Signed-off-by: Mikko Rapeli <mikko.rapeli@teleca.com>
Tested-by: Bart Champagne <bart@as35701.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

commit 29dd5975 ("ide: remove ide_setup_ports")
forgot to take into account the base addresses for the CONTROL registers for
falconide and macide, as pointed out by Michael Schmitz.

Falconide was tested on Aranym.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  RDMA/nes: Fix possible array overrun
  RDMA/nes: Fix VLAN support
  RDMA/nes: Fix MAC interrupt erroneously masked on ifdown
  IB: Fix return value in ib_device_register_sysfs()

* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
  x86: fix lguest build failure
  x86: reenable support for system without on node0
  x86: CPA: avoid double checking of alias ranges
  x86: CPA no alias checking for _NX
  x86: zap invalid and unused pmds in early boot
  x86: CPA, fix alias checks

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (59 commits)
  V4L/DVB (7219): zoran: Fix namespace conflicts with Zoran 'GPIO_MAX' enum
  V4L/DVB (7205): tuner-xc2028 depends on FW_LOADER
  V4L/DVB (7201): cx88-mpeg: Fix race condition in variable access
  V4L/DVB (7200): Fix FM firmware loading
  V4L/DVB (7198): V4L, include ioctl.h in videodev headers
  V4L/DVB (7197): bttv: Fix overlay divide error
  V4L/DVB (7195): xc5000: fix build error when built as module
  V4L/DVB (7194): cx88-mpeg: Allow concurrent access to cx88-mpeg devices
  V4L/DVB (7193): tveeprom: Add proper tuner mapping for hauppauge eeprom id 133
  V4L/DVB (7192): Adds support for Genius TVGo A11MCE
  V4L/DVB (7189): autosuspend support
  V4L/DVB (7188): radio-si470x version 1.0.6
  V4L/DVB (7186): tda10086: make the 22kHz tone for DISEQC a config option
  V4L/DVB (7183): radio-si470x: fix build warning
  V4L/DVB (7180): em28xx: add URB_NO_TRANSFER_DMA_MAP, since urb->transfer_dma is set
  V4L/DVB (7179): Allow more than one em28xx board
  V4L/DVB (7164): em28xx-alsa: Add a missing mutex
  V4L/DVB (7163): em28xx: makes audio settings more stable
  V4L/DVB (7162): em28xx: Fix endian and returns the correct values
  V4L/DVB (7161): em28xx: Fix printing debug values higher than 127
  ...

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] Added quota targets and removed dmapi directory
  [XFS] Fix up xfs out-of-tree builds. (a.k.a. external modules)
  [XFS] Remove Makefile wrappers in XFS

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  [CRYPTO] null: Add missing Kconfig dependency on BLKCIPHER
  [CRYPTO] tcrypt: Add missing Kconfig dependency on BLKCIPHER
  [HIFN]: Fix invalid config ifdefs for RNG support

* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
  timer_list: print relative expiry time signed

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kbuild: explain why DEBUG_SECTION_MISMATCH is UNDEFINED
  kbuild: fix building vmlinux.o
  kbuild: allow -fstack-protector to take effect
  kconfig: fix select in combination with default

drivers/lguest/x86/switcher_32.S:(.text+0x3815f8): 
	undefined reference to `LGUEST_PAGES_regs_trapnum'

This problem was caused by asm-offsets.c only having the offsets when
lguest *guest* support was set, not lguest host (host support used to
imply guest support, so now they're separate these bugs come out).

Lguest guest support and host support are separate config options:
they used to be tied together. Sort out which parts of asm-offsets are
needed for Guest and Host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

One system doesn't have RAM for node0 installed.

SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 1 PXM 1 0-a0000
SRAT: Node 1 PXM 1 0-dd000000
SRAT: Node 1 PXM 1 0-123000000
ACPI: SLIT: nodes = 2
 10 13
 13 10
mapped APIC to ffffffffff5fb000 (        fee00000)
Bootmem setup node 1 0000000000000000-0000000123000000
  NODE_DATA [000000000000e000 - 0000000000014fff]
  bootmap [0000000000015000 -  00000000000395ff] pages 25
Could not find start_pfn for node 0
Pid: 0, comm: swapper Not tainted 2.6.24-smp-g5a514e21-dirty #14

Call Trace:
 [<ffffffff80bab498>] free_area_init_node+0x22/0x381
 [<ffffffff8045ffc5>] generic_swap+0x0/0x17
 [<ffffffff80bab0cc>] find_zone_movable_pfns_for_nodes+0x54/0x271
 [<ffffffff80baba5f>] free_area_init_nodes+0x239/0x287
 [<ffffffff80ba6311>] paging_init+0x46/0x4c
 [<ffffffff80b9dda5>] setup_arch+0x3c3/0x44e
 [<ffffffff80b978be>] start_kernel+0x6f/0x2c7
 [<ffffffff80b971cc>] _sinittext+0x1cc/0x1d3

This happens because node 0 is not online, but the node state in
mm/page_alloc.c has node 0 set.

