The PCnet32 driver always passed the the size of the largest possible packet
to the pci_dma_sync_single_for_cpu and pci_dma_sync_single_for_device.
This results in a fairly large "colateral damage" in the caches and makes
the flush operation itself much slower.  On a system with a 40MHz CPU this
patch increases network bandwidth by about 12%.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fixes MODPOST warnings similar to:

WARNING: drivers/net/tulip/de2104x.o - Section mismatch: reference to
.init.text:de_init_one from .data.rel.local after 'de_driver' (at offset 0x20)
WARNING: drivers/net/tulip/de2104x.o - Section mismatch: reference to
.exit.text:de_remove_one from .data.rel.local after 'de_driver' (at offset 0x28)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Add link detection
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix a oops on module removal due to deallocating memory before unregistring
driver Fix a NULL pointer dereference when dev_alloc_skb fails
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix a typo, wrap lines on 80-th column, change KERN_ERR to KERN_INFO for
link status message
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Revert 7628b0a8.  Thomas Bachler
reports:

  Commit 7628b0a8 (drivers/net/tulip/dmfe:
  support basic carrier detection) breaks networking on my Davicom DM9009.
  ethtool always reports there is no link.  tcpdump shows incoming packets,
  but TX is disabled.  Reverting the above patch fixes the problem.

Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Thomas Bachler <thomas@archlinux.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Returns NETDEV_TX_BUSY when BD ring is full.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix broken BD processing code.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface.  If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).

	This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover.  This insures that switches are kept up to date
for all cases.

	"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch.  His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

	Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs.  Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself.  Double unregister is not an
issue.

	Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

CONFIG_PARAVIRT broke old glibc bootup: it silently turned off the
selectability of CONFIG_COMPAT_VDSO and thus rendered distro kernels
unbootable on old-style VDSO glibc setups.

the proper solution is to keep COMPAT_VDSO available - if a hypervisor
needs any modification of that concept then we'll judge those changes in
full context, once those changes are submitted.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
  backlight: Allow enable/disable of fb backlights, fixing regressions
  backlight: Fix nvidia backlight initial brightness

there's a new NMI watchdog related problem: KVM crashes on certain
bzImages because ... we enable the NMI watchdog by default (even if the
user does not ask for it) , and no other OS on this planet does that so
KVM doesnt have emulation for that yet. So KVM injects a #GP, which
crashes the Linux guest:

 general protection fault: 0000 [#1]
 PREEMPT SMP
 Modules linked in:
 CPU:    0
 EIP:    0060:[<c011a8ae>]    Not tainted VLI
 EFLAGS: 00000246   (2.6.20-rc5-rt0 #3)
 EIP is at setup_apic_nmi_watchdog+0x26d/0x3d3

and no, i did /not/ request an nmi_watchdog on the boot command line!

Solution: turn off that darn thing! It's a debug tool, not a 'make life
harder' tool!!

with this patch the KVM guest boots up just fine.

And with this my laptop (Lenovo T60) also stopped its sporadic hard
hanging (sometimes in acpi_init(), sometimes later during bootup,
sometimes much later during actual use) as well. It hung with both
nmi_watchdog=1 and nmi_watchdog=2, so it's generally the fact of NMI
injection that is causing problems, not the NMI watchdog variant, nor
any particular bootup code.

[ NMI breaks on some systems, esp in combination with SMM -Arjan ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

do not use default=y for CONFIG_VMI (we do not do that for any driver or
special-hardware feature): the overwhelming majority of Linux users does
not need it, and interested users and distributions can enable it
as-needed.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Clarify the description of the CONFIG_VMI option: describe the reality
that VMI is a VMWare-only interface for now. Once that changes and
another hypervisor adopts the VMI ABI we can change the text.

As can be seen from the Xen paravirtualization patches submitted to lkml
the Xen project has chosen its own, non-VMI interface between Xen and
the para-Linux - so remove Xen from the description.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Temove the mistaken turning on of NO_IDLE_HZ on x86+PARAVIRT kernels.

It's an obsolete, limited form of dynticks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

CT based mach64 cards were reported to hang on sparc64 boxes when
compiled with gcc-4.1.x and later.

Looking at this piece of code, it's no surprise.  A critical
delay was implemented as an empty for() loop, and gcc 4.0.x
and previous did not optimize it away, so we did get a delay.

But gcc-4.1.x and later can optimize it away, and we get crashes.

Use a real udelay() to fix this.  Fix verified on SunBlade100.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

  CC      arch/i386/kernel/vmi.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c: In function 'vmi_map_pt_hook':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE0' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE1' undeclared (first use in this function)
make[2]: *** [arch/i386/kernel/vmi.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add some documentation for the new and very useful io-accounting feature.
It's being added to Documentation/filesystems/proc.txt
Signed-off-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the following compile error:

  MODPOST 327 modules
WARNING: "aty_st_lcd" [drivers/video/aty/atyfb.ko] undefined!
WARNING: "aty_ld_lcd" [drivers/video/aty/atyfb.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

"drivers/char/epca.c:2741: warning: 'get_termio' defined but not used"
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Doing something like this on a two cpu system

  # echo 0 > /sys/devices/system/cpu/cpu0/online
  # echo 1 > /sys/devices/system/cpu/cpu0/online
  # echo 0 > /sys/devices/system/cpu/cpu1/online

will give me this:

  =======================================================
  [ INFO: possible circular locking dependency detected ]
  2.6.21-rc2-g562aa1d4-dirty #7
  -------------------------------------------------------
  bash/1282 is trying to acquire lock:
   (&cpu_base->lock_key){.+..}, at: [<000000000005f17e>] hrtimer_cpu_notify+0xc6/0x240

  but task is already holding lock:
   (&cpu_base->lock_key#2){.+..}, at: [<000000000005f174>] hrtimer_cpu_notify+0xbc/0x240

  which lock already depends on the new lock.

