabor Juhos authored
The qdesc parameter is not used anymore, so remove that. Signed-off-by:
-
Gabor Juhos authored
Add a new field into struct data_queue and store the size of the per-queue_entry private data in that. Additionally, use the new field in the rt2x00queue_alloc_entries function to compute the size of the queue entries for a given queue. The patch does not change the current behaviour but makes it possible to remove the queue_desc parameter of the rt2x00queue_alloc_entries function. That will be done by a subsequent patch. Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Sujith Manoharan authored
The phy error mask registers are programmed already in ath9k_ani_restart(), so there is no need to set them in ath9k_ani_reset(). Signed-off-by:
-
Sujith Manoharan authored
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters" removed code setting various phy registers holding threshold values. This is likely required for OFDM weak signal detection to function correctly, so add them, but skip AR9462 and AR9565. Signed-off-by:
-
Sujith Manoharan authored
The commit, "ath9k_hw: improve ANI processing and rx desensitizing parameters" modified the immunity level tables for both CCK and OFDM. Fix them so that the tables are in sync with the internal driver/codebase. Signed-off-by:
-
Sujith Manoharan authored
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters" changed various ANI operational parameters to address a specific card/environment. This is not really applicable for other cards in general usage. As per internal documentation, lowering the immunity level can be done only after 5 periods have passed and the CCK/OFDM errors are below the low watermak threshold - which have been fixed at 300 and 400 respectively by the sytems team. Raising the immunity level can be done when CCK/OFDM errors exceed 600 and 1000 (per second). Set these values once during attach. Signed-off-by:
-
Sujith Manoharan authored
The commit "ath9k_hw: improve ANI processing and rx desensitizing parameters" changed the OFDM weak signal detection logic to disable it for AP mode, which is not allowed. Fix this and enable it always for AP mode. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessJohn W. Linville authored
Conflicts: drivers/net/wireless/ath/ath9k/Kconfig net/mac80211/iface.c
-
Kees Cook authored
The module parameter "fwpostfix" is userspace controllable, unfiltered, and is used to define the firmware filename. b43_do_request_fw() populates ctx->errors[] on error, containing the firmware filename. b43err() parses its arguments as a format string. For systems with b43 hardware, this could lead to a uid-0 to ring-0 escalation. CVE-2013-2852 Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Sujith Manoharan authored
The ath9k rate control algorithm has various architectural issues that make it a poor fit in scenarios like congested environments etc. An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191 Change the default to minstrel which is more robust in such cases. The ath9k RC code is left in the driver for now, maybe it can be removed altogether later on. Cc: stable@vger.kernel.org Cc: Jouni Malinen <jouni@qca.qualcomm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Felix Fietkau authored
This reverts commit 68d9e1fa This change reduces rx sensitivity with no apparent extra benefit. It looks like it was meant for testing in a specific scenario, but it was never properly validated. Cc: rmanohar@qca.qualcomm.com Cc: stable@vger.kernel.org Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Sujith Manoharan authored
Almost all the DMA issues which have plagued ath9k (in station mode) for years are related to PS. Disabling PS usually "fixes" the user's connection stablility. Reports of DMA problems are still trickling in and are sitting in the kernel bugzilla. Until the PS code in ath9k is given a thorough review, disbale it by default. The slight increase in chip power consumption is a small price to pay for improved link stability. Cc: stable@vger.kernel.org Signed-off-by:
-
Yijing Wang authored
Fix build error for il_pm_ops if CONFIG_PM is set but CONFIG_PM_SLEEP is not set. ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined! ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined! make[1]: *** [__modpost] Error 1 make: *** [modules] Error 2 Signed-off-by:
Yijing Wang <wangyijing@huawei.com> Cc: Stanislaw Gruszka <sgruszka@redhat.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: netdev@vger.kernel.org Cc: linux-wireless@vger.kernel.org Cc: Jingoo Han <jg1.han@samsung.com> Acked-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