        nodemask_t node_states[NR_NODE_STATES] __read_mostly = {
                [N_POSSIBLE] = NODE_MASK_ALL,
                [N_ONLINE] = { { [0] = 1UL } },

So we need to clear node_online_map before initializing the memory.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

When the CPA code is called with an virtual address in the range of
the direct mapping or the high alias then we do not need to run
through the alias check for this range.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

NX settings are not required to be consistent across alias mappings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The early boot code maps KERNEL_TEXT_SIZE (currently 40MB) starting
from __START_KERNEL_map. The kernel itself only needs _text to _end
mapped in the high alias. On relocatible kernels the ASM setup code
adjusts the compile time created high mappings to the relocation. This
creates invalid pmd entries for negative offsets:

0xffffffff80000000 -> pmd entry: ffffffffff2001e3
It points outside of the physical address space and is marked present.

This starts at the virtual address __START_KERNEL_map and goes up to
the point where the first valid physical address (0x0) is mapped.

Zap the mappings before _text and after _end right away in early
boot. This removes also the invalid entries.

Furthermore it simplifies the range check for high aliases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

c_p_a() did not discover all aliases correctly. (such as when called
on vmalloc()-ed areas or ioremap()-ed areas)

Push the alias checks to the lower, physical level and consistently
discover all aliases that might exist: the low direct mappings and
the high linear kernel-text mappings (on 64-bit).

Thanks to Andi Kleen for pointing out that this was buggy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

In nes_create_qp(), the test

	if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {

is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as

	nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;

and mmap_nesqp is declared as

	struct nes_qp      *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];

which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS.  Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.

This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

Thanks to Martin Michlmayr <tbm@cyrius.com> for reporting this issue:

The zoran driver fails to compile on the ARM Orion platform with:

In file included from drivers/media/video/zoran_procfs.c:50:
drivers/media/video/zoran.h:232: error: expected identifier before numeric
constant

The reason is that drivers/media/video/zoran.h defines an enum with
GPIO_MAX in it, but Orion contains a #define GPIO_MAX 32 in
include/asm-arm/arch-orion/orion.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

There was a possible race condition in the increment/decrement of
the active device references counter.
Thanks to Trent Piepho (xyzzy@speakeasy.org) for bringing it up.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

There's no need to load SCode table for FM.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Fix compilation of user processes which includes videodev*.h but
not includes linux/ioctl.h:

v4l2ext_helper.c: In function 'process_ioctl':
v4l2ext_helper.c:183: warning: implicit declaration of function '_IOWR'
v4l2ext_helper.c:183: error: expected expression before 'struct'
v4l2ext_helper.c:183: error: case label does not reduce to an integer constant
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (e84619b1), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer.  This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x8879d): undefined reference to `xc5000_attach'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

It currently isn't possible to open the frontend device of cx88-mpeg devices
(DVB or Blackbird) multiple times concurrently. (for instance, to attach a
signal monitoring tool while reading a stream, or to send a frequency change
ioctl) This patch fixes that condition.
Signed-off-by: Roland Stoll <roland@xindex.de>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Do away with the need to set tuner=63 on cx88xx with recent HVR-1300 boards
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Adrian Pardini <pardo.bsso@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Together with Oliver Neukum from Novell, USB autosuspend support was added.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This patch combines all the finished discussions and its resulting patches from
the mailing list.

The version 1.0.6 is mainly influenced by Oliver Neukum. He found a lot of
small issues, that are fixed with this patch now. For me the most interesting
thing is, that it's now safer to use it on other architectures.

The history for version 1.0.6 is:
- fixed coverity checker warnings in *_usb_driver_disconnect
- probe()/open() race by correct ordering in probe()
- DMA coherency rules by separate allocation of all buffers
- use of endianness macros
- abuse of spinlock, replaced by mutex
- racy handling of timer in disconnect, replaced by delayed_work
- racy interruptible_sleep_on(), replaced with wait_event_interruptible()
- handle signals in read()

The driver is tested with all Debian/testing radio programs and rdsd. The patch
is tested against checkpatch.pl v1.12.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.

This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

fix the following build warning:

radio-si470x.c: In function 'si470x_get_rds_registers':
radio-si470x.c:562: warning: format '%ld' expects type 'long int',
		    but argument 3 has type 'unsigned int'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Alan Stern <stern@rowland.harvard.edu> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.

Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=480/800 us (60%), #Int=  0, #Iso=  2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1

So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=232/800 us (29%), #Int=  0, #Iso=  2
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1

So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Improves audio configurations on em28xx:
        - mutes audio before changing amux;
        - adds a delay after setting audio src;
        - waits up to 50ms for ac97 busy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Adds vidioc_[g|s]_register handlers. This allows getting/setting register
from em28xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

AC97 register initialization seem to always be needed. This patch fixes audio
for Prolink/Pixelview USB2 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/video/em28xx/em28xx-core.c: In function 'em28xx_set_audio_source':
drivers/media/video/em28xx/em28xx-core.c:276: warning: 'no_ac97' may be used uninitialized in this function

This looks like a genuine bug to me.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>