This happens because we have the following code in kernel/hrtimer.c:

  migrate_hrtimers(int cpu)
  [...]
  old_base = &per_cpu(hrtimer_bases, cpu);
  new_base = &get_cpu_var(hrtimer_bases);
  [...]
  spin_lock(&new_base->lock);
  spin_lock(&old_base->lock);

Which means the spinlocks are taken in an order which depends on which cpu
gets shut down from which other cpu. Therefore lockdep complains that there
might be an ABBA deadlock. Since migrate_hrtimers() gets only called on
cpu hotplug it's safe to assume that it isn't executed concurrently on a

The same problem exists in kernel/timer.c: migrate_timers().

As pointed out by Christian Borntraeger one possible solution to avoid
the locking order complaints would be to make sure that the locks are
always taken in the same order. E.g. by taking the lock of the cpu with
the lower number first.

To achieve this we introduce two new spinlock functions double_spin_lock
and double_spin_unlock which lock or unlock two locks in a given order.

Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Christian Borntraeger <cborntra@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426

The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.

It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.

Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).

This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Removes unused 'flags' variable from setup_IO_APIC_irq().
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ipmi_si_intf tries to access default ports, if no device could be found
elsewhere.  On PPC we have a function to check, if these legacy IO ports
are accessible.  This patch adds a check for these ports on PPC.  This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

- In fact we don't have to fail if AOP_TRUNCATED_PAGE was returned from
  prepare_write or commit_write. It is beter to retry attempt where it
  is possible.

- Rearange ecryptfs_get_lower_page() error handling logic, make it more clean.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

- Currently after path_lookup succeed we dot't have any guarantie what
  it is DIR. This must be explicitly demanded.
- path_lookup can't return negative dentry, So inode check is useless.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Acked-by: Michael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

  Testing NMI watchdog ... CPU#0: NMI appears to be stuck (54->54)!
  CPU#1: NMI appears to be stuck (0->0)!

Keep the PIT/HPET alive when nmi_watchdog = 1 is given on the command
line.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.

Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks".  With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar.  One place was missed.

This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong.  On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Critical fixes for SMP.

Fix a couple functions which needed to be __devinit and fix a bogus parameter
to AP startup that just so happened to work because the low virtual mapping of
memory was still established.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use para_fill instead of directly setting the APIC ops to the result of the
vmi_get_function call - this allows one to implement a VMI ROM without
implementing APIC functions, just using the native APIC functions.

While doing this, I realized that there is a lot more cleanup that should have
been done.  Basically, we should never assume that the ROM implements a
specific set of functions, and always allow fallback to the native
implementation.

This is critical for future compatibility.
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

More goo from hrtimers integration.  We do compile and run properly with NO_HZ
enabled.  There was a period when we didn't because of a missing export, but
that was since fixed.

And with the clocksource code now firmly in place, we can get rid of code that
fixes up the wallclock, since this is done in the common infrastructure.  This
actually fixes a timer bug as well, that was caused by do_settimeofday no
longer being callable with interrupts disabled due to the use of
on_each_cpu().
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The time_init_hook in paravirt-ops no longer functions in the correct manner
after the integration of the hrtimers code.  The problem is that now the call
path for time initialization is:

  time_init :
       late_time_init = hpet_time_init;

  late_time_init -> hpet_time_init:
       setup_pit_timer (BAD)
       do_time_init --> (via paravirt.h)
          time_init_hook --> (via arch_hooks.h)
              time_init_hook (in SUBARCH/setup.c)

If this isn't confusing enough, the paravirt case goes through an indirect
function pointer in the paravirt-ops table.  The problem is, by the time the
paravirt hook is called, the pit timer is already enabled.

But paravirt guests have their own timer, and don't want to use the PIT.
Rather than intensify the struggle for power going on here, just make it all
nice and simple and just unconditionally do all timer setup in the
late_time_init hook.  This also has the advantage of enabling timers in the
same place in all code paths, so everyone has the same bugs and we don't have
outliers who break other code because they turn on timer too early or too
late.

So the paravirt-ops time init function is now by default hpet_time_init, which
is the time init function used for native hardware.  Paravirt guests have the
chance to override this when they setup the paravirt-ops table, and should
need no change.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Not respecting udelay causes problems with any virtual hardware that is passed
through to real hardware.  This can be noticed by any device that interacts
with the real world in real time - like AP startup, which takes real time.  Or
keyboard LEDs, which should blink in real-time.  Or floppy drives, but only
when passed through to a real floppy controller on OSes which can't
sufficiently buffer the floppy commands to emulate a zero latency floppy.  Or
IDE drives, when connecting to a physical CDROM.

This was mostly a hack to get the kernel to boot faster, but it introduced a
number of misvirtualization bugs, and Alan and Pavel argued pretty strongly
against it.  We were the only client, and now want to clean up this cruft.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Provide a PT map hook for HIGHPTE kernels to designate where they are mapping
page tables.  This information is required so the physical address of PTE
updates can be determined; otherwise, the mm layer would have to carry the
physical address all the way to each PTE modification callsite, which is even
more hideous that the macros required to provide the proper hooks.

So lets not mess up arch neutral code to achieve this, but keep the horror in
an #ifdef HIGHPTE in include/asm-i386/pgtable.h.  I had to use macros here
because some types are not yet defined in all the include paths for this
header.

This patch is absolutely required for HIGHPTE kernels to operate properly with
VMI.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code.  This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